Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays

Size: px
Start display at page:

Download "Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays"

Transcription

1 Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il (800) Fax: (800) ISSUED: SHEET #:

2 Note: Read entire instruction sheet before you start installation and assembly. Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at , for all international customers, please contact your local distributor. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum Load Capacity. See page one. If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud fi nder is highly recommended. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. This product was designed to be installed on the following wall construction only; WALL CONSTRUCTION HARDWARE REQUIRED Wood Stud Included Wood Beam Included Solid Concrete Included Cinder Block Included Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit (not evaluated by UL) Brick Contact Qualifi ed Professional (not evaluated by UL) Other or unsure? Contact Qualifi ed Professional Tools Needed for Assembly stud fi nder ("edge to edge" stud fi nder is recommended) drill 3/16" (5mm) drill bit for wood studs 3/8" (10mm) masonry drill bit for concrete 7/16" socket wrench with extension (recommended) level phillips screwdriver Table of Contents WARNING Accessories External Wall Plate (WSP716, WSP716-S, WSP724, WSP724-S) (Metal Stud not evaluated by UL) Parts List... 3, 4 Installation to Double Wood Stud Wall...5 Installation to Solid Concrete or Cinder Block of 10 ISSUED: SHEET #:

3 Before you start make sure all parts listed are included with your product. Parts List PLA60 PLA60-S PLAV60 PLAV60-S Description Qty. Part # Part # Part # Part # A wall plate B tilt-roll assembly C arm assembly D wall support arm axle E vinyl trim F M10 x 1.5 x 15 mm screw bolt G.505 x.75 x.062" nylon washer H tilt adjustment knob I carriage bolt 3/8"-16 x 3.25" J x 2 x.062" delrin washer K #8-32 x.375" socket head cap screw L plastic finishing cap M holding pin N retainer plug O 5/16 x 3" wood screw P.250 x 1 x.068" washer Q 9/64" allen wrench R cable management clips S cable tie T 36" polyester mesh sleeve U 6 mm allen wrench V 10 mm allen wrench 1 n/a n/a W concrete anchor Some parts may appear slightly different than illustrated. A B C D E F G K L M H I J N O P Q R S U V W T 3 of 10 ISSUED: SHEET #:

4 Installation to Wood Stud Wall WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal studs (contact customer care). Metal stud installation is not UL evaluated. Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud fi nder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL). Never exceed the Maximum UL Load Capacity of 175 lb (79 kg). 1 Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud fi nder to locate the edges of the studs. Use of an edge-to-edge stud fi nder is highly recommended. Based on their edges, draw a vertical line down each stud s center. Place wall plate on wall as a template. The top mounting slots should be located.36" above the desired screen center for PLA60 and PLA60-S and.43" below the desired screen center for PLAV60 and PLAV60-S. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it using eight 5/16 x 3" wood screws (O) and washers (P). Skip to step 2 on page 6. WARNING Never mount this product to metal studs without the required accessory. O P A 4 of 10 ISSUED: SHEET #:

5 Installation to Solid Concrete or Cinder Block Wall WARNING When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifi cations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 1 Use wall plate (A), making sure that it is level, as a template to mark holes. The top mounting slots should be located at your desired display center. Use the masonry bit to drill 3/8" (10mm) dia. holes to a minimum depth of 3" (76mm). Insert anchors (W) in holes fl ush with wall as shown (right). Place wall plate (A) over anchors (W) and secure with 5/16 x 3" wood screws (O) and washers (P). WARNING Tighten screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Always attach concrete expansion anchors directly to load-bearing concrete. Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other fi nishing material. If mounting to concrete surfaces covered with a fi nishing surface is unavoidable (not evaluated by UL), the fi nishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16mm), custom fasteners must be supplied by installer (not evaluated by UL). P 1 Drill holes and insert anchors (W). 2 3 W Place plate (A) over anchors (W) and secure with screws (O). Tighten all fasteners. W O A concrete surface W INCORRECT CORRECT CUTAWAY VIEW wall plate plaster/ dry wall concrete wall plate plaster/ dry wall concrete O A 5 of 10 ISSUED: SHEET #:

