Qwik-Fence Installation Instructions

Size: px
Start display at page:

Download "Qwik-Fence Installation Instructions"

Transcription

1 Qwik-Fence Installation Instructions 1

2 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate safety precautions must be used during installations. The product may be unstable during installation; accordingly - temporary bracing should be implemented until all hardware is tightened and the product is properly anchored to the floor. Permanent field bracing (Not supplied) may be installed at installer s/owner s discretion. Installation problems arising from job site conditions should be referred to a professional installer. Refer product assembly questions to Folding Guard. Self-Tapping Screw Installation Recommendations: When installing self-tapping screws use a standard variable speed screw gun equipped with an adjustable clutch or depth locating nosepiece. Take care not to over tighten or strip, set the drill accordingly. DO NOT USE IMPACT TYPE GUN WHEN INSTALLING SELF-TAPPING SCREWS. Securely clamp component parts in place before attaching with self-tapping screws. Tools Required: 5 / 16 Socket Drill Bit Attachment 3 / 8 Masonry Bit 5 / 16 Masonry Bit 5 / 16 Wrench 7 / 16 Wrench 9 / 16 Wrench Hammer Electric Drill (Var. Speed) Tools Recommended: Ladder Carpenters Level Chalk Line Heavy Duty Wire cutters Tools Recommended: Shims (NOT SUPPLIED) Drill Bits (Various) Flat Screw Driver Tape Measure Level Rubber Mallet Prior to Installation: Prior to beginning installation please make sure that you have all the parts required for the assembly Make sure that the installation area is clear of all obstructions. Read thoroughly all the instructions pertinent to your installation. Installer Tips: Installation is best completed with the help of one or two people. Prior to beginning, please read through all instructions pertinent to your installation. (Doors, panels, etc ) Panels are to be installed horizontally between posts, parallel with the ground. Prior to beginning, if at all possible please lay out the parts where they are to be installed. Make sure all posts are installed perpendicular to the floor; shims (NOT SUPPLIED) may be required. Use 2 spacer block (NOT SUPPLIED) to support the panel during the installation. Begin installation at a wall (If your plan calls for a wall connection), corner or an end of a post. Hinge door opening is determined by header bar. Please consult your plan for location and dimensions. Assembly hardware will be installed on the inside of most systems. Installer should eliminate any bolts or hardware protruding into aisle ways or around door openings. 2

3 Hardware List Hardware: ¼ -14 X 1 TEK Self Tapping Screw (F1) KT32046 ¼ -14 X 1½ TEK Self Tapping Screw (F6) (Optional) KT31825 ¼ -20 X ¾ Carriage Bolt (F10) KT /16 Socket (Door Option) (Supplied by Folding Guard) KT ¼ -20 X 1 Carriage Bolt (F2) KT /8 x1 Washer (F7) (Optional) KT33008 ¼ -20 X 1¼ Carriage Bolt (F11) KT21157 ¼ -20 Hex Nuts (F3) KT /8-16 X 3.75 Concrete Anchor (Slide Door Option) (F8) KT52205 ¼ -20 X 1¾ Stop Bolt (F12) (Slide Door Option) KT0299 ¼ X1 Washer (F4) KT /2-20 x 3-3/4 Floor Anchors Plastic Anchor (F13) KT50987 ¼ -14 X 1¼ Slotted Head Screw (F5) KT /8-16 Nut ( Slide Door Option) (F9) KT36106 ½ -14 X 3.75 Concrete Anchor (Post Attachment) (F14) KT

4 Brackets & Assemblies Other Items Included: Replacement Kits Include Hardware to Order Call Panel Clip (B1) KT0201 Floor Bracket (B2) KT0202 Hinge Door Header Bracket (B3)* KT0203 Slide Door Mounting Strip (B5)** KT0205 Slide Door Bracket (B4)** KT0204 Slide Door Bottom Guide Slide Door Guide (B8) ** KT0207 Mesh Clamp (B10)*** KT0209 Slide Door Trolley Assembly (B9) ** KT0208 * Supplied for Hinge Door Assembly Only ** Supplied for Slide Door Assembly Only *** Supplied for Ceiling Kit Assembly Only **** Supplied for Wall Kit Assembly Only 4

