Mirage 9x9, 8x8 and 7.5 Mirage Gazebo Assembly Instructions
|
|
- Alberta Russell
- 5 years ago
- Views:
Transcription
1 Mirage 9x9, 8x8 and 7.5 Mirage Gazebo Assembly Instructions For technical support, contact the Wood Products Division at
2 Measure the height of the top of the spa siding. This is the suggested height for positioning the lower lattice panel. Mark the same distance from the bottom of a post. Lay out a Mid (large) Panel and an Upper (small) Panel with staples down. Line up the bottom of a Mid Panel with the mark and position an Upper Panel to the top of the post. Attach the Mid Panel to a post with two 2 screws. Be careful that the chuck of the drill does not grind against the lattice. 2
3 Attach Upper Panel to post with two 2 screws and attach both panels to the opposite post. Attach small corbels in the corners top and bottom with 2 screws, and attach corbels the same way at the other end of the wall. Now that the back wall is constructed, move it into place. You can lean it against the spa while you proceed to the next wall. 3
4 Build the next wall using only one post. This will be the side opposite the bar. Position the lattice panels the same as before, with the staples down. Which side the bar is to be placed on will determine the position of this post. Carrying the wall over to the others will take two people, with one holding the post and the other holding the loose ends of the lattice panels. Attach this wall to the back wall with two 2 screws in the Upper Panel and two in the Mid Panel. Attach corbels in the corner at which the two walls come together. 4
5 Make the same measurement as on the first wall and line up the top of the Mid Panel to it. Attach Mid Panel in this position and attach an Upper panel in the same place as on the other walls, staples down. Attach a corbel in the upper corner. 5
6 Carry the wall over to the gazebo like the previous wall. Attach the loose ends to the post of the back wall. Attach a small corbel at the top where the two walls meet. Lay out the four roof frame pieces, flat ends to beveled ends, pilot holes (on beveled ends) facing out. Attach each corner with two 3 screws. 6
7 Attach a rafter with a 3 screw while the other end is being held. Attach the other end to the crown. Attach the opposite rafter next so that the two will support each other. Move on to the other two rafters. For the last one you will probably need to lift the center up until all four come together. Each of the four roof panels comes in two pieces, which are numbered so that you can match them. 7
8 Set the roof panels in place with the staples up. The top of the lower piece fits into the groove in the upper piece. Connect each side of the panel with four 2 screws. Once the roof panels are in place, slide the roof on (that will require at least two people). The frame will slip over the posts. Attach the roof frame to each post. 8
9 Attach the 2x2 adapter blocks, one on each side of the Gazebo opening, with two 2½ screws. Attach a large corbel with two 2½ screws on each side of the gazebo opening also. To attach the bar, have one person (or two) hold it in place and center the ends of the bar on the posts, keeping the surface of the bar flush to the top of the Mid Panel. Insert a toenail screw (a 3 screw diagonally through the bar into the lattice) in each end of the bar. 9
10 Attack a bar (mid-sized) corbel under each end of the bar (up against the understructure block), using two 2½ screws for each. Make a pilot hole from behind the bar at each end, then insert 2 ½ screws into each. 10
11 To build stools, attach each leg pair with four 2 ½ screws. Attach each of the two braces with two 2½ screws at each end. To build wine rack, center the runners on the header and attach each with two 2½ screws. 11
12 Find the center of the Upper Panel on the bar side. We suggest making a small mark. Find the center of the wine rack. Make three pilot holes in the header and put 2½ screws in place Hold the wine rack centered on the 2x2 of the Upper Panel and insert the three screws. Attach towel hook in a place of customer s preference. The gazebo is now complete. 12
Assembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
More informationCAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo:
Octagon Wood Gazebo Kit Contents Hardware included for assembling your gazebo: 5/16" Lag Bolts Use to fasten post to floor 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten
More informationAMISHGAZEBOSHOP.COM VINYL GAZEBO KIT CONTENTS
VINYL GAZEBO KIT CONTENTS Hardware for assembling your gazebo (provided): 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten rafters to rafter header fasten benches & cupola
