Fixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved

Save this PDF as:

Size: px
Start display at page:

Download "Fixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved"

Transcription

1 Fixed Wall Arm Installation Guide Part number Rev E 2012 PolyVision Corporation All rights reserved

2 Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations... 4 Tools and supplies... 5 What comes in the box... 5 Required items... 6 Suggested hardware for the wall bracket... 7 Install the fixed wall arm... 8 Step 0: Install the whiteboard... 8 Step 1: Position the fixed wall arm... 8 Step 2: Locate and mark fastener locations on the wall... 9 ēno classic interactive whiteboards... 9 ēno click interactive whiteboards Step 3: Fasten the wall bracket to the wall Wood stud installation Hollow concrete/brick wall installation Solid concrete/brick wall installation Step 4: Assemble the boom arm, cover, and breakaway plate Step 5: Fasten the breakaway plate to the boom arm Step 6: Fasten the boom arm/breakaway assembly to the wall bracket Step 7: Prepare the projector adapter plate Step 8: Fasten the projector mount to the boom arm Step 9: Fasten the projector adapter plate to the projector Step 10: Fasten the projector to the boom arm Step 11: Connect cables to the projector and add the magnetic icon strip to the whiteboard Cable strain relief Step 12: Power on the projector Projector adjustment and driver installation Step 13: Troubleshooting projector focus and alignment Focus Image size Image location (left to right) Image tilt Image location (up and down) Image location (up and down) Final check Step 14: Install the PolyVision Driver Index of REV E Installation and Operation Guide

3 Important Safety Instructions Read all instructions before using the ēno one fixed wall arm. DANGER To reduce the risk of electrical shock: 1. Always unplug this mounting system from the electrical outlet before cleaning. WARNING To reduce the risk of burns, fire, electrical shock, or injury to persons: 1. Unplug from outlet before putting on or taking off parts. 2. Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. 3. Never operate this mounting system if it has a damaged cord or plug. If it is not working properly, return the mounting system to a service center for examination or repair. 4. Keep cord away from heated surfaces. 5. Never operate the mounting system with the air openings blocked. Keep air openings free of lint, hair, and the like. 6. Never drop or insert any object into any opening. 7. Do not use outdoors. 8. Route cords and cables as shown in the installation instructions. 9. To disconnect, turn all controls to the off position, then remove plug from outlet. WARNING: Risk of electric Shock Connect this mounting system to a properly grounded outlet only. See grounding instructions or building engineer to ensure proper electrical and grounding conditions for the product. WARNING: Risk of Injury to Persons Do not place video equipment such as televisions or computer monitors on the ēno one fixed wall arm. This product is designed to be used with the supplied projector only. NOTE: Save these instructions for future use. PolyVision REV E 3 of 26

4 Overview Congratulations on your purchase of the PolyVision ēno one solution. This manual describes how to install the PolyVision ēno one fixed wall arm mounting solution for the PolyVision PJ905 projector. The fixed wall arm is designed to accommodate the PolyVision PJ-905 projector only. ** DO NOT EXCEED A 15LB (7 kg) LOAD ON THE BOOM ARM TO AVOID DAMAGE ** Important considerations Measure the clearance height between the top of the ēno interactive whiteboard and the ceiling. The minimum amount of clearance needed for installation is 24 inches (61cm). The total system without projector weighs roughly 21 pounds (9 kg). Two people are recommended for portions of this installation. The maximum allowable projector weight is 15 pounds (7 kg). No unauthorized modifications or additions are to be made to the system. Do not hang from or climb on the boom arm or wall bracket. Tighten all screws securely. CAUTION FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Read the entire Assembly Direction before beginning installation or assembly. Building construction varies greatly and is outside PolyVision s control. The Building s Engineer of record is responsible for the design of studs, backing, reinforcement, supporting members etc. which the units are attached to and must verify the adequacy of the mounting hardware. These instructions and any hardware provided by PolyVision are for convenience only and are not an indication of what may be required by your local Code. The building owner or designated agent is responsible for verifying that the installation is in compliance with all local Codes and regulations. 4 of REV E Installation and Operation Guide

5 Tools and supplies What comes in the box 1 Wall bracket 2 Breakaway plate 3 Cover 4 Boom arm 5 PJ905 Projector 6 Projector mount and Projector adaptor plate 7 Wall template 8 Quick start guide 9 CD 10 USB Cable 11 Projector power cable 12 VGA cable 13 Hardware bag: Allen wrench, cable ties, 5/16-18 bolts (x2), ¼ 20 nylon insert lock nuts and washers (x2), thumb screws (x3) 14 Magnetic projector control icon strip PolyVision REV E 5 of 26