5 Brackets & Assemblies Other Items Included: Replacement Kits Include Hardware to Order Call Capping Channel (Optional) (M3) Var. Sizes 48 Part No. QFCC Part No. QFCC-96 Ceiling Angle Kit (C1) *** For 3 w support Part No. CA3 For 4 w support Part No. CA4 For 8 w support Part No. CA8 For 10 w support Part No. CA10 Receiver Door Bar (D1)* KT0212 Wall Kit Angle (W1) **** Part No. WK Door Hinge (D2)* KT0213 Stop Angle (D3)* KT0211 Header Bar 2 X2 (D4)* For 3 w Door Kit Part No. KT0214 For 4 w Door Kit Part No. KT0215 Lock Receiver Bar (D5) ** KT0216 Slide Door Track (D6) ** For S3 Door Part No. SDT-S3 For S4 Door Part No. SDT-S4 For S6 Door Part No. SDT-S6 For S8 Door Part No. SDT-S8 For S10 Door Part No. SDT-S10 * Supplied for Hinge Door Assembly Only ** Supplied for Slide Door Assembly Only *** Supplied for Ceiling Kit Assembly Only **** Supplied for Wall Kit Assembly Only 5

6 Planning & Layout Fig. 1-1 Capping Channel (M3) (Optional) See (Step 10) for installation directions Panel 8 X4 Nominal (M1) Post (M2) Standard 8 Post (M2) May come in: 10, 12 or other Lengths Panel (M1) NOTE: 2 Sweep Space Post base type is supplied per specific application. See plan for exact post location. 6

7 Wall Kit Assembly Step 1: Setting up for installation. Plan the layout of the Qwik-Fence Perimeter Mark Every Post Location Mark Every Door Location To begin installation at a wall or corner. (Fig. 2-1) See Wall Kit Instructions Step 2. To start from a Post (M2) Please skip to Step 3. Fig. 2 1 x6 Fig. 2 2 Step 2: Wall Kit Assembly Attach the provided Wall Kit Angle (W1) to the existing wall with provided Slotted Head Screw (F5) and Plastic Anchor (F6). See Figure 2-2 for reference. Attach the Wire Mesh Panel When attaching the Wire Mesh Panel (M1) DO NOT FORGET to measure 2 from the floor to the bottom of the mesh to ensure fit with the Posts (M2). Use the 5 / 16 Masonry bit to pre-drill the hole for the wall anchor. Insert the Carriage Bolt (F2) through the front of the angle and in the back use the provided Mesh Clamp (B10) to clamp the mesh to the angle, connect all with the Washer (F4) and Nut (F3). Refer to Figures 2-3 and 2-4 for reference. Refer back to Step 1 for further reference. Figure 2-4 shows final assembly including a post (M2) and Wire Mesh (M2). Fig. 2 4 Fig. 2 3 x6 7

8 Step 3: Adding a Post. Space off the Post (M2) to be flush with the end of the currently attached panel(s) (M1). Reference Distances are as follows: Wall to center of First post: 95 Center of Post to Center of Post: 96 Secure the post to the floor using floor anchors (Not Supplied) Recommended: ½ DIA X 3.75 L Anchor You may use holes in the posts (M1) as a drill guide. Refer to Figure (3-2) for reference. Use Figure (3-1) for post orientation. Post & Panel Assembly Inside of Room Fig. 3 1 Step 4: Adding a Panel (M1). Place the panel so that the flanges of panel are facing towards the inside of the room. (DO NOT ghten as that is the last step). See Figure (3 1) for reference. The lower panel should be approximately (two) 2 off the ground (for Standard Installa on). If you have a ver cal post (M2) with a 2 X6 base you may use that post as a spacer by laying that post (M2) on its side. Insert a Panel Clip bracket (B1) around the end wire of the panel (M1) at the corresponding predrilled hole of the post (M2). Refer to Figure (5 1) for reference. Repeat for all the predrilled holes (3/Panel). Fig. 3 2 Step 5: Adding Top Panel (M1) Vertically. Insert a Panel Clip bracket (B1) around the end wire of the panel (M1) at the corresponding predrilled hole of the post (M2). Refer to Figure (5-1) for reference. Repeat for all the predrilled holes. Approximately 2 Panel Clip brackets (B1) per 4 H Panel (M1) Using the provided Carriage Bolt (F2), Hex Nut (F3), Washer (F4) secure the two panels together equally spaced for (three) 3 locations of bolts. Refer to Figure (5-1) for reference. Spaced equally through out the Panel (M1) span. Some cutting may be required See (Step 7). Fig