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationWooden Rectangle Pergola Assembly Manual
Wooden Rectangle Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced
More informationINSTALLATION INSTRUCTIONS FOR ULTRA LATTICE AND ALUMAWOOD ARBORS
INSTALLATION INSTRUCTIONS FOR ULTRA LATTICE AND ALUMAWOOD ARBORS GENERAL INFORMATION: Lattice arbors are designed to be freestanding or attached. They are designed to resist a 10 lb. to 30 lb. per square
More informationKIT ASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS We have designed these instructions as a stepby step procedure to simplify the assembly process. Nevertheless, we do recommend including someone with carpentry expertise on your
More informationVinyl Gazebo Instructions
P a g e 1 Vinyl Gazebo Instructions 10 Vinyl Gazebo Shown Thank you for the purchase of your New Gazebo. Depending on the size of your Gazebo, installation can usually be completed in 1 to 2 days. These
More informationCountryAccents Pergola Assembly Instructions
CountryAccents Pergola Assembly Instructions Options 11 2" Squares Lattice Railing Gingerbread Scroll (For 5" Posts Only) Site Preparation Site preparation for either the round column or the 5" post pergola
More informationOctagon Vinyl Gazebo Assembly Instructions
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationAssembly Instructions
10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationOwner's Manual & Assembly Instructions
Owner's Manual & Assembly Instructions TQ01 Universal Attic Kit Model No. AT101 IMPORTANT: Before you start, remove Owner's Manual & Assembly Instructions from main carton of your storage building and
More informationx16 GAZEBO ASSEMBLY INSTRUCTIONS
36 1 x16 GAZEBO ASSEMBLY INSTRUCTIONS Assembly with more than one person recommended 0 L:\WP51\Instructions\SOLARIUMS INSTRUCTION BOOKS\36\ZZZ-05.36.0810-1.GP.EN.doc Step 1: Assemble beams A and B using
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationGreenhouse Assembly Instructions
Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800
More informationParts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece)
[1] - 23.5 x 35.5 Top [8] - Drawer Support Rods Parts List [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench [2] - Upper Base left End (1 pieces) [9] - Media Supports (1 pieces) [16] - loor Guides
More informationCountry Cabin. Assembly Manual. HomePlace Structures
Country Cabin Assembly Manual Country Cabin Assembly Manual revised 3/20/10 Dear Customer, Thank you for your purchase of our Country Cabin. The craftsmanship and detail in this building is unmatched.
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e Download 12,000 More Shed Plans
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e Download 12,000 More Shed Plans Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationBEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2
BEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2 Cutting & Drilling Cut 2 top rails out of 1 x 3s. Each will be 8 1/2 long. Drill 1 pocket hole on the inside bottom center. This will connect the center
More informationVinyl Privacy & Picket Gates
FREEDOM-WEB Privacy & Picket s INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your product,
More informationAssembly Book. 10' x 12' the Cambridge II. revised June 13, 2014
Assembly Book revised June 13, 2014 the Cambridge II 10' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Belmont with pocket doors. Building Size 12'x16' or 12'x20' Revised January 10, 2012
Best Barns USA Assembly Book Revised January 10, 2012 SAMPLE INSTRUCTIONS the Belmont with pocket doors Building Size 12'x16' or 12'x20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive
More informationGardman Lean-to Greenhouse Assembly Instructions
Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free
More informationOriental Pagoda Assembly Instructions
Oriental Pagoda Assembly Instructions English SS136A Before assembly We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction
More informationCommercial Wine & Liquor Display. Double Displays
Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display
More informationx16 GAZEBO ASSEMBLY INSTRUCTIONS
adlonco@hotmail.com 36-3 1 x16 GAZEBO ASSEMBLY INSTRUCTIONS Two or more adults required for assembly 0 ZZZ-05.36-3.117-15.GP.EN.HER.doc Before you assemble the Gazebo It is important that this gazebo be
More informationRequired Tools: Suggested Additional Tools: 1 Cordless Drill with Robertson Bits 1 Ratchet Wrench 1 7/16 or 11mm socket 1 7/16 or 11mm Gear Wrench
Thank you for your recent purchase of a Cabinets by Hayley garage cabinet system. You are about to experience the best made cabinets that you can purchase. Cabinets by Hayley are designed for beauty and