6 Required items Locate and have ready to use Power Drill and/or Hammer drill Stud finder (stud walls) 7/16 (11mm) wrench #2 Phillips screw driver Measuring tape Bubble level Step ladder Wall mounting hardware for your wall type and local code Tape (For temporarily attaching template to the wall) #2 7/16 6 of REV E Installation and Operation Guide

7 Suggested hardware for the wall bracket Note: These instructions guide you through installing the wall bracket on wall of a sheetrock, brick, or concrete. Use these instructions as a guideline but install appropriate anchors to secure the wall mounting assembly according to all local codes and protocols. Use the following hardware or equivalents for fastening the wall bracket to the wall. Follow all manufacturer requirements for hardware installation. A. If mounting to a wood stud wall: (2 x4 wood studs, 16 on center stud spacing, 5/8 max gypsum board). Qty 3: ¼ lag screw with 7/16 hex head, 2.5 long (for mounting to wood wall stud). Qty 2: ¼ - 20 Toggler Brand Toggle bolts, 2.5 long (for mounting sides of wall plate to sheetrock). Tensile Load Rating 265lbs (5/8 gypsum) per Toggle Bolt. Qty 5: ¼ ID, ½ OD fender washer. Installed between bolt head and Wall Bracket. B. If mounting to a Hollow Concrete Block Wall: (8 x8 x16 block, ASTM C90 Approved). Qty 4: ¼ - 20 Toggler brand hex head toggle bolts, 2.5 long (for mounting sides of wall plate to sheetrock). Tensile Load Rating 1080lbs in Concrete Block per Toggle Bolt. Qty 4: ¼ ID, ½ OD fender washer. Installed between bolt head and Wall Bracket. C. If mounting to a Solid Concrete Wall: (2500 psi min per ASTM C39, 3.5 thickness min). Qty 4: 1/4" Concrete wall sleeve bolt anchors, 1-3/4" long with hex head bolt. Tensile Load Rated 1500lbs in concrete. Qty 4: ¼ ID, ½ OD fender washer. Installed between bolt head and Wall Bracket. PolyVision REV E 7 of 26

8 Install the fixed wall arm Step 0: Install the whiteboard Install the ēno classic interactive whiteboard or ēno click interactive whiteboard using instructions included with those products. Ensure that an electrical outlet is available for the projector. ēno classic interactive whiteboard: Measure and ensure that there is at least 24 inches (61cm) of clearance between the ēno interactive whiteboard and the ceiling. ēno click interactive whiteboard: Ensure that there is at least 24 inches (61cm) of clearance between the existing chalk or dry erase board and the ceiling. Step 1: Position the fixed wall arm To determine the correct position for the fixed wall arm: 1. Using a tape measure, locate and mark the center of the interactive whiteboard. 2. If installing on a sheetrock wall, use a stud finder to locate and mark the position of the wall stud nearest the center mark. 8 of REV E Installation and Operation Guide

9 Step 2: Locate and mark fastener locations on the wall ēno classic interactive whiteboards Note: Use the wall template provided to assure proper location of the wall mount. Failure to do so will result in difficulty focusing and aligning the projected image. To locate and mark fastener locations on the wall: 1. Position the bottom of the wall template so it is resting on the horizontal edge of the ēno classic whiteboard trim. wall template for use with ēno classic whiteboard only 2. Align the template as close to the center of the ēno interactive whiteboard as possible and, in addition: On a wood stud wall, ensure that the center of a stud is aligned with at least one column of bolt holes on the template. Adjust the template left or right to capture a stud. On a wall with mortared bricks/blocks, ensure that the top and bottom row of bolt holes do not align with a line of mortar. 3. Tape the wall template provided to the wall. 4. Mark bolt-hole locations. 5. See pages for instructions on how to fasten the wall bracket for each wall type. PolyVision REV E 9 of 26