9 Floor Bracket Assembly Step 6: Adding floor Bracket (B2) (1/Panel). Bend the supplied Floor Bracket (B2) at the perforation. (One per Panel) Hook the Floor Bracket (B2) over the panel (M1) at center. Pre-drill a 5 / 16 hole in the concrete to the depth of (two) 2 inches. Insert the Plastic Anchor (F13) and hammer it in. Insert the Slotted head screw (F5) into the Floor Bracket (B2) and screw it into the Plastic Anchor (F13). Refer to Figure (6-1) for reference. Fig. 6 1 Step 7: Adjusting Panel Size. If size adjustment is required using heavy-duty wire cutters, cut every 1½ horizontal wire. Step 8: Installing a Hinge Door (Optional). See Step 8 (Starting on page 10). Step 9: Installing a Slide Door (Optional). See Step 9(Stating on page 13). Step 10: Installing (Optional) Capping Channel. Install only AFTER the Door Installation. Place the Capping Channel (M3) on top of Finished Post and Panel assembly. The end of the capping channel (M3) should be at the middle of the post (M2). Refer to Figure (10-1) for reference. Using the provided TEK Screws (F1) secure the capping channel (M3) to the post (M2) using the hole in the capping channel (M3) as a pilot hole. Refer to Figure (10-1) for reference. Fig

10 Hinge Door Assembly Fig. 8 1 DOOR POSTS SPACING DOOR #H3 = (94.54cm) inside of posts DOOR #H4 = (125.00cm) inside of posts 10

11 Hinge Door Assembly Step 8: Installing Hinge Door (Optional) Prior to beginning installation make sure that your plan includes a door and that it is a Hinge door. Prior to beginning installation make sure that the door is manufactured per your requirements and matches the overall plan layout in terms of hinge and lock. Prior to beginning make sure that all the parts required for a Hinge door assembly are included. Prior to beginning make sure that your side posts are already installed and are secure in their location. The spacing for the Hinge doors are as follows: H X 96 (From the ground to the top of the clearance for the door) 37.5 header width. H X 96 (From the ground to the top of the clearance for the door) 49.5 header width. Refer to Figure (8-2) for reference. Refer to Figure (8-1) for overall instructions. Step 8A: Installing Header Bar (D4) Place the Header bar (D4) at approximately 94 from the floor to the bottom of header bar (D4), and even with the top of the Posts (M2). Refer to Figure (8A-1) for reference. Attach it to the vertical post with the Hinge Door Bracket (B3) Secure with the Self Tapping Screw (F1) as shown. Refer to Figure (8A-1) for location of clips. Refer to Figure (8A-2) for assembly instructions. Step 8B: Determining the Door Hinge Direction. The included Hinge door can be attached 1 of 4 ways. See Figure (8B-1) If your door swings IN please refer to (Step 8F). If your door swings OUT please refer to (Step 8D). Fig. 8B 1 Clip Location Fig. 8A 1 Fig. 8A 2 H3 H4 96 Fig. 8 2 Swing Out Lock Left Swing Out Lock Right Swing In Lock Left Swing In Lock Right 11