More informationOctagon Greenhouse Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER R H
INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER 10.5.2016 2-1- 3/16" 11/16" 8" 8 O 2-7/8 Ø2-7/8" 3-1/2 3-1/2" 12-9/16 12-9/16" PLEASE NOTE: These instructions are specific to a particular
More informationWAREHOUSE HANGER INSTALLATION INSTRUCTIONS R H INS T A L L A TIO N INS T R U C TIO N S
INS T A L L A TIO N INS T R U C TIO N S WAREHOUSE HANGER NOTE: Due to the size and weight of the Warehouse Hanger it is recommended that this Hanger be installed on 3 4 or wider doors. 10.11.2016 2-3/16"
More informationStrata. urniture. Addison Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 Back Panel x 1 with
More informationOctagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationPergola Installation Instructions
Pergola Installation Instructions TOOLS REQUIRED HAMMER DRILL 1/2 MASONRY BIT PENCIL DRILL 3/16 DRILL BIT LEVEL SQUARE LADDER WRATCHET & SOCKETS RUBBER MALLET 2 TAPE MEASURE Column/Post Placement Table
More information12x12 Pavilion. Assembly Manual
12x12 Pavilion Assembly Manual 12x12 Pavilion Assembly Manual Congratulations on purchasing your new Pavilion. Thank You for your purchase and Welcome to the YardCraft Famiy. This manual is designed to
More informationPacifica Pool House. Assembly Manual. Toll Free: Hours: 9-5 Monday-Friday EST. Package ships as shown. Suncast Corporation
Pacifica Pool House Assembly Manual Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST Package ships as shown Simpson Hurricane Straps Double Insulated Raised-Panel Door in back wall (71 x71 Total opening)
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationBarnCraft Rolling Barn Doors
arncraft Rolling arn Doors Assembly Instructions Looks so good, you ll arncraft think Collection it s wood. The Premium Rolling arn Doors DIMNSIONS arncraft 8'0" arn Door arncraft 6'8 arn Door Glas 8"
More informationAssembly Book. the Fairview. Building Size 12'x12' Revised July 25, 2012
Assembly Book Revised July 25, 2012 the Fairview Building Size 12'x12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationx12 GAZEBO ASSEMBLY INSTRUCTIONS
30 10 x1 GAZEBO ASSEMBLY INSTRUCTIONS Assembly with more than one person recommended 0 L:\WP51\Instructions\SOLARIUMS INSTRUCTION BOOKS\30\ZZZ-0.30.0807-1.GP.EN.doc Step 1: Assemble beams A and B using
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More information3 D Printer Enclosure Assembly Instructions
3 D Printer Enclosure Assembly Instructions Tools Required: 2.5 mm Allen wrench (included) Phillips screwdriver Adjustable Wrench Parts Included: Plexiglas Back with fan and filters installed (29.5 x 35.5
More informationParveneer Positive Pressure Fire Rated Frames Double rabbet with T stop for 20 minutes
Section P/J Page 1 Double rabbet with T stop for 20 minutes Smoke seals are installed in the frame, not the door Section P/J Page 2 Throated jamb with T stop for 20 minutes Smoke seals are installed in
More informationASSEMBLY INSTRUCTIONS FOR 14 x 14 SONOMA ARCHED TOP PERGOLA : OPTIONAL SIDEWALL WINDOW LATCHES Wall Panel Batten Strip Top Cap For Wall Base Beam For
ASSEMBLY INSTRUCTIONS FOR 14 x 14 SONOMA ARCHED TOP PERGOLA : OPTIONAL SIDEWALL WINDOW LATCHES Wall Panel Batten Strip Top Cap For Wall Base Beam For Wall Size: 60.8 1543mm Size: 60 1520mm 4 Panel Wall
More informationINS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER
INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil
More informationStrata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached
More informationBUILDING THE BASIC SHED. Step A: Build the Foundation & Floor Frame
BUILDING THE BASIC SHED Step A: Build the Foundation & Floor Frame 1. Excavate the building site and add a 4" layer of compactible gravel. If desired, add an extension to the base for the optional wood
More informationOn-Roof Mounting Sets for Flat-Plate Collectors
Engineering Submittal Sheet Installation sets for collectors Fig. 1 Installation set for 2 collectors 1 basic installation set, 1 extension installation set Basic installation set for each collector array
More informationx12 GAZEBO ASSEMBLY INSTRUCTIONS
adlonco@hotmail.com 30 10 x1 GAZEBO ASSEMBLY INSTRUCTIONS Assembly with more than one person recommended 0 ZZZ-0.30.100-1.GP.EN.HER.doc Before you assemble the Gazebo It is important that this gazebo be
More informationAssembly Book. 10' x 16' the Cambridge II. revised July 15, 2014
Assembly Book revised July 15, 2014 the Cambridge II 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the
More informationBuilding an Elevated Garden Bed & Hydroponic Table