6 WARNING If you are uncertain that product is properly installed, call customer care Note: There are five mounting positions. The center position is shown (right). Slide washer (J) over wall support arm axle (D). Next, insert plastic cap (N) into axle. Then, insert holding pin (M) into axle. See detail 1. Place arm assembly (C) with washer (J) into wall plate (A). Insert axle assembly shown in detail 1 through wall plate (A), arm assembly (C), and washer (J). Lock axle in place by aligning holding pin (M) with notches shown in detail 2. A M N J D DETAIL Insert socket cap screw (K) into hole at bottom of wall support arm axle (D) as shown in detail 3. Tighten screw using 9/64" allen wrench (Q). Note: Fit of axle (D) into wall plate (A) and arm assembly (C) will be tight. Gently tap into place with a hammer if necessary. C J NOTCH DETAIL 2 K D DETAIL Snap four cable management clips (R) into top or bottom of arm assembly (C) as shown. Cable ties (S) are used with clips for cord management. Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables. R T S C 6 of 10 ISSUED: SHEET #:

7 4 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). 4-1 Insert one fi nishing cap (L) into each unused hole of wall plate (A). L A SWIVEL BOX C E Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is not used with this product. 5 Insert and tape carriage bolt (I) into top hole of pitch-roll assembly (B). Attach tilt-roll assembly to adapter bracket with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U). Note: Adapter bracket (not UL evaluated, sold separately) will vary in size and style. CAUTION Do not overtighten screws! Overtightening may hinder roll option. GENERIC ADAPTER BRACKET B I F 7 of 10 ISSUED: SHEET #:

8 WARNING Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. 6 Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX C.25" F Hook tilt-roll assembly (B) onto M10 screws (F). Insert carriage bolt (I) into slot of swivel box as shown in fi gure 6.1. Install nylon washer (G) and tilt adjustment knob (H). Install remaining two M10 screws (F) as shown in fi gure 6.2. HAND TIGHTEN all four M10 screws to allow for tilt adjustment. Remove tape from carriage bolt (I). For tilt adjustment, push back on the top of plasma to relieve pressure on knob. Adjust tilt to desired position and tighten tilt adjustment knob (H), then securely tighten all four M10 screws (F) using 6 mm allen wrench (U). SWIVEL BOX I G H CAUTION After tilt is adjusted, all fasteners must be tightened. Failure to do so will result in damage to the mount. I H B F F fig. 6.1 fig. 6.2 Adapter bracket not shown for clarity. Adapter bracket not shown for clarity. 8 of 10 ISSUED: SHEET #:

9 7 Depending on the specifi c size & weight of the plasma, articulating swing arm may be angled at different 7-1 positions, causing plasma to appear to lean sideways at different articulating positions. Tilt-roll assembly (B) allows plasma to be manually adjusted, so plasma can be horizontal at all positions. To adjust, gently rotate plasma by hand to desired position. If it is too diffi cult to adjust roll of plasma, loosen screws shown in fi gure 7.1 using a phillips screwdriver. IMPORTANT! Do not loosen or tighten screws more than 1/8 turn. ARTICULATING ARM PLASMA 8 FOR PLAV 60 ONLY: Position of screen may be adjusted vertically up to.79" in each direction by doing the following: To lower screen, turn socket screw shown in figure 8.1 clockwise with 10 mm allen wrench (V). To raise screen, turn socket screw shown in fi gure 8.1 counterclockwise with 10 mm allen wrench (V). ROLL ADJUSTMENT SCREWS fig. 7.1 SOCKET SCREW fig of 10 ISSUED: SHEET #: , Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.

10 LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. ( Peerless ) warrants to original end-users of Peerless products will be free from defects in material and workmanship, under normal use, for a period of fi ve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product s manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty. In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless, (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless instructions or warnings when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure. In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured by a security device which may be included with the Peerless product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless product. This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state Peerless Industries, Inc. 10 of 10 ISSUED: SHEET #:

Models: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens

Models: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 95 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens Models: PLAV70-UNL, PLAV70-UNLP Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle Aurora, Il 60502

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 65" Plasma Screens. Models: PLAV70, PLAV70-S

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 65 Plasma Screens. Models: PLAV70, PLAV70-S Installation and ssembly - Universal rticulating Swivel Double-rm for 42" - 65" Plasma Screens Models: PLV70, PLV70-S Max UL Load apacity: 200 lb (91 kg) 2300 White Oak ircle urora, Il 60502 (800) 865-2112