12 Hinge Door Assembly Step 8C: Hinge (D2) Attachment Attach the Hinge (D2) to the end of the door opposite the lock, with the provided TEK Self Tapping Screws (F1). Make sure the bend portion of the swing faces the way you intend your door to swing. For Hinge reference use Figure (8B-1). For Attachment see Figure (8C-1). Line up the bottom and top of the hinge to the bottom and top of the door provided. Step 8D: Installing Stop Angle (D3) Swing Out option. If your Door Swings IN Lock Left or Lock Right reference (Step 8E): Installing Door. If your Door Swings OUT Lock Left or Lock Right, attach the Stop Angle (D3) to the end of the door. Attach with provided TEK Self Tapping Screws (F1). Make sure that the Rectangular Slot fits over the Lock Opening This can be done by lining up the back edge of Hinge (D2) to the Back edge of the door. As Shown in Figure (8D-1). Make sure that the top and bottom of the Stop Angle (D3) are approximately lined up with the top and bottom of the door. Step 8E: Installing Door. Attach the Door to the Hinge post (Based on the direction and lock location of your door determined in (Step 8B), Figure (8B-1)). Fasten with the provided TEK Self Tapping Screws (F7) into the pre-drilled holes; adjust for best swing. After installing the door, attach the Receiver Bar (D1) on the opposite post. (Make sure that the rectangular slot on the Receiver Bar (D1) lines up with the rectangular slot and the lock on the Door. Refer to Figure (8E-1)) Step 8F: Installing Swing In option. If your Door Swings IN Lock Left or Right Attach the Angle to the Post Opposite the Hinge Post AFTER you have Installed the Door as shown in Figure 8F-1 Attach only at the top and the bottom, DO NOT screw in all the way. Place the Receiver Bar (D1) on top of Stop Angle (D3), line up the rectangular opening with the lock on the door and a ach using provided TEK Self Tapping Screws (F1) into the pre drilled holes. Use Figures (8F 1) and (8E 1) for reference. (A er ensuring that all assembly parts fit ghten the screws). Stop Angle Fig. 8C 1 Fig. 8D 1 Exis ng Door Receiver Bar Fig. 8E 1 Fig. 8F 1 Lock Post 12

13 Slide Door Assembly DOOR POSTS 36 INSIDE OF POSTS FOR S3 48 INSIDE OF POSTS FOR S4 60 INSIDE OF POSTS FOR S5 72 INSIDE OF POSTS FOR S6 96 INSIDE OF POSTS FOR S8 13

14 Slide Door Assembly Step 9: Installing a Slide Door (Optional) Prior to beginning installation of slide door make sure that your layout includes an appropriate side slide door. Prior to beginning make sure that all the parts required for a slide door assembly are included (see below). Prior to beginning make sure that your side posts are already installed and are secure in their location. The spacing for the slide doors are as follows: S3 S4 S3 36 X 96 (From the ground to the top of the clearance for the door) S4 48 X 96 (From the ground to the top of the clearance for the door) S5 60 X 96 (From the ground to the top of the clearance for the door) S6 72 X 96 (From the ground to the top of the clearance for the door) S7 84 X 96 (From the ground to the top of the clearance for the door) S8 96 X 96 (From the ground to the top of the clearance for the door) S5 S7 96 S6 S8 Refer to Figure (9-2) for reference. Refer to Figure (9-1) for overall reference. Fig. 9 2 Step 9A: Slide Door Bracket (B4) Assembly. If your Post (M2) Height is MORE then 96 proceed to (Step 9C). Assemble Slide Door Bracket (B4) and Slide Door Mounting Strip (B5) with an (F10), (F7) and (F3) as shown in Figure (9A-1). Please note that Mounting Strip (B5) has uneven placed holes make sure to attach the Bracket (B4) to the farthest hole. Fig. 9A 1 14