10 ēno click interactive whiteboards Note: To assure proper installation of the wall bracket, use the wall bracket as a template to measure the location of bolt and cable exit holes. Failure to do so will result in difficulty focusing and aligning the projected image. To locate and mark fastener locations on the wall: 1. Carefully measure and position the bottom of the wall bracket assembly so it is 6 inches (15 cm) above the ēno click interactive whiteboard. 2. Align the wall bracket assembly as close to the center of the ēno click interactive whiteboard as possible. In addition: On a wood or metal stud wall, ensure that the center of a stud is aligned with at least one column of bolt holes on the wall bracket assembly. Adjust the wall bracket assembly left or right to capture a stud. On hollow concrete or bricks wall, ensure that the top and bottom row of bolt holes on the wall bracket assembly do not sit on top of mortar joints. 3. Mark bolt-hole locations. 4. See pages for instructions on how to fasten the wall bracket for each wall type. 10 of REV E Installation and Operation Guide

11 Step 3: Fasten the wall bracket to the wall To fasten the wall bracket to the wall: 1. Position the wall bracket on the wall matching the marks on the wall with bolt-hole locations in the bracket. 2. Ensure that the wall bracket is level and oriented upwards as indicated by the stamped up arrow, as shown below. 3. Fasten the wall bracket to the wall using the instructions on pages as appropriate for your type of wall. Ensure that the wall bracket can support loads, as shown below. 300 lbs 136 kg 300 lbs 136 kg 130 lbs 59kg PolyVision REV E 11 of 26

12 Wood stud installation 1. Bolt the wall bracket assembly to the stud using three lag screws and fender washers or equivalent, as noted on page 7. Note: Ensure that a stud is captured on at least one column of bolt holes in the wall bracket assembly and the fixed wall arm is as close to the center of the whiteboard as possible. 2. Bolt either the remaining top two bolt holes or opposite corner locations of the wall bracket assembly to the sheetrock wall using two of the toggle bolts and fender washers or equivalent, as noted on page Drill 3/16 pilot holes and install the hardware selected per the hardware manufactures installation directions for a wood stud wall. WARNING: Failure to follow the manufacturer s directions for a correct installation could result in property damage or personal injury. Note: Do not install the fixed wall arm on metal stud walls. 12 of REV E Installation and Operation Guide

13 Hollow concrete/brick wall installation 1. Bolt the wall bracket assembly to the wall on the four corner bolt locations using four of the toggle bolts and fender washers or equivalent, as noted on page 7. Note: Ensure that the top and bottom row of bolt holes on the wall bracket assembly do not sit on top of mortar joints. Adjust the bracket left or right to ensure that the toggle bolts do not enter mortar joints and the fixed wall arm is as close to the center of the whiteboard as possible. 2. Drill pilot holes and install the hardware selected per the hardware manufactures installation directions for a hollow concrete/brick wall. WARNING: Failure to follow the manufacturer s directions for a correct installation could result in property damage or personal injury. PolyVision REV E 13 of 26

14 Solid concrete/brick wall installation 1. Bolt the wall bracket assembly to the wall at the 4 corner bolt locations using four of the concrete wall anchors and fender washers or equivalent, as noted on page Drill pilot holes and install the hardware selected per the hardware manufactures installation directions for a solid concrete/brick wall. WARNING: Failure to follow the manufacturer s directions for a correct installation could result in property damage or personal injury. Step 4: Assemble the boom arm, cover, and breakaway plate To assemble the boom arm, cover, and breakaway plate: 1. Slide the cover onto the boom arm. Ensure that the front of the cover (noted by the PolyVision logo) is facing towards the front foot of the boom as shown below. 14 of REV E Installation and Operation Guide

15 2. Slide the breakaway plate onto the end of the boom arm and route the projector VGA, Power, USB cables (provided with the projector) through the boom arm and breakaway plate as shown below. Step 5: Fasten the breakaway plate to the boom arm Caution: Two alternative locations are provided for fastening the boom arm to the breakaway plate. Assure the proper positioning of the boom arm based on whether you are installing with the ēno classic or ēno click interactive whiteboard. Failure to do so will result in difficulty focusing and aligning the projected image. To fasten the breakaway plate to the boom arm: 1. ēno classic interactive whiteboard: Align the boom arm screw hole with the front screw hole location on the breakaway plate. ēno click interactive whiteboard: Align the boom arm screw hole with the rear screw hole location on the breakaway plate. click PolyVision REV E 15 of 26