More information

Installation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens

Installation and Assembly - Articulating Swivel Double-Arm for 42 - 71 Plasma Screens Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum

More information

Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box

Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box Models: IBA3, IBA3-W 2300 White Oak Circle Aurora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com

More information

Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box

Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box Models: IBA2AC, IBA2AC-W 2300 White Oak Circle Aurora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com

More information

Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays

Installation and Assembly: Flat Video Wall Mount For 40 to 65 Flat Panel Displays Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read

More information

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Displays Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product

More information

Installation and Assembly: Full Service Video Wall Mount

Installation and Assembly: Full Service Video Wall Mount Installation and Assembly: Full Service Video Wall Mount Model: DS-VW765-LAND Max UL Load Capacity: 125 lb (57 kg) 1 of 12 ISSUED: 05-13-11 SHEET #: 145-9011-5 05-21-12 Note: Read entire instruction sheet

More information

Installation and Assembly:

Installation and Assembly: Installation and ssembly: Model: DS508 os pd For SHPD installations, please contact Peerless Customer Service for a copy of the P. Maximum Load Capacity: 200 lb (90.7 kg) 2300 White ak Circle urora, IL

More information

Installation & Assembly: Two Piece Suspended Ceiling Plate

Installation & Assembly: Two Piece Suspended Ceiling Plate Installation & ssembly: Two Piece Suspended Ceiling Plate Model: CMJ453 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112

More information

Installation & Assembly: Suspended Ceiling Kit

Installation & Assembly: Suspended Ceiling Kit Installation & ssembly: Suspended Ceiling Kit Model: CMJ450 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500

More information

Installation and Assembly: Ceiling mount for LCD screens up to 29"

Installation and Assembly: Ceiling mount for LCD screens up to 29 Installation and Assembly: eiling mount for L screens up to 29" Models: L18-, L18-S, L36-, L36-S Features: omes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48" -5 to +20 adjustable

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Screens Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S

More information

Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400

Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400 Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)

More information

Installation and Assembly: Wallmount for CPA100 and Whiteboard

Installation and Assembly: Wallmount for CPA100 and Whiteboard Installation and ssembly: Wallmount for CP100 and Whiteboard Model: 100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 Visit 3215 the

More information

Installation and Assembly: Adjustable Suspended Ceiling Channel Kit

Installation and Assembly: Adjustable Suspended Ceiling Channel Kit Installation and ssembly: djustable Suspended Ceiling Channel Kit Model: CMJ500R1 C U L US This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity:

More information

Installation and Assembly: Projector Ceiling/Wall Mount

Installation and Assembly: Projector Ceiling/Wall Mount Installation and ssembly: Projector Ceiling/Wall Mount Models:PRG-EX, PRG-EX-S, PRG-EX-W PRG-EXB, PRG-EXB-S, PRG-EXB-W PRG-EXC, PRG-EXC-S, PRG-EXC-W R This product is intended for use with UL Listed products

More information

Installation and Assembly: Universal Projector Wall Arm

Installation and Assembly: Universal Projector Wall Arm Installation and ssembly: Universal Projector Wall rm Models: PST-2955, PST-2955-W, PST-2955, PST-2955-W Max UL Load Capacity: 35 lb (5.8 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-22 Fax: (800)

More information

Installation and Assembly: DUKANE PROJECTOR SHORT THROW WALL ARM

Installation and Assembly: DUKANE PROJECTOR SHORT THROW WALL ARM Installation and Assembly: DUKANE POJETO SHOT THOW WALL AM Model: UST-WALLAM3 POJETO POSITION FO 60" - 70" SEEN SIZE POJETO POSITION FO 70" - 100" SEEN SIZE 430-User Guide UST-WALLAM3-00 Do not begin to

More information

Installation and Assembly: Ceiling mount for LCD screens up to 29"

Installation and Assembly: Ceiling mount for LCD screens up to 29 Installation and Assembly: Ceiling mount for LC screens up to 29" Models: LCC 18, LCC 18-S, LCC 36, LCC 36-S Patent Pending Features: Comes in two adjustable height ranges (in 1" increments): 18"-30" and