15 Slide Door Assembly Step 9B: Slide Door Pre-Assembly. Attach the Guide (B8) to the bottom back end of the door with provided Carriage Bolt (F2) and Nut (F3), as shown in Figure (9B-1). Attach the Trolley assembly (B9) to the top of the door by inserting it into the existing holes at the top of the door. For reference use Figure (9B-2). Step 9C: Slide Channel Assembly & A achment. Take the slide door bracket assembly (Step 9A) and a ach it through the bo om two holes via a TEK Screw (F1) and a Washer (F4). Refer to Figure (9C 1) for visual instruc ons. Insert the Slide Door Track inside the Slide Door Bracket Assembly as shown in Figure 9D 2. Fig. 9B 1 Tighten the bolts on top of the Slide Door Bracket (B4) through the holes in the Slide Door Track (D6). Refer to Figure (9C 2) for Visual Instruc ons. (NOTE: The holes DO NOT have to be aligned, however make sure the gap between channels is minimal) If your Ver cal Post height is taller then 96 DO NOT a ach the Slide Door Bracket (B4) to the Slide Door Moun ng Strip (B5). Instead Measure 96 from the ground to the bo om of the Slide Door Bracket (B4) and using a TEK screw (F1) and (F4) washer a ach directly to post. Step 9D: Slide Door Assembly. Take the Assembled door (Step 9C) and insert the trolleys into the Slide Door Track (D6). See Figure 9D 1 for reference. Slide the door all the way through. Make sure that that door moves freely with in the Slide Door Track (D6). Make sure there is a 2 clearance between the bo om of the door and the floor. If there is not adjust the trolleys un l there is. Please note that when inser ng the door assembly the front of the door should go in first and that the lock should be facing towards the direc ons that is specified in the Plan Drawings either provided by Folding Guard or Your Company s Representa ve. A er Inser ng the Door, please insert the Stop Bolt (F12) into the free hole in the Slide Door Track Assembly on the back end of the door, and Tighten with Nut (F3). This will prevent the door from sliding out of the Slide Door Track (D6). CAUTION: Door Stop Bolt must be installed in order to prevent the door from exi ng the track. Fig. 9C 1 Fig. 9D 1 Fig. 9B 2 Fig. 9C 2 15

16 Slide Door Assembly Fig. 9E 1 Step 9E: Lock Receiver Bar (D5) Assembly. A ach the supplied Lock Receiver Bar (D5) to the post toward which the door shall close, with the provided TEK Screw (F1). See Figures (9E 1) and (9E 2) for reference. DO NOT Tighten the TEK (F1) Screws all the way. First make sure the door securely locks in the receiver bar and can be opened. A er that is complete Tighten the TEK Screws (F1) all the way. Please note that the Figure (9E 1) is the LOCKED and FINISHED condi on of the Lock Receiver Bar (D5) and the door. Step 9F: Bo om Guide (B6) Assembly. Assemble the two halves of the bo om guide (B6) by placing one half inside of the other as shown in Figure (9F 1). Secure the two halves together. If you intend to a ach the guide (B6) to the wire mesh panel (M1). Please go on the next point. If you intend to secure the Guide (B6) to the floor, secure together via floor anchors as shown in Figure (9F 2) If a aching the Bo om guide to the wire mesh assemble the two halves of the Bo om Guide (B6) and secure together with a Carriage Bolt (F2), Washer (F4) and a Nut (F3), as shown in Figure 9F 3. Fig. 9F 1 Fig. 9F 2 Fig. 9E 2 Step 9G: Bo om Guide Installa on. If a aching to the floor place the bo om guide in such a ma er that when the door is closed the Door Guide (B8) is s ll inside the Bo om Guide Bracket (B6). Make sure that the door slides easily inside the floor bracket (B6) and there is no interference. Then a ach to the floor via concrete anchors. If a aching to the wire mesh place the bo om guide in such a ma er that when the door is closed the Door Guide (B7) is s ll inside the Bo om Guide Bracket (B6). Make sure that the door slides easily inside the floor bracket (B6) and there is no interference. Then using the provided Bo om Guide A achment (B7). Secure both via provided Carriage Bolt (F2), Washer (F4) and Nut (F3), as shown in Figure (9G 1). Fig. 9G 1 Fig. 9F 3 16

