25mm EPP SU31. Instruction Manual. Specifications

Transcription

1 25mm EPP SU31 Instruction Manual Specifications Wingspan: 39.4in (1000mm) Length: 42in (1070mm) Wing Area: 448sq in (28.9sq dm) Flying Weight: Approx. 1.5lb ( g)

2 Dear Customer, Congratulations on your purchase of Elite Models SU31 EPP Airplane ARF from Value Hobby. We thank you for your generous support, and hope you enjoy your new airplane. At Value Hobby, we hope to offer competitive prices, good performance, and products that you can setup and use with ease. That s why we extensively researched and tested this airplane, and suggested all the products necessary for you to setup properly. We understand that you have many choices when purchasing, and we are grateful you choose to buy from us. As vendors, one of the most gratifying things for us is to hear from our customers. We would welcome any suggestion to help us improve. Please make us aware of any errors and imperfections in the airplane or the instructions, or about the setup that we suggested. We hope you ll find our setup suggestions to be helpful, and enjoy flying your new airplane. Please feel free to contact us at (630) or us at support@valuehobby.com Disclaimer By purchasing and/or building this model, user assumes ALL liability and risk involved with this product. This model should be built and flown by an experienced pilot and only flown at AMA sanctioned sites. Value Hobby guarantees this model to be free of defects in materials and workmanship at the date of purchase. This warranty does not cover any parts damaged by use or modifications. In no way shall Value Hobby liability exceed the original cost of the purchased model. Further, Value Hobby reserves the right to modify this warranty without notice. Value Hobby has no control over the final stages of assembly or the material used for the final assembly. No liability shall be assumed nor materials used for the final user-assembled product. By the act of using the final product the user accepts all resulting liability. Value Hobby, as a R/C product vendor, provides a top quality airplane and instructions to complete the model. The quality and flight characteristics of the finished model depend greatly on how it is built; we cannot guarantee the performance for the completed model and representations are expressed or implied as to the performance of the completed model. If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately, in new and unused condition. Safety in Assembly During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives. Please follow all safety procedures recommended by the manufacturers of the products you use, and always follow these important guidelines: ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power tools. Safety glasses are the best way to protect your eyes. ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, or tools, especially power tools. Do not cut toward exposed skin with hobby knives. Do not place hobby knives on tables or benches where they can roll off or be knocked off. ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially power tools. ALWAYS keep hobby equipment and supplies out of the reach of children. 2

3 Safety in Flying This is NOT a toy! It is a very high-performance RC airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. ONLY fly your aircraft in a safe, open area, away from spectators and vehicles and where it is legal to fly. NEVER fly over an unsafe area, such as a road or street. Never fly too close to yourself or spectators. Never run your motor inside a house or building with the propeller attached Remove the prop for safety. Required Items Foam Glue Thin CA Hobby Knife Wire Cutters Small Phillips Screwdriver Set Metric Allen Wrenches Scissors Small Pliers Masking tape Before Starting Assembly Examination Unpack your airplane and examine the components. Check for damage of any kind. If you see any damage, please contact Value Hobby immediately. 3

4 Main Parts: 1. Fuselage x 1 2. Wing Panel x 2 3. Horizontal stabilizer x 1 4. Rudder x 1 4

5 Accessories: List: Landing gear wire x 1 Wheel collar x 4 Wood landing gear insert x 1 Foam wheel x 2 M3*12mm self-tapping screw x 1 Tail skid x 1 2.1mm push rod connector x 5 Servo arm extension x 4 M2*6mm screw x 8 M2 nut x 8 Servo mounts for 9g servo x 4 Servo mounts for 17g servo x 4 Control horn type A x 3 Control horn type B x 1 Push rod x 4 Hinges (optional) Wing tube (fiberglass) x 1 Plastic hook x 4 Rubber band x 4 M3*12mm motor mounting screws x 4 150mm hook and loop strap x 1 5

6 RECOMMENDED RADIO EQUIPMENT Product SKU Quantity Radio Flysky FS-i6 Transmitter and Receiver Set FLY-RC Servo Option1: EMAX ES3154 Metal gear digital 17g servo EMX-SV Option2: Towerpro MG90s 9g servo TWP-SV RECOMMENDED SETUP Product SKU Motor GForce E450 Brushless Outrunner Motor( kv) VHB-MT-5297 ESC Hobbywing Flyfun 30A Brushless ESC HWG-SC-0238 Battery GForce Elite Series 30C 1600mah 3S LiPO FLM-LP-2651 Prop 10 x 6 prop GFH-MP-2490 OPTIONAL ACCESSORIES Product SKU Charger GT Power C6 6S LiPO Charger GTP-CH-1427 Foam Glue Thin Foam Safe Glue VHB-AC-2511 Watt Meter GT Power 130A Watt Meter GTP-AC-0591 Connector Female T Connector (5pcs) Male T Connector (5pcs) AMS-AC-1914 AMS-AC-1913 LiPO Bag LiPO Safe Bag RFI-LP