More information

Installation and Assembly: Wireless Articulating Arm Wall Mount for 42" to 60" Flat Panel Displays

Installation and Assembly: Wireless Articulating Arm Wall Mount for 42 to 60 Flat Panel Displays Installation and Assembly: Wireless Articulating Arm Wall Mount for 42" to 60" Flat Panel Displays Model: WL-SA761PU-200 Maximum Load Capacity: 130 lbs (59 kg) 2300 White Oak Circle Aurora, Il 60502 (800)

More information

Installation and Assembly: Universal Projector Wall Arm

Installation and Assembly: Universal Projector Wall Arm nstallation and ssembly: Universal Projector Wall rm Model: SP-WLLRM-01 SP-CEL-UNV (sold separately) Max Load Capacity:35 lb (15.8 kg) Note: Read entire instruction sheet before you start installation

More information

SM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL

SM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL SM-RAZOR-F-M/L/XL Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done

More information

Installation and Assembly: Mount - Wall/Ceiling Mount

Installation and Assembly: Mount - Wall/Ceiling Mount Installation and ssembly: Mount - Wall/Ceiling Mount Model: DST360 Max oad Capacity: 150 lb (68. kg) 3215 W. North ve. Melrose Park, I 60160 (800) 729-0307 or (708) 865-8870 ax: (708) 865-2941 www.peerlessmounts.com

More information

SB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL

SB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum

More information

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

NEC Display Solutions of America, Inc.

NEC Display Solutions of America, Inc. NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NEC NP400, NP500, NP500W, and NP600 Projectors Model: NP600CM Maximum Load Capacity: 50 lb (22.7 kg) Features:

More information

NEC Display Solutions of America, Inc.

NEC Display Solutions of America, Inc. NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NP-M332XS, NP-M352WS, NP-M282X, NP-M283X, NP-M322X, NP-M323X, NP-M322W, NP-M323W, NP- M363X, NP-M363W, NP-M402X,

More information

INSTALLATION GUIDE. Flat Panel Arm Mount BTAR2/37. VESA 200x200 compatible. Support 24" to 37" Screens Max Load Capacity: 80 lbs (36 kg)

INSTALLATION GUIDE. Flat Panel Arm Mount BTAR2/37. VESA 200x200 compatible. Support 24 to 37 Screens Max Load Capacity: 80 lbs (36 kg) INSTALLATION GUIDE Flat Panel Arm Mount BTAR2/37 Support 2" to 37" Screens Max Load Capacity: 80 lbs (36 kg) VESA 200x200 compatible Note: Read entire instruction sheet before you start installation and

More information

Installation and Assembly: Projector Ceiling/Wall Mount

Installation and Assembly: Projector Ceiling/Wall Mount Installation and ssembly: Projector eiling/wall Mount Model# Max UL Load apacity EX, EX-S, EX-W, EX, EX-S, used with PRS projector mount 25 lb (11.3 kg) EX-W, EX, EX-S, EX-W used with PRG projector mount

More information

SB-WM-ART2-L-BL SB-WM-ART2-XL-BL

SB-WM-ART2-L-BL SB-WM-ART2-XL-BL SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier

More information

Tilting, Swiveling & Rotating Flat Panel Wall Mount

Tilting, Swiveling & Rotating Flat Panel Wall Mount Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical

More information

Installation and Assembly Manual: PRS Series Projector Mount

Installation and Assembly Manual: PRS Series Projector Mount Installation and ssembly Manual: PRS Series Projector Mount Models: PRS-1, PRS-1S, PRS-1W Features: ImageLock TM alignment prevents picture sag or drift Exclusive aluminum track quick release C U L US

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS P4263F Universal Low Profi le Flat Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888

More information

INSTALLATION GUIDE. Flat Panel Arm Mount MHA-72. VESA 750x850 compatible. Support 52" to 72" Screens Max Load Capacity: 300 lbs (136 kg)

INSTALLATION GUIDE. Flat Panel Arm Mount MHA-72. VESA 750x850 compatible. Support 52 to 72 Screens Max Load Capacity: 300 lbs (136 kg) INSTALLATION GUIDE Flat Panel Arm Mount MHA-72 Support 52" to 72" Screens Max Load Capacity: 300 lbs (136 kg) VESA 750x850 compatible Note: Read entire instruction sheet before you start installation and