17 Ceiling Kit Assembly Step 11: Ceiling Kit Assembly. Ceiling can only be installed AFTER the vertical portion of assembly has been completed per previous instructions (See Step 1) Prior to installation check Ceiling Assembly Kit for accurate part count. Step 11A: Installing Ceiling Angle (C1). Installing the ceiling angle (C1) can be accomplished either/or bend in or bend out; refer to Figure (9A-1). Attach the Angle (C1) via the provided Carriage Bolt (F2), Washer (F4), Nut (F3) and Mesh Clamp (B10) to the vertical already installed panel (M1). See Figure (11A-1) for reference. Fig. 11A 1 Lay in the Mesh Panel (M1) horizontally with legs going up, as it will serve as your Ceiling Panel. See Figure (11A-1) for reference. Attach with provided Carriage Bolt (F2), Mesh Clamp (B10), Washer (F4) and Nut (F3) as shown in Figure (11A-1). Step 11B: Ceiling Panel attachment to various verticals. When attaching to a ceiling panel to a wall, please see the (Step 2) instructions (omit the 2 sweep space note). When attaching to a roof support bracket please follow the directions in (Step 3) for attaching to a post. When attaching to another Ceiling panel please refer to (Step 5) for attaching to another panel. 17

LPR System Installation instructions

LPR System Installation instructions Toll LPR System Installation instructions 1 General Information The following installation instructions should be used as a guide for installing Folding Guard LPR System. Good common sense and appropriate

More information

WireCrafters, LLC. General Information

WireCrafters, LLC. General Information WireCrafters, LLC. General Information 6208 Strawberry Lane 502/363-6691 www.wirecrafters.com Louisville, Kentucky 40214 502/361-3857 FAX 1-800-626-1816 The following General Installation Instructions

More information

EZ-MATRIX I N S TA L L AT I O N I N S T R U C T I O N S EZ-MATRIX

EZ-MATRIX I N S TA L L AT I O N I N S T R U C T I O N S EZ-MATRIX TM I N S TA L L AT I O N I N S T R U C T I O N S READ THESE INSTRUCTIONS page 2 Installer Tips: Installation is best completed with the help of one or two people. Prior to beginning, please read through

More information

Installation Instructions

Installation Instructions Contents Page General Information and Installer Tips.......... 2 Panels & Posts............................. 3 Enclosure Description..................... 4 Hinge Door Hardware................... 4-5 Step-by-Step

More information

MATRIX GUARD. I nstallation I nstructions TERMS AND CONDITIONS. Call or visit

MATRIX GUARD. I nstallation I nstructions TERMS AND CONDITIONS. Call or visit TERMS AND CONDITIONS It is the intent of Wireway Husky Corp. that any product received by our Customers fully meets their expectations. MATRIX GUARD Wireway Husky product is Marketed and Distributed by

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Special-Lite Restroom Partitions IMPORTANT - BEFORE YOU START... 1. Read through these installation instructions first to understand the order of work. 2. Check all components

More information

96 (Standard Length)

96 (Standard Length) Setbacks 96 (Standard Length) Bike Files may be lined up end to end to fill the available space. A 36 aisle should be left between the ends of bikes in racks facing one another. 36 aisle 50 Installation

More information

Independent Containment System (ICS)

Independent Containment System (ICS) Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.

More information

Track Rack. * Track Racks are not lockable

Track Rack. * Track Racks are not lockable The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply

More information

Contour. Wall Style Adjustable Z Revised 01/30/2017

Contour. Wall Style Adjustable Z Revised 01/30/2017 Wall Style Adjustable Z000000201 Revised 01/30/2017 Page 2 of 9 Unpacking Your Shipment Unpack and iden fy each component in each box that you received. If your shipment is missing parts, or too many parts

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

BioPrism Solid Surface

BioPrism Solid Surface Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from

More information

Assembly Instructions

Assembly Instructions 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions

More information

Installation Instructions

Installation Instructions Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

Introduction. Depending on your kennel project, you may have some or all of the following hardware: Part # Description Part # Description 1468

Introduction. Depending on your kennel project, you may have some or all of the following hardware: Part # Description Part # Description 1468 Introduction Thank you very much for your investment in Mason kennels. We take great pride in providing our customers with the highest quality animal enclosures combined with an enjoyable ordering experience.

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.