Building an Elevated Garden Bed & Hydroponic Table Materials: Lumber (2x4, 2x6, 1x4), Exterior Grade Wood Screws (2 1/2 & 1 5/8 ) and Hardware Cloth (enough to cover a 24 x48 area) Tools: Cordless Drill
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H
INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS
More informationWith Illustrations, Blueprints & Step By Step Details Brought To You By ShedPlansz.Com Click Here To Get More Shed Plans
12 X 8 Shed Plans With Illustrations, Blueprints & Step By Step Details Brought To You By ShedPlansz.Com Click Here To Get More Shed Plans Blueprints And Diagrams Instructions For Building The Shed
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationAssembly Instructions
Assembly Instructions T Tinwell picnic bench Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to familiarise yourself with the assembly process
More informationPrecut Value Shed Manual Gambrel Barn
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationTUSCANY INSTRUCTIONS CODE: 0096 TOLL FREE/SANS FRAIS: _Tuscany_11x11_Instructions_V1.2. Footprint Plan.
INSTRUCTIONS CODE: 0096 11'-6 7 8" [353 cm] 10'-11 1 4" [333 cm] 6'-9" [206 cm] 9'-9 15 16" [300 cm] 9'-7 1 4" [293 cm] Front Elevation Footprint Plan 0096_Tuscany_11x11_Instructions_V1.2 EN TOLL FREE/SANS
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised December 6, 2013 the Denver-R 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More information10 Octagon Cedar Gazebo Assembly Instructions
10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions
More informationClassic Saltbox Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box
More informationMILANO INSTRUCTIONS CODE: 0093 TOLL FREE: _Milano_11x11_Instructions_V1.2. Front Elevation Plan View Footprint 12'-0" 11' "
INSTRUCTIONS CODE: 0093 12'-0" 11'-0 3 4 " 12'-0" 6'-9" 9'-4 15 16 " 11'-0 3 4 " 12'-0" Front Elevation Plan View Footprint 0093_Milano_11x11_Instructions_V1.2 EN IMPORTANT CODE: 0093 TOOLS NEEDED BEFORE
More informationINSTALLATION GUIDE. Flat Roof Homesheds TM. Onto Concrete BEFORE YOU START TOOLS REQUIRED
INSTALLATION GUIDE Flat Roof Homesheds TM Onto Concrete BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Flat Roof Homeshed.
More informationHeartland Pergola. Assembly Manual
Heartland Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationPine Log Cabin and Cape Cod Playhouse
Pine Log Cabin and Cape Cod Playhouse Assembly Manual Pine Log Cabin Assembly Manual revised 7/15/02 Dear Customer, Thank you for your purchase of our Pine Log Cabin Playhouse. The craftsmanship and detail
More informationChapter 13 SQUARES HOW TO CHOOSE AND USE THEM TM The Types and Uses section provides you with a list of
Chapter 13 SQUARES HOW TO CHOOSE AND USE THEM The Types and Uses section provides you with a list of the types of squares. These pages should help you select the right square for the job. The Using Squares
More informationEnsure there is reasonable access for materials and working space, ensure the shed site is level and consider the disposal of run-off water.
INSTALLATION GUIDE TM Flat Roof Homesheds THE POTTER BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Potter Flat Roof
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationAssembly Book. the Brandon Building Size 12' x 20' Revised September 13, 2017
Assembly Book Revised September 13, 2017 the Brandon Building Size 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted. Under the
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationSunrise Deck Assembly Instructions for Kingston Left
Sunrise Deck Assembly Instructions for Kingston Left It s easiest to build the deck frame first like it will be lying on its back and then after all 4 legs and horizontals are in place, tip the deck toward
More informationTop Mount Ultra Modern Hanger
Top Mount Ultra Modern Hanger ASSEMBLY INSTRUCTIONS TOP MOUNT ULTRA MODERN HANGER Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits and Phillips Bit Socket Wrench with 9/16
More informationWINE DISPENSING SYSTEM MODEL: DYWS4
WINE DISPENSING SYSTEM MODEL: DYWS4 Trim Kit Part Number AWSTK24 INSTALLATION INSTRUCTIONS IMPORTANT: The wine dispensing utilizes a thermo-electric cooling system that can normally cool the bottle bay
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 19, 2017 the Millcreek 12'x 20' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationE-Z GROW HOBBY GREENHOUSE. I n s t r u c t i o n M a n u a l & D i s c l a i m e r s
E-Z GROW HOBBY GREENHOUSE I n s t r u c t i o n M a n u a l & D i s c l a i m e r s Contractors/Installers Note: This manual is the property of the customer. Please leave it in the possession of the customer.