More information

INSTALLATION GUIDE. Flat Panel Arm Mount MHA-800. VESA 500x800 compatible. Support 42" to 63" Screens Max Load Capacity: 200 lbs (91 kg)

INSTALLATION GUIDE. Flat Panel Arm Mount MHA-800. VESA 500x800 compatible. Support 42 to 63 Screens Max Load Capacity: 200 lbs (91 kg) INSTALLATION GUIDE Flat Panel Arm ount HA-800 Support 2" to 63" Screens ax Load Capacity: 200 lbs (91 kg) VESA 500x800 compatible Be sure to read this entire manual thoroughly and you fully understand

More information

INSTRUCTION MANUAL LCD TV BRACKET WM-3968

INSTRUCTION MANUAL LCD TV BRACKET WM-3968 INSTRUCTION MANUAL LCD TV BRACKET WM-3968 DEAR CUSTOMER In order to achieve the best performance of your product, please read this instruction manual carefully before using, and keep it for future reference.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone:

More information

INSTALLATION GUIDE. Flat Panel Arm Mount MLA100-L. VESA 100x100 compatible. Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg)

INSTALLATION GUIDE. Flat Panel Arm Mount MLA100-L. VESA 100x100 compatible. Support 10 to 24 Screens Max Load Capacity: 30 lbs (15 kg) INSTALLATION GUIDE Flat Panel Arm Mount MLA100-L Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg) VESA 100x100 compatible Note: Read entire instruction sheet before you start installation and

More information

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /

More information

Flat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold

Flat Panel Stand FPZ-655. for 32 to 55 Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination

More information

WARNING. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

WARNING. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. All-in-one Projector Adapter Plate I5300 series, I5500 series, and SP8602 series Model: SP-CEIL-ISTALL Maximum Load Capacity: 50 lbs/22 kg Read all instructions before you start installation and assembly.

More information

P4263TP. Installation Guide. Low-Profile Tilting Portrait Mount for Flat-Panels

P4263TP. Installation Guide. Low-Profile Tilting Portrait Mount for Flat-Panels Low-Profile Tilting Portrait Mount for Flat-Panels 1321 S. State College Blvd., Fullerton, CA 92831 USA Weight Limit Maximum Flat Panel Weight: 175 lbs. Warning Statements THE WALL STRUCTURE MUST BE CAPABLE

More information

Installation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS

Installation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand

More information

Installation and Assembly: 32" - 60" Flat Panel TV Cart

Installation and Assembly: 32 - 60 Flat Panel TV Cart nstallation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1M, SR560M R This product is UL Listed. t must be installed by a qualified professional installer. Max UL Load Capacity: 150 lb (68 kg)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS AM2 / AM2-B Articulating Swingout Arm NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone:

More information

Assembly Instructions for Model: MF110

Assembly Instructions for Model: MF110 Assembly Instructions for Model: MF110 Thank you for choosing a Sanus Systems VisionMount wall mount. The MF110 is designed to mount LCD flat panels with VESA (Video Electronics Standards Association)

More information

Tilting Flat Panel Wall Mount Installation Guide

Tilting Flat Panel Wall Mount Installation Guide Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees

More information

English FULL MOTION FLAT PANEL TV MOUNT. User Manual L102 TV Mount. 56 lb (25 kg) VESA. Supporting your digital lifestyle (

English FULL MOTION FLAT PANEL TV MOUNT. User Manual L102 TV Mount. 56 lb (25 kg) VESA. Supporting your digital lifestyle ( English User Manual L102 TV Mount FULL MOTION FLAT PANEL TV MOUNT ±12 19-32 56 lb (25 kg) 50x50-200x200 VESA ±180 3-17 (7.6-43.2 cm) Supporting your digital lifestyle Table of Contents Table of Contents

More information

Assembly Instructions for Model: VMDD26

Assembly Instructions for Model: VMDD26 Assembly Instructions for Model: VM26 Thank you for choosing a Sanus Systems Vision Mount wall mount. The VM26 is designed to mount up to 63 lat panel televisions weighing up to 175 lb. to a vertical wall.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