More information

SINGLE TRACK BYPASS (patent pending) barn door hardware

SINGLE TRACK BYPASS (patent pending) barn door hardware SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

KIT ASSEMBLY INSTRUCTIONS

KIT ASSEMBLY INSTRUCTIONS KIT ASSEMBLY INSTRUCTIONS We have designed these instructions as a stepby step procedure to simplify the assembly process. Nevertheless, we do recommend including someone with carpentry expertise on your

More information

Before Assembling the Storage Wall

Before Assembling the Storage Wall Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251

More information

Twin-Wall Double Swinging Door Kit

Twin-Wall Double Swinging Door Kit 115021 Twin-Wall Double Swinging Kit READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable

More information

Bulkhead Model Number and

Bulkhead Model Number and Bulkhead Model Number 96141-3-01 and 96142-3-01 Installing your ProMaster bulkhead is very clear cut following these instructions. Before cutting or drilling in the floor, verify the location of you gas

More information

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit) Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips

More information

ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.

ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. VAN STORAGE SOLUTIONS FOR THE WAY YOU WORK TM INSTALLATION MANUAL BULKHEAD Model Number 96101-3-01 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING

More information

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

INSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION

INSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters

More information

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

YUKON PATIO COVER INSTALLATION INSTRUCTIONS

YUKON PATIO COVER INSTALLATION INSTRUCTIONS YUKON PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin: Consult your local building department for any required permits You may be required to obtain a building permit for this structure. Contact

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these

More information

BIKE FILE (301)

BIKE FILE   (301) B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing

More information

WG-4 Wall Guard Installation Instructions

WG-4 Wall Guard Installation Instructions WG-4 Wall Guard Installation Instructions Architectural Products Division Step 1: Determine top of wall guard and snap a chalk line 1/8 below to locate top of aluminum retainer, see fig 1. Store material

More information

Rolling Curtain door Manual

Rolling Curtain door Manual Rolling Curtain door Manual Installation Maintenance parts Model 944 PHONE 800 448 8979 FAX 800 236 8722 website www.tracrite.com EMAIL tr@tracrite.com ADDRESS 216 Wilburn Road Sun Prairie, WI 53590 This

More information

Installation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:

Installation Manual. Solid Plastic Toilet Partitions.   IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.: Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free

More information

Sliding Door Kit

Sliding Door Kit YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable

More information

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are

More information

INSTALLATION GUIDE. C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel )

INSTALLATION GUIDE. C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) INSTALLATION GUIDE C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Partition Assembly... 3-5 5-6 Phase 2 -

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

Installation Instructions

Installation Instructions Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors

More information

Locker Pedestal Installation Instructions

Locker Pedestal Installation Instructions Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

Rockwell 4-in-1 Sliding Door

Rockwell 4-in-1 Sliding Door Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1

More information

INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Soild Phenolic Series contents page 1080 DuraLineSeries...2-21 1180 DuraLineSeries...2-21 2080 DuraLineSeries Maximum Privacy...22-41 2180 DuraLineSeries Maximum Privacy...22-41

More information

M10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required

M10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5 PH Wood Screws. (30) Included - (24) Required Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,

More information

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K K9 KIT INSTALLATION INSTRUCTIONS 1998-2011 CROWN VIC KK-K9-F7-K TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric Socket Set Screwdriver Set Torx Bit

More information

PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR. & Assembly. Installation Instructions

PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR. & Assembly. Installation Instructions PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR & Assembly Installation Instructions 4884 HSD Standard Sliding Door Components Some Considerations When Choosing Your Stall System - 1

More information

TABLE OF CONTENTS REQUIRED TOOLS

TABLE OF CONTENTS REQUIRED TOOLS TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS

More information

INSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H

INSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS

More information

End of Row Doors. Revision Number 1

End of Row Doors. Revision Number 1 End of Row Doors Single Swing Door Café Style Doors Revision Number 1 Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com

More information

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

More information

TrendWall Floor-To-Ceiling Panels Installation Instruction

TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

Dublin Stalls Installation Instructions

Dublin Stalls Installation Instructions Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round

More information

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height

More information

10 x 10 Flat Top Two Tone Pergola

10 x 10 Flat Top Two Tone Pergola 0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00

More information

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions Locker Installation Instructions Thank you for selecting Extra Wide Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These

More information

Sentinel Electronic Safe Installation Guide

Sentinel Electronic Safe Installation Guide Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.

