Technical Manual Beltone Turn ITE. Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark

Transcription

1 Technical Manual Beltone Turn ITE Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Service@beltone.com

2 Table of contents Subject Page Matrix... 3 Spare Part List... 4 Faceplate Assemblies... 5 Blank Faceplates... 6 Hybrid Connections... 7 Diagram Receiver assembly Prepare the faceplate Options Final Device Service tool Test Equipment Page 2 of 17

3 Matrix C3.1 Battery Size 13 Normal Power Single Mic VC (floating) L-TRIMMER P-TRIMMER H-TRIMMER Push Button Telecoil TN45-P x x x Standard Optional Optional Optional Optional Optional TN3T45-P x x x Standard Standard Standard Standard Optional Optional Note: All ITE faceplate assemblies can be fitted with three trimmers or less. If a trimmer, PB and telecoil are opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the TURN Configuration Tool Software to reflect correct option added / removed. The Turn configuration software can be downloaded from the GTO website: Page 3 of 17

4 Spare Part list Item Part No. Tubing,Q-flex,.100 ID X.120 OD Tape, 3m., Doubleface (56X3.9MM) Wrap for BK1610 receiver Flex-Hybrid, C3.1, Denmark Microphone, EM-6717, Portless Receiver, BK Push Button Tube sleeve Sleeve, Wire Wire, ESW, Blue, 7x50µ 14 mm Wire, ESW, Blue, 7x50µ 16 mm Wire, ESW, Blue, 7x50µ 22 mm Wire, ESW, Green, 7x50µ 8 mm Wire, ESW, Green, 7x50µ 13 mm Wire, ESW, Green, 7x50µ 16 mm Wire, ESW, Green, 7x50µ 22 mm Wire, ESW, Green, 7x50µ 24 mm Wire, ESW, Green, 7x50µ 28 mm Wire, ESW, Green, 7x50µ 32 mm Wire, ESW, Red, 7x50µ 14 mm Wire, ESW, Red, 7x50µ 16 mm Wire, ESW, Red, 7x50µ 22 mm Wire, ESW, Red, 7x50µ 28 mm Wire, ESW, Red, 7x50µ 32 mm Wire, ESW, Amber, 7x50µ 10 mm Wire, ESW, Amber, 7x50µ 22 mm Wire, ESW, Amber, 7x50µ 28 mm Option Part No. Trimmer,L,150K,PJ63,Green Trimmer,H,150k,PJ63,Yellow Trimmer,P,150K,PJ63,Black Push Button Telecoil Analog VC Complete Part No. VC, ASM, L VC, ASM, R Note: For conformal coating EGC-17000, check the vendor website: to purchase locally. For conformal coating SL1367 peters coat, check the vendor website: to purchase locally. Page 4 of 17

5 Faceplate Assemblies VC, No Trimmer - Left, HP VC, 3 Trimmer - Left, HP VC, 2 Trimmer - Left, HP VC, 3 Trimmer, Telecoil - Left, HP Page 5 of 17

6 Blank faceplates 13 FLT VC - Left 13 FLT VC - Right Blank FP Single mic. Part No. FP, 13, FLT VC, Light (L) FP, 13, FLT VC, Medium (L) FP, 13, FLT VC, Dark (L) FP, 13, FLT VC, Light (R) FP, 13, FLT VC, Medium (R) FP, 13, FLT VC, Dark (R) Battery Door 13 Part No. Batt Door Left, Light Batt Door Left, Medium Batt Door Left, Dark Batt Door Right, Light Batt Door Right, Medium Batt Door Right, Dark Page 6 of 17

7 Hybrid connections (C3.1 Flex) MIC - BATT - H13 H14 H18 H19 H3 H2 MIC(0) REC + H10 H20 H9 H7 H1 MIC + REC - H11 H21 H22 H8 H4 BATT + H12 H17 H16 H15 H6 H5 NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering. MODULE MODULE Page 7 of 17

8 Diagram - ITE Left NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering. Page 8 of 17

9 Diagram - ITE Right NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering. Page 9 of 17

10 Receiver assembly BK1610 rec. wires are to be routed as shown. BK1610 rec: Place foamwrap p/n as shown. NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering. Page 10 of 17

11 Prepare the faceplate - Trimmer Installation Mark target hole. Drill target hole. Remove debris and insert trimmer, NOTE : Do the same process for additional trimmers. Let the glue cure first then operate the trimmer to ensure that it is not frozen. Drill bit or 1.93mm for the trimmer hole Make trimmer flush even on the external side of faceplate. Use Loctite 416 and glue around the trimmer (internal side). Let it cure. Page 11 of 17

12 Prepare the faceplate - PB Installation Mark and drill a pilot hole using a smaller drill bit on a manual grinder. Remove excess debris. Use TC00298 drill bit and carefully drill onto the pilot hole. Drill all the way through. Remove excess debris. Insert PB on faceplate hole thenglue round the push-button using Loctite 416 P/N Let it air dry for 5 mins Page 12 of 17

13 Prepare the faceplate - VC Installation Mark target hole. Drill target hole. Remove debris and insert Analog VC NOTE : Let the glue cure first then operate the VC to ensure that it is not frozen. Drill bit or mm for the Analog VC hole Make sure that VC is not protruding too much above the highest point of the external side of faceplate. Use Loctite 416 and glue around the VC (internal side). Let it cure. Page 13 of 17

14 Options TEL-Y10 ad 10 Pad 11 Telecoil H - TRIMMER P - TRIMMER L - TRIMMER A S E A S E A S E Push Button Note: If a trimmer, PB and telecoil are opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the Turn Configuration Tool Software to reflect correct option added / removed. The Turn Configuration Software can be downloaded from the GTO website: Page 14 of 17

15 Final Device 3 TRIMMER OPTION 2 TRIMMER OPTION Page 15 of 17

16 Service Tool The tool can be used on both sides. One side for size 13 and 312, the other side to be used for size 10 Size 13 and 312 Size 10 When working on the assembled faceplate a heat sink (p/n ) must always be used in order to prevent damages to the components. Page 16 of 17

17 Test Equipment Both programming cable sets shown on this page can be used When testing / programming a battery pill must be used: The device is to be configured with either AUDIOMaster or TURN Configuration Software for trimmers, PB and tele-coil options. The Configuration Software can be downloaded from the GTO website Connect the flex to the programming cable by using the flex end marked with an arrow. Programming cable CS63 p/n Flex strip 10 pcs. p/n Programming cable CS44 : P/n , Blue (L) P/n , Red (R) P/n , Flex adaptor CS44 (incl a flex strip) Page 17 of 17