Installation Instruction

Installation Instruction Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry

More information

One Shelf, Wall Mounted A/V Component Stand Installation Guide Model: EX101SS

One Shelf, Wall Mounted A/V Component Stand Installation Guide Model: EX101SS One Shelf, Wall Mounted A/V Component Stand Installation Guide Model: EX0SS For technical assistance or troubleshooting please call -855-994-3832. This product is intended for use only with Audio/Video

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Premier Mounts Tilting Wall Mount Model: TWM-085 For use with Panasonic 85 Flat Panel NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount

Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP 850, SP 850P, SP 850-S, SP 850P-S Max Load Capacity: 150 lb (68 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or

More information

AM500-U Installation Guide

AM500-U Installation Guide 1321 S. State College Blvd., Fullerton, CA 92831 USA Included Components Maximum Flat Panel Weight: 500 lb. / 226.79 kg. Wall Mount Bracket (Qty 2) Cross Bar 5/16 Flat Washers (Qty 6) Universal Spacers

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations

More information

Full-motion Wall Mount

Full-motion Wall Mount Full-motion Wall Mount MD120409-01 AWM1521- AU Safety Instruction Component Checklist WARNING IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing.

More information

Dual Arm Tilt LCD Mount

Dual Arm Tilt LCD Mount Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,

More information

Owner s Manual Tilt Flat Screen Wall Mount

Owner s Manual Tilt Flat Screen Wall Mount Owner s Manual Tilt Flat Screen Wall Mount MODEL: DWT1327S CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! 75x75/100x100 27 MAX 40kg (88lbs) MAX Este

More information

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment

More information

Installation and Assembly Manual: PRS, RTR Series Projector Mount

Installation and Assembly Manual: PRS, RTR Series Projector Mount Installation and ssembly Manual: PS, T Series Projector Mount Models: PS-UNV, PS-UNV-S, PS-UNV-W PS-UNVP, PS-UNVP-S, PS-UNVP-W T-UNB, T-UNS, T-UNW This product is intended for use with UL Listed products

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Swingout Arm for 37 to 47 Flat Panels Model: AM80 NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888

More information

Owner s Manual Full Motion Flat Screen Wall Mount

Owner s Manual Full Motion Flat Screen Wall Mount Owner s Manual Full Motion Flat Screen Wall Mount MODEL: DWM1327SP CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! 75x75 100x100 27 MAX 15 kg (33 lbs)

More information

NOVA-EXT Versatile Projector Mount Model: NOVA-EXT

NOVA-EXT Versatile Projector Mount Model: NOVA-EXT INSTALLATION MANUAL NOVA-EXT Versatile Projector Mount Model: NOVA-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 800-368-9700 Fax: 800-832-4888 Other Locations

More information

Full-Motion TV Mount - 47" to 90" Installation Guide

Full-Motion TV Mount - 47 to 90 Installation Guide Full-Motion TV Mount - 47" to 90" Installation Guide Full-motion Articulating LCD/Plasma TV Wall-mount TV size: 47" - 90" Tilt angle: +/- 12 degrees Max load capacity: 200 lbs / 90 kg Wall distance (at

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS PDS-PLUS Universal Projector Mount Model: NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation

More information

FIXED-POSITION WALL MOUNT FOR TVs in.

FIXED-POSITION WALL MOUNT FOR TVs in. INSTALLATION GUIDE FIXED-POSITION WALL MOUNT FOR TVs 19-39 in. NS-HTVMFAB For wood-stud, solid concrete wall, or concrete block installations Safety information and specifications..... 2 Tools needed.............................

More information

SR560G SR560M. Flat Panel TV Carts. For 32" to 65" LCD and Plasma Flat Panel Screens. with Glass Shelf. with Metal Shelf

SR560G SR560M. Flat Panel TV Carts. For 32 to 65 LCD and Plasma Flat Panel Screens. with Glass Shelf. with Metal Shelf SR560G with Glass Shelf SR560M with Metal Shelf Flat Panel TV Carts For 32" to 65" LCD and Plasma Flat Panel Screens Peerless SmartMount Flat Panel TV Carts offer the most complete mobile solutions for

More information

Installation and Assembly: 32" - 60" Flat Panel TV Cart

Installation and Assembly: 32 - 60 Flat Panel TV Cart Installation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1G, SR560G R This product is U isted. It must be installed by a qualified professional installer. Max U oad Capacity: 150 lb (68 kg) screen