More information

Heavy-Duty Bypass Track System

Heavy-Duty Bypass Track System Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,

More information

GrowSpan Single Swinging Door Black-Out Door Kit

GrowSpan Single Swinging Door Black-Out Door Kit GrowSpan Single Swinging Door Black-Out Door Kit ATTENTION: Door kit includes materials for door only. All other components shown in the diagram above and diagrams throughout this guide are not included

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information

More information

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly

More information

Installation Instructions for. Before You Begin TOOLS REQUIRED

Installation Instructions for. Before You Begin TOOLS REQUIRED Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number

More information

MONKEY BARS OVERHEAD RACK INSTALLATION

MONKEY BARS OVERHEAD RACK INSTALLATION MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE

More information

Privacy Wall Glass Selections - Polished Edge Slider Door

Privacy Wall Glass Selections - Polished Edge Slider Door Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin

More information

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws

More information

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means

More information

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER. TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support

More information

4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS

4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS 4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.

More information

#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS

#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,

More information

Twin-Wall Double Swinging Door Kit

Twin-Wall Double Swinging Door Kit 105105 Twin-Wall Double Swinging Kit YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this

More information

Box Track INSTALLATION INSTRUCTIONS

Box Track INSTALLATION INSTRUCTIONS Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench

More information

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS K9 KIT INSTALLATION INSTRUCTIONS 2005-2011 CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS 2030 TrimLineSeries 2040 DesignerSeries IMPORTANT: Storage and Handling Information on last page. Review these instructions

More information

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT 1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

More information

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT

More information

GrowSpan Series 500 Door Kits

GrowSpan Series 500 Door Kits GrowSpan Series 500 Door Kits Double Swinging Door Finished Grade Finished Grade Diagram shows a double-swinging door centered and installed in an end wall frame. The door kit includes materials for the

More information

C-Series & S-Series Classic Frame with Transom (Single or Pair)

C-Series & S-Series Classic Frame with Transom (Single or Pair) 1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on

More information

ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS

ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS SAFETY GLASSES 7/16" WRENCH OR SOCKET STEP LADDER OF APPROPRIATE HEIGHT (2) 9/16" WRENCHES OR SOCKETS RUBBER

More information

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02 GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.

More information

MobileTrak5 Installation Instructions

MobileTrak5 Installation Instructions MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips

More information

Wallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS

Wallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note

More information

INSTALLATION GUIDE. C20-FTM STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel )

INSTALLATION GUIDE. C20-FTM STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) INSTALLATION GUIDE C20-FTM STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.1.1 Unpack components; compare with the bill

More information

IMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)

IMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions) ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions

More information

Assembly Instructions Music Library System

Assembly Instructions Music Library System Assembly Instructions Music Library System 7-Shelf Unit is shown. 6-Shelf Unit assembly is the same except where noted. Contents Important User Information...........................2 General...2 Manufacturer...2

More information

13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME

13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME 1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS ALTERNATIVE

More information

Assembly Instructions

Assembly Instructions Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel

More information

INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Plastic Laminate Series contents page 1030 TrimLineSeries...2-21 1040 DesigerSeries...2-21 Urinal Screens, Benches, Shower Seats...22-31 2030 TrimLineSeries Maximum Privacy...32-47

More information

Pharma-Slide. Installation Manual. [Revision: June 14, 2010, SL150001, Rytec Corporation 2005]

Pharma-Slide. Installation Manual. [Revision: June 14, 2010, SL150001, Rytec Corporation 2005] Pharma-Slide Installation Manual [Revision: June 14, 2010, SL150001, Rytec Corporation 2005] TABLE OF CONTENTS PAGE INTRODUCTION.............................................1 HOW TO USE MANUAL..............................................1

More information

Elite Home-Attached Greenhouse

Elite Home-Attached Greenhouse Elite Home-Attached Greenhouse Photo may show a greenhouse of a different length. Elite Home-Attached Greenhouse Use these instructions for the following greenhouses: #104711 #104713 #104715 2007 ClearSpan

More information

Spring Loaded All Season Roll-Up Doors

Spring Loaded All Season Roll-Up Doors Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information