16 2. Fasten the breakaway plate to the boom arm using one 5/16-18 bolts provided in the hardware bag. NOTE: The screw should align with the hole in the boom arm and the breakaway plate, and easily fit in the pre-drilled holes. Step 6: Fasten the boom arm/breakaway assembly to the wall bracket To fasten the boom arm/breakaway assembly to the wall bracket: 1. Slide the bottom keyed section of the breakaway plate into the rectangular flange wall of the wall bracket. 2. Bolt the breakaway plate to the wall bracket using two ¼ 20 nylon insert lock nuts and two washers provided in the hardware bag. Step 7: Prepare the projector adapter plate Disassemble the projector adapter plate from the projector mount by removing the two thumbscrews as shown below. NOTE: Retain the thumbscrews for use in step of REV E Installation and Operation Guide

17 Step 8: Fasten the projector mount to the boom arm To fasten the projector mount to the boom arm: 1. Slide the the projector mount onto the boom arm. 2. Align the projector mount so that the bolt is centered in the adjustment slot as shown below. 3. Fasten the projector mount to the boom arm using the 5/6-18 bolt provided in the hardware bag. PolyVision REV E 17 of 26

18 Step 9: Fasten the projector adapter plate to the projector To fasten the projector adapter plate to the projector: 1. Align the three screw holes on the projector adapter plate with the hole locations on the projector as shown below. 2. Fasten the plate to the projector using three thumb screws provided in hardware bag. Two of the screw holes in the projector adapter plate are elongated slots. Assure that the screws are centered in the elongated slots. 18 of REV E Installation and Operation Guide

19 Step 10: Fasten the projector to the boom arm To fasten the projector to the boom arm: 1. Align the front folded edge of the projector adapter plate with the front keyed section of the projector mount and suspend the projector from the boom arm. 2. Rotate the projector up and into place. 3. Align the screw holes in the projector plate with those on the mount assembly. 4. Fasten the projector in place using the two thumb screws that were removed in step 7. PolyVision REV E 19 of 26

20 Step 11: Connect cables to the projector and add the magnetic icon strip to the whiteboard 1. Connect the power, USB and VGA cable to the back of the projector as shown below. 2. Affix the magnetic icon strip for projector control to the whiteboard. 3. Remove lens cover from the projector. Cable strain relief For strain relief when cables are routed outside the wall, cable tie locations are provided at the center top and bottom of the wall bracket. To add cable ties: 1. Locate one cable tie provided in the hardware bag. 2. Loop the cable tie through the cable tie location provided on the wall bracket. 3. Ensure that a 1 (25mm) loop of excess cable is left for clearance. 20 of REV E Installation and Operation Guide

21 4. Secure the cables to the wall bracket. 5. Slide the cover down the boom arm and snap it onto the wall bracket. Ensure that the PolyVision logo is properly oriented as shown below. Step 12: Power on the projector Connect the projector power cord to an AC outlet and press the power button on the projector. PolyVision REV E 21 of 26

22 Projector adjustment and driver installation Step 13: Troubleshooting projector focus and alignment Once the projector is powered on and warmed up, a PolyVision splash screen appears automatically on the ēno interactive whiteboard. The following steps describe how to adjust the focus and position of the splash screen if necessary. Focus To adjust the splash screen focus: 1. Use the manual focus adjustment found on the front of the projector. FOCUS Image size To adjust the splash screen size: 1. Loosen the projector mount 5/6-18 bolt (see step 7). 2. Slide the projector front or back to increase or decrease the splash screen size. 3. Tighten the 5/6-18 bolt. 22 of REV E Installation and Operation Guide

23 Image location (left to right) To adjust the splash screen location from left to right: 1. Loosen the two exposed projector adaptor plate thumbscrews (see Step 9). 2. Rotate the projector to move the splash screen image. 3. Tighten the thumbscrews. Image tilt To adjust the tilt angle of the splash screen: 1. Adjust the jack screws on top of the projector mount. Tighten or loosen one jack screw at a time for best results. PolyVision REV E 23 of 26

24 Image location (up and down) To adjust the splash screen location up and down: 1. Adjust the jack screws on top of the projector mount at the same time in the same direction. Image location (up and down) Use the 7/16 (11mm) wrench to adjust the nylon nuts used to mount the breakaway plate (see step 6) as follows: To move the splash screen down: 1. Loosen the front nylon nuts (turn both left and right nuts counterclockwise). 2. Lower the projector boom arm downwards. Make sure that both nuts have been adjusted the same amount and the boom arm is perpendicular to the wall. 3. Tighten the back nylon nuts (counterclockwise) to capture the breakaway plate location. To move the splash screen up: 1. Loosen the back nylon nuts (turn both left and right nuts clockwise). 2. Raise the projector boom arm upwards. 3. Ensure that both nuts have been adjusted the same and the boom arm is perpendicular to the wall. 4. Tighten the front nylon nuts (clockwise) to capture the breakaway plate location. 24 of REV E Installation and Operation Guide