More information

Installing flat panels on the MPL15 wall mount

Installing flat panels on the MPL15 wall mount Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape

More information

LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns

LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32 with up to 200mm x 200mm VESA Mounting Patterns Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60

More information

flat panel solutions Specifications Box contents Warnings CAUTION: Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual

flat panel solutions Specifications Box contents Warnings CAUTION: Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual flat panel solutions Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual MST65BKR Fits TVs 37-65 Maximum Load Capacity 165 lb (75kg) Specifications Display Size: 37 to 65 Maximum Load:

More information

INSTALLATION GUIDE Ceiling TV Mount MHP-52

INSTALLATION GUIDE Ceiling TV Mount MHP-52 ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and

More information

LC6X4WTM Security Wall Mount with Tilt for up to 60" Flat Screens with VESA 600mm x 400mm or less

LC6X4WTM Security Wall Mount with Tilt for up to 60 Flat Screens with VESA 600mm x 400mm or less Page 1 of 6 The LC6X4WTM Security Wall Mount with Tilt is designed to secure a flat screen, up to a 60", to the wall while still allowing the monitor to tilt. The VESA mounting patterns on the front of

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small

More information

TP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3

TP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 TP63 FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount ASSeMBly INSTruCTIONS for your safety, please follow these precautions:!

More information

QLF215 INSTRUCTION MANUAL

QLF215 INSTRUCTION MANUAL QLF215 INSTRUCTION MANUAL We ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We re ready to help! 1 2 3 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

More information

AST-2446 INSTALLATION INSTRUCTIONS

AST-2446 INSTALLATION INSTRUCTIONS AST-2446 Suspension Adapter AST-2446 INSTALLATION INSTRUCTIONS Single Stud Installation Step 1. Secure the ceiling plate to the ceiling structure (see WARNING). Step 2. Use suitable hardware (commercially

More information

Installation and Assembly: Adjustable Extension Column (Pipe) 8" - 11"

Installation and Assembly: Adjustable Extension Column (Pipe) 8 - 11 Installation and ssembly: djustable Extension Column (Pipe) 8" - 11" Model: ELPMBC01 R This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 500

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series

INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series

More information

Fixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved

Fixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...

More information

Tilting & Swiveling Flat Panel Wall Mount Installation Guide Model: AXS2040

Tilting & Swiveling Flat Panel Wall Mount Installation Guide Model: AXS2040 Tilting & Swiveling Flat Panel Wall Mount Installation Guide Model: AXS2040 20-40 66 lbs. Supports VESA sizes up to: 200x200 For technical assistance or troubleshooting please call 1-855-994-2825 or visit

More information

MM750 Installation Instructions

MM750 Installation Instructions MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on

More information

Installation and Assembly:

Installation and Assembly: Installation and Assembly: PeerSound Wireless Short Throw Projector AV System PeerSound Wireless Short Throw Projector Audio System Models: WL-AU-PST600(A), WL-AU-PST1200(A), WL-AU-PST1600(A), WL-AU-PST600(A)-W,

More information

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series

INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option

More information

Small Above Fireplace Pull-Down Full-Motion TV Wall Mount

Small Above Fireplace Pull-Down Full-Motion TV Wall Mount Small Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 33123 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Short Throw Projector Arm Model: UNI-STA/UNI-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888

More information

19 to 39 TV WALL MOUNT - FULL MOTION

19 to 39 TV WALL MOUNT - FULL MOTION 19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5

More information

Installation and Assembly Manual: Vector Pro II

Installation and Assembly Manual: Vector Pro II Installation and ssembly Manual: Vector Pro II Models: PJF2-UNV, PJF2-UNV-S R This product is intended for use with U isted products and must be installed by a qualified professional installer. Maximum

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

Owner s Manual Tilt Flat Screen Wall Mount

Owner s Manual Tilt Flat Screen Wall Mount Owner s Manual Tilt Flat Screen Wall Mount MODEL: DWT60100XX CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! 200x200/300x300/400x200/ 400x400/600x400/800x400/

More information

Assembly Instructions for Model: VMPL3

Assembly Instructions for Model: VMPL3 Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will

More information