7 Servos installation Step1. Locate the fuselage. Step4. Use foam glue to glue the servo into the servo opening in the fuselage. Step2. Locate two servos and two servo mounts. (We provide two sizes of servo mounts for 9g servo and 17g servo.) Step5. Connect a 12in servo extension into the servo lead. Step6. Use a ruler to cut a slot for the servo lead. Step3. Install the servos into the servo mounts. (You can use the self-tapping screw provided with the servo to secure the servo to the mount, or you can do this in next step.) Step7. Insert the servo lead into the slot.

8 Step8. Install the elevator servo and aileron servos using the same methods. Aileron Servos Linkage Installation Step1. Locate the two M2*6mm bolts, two M2 nut, one pushrod connector, one servo arm and one servo arm extension. Step9. Install the aileron servos into the wing. Step2. Install the arm extension to the servo arm and install the pushrod connector to the extension. Step3. Install the assembled servo arm into the servo using the screw provided with the servo. (Need to center the servo electronically before the installing.) 8

9 Step4. Connect a pushrod to the control horn. (Need to enlarge the hole in the control horn.) Tail and Rudder/Elevator Servo Linkage Installation Step1.Install the servo arms to the rudder servo and elevator servo. Step5. Use the pushrod as the guide, cut a slot on the aileron for installing the control horn. Step6. Use foam glue to install the control horn to the aileron. (Need to cut off the excessive pushrod wire.) Step2. Locate the horizontal stabilizer, control horn and wood control horn mount. Step7. With the aileron centered, tighten the screw to secure the pushrod to the servo arm. Step8. Repeat the previous steps to install the other aileron servo and linkage. 9

10 Step3. Use foam glue to glue the wood mount to the elevator and install the control horn to the elevator. Step5. Apply thin CA to the area between the fuselage and tail. Step4. Insert the horizontal tail into the slot of the fuselage. Adjust the tail to make sure it is 90 degree with the fuselage, as well make sure the distance between one point in the fuselage and left tail wing tip and the distance between that point and right tail wing tip are the same. Step6. Use foam glue to glue the fin together. Step7. Glue the rudder to the fuselage. Make sure that the rudder is in the central line of the fuselage and it is perpendicular to the horizontal tail. 10

11 Landing Gear and Tail Skid Installation Step1. Locate the items as shown. Step8. Cut a slot in the rudder for installing the control horn. Step2. Use two wheel collars to install the foam wheel to the landing gear wire. Step9. Install the rudder and elevator servo linkage using the some methods in the section of aileron servo linkage installation Step3. Install the other foam wheel to the landing wire. 11

12 Step4. Locate the wood landing gear insert. Step7. Cut a slot in the bottom of the fuselage. Step5. Use one M2*16mm self-tapping screw and one wood insert to secure the landing gear into the fuselage. Step8. Insert the tail skid into the slot and apply some thin CA to the slot. Step6. Locate the tail skid. 12

13 Wing installation Step1. Locate four plastic hooks. Step3. Locate the fiberglass wing tube and rudder bands. Step2. Glue them into the slots in the wings. Step4. Insert the wing tube into the fuselage. Step5. Attach two wing panels onto the fuselage along the wing tube. 13

14 Step6. Connect the rubber band to the hooks to make sure the wing panels are secured to the fuselage tightly. Motor Installation Step1. Prepare a 2216/2217 motor with the motor mount installed. Step2. Position the motor onto the plastic motor mount and use a pen to mark the locations. Step3. Drill the mounting holes on the motor mount. (You don t need to drill through the firewall since we provide the self-tapping screws to install the motor.) 14

15 Step4. Install the motor to the motor mount. (Some washers are needed in order to get a 1.5degree right thrust angel.) The slots for battery, ESC and receiver are pre-cut at the factory. Step5. Install the prop to the motor. Recommended CG The recommended CG is mm( in) from the leading edge of the wing. Recommended control throw Aileron: 45 degrees up and down Elevator: 50 degrees up and down Rudder: 50 degrees right and left 15

16