25 Final check Once all adjustments have been made to the splash screen location, go back through the assembly and ensure that all hardware has been fully tightened. Step 14: Install the PolyVision Driver To get started using the PolyVision ēno one fixed wall arm mounting solution for the PolyVision PJ905 projector: 1. Install the PolyVision driver 2.2 (or newer) on the teacher s computer. 2. Check the Projector Control Application box during PolyVision driver installation to enable the magnetic icon strip to control the projector. 3. Connect the USB and VGA cables to the teacher s computer. Proceed with the instructions that are provided with the ēno interactive whiteboard to prepare the ēno stylus for use. PolyVision REV E 25 of 26

26 Index Boom arm, 5, 14, 15 Boom arm/breakaway assembly, 16 Breakaway plate, 5, 14, 15 Cable strain relief, 20 Cable tie, 20 Clearance, 8 Clearance height, 4 Connect cables, 20 Correct position, 8 Cover, 5, 14, 21 ēno classic, 8 ēno click, 8, 10 Fastener locations, 9 Final check, 25 Focus, 22 Hollow concrete/brick wall installation, 13 Icon strip, 5, 20 enabling, 25 Image location (left to right), 23 Image location (up and down), 24 Image size, 22 Image tilt, 23 Maximum allowable projector weight, 4 Metal stud installation, 12 PJ-905 Projector, 4, 5 PolyVision driver 2.2, 25 Power button, 21 Projector adapter plate, 16, 18, 19 Projector adaptor plate, 5 Projector adjustment, 22 Projector mount, 5, 16, 17 Required items, 6 Solid concrete/brick wall installation, 14 Suggested hardware, 7 Troubleshooting, 22 Wall bracket, 5, 11 Wall template, 5, 9 What comes in the box, 5 Wood stud installation, 12 Wood stud wall, 7 26 of REV E Installation and Operation Guide

ēno one Adjustable Wall Mount and Adjustable Mobile Stand Installation Guide

ēno one Adjustable Wall Mount and Adjustable Mobile Stand Installation Guide Installation Guide Part number 2002105-001 Rev B 2011 PolyVision Corporation All rights reserved Table of contents Overview... 3 Important considerations... 3 Adjustable Wall Mount considerations... 3

More information

Adjustable Wall Mount and Adjustable Mobile Stand for the PolyVision PJ920 Ultra-Short Throw Projector. Installation Guide

Adjustable Wall Mount and Adjustable Mobile Stand for the PolyVision PJ920 Ultra-Short Throw Projector. Installation Guide Adjustable Wall Mount and Adjustable Mobile Stand for the PolyVision PJ920 Ultra-Short Throw Projector Installation Guide Part number 2002553-001 Rev A 2011 PolyVision Corporation All rights reserved Table

More information

Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays

Installation and Assembly: Flat Video Wall Mount For 40 to 65 Flat Panel Displays Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read

More information

SB-WM-ART2-L-BL SB-WM-ART2-XL-BL

SB-WM-ART2-L-BL SB-WM-ART2-XL-BL SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier

More information

SB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL

SB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum

More information

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image

Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image UX60-RFK-685 Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image Follow these instructions to install brackets on your SMART Board 685ix

More information

INSTALLATION MANUAL PBL-UMP

INSTALLATION MANUAL PBL-UMP INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...

More information

Installation and Assembly: Full Service Video Wall Mount

Installation and Assembly: Full Service Video Wall Mount Installation and Assembly: Full Service Video Wall Mount Model: DS-VW765-LAND Max UL Load Capacity: 125 lb (57 kg) 1 of 12 ISSUED: 05-13-11 SHEET #: 145-9011-5 05-21-12 Note: Read entire instruction sheet

More information

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

INSTALLATION MANUAL PBC-UMS

INSTALLATION MANUAL PBC-UMS INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation

More information

MPA-9000 Universal Ceiling Projector Mount Kit

MPA-9000 Universal Ceiling Projector Mount Kit I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small

More information

Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays

Installation and Assembly: Articulating Swivel Arm for 37 - 60 Flat Panel Displays Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502

More information

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description

More information

Dual Arm Tilt LCD Mount

Dual Arm Tilt LCD Mount Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,

More information

SM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL

SM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL SM-RAZOR-F-M/L/XL Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

Assembly Instructions for model: VMPR1

Assembly Instructions for model: VMPR1 Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET

More information

Small Above Fireplace Pull-Down Full-Motion TV Wall Mount

Small Above Fireplace Pull-Down Full-Motion TV Wall Mount Small Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 33123 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...

