High Performance Live Centres Types CS/CE

Transcription

1 Precision and Reliability first Reliable bearing protection through coolant deflector + TOP-SEA-SYSTEM High Performance ive Centres Types CS/CE Short design with small housing diameter For mechanical manufacturing

2 High Performance ive Centres Types CS/CE Types CS/CE Compact precision design for mechanical processing With its short anti-vibration design, the small housing diameter and precision bearings our types CS and CE are ideal for a wide range of mechanical manufacturing operations. Bearings are reliably protected from the ingress of dirt and coolant by the deflector integrated into the centre spindle and the proven TOP-SEA-SYSTEM. The service friendly design assures minimum repair costs: Needle bearings with outer ring. In case of needle bearings wear the housing is not damaged and can be re-used with new replacement bearings. 4 5 High concentricity accuracy tested under axial load, guaranteed by test report Coolant deflector a deflector integrated into the throughhardened centre spindle deflects most of the coolant TOP-SEA-SYSTEM undeflected residue is wiped off the seal and flows through the drain groove (see page ) Precision bearings bearing seats of housing and centre spindle are precision ground and matched to the bearings Housing of high tensile alloyed tool steel. Housing head and shank are case-hardened for protection against damage

3 High Performance ive Centre Type CS small housing diameter, short design Type CS Centre spindle 60 with coolant deflector and TOP-SEA-SYSTEM G G Runout max mm also available with 0.00 mm with test report Application use where the workspace is constrained or limited for turning, high performance turning, hard turning, fine turning, cylindrical grinding A C B Coolant deflector + TOP-SEA-SYSTEM Coolant strikes the circular deflecting surface and its largest part is deflected away from the centre housing. The residue is wiped from the seal and flows through the drain groove. Type CS I.No. 600S 0A 600S 0A 600S A Morse taper G 5 46 A B C G M5x.5 M8x.5 M48x.5 Workpiece weight max. dan* r.p.m. max.* Radial/axial load graph RY/AY RY/AY RY/AY raw-off nut (page 4) M5IN804 M8IN804 M48IN804 *observe the load graphs RY Radial and axial loads for a bearing life of 0 operating hours Radial Type CS workpiece weight dan 5 0 radial load dan AY Axial Type CS axial load dan r.p.m. r.p.m. All dimensions in mm

4 High Performance ive Centre Type CE small housing diameter, short design Type CE Centre spindle with internal taper :7.5 for interchangeable inserts with coolant deflector and TOP-SEA-SYSTEM G A K G Runout max mm inside the internal taper also available with 0.00 mm with test report Runout of the system can be minimized by twisting the insert in the internal taper A B C Nut 4x90 Application use where the workspace is constrained or limited for turning, high performance turning, hard turning, fine turning, cylindrical grinding G Multiple options through a choice of 8 interchangeable inserts M M raw-off nut I.No. G M M M5IN804 M5x.5 55 M8IN804 M8x.5 58 M48IN804 M48x.5 75 Type CE I.No. 600E 0A 600E 0A 600E A Morse taper 4 A 0 5 G 5 46 K 5 A 5 B C G M5x.5 M8x.5 M48x.5 SW 6 6 r.p.m.max oad The radial load of type CE is restricted by the interchangeable inserts (page 5) raw-off nut M5IN804 M8IN804 M48IN804 Suitable inserts (page 5)

5 High Performance ive Centre Type CE Interchangeable inserts taper :7.5, in gauge accuracy Form A0, 60 K l K Form B, centre 60 for centreless workpieces, B Form AS, 60 slim, extended A Form C, centre 60 for centreless workpieces, external angle 60 for hollow parts, spanner flat (SW) d B Form AK0P, 60 / extended Form, centre 60 for centreless workpieces, spanner flat (SW) B Form A, 60 for hollow parts spanner flat (SW) Form A0HM, 60 with carbide insert Basic centre Type:CE Interchangeable inserts Radial load max. dan Insert dimensions Thread SW Taper dimensions taper :7.5 I.No. I.No. B d A K K l 48AO M4x.5 600E 0A 600E 0A 600E A 48AS M4x.5 48AKOP M4x.5 48A SW4 48B x 45 M4x.5 48C x 45 SW x6 45 SW4 48AOHM M4x.5 484AO M8x.5 484AS M8x.5 484AKOP M8x.5 484A SW 484B x 5 M8x.5 484C x SW x 64 SW4 484AOHM M8x I.No. P 0 Content g Installation paste Makes insert change easier. Apply thinly and evenly to the insert taper. Changing of inserts epending on the style the insert can be removed by its draw-off thread and draw-off nut or with spanners applied to the spanner flats. 5

6 Precision and Reliability first Karl Bruckner GmbH Präzisionswerkzeugfabrik Bruckwiesenstrasse WEINSTAT GERMANY Phone +49 (0) Fax +49 (0) info@karlbruckner.de Subject to technical modifications Karl Bruckner GmbH CS/CE 086 E High performance ive Centres and Face rivers