More informationGarden. Newland picnic bench. Package contents. Tools required ASSEMBLY INSTRUCTIONS
Garden Furniture Direct T: 03333 448 121 ASSEMBLY INSTRUCTIONS Newland picnic bench Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to familiarise
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More informationSide DuraRac Installation Instructions
Side DuraRac Installation Instructions Ford Transit Med/ High Roof Full Size Van (129.9 or 147.6 Wheelbase) Frame Kit Part Number CRC 22 1020 001 Revision 1.0 11/12/14 STEP 1. These instructions are based
More information9 X 9 REMOVABLE TYPE ALUMINUM WINDOW BARS INSTALLATION INSTRUCTIONS Import Note : 9 X 9 Spacing Removable Type Installation is covered in this
Import Note : 9 X 9 Spacing Removable Type Installation is covered in this Instruction. Removable Bars Only Mount in Recess Position ( Between Window Jamb/ Frame ) The spacing between horizontal bars is
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised February 4, 2016 the Millcreek-R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationFLOW HIVE ASSEMBLY GUIDE. If we look after the bees they will look after us, and the honey really is an amazing bonus. Flow Hive Hybrid 3 Frame
AUSTRALIAN MADE If we look after the bees they will look after us, and the honey really is an amazing bonus. FLOW HIVE ASSEMBLY GUIDE Flow Hive Hybrid 3 Frame Read all instructions first. If you are unfamiliar
More informationPRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR & Assembly Installation Instructions 4884 HSD Standard Sliding Door Components Some Considerations When Choosing Your Stall System - 1
More informationBlokes Shed INSTALLATION INSTRUCTIONS Custom Design & Build. Nationwide Delivery
Blokes Shed 10 Year Guarantee On Sanders workmanship Made in NZ Using NZ timber supplies 40+ Years Experience In business since 1975 Professional Install Available NZ wide Nationwide Delivery Available
More informationAssembly Instructions
Assembly Instructions T Tinwell picnic bench Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to familiarise yourself with the assembly process
More informationAssembly Book. the Brandon. Building Size 12'x12' or 12'x16' Revised September 13, 2017
Assembly Book Revised September 13, 2017 the Brandon Building Size 12'x12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted.
More informationINSTALLATION GUIDE. Flat Roof Homesheds TM BEFORE YOU START TOOLS REQUIRED
INSTALLATION GUIDE Flat Roof Homesheds TM BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Flat Roof Homeshed. Read these
More informationROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door
ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials
More information50 W ide. Future Trac G able E nd. Installation Instructions AIGE
G able E nd W ide TopTec Products, LLC 7601 Highway 221 Moore, SC 29369 Phone: (800) 845-2830 Fax: (800) 921-77 e-mail: sales@toptecproducts.com www.toptecproducts.com AIGE 2003915 General Information
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e Download 12,000 More Shed Plans
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e Download 12,000 More Shed Plans Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationKeystone Garage Assembly Manual
Keystone Garage Assembly Manual 14x24 Garage Kit ships as shown Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST 13 8 deep AMISH ORIGINAL KEYSTONE 14x24 GARAGE s p e c i f i c a t i o n s Optional
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More informationContour Hanger ASSEMBLY INSTRUCTIONS
Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationIndustrial Hanger ASSEMBLY INSTRUCTIONS
Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationBlue Ridge Yurts Assembly Instructions 10 Walls
Blue Ridge Yurts Assembly Instructions 10 Walls Thank you for purchasing a Blue Ridge Yurt. We suggest you invite several friends to help you set up your yurt. Follow the steps in order and call us if
More information