More information

Installing flat panels on the MPL15 wall mount

Installing flat panels on the MPL15 wall mount Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape

More information

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3

More information

Installation Instruction

Installation Instruction Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry

More information

Installation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens

Installation and Assembly - Articulating Swivel Double-Arm for 42 - 71 Plasma Screens Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum

More information

Model : TLX-350FM. TV Mount Installation Guide

Model : TLX-350FM. TV Mount Installation Guide Model : TLX-350FM TV Mount Installation Guide Thank you for choosing Stanley the hardware of choice for Architects, Contractors, and Home Owners for its quality, performance and dependability. Following

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

Installation Guide Guide d installation

Installation Guide Guide d installation Installation Guide Guide d installation Safety Instructions For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that ignores instructions in this guide

More information

Assembly Instructions for Model: VMPL3

Assembly Instructions for Model: VMPL3 Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will

More information

Installation and Assembly: Wallmount for CPA100 and Whiteboard

Installation and Assembly: Wallmount for CPA100 and Whiteboard Installation and ssembly: Wallmount for CP100 and Whiteboard Model: 100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 Visit 3215 the

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Displays Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product

More information

Tilting, Swiveling & Rotating Flat Panel Wall Mount

Tilting, Swiveling & Rotating Flat Panel Wall Mount Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical

More information

LCD DISPLAY MOUNT

LCD DISPLAY MOUNT I N S T A L L A T I O N M A N U A L 38-804769-01 LCD DISPLAY MOUNT WWW.CHRISTIEDIGITAL.COM Contents - Assembly drawing - Securing the bottom wall plate - Fine tune adjustments - Marking the top plate mounting

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Screens Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S

More information

Yes 20 Charging Wall Cabinet for Tablets

Yes 20 Charging Wall Cabinet for Tablets Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.

More information

Tilting Flat Panel Wall Mount Installation Guide

Tilting Flat Panel Wall Mount Installation Guide Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees

More information

ELPMB27. Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs)

ELPMB27. Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs) ELPMB27 Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs) Safety Instructions Before using the wall mount, make sure you read all of the safety instructions

More information

Full-motion Wall Mount

Full-motion Wall Mount Full-motion Wall Mount MD120409-01 AWM1521- AU Safety Instruction Component Checklist WARNING IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing.

More information

Universal Projector Ceiling Mount Model: DPM-45

Universal Projector Ceiling Mount Model: DPM-45 Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this

More information

INSTALLATION MANUAL ELPMBUNI

INSTALLATION MANUAL ELPMBUNI INSTALLATION MANUAL ELPMBUNI Warning Statements WARNING: WARNING: WARNING: WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN

More information

PAM-200 Universal Projector Mount

PAM-200 Universal Projector Mount INSTALLATION MANUAL PAM-200 Universal Projector Mount Sony Electronics 16540 West Bernardo Drive San Diego, CA 92127 www.sony.com IN-PAM200.R0 Table of Contents Parts List...- 3 - Installation Tools...-

More information

MM750 Installation Instructions

MM750 Installation Instructions MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on

More information

Installation Instructions

Installation Instructions READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes

More information

LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns

LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32 with up to 200mm x 200mm VESA Mounting Patterns Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60

More information

Model MSPPWRTW Large Flat Panel Single Arm Wall Mount

Model MSPPWRTW Large Flat Panel Single Arm Wall Mount INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface

More information

19 to 39 TV WALL MOUNT - FULL MOTION

19 to 39 TV WALL MOUNT - FULL MOTION 19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5

More information

Medium Flat Panel Dual Swing Arm Wall Mount JWD-V

Medium Flat Panel Dual Swing Arm Wall Mount JWD-V INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending

More information

INSTALLATION INSTRUCTIONS. Large Flat Panel Wall Mount Model: PRO-2000 Series

INSTALLATION INSTRUCTIONS. Large Flat Panel Wall Mount Model: PRO-2000 Series INSTALLATION INSTRUCTIONS Large Flat Panel Wall Mount Model: PRO-2000 Series PRO-2000 Series Wall Mount Features: Accommodates large flat screens weighing up to 200 lbs (90.7 kg). Mounting brackets adapt

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

QLF215 INSTRUCTION MANUAL

QLF215 INSTRUCTION MANUAL QLF215 INSTRUCTION MANUAL We ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We re ready to help! 1 2 3 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

More information

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation

More information

Installation and Assembly: Universal Projector Wall Arm

Installation and Assembly: Universal Projector Wall Arm Installation and ssembly: Universal Projector Wall rm Models: PST-2955, PST-2955-W, PST-2955, PST-2955-W Max UL Load Capacity: 35 lb (5.8 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-22 Fax: (800)

More information

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with

More information

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option

More information

MSP-DCCPGTU Large Screen Tilt Display Mount

MSP-DCCPGTU Large Screen Tilt Display Mount INSTALLATION INSTRUCTIONS Large Screen Tilt Display Mount The Large Screen Tilt Display Mount is a quick disconnect mounting solution for large flat panel displays. The mount features infinite adjust ability

More information

INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1

INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount

More information

INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111

INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.

More information

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option

More information

Models: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens

Models: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 95 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens Models: PLAV70-UNL, PLAV70-UNLP Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle Aurora, Il 60502

More information

Elo Touch Solutions Wallmounting Kit for the 7001L IDS Touchmonitors

Elo Touch Solutions Wallmounting Kit for the 7001L IDS Touchmonitors Installation Manual Elo Touch Solutions Wallmounting Kit for the 7001L IDS Touchmonitors SW602083 Rev E Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Video Wall Installation Instructions 2W X 3H, 3W X 3H

Video Wall Installation Instructions 2W X 3H, 3W X 3H Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

PART #MSP-DCCST Flat Panel Tilt Mount

PART #MSP-DCCST Flat Panel Tilt Mount INSTALLATION INSTRUCTIONS PART # Flat Panel Tilt Mount The Flat Panel Tilt Mount is a quick disconnect mounting solution for flat panel displays. The mount features adjustability between 0 and 15 degrees

More information

TV WALL MOUNT ASSEMBLY GUIDE RF-TVMLPT01V2

TV WALL MOUNT ASSEMBLY GUIDE RF-TVMLPT01V2 TV WALL MOUNT RF-TVMLPT01V2 For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...4 ASSEMBLY GUIDE Before

More information

Model POA-CHB-XL50. Assembly and Installation Manual. Projector Bracket. Contents. Be sure to consult with a qualified installation specialist

Model POA-CHB-XL50. Assembly and Installation Manual. Projector Bracket. Contents. Be sure to consult with a qualified installation specialist Assembly and Installation Manual Projector Bracket Model POA-CHB-XL50 Be sure to consult with a qualified installation specialist This bracket is specifically for use with our projector. Be especially

More information

e997 Articulating Wall Arm MANUAL IM004-03

e997 Articulating Wall Arm MANUAL IM004-03 e997 Articulating Wall Arm MANUAL 10.18.16 IM004-03 0 WELCOME The Enovate Medical e997 Articulating Wall Arm was designed to set a new standard in quality. Enovate Medical s goal is to provide a wall arm

More information

MONOPRICE. Above Fireplace Pull-Down Full-Motion TV Wall Mount. User's Manual P/N 27773

MONOPRICE. Above Fireplace Pull-Down Full-Motion TV Wall Mount. User's Manual P/N 27773 MONOPRICE Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 27773 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...

More information

Full Motion Gas Spring TV Wall Mount - 24" to 55" Installation Instructions

Full Motion Gas Spring TV Wall Mount - 24 to 55 Installation Instructions Full Motion Gas Spring TV Wall Mount - 24" to 55" Installation Instructions 04-1102A Caution Prior to installation of this product, the installation instructions should be read and completely understood.

More information

MANUAL e130. Wallstation

MANUAL e130. Wallstation MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,

More information

Preference Collection and Treatment Console INSTALLATION GUIDE

Preference Collection and Treatment Console INSTALLATION GUIDE Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

RESIDENTIAL MOTORIZED STORAGE UNIT

RESIDENTIAL MOTORIZED STORAGE UNIT BY V-BRO PRODUCTS RESIDENTIAL MOTORIZED STORAGE UNIT Model: GGR220 INSTALLATION AND OPERATING INSTRUCTIONS Distributed Exclusively by V-BRO PRODUCTS For technical questions and replacement parts, please

More information

LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns

LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32 with up to 200mm x 200mm VESA Mounting Patterns LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns Multi-position triple pivoting arms allows you to position the monitor

More information

Full-Motion TV Mount - 47" to 90" Installation Guide

Full-Motion TV Mount - 47 to 90 Installation Guide Full-Motion TV Mount - 47" to 90" Installation Guide Full-motion Articulating LCD/Plasma TV Wall-mount TV size: 47" - 90" Tilt angle: +/- 12 degrees Max load capacity: 200 lbs / 90 kg Wall distance (at

More information

Assembly Instructions for Model: VMPR1

Assembly Instructions for Model: VMPR1 Assembly Instructions for Model: VMPR1 Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LC/LP

More information

MSP-DCCLFSD LCD Flat Screen Swing-Down Mount

MSP-DCCLFSD LCD Flat Screen Swing-Down Mount INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile

More information

MEDIUM FLAT PANEL DISPLAY TILT MOUNT MSP-MT (MTR-V)

MEDIUM FLAT PANEL DISPLAY TILT MOUNT MSP-MT (MTR-V) INSTALLATION INSTRUCTIONS MEDIUM FLAT PANEL DISPLAY TILT MOUNT (MTR-V) The tilt mount accommodates medium flat panel displays weighing up to 100 lbs (45.36kgs). The teardrop holes in the mount allow for

More information

Universal flat-panel mount

Universal flat-panel mount R I N S T A L L A T I O N M A N U A L Universal flat-panel mount LISTED E176225 3130 E. Miraloma Ave. Anaheim, CA 92806 Phone: 800 368-9700 Fax: 800 832-4888 www.mounts.com PREMIER MOUNTS 2004/ REV 00

More information

Yes 20 Charging Wall Cabinet for Tablets

Yes 20 Charging Wall Cabinet for Tablets Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 Front of Cabinet (closed) 1. Locking front door to User area. 2.

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

USE AND CARE GUIDE FIXED LED / LCD TV WALL MOUNT (UNIVERSAL MOUNTING PATTERN, FITS VESA

USE AND CARE GUIDE FIXED LED / LCD TV WALL MOUNT (UNIVERSAL MOUNTING PATTERN, FITS VESA Item #302-080 Model #50710 USE ND CRE GUIDE FIXED LED / LCD TV WLL MOUNT (UNIVERSL MOUNTING PTTERN, FITS VES 100/200/300/400/600) Questions, problems, missing parts? Before returning to the store, call

More information

Planar FWMG-MXL INSTALLATION INSTRUCTIONS

Planar FWMG-MXL INSTALLATION INSTRUCTIONS Planar FWMG-MXL INSTALLATION INSTRUCTIONS Fixed Wall Mount for Ultra Large Displays 50-98 weighing less than 300 lbs. Part Number: 955-0217-00 Planar, A Leyard 1195 NW Compton Drive Beaverton, OR 97006

More information

Installation Instructions

Installation Instructions Installation Instructions Ceiling Mount Bracket for DLP Based Projectors (for High Ceilings) Model No. ET-PKD100H Contents Important Safety Notice.................. 2 For DLP Based Projector: PT-D10000

More information

Page 1 of 6 Systems Inc.

Page 1 of 6 Systems Inc. Page 1 of 6 This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions

More information

INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320

INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320 INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15

More information

MSP-DCCPGSU Large Screen Static Display Mount

MSP-DCCPGSU Large Screen Static Display Mount INSTALLATION INSTRUCTIONS Large Screen Static Display Mount The Large Screen Static Display Mount () is a quick disconnect mounting solution for large flat panel displays. The mount self-adjusts for the

More information

A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE

A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE A-dec 574L Dental Light Mounted on an A-dec Inspire TM 59 Central Console Before You Begin. Turn off the power to the system before

More information

Wall mounting bracket

Wall mounting bracket Install Manual Wall mounting bracket Please read this manual carefully before operating your set and retain it for future reference. OSW200 P/NO : MFL63640578 (1502-REV01) www.lg.com COMPONENT Install

More information

Installation Guide. English. English

Installation Guide. English. English Installation Guide Safety Instructions For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that ignores instructions in this guide could damage the

More information

GE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -

GE Monogram. Installation. Instructions. 36 Vent Hood. Model ZV750. Call anywhere in the US and Canada - at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:

More information

Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400

Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400 Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)

More information