Line Following Circuit Board Wiring Guide
|
|
- Helena Lynn Summers
- 6 years ago
- Views:
Transcription
1 Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove the middle stubs from the analog optosensors using diagonal cutters or any other method that you want. Sand down any extra material, so the optosensor will be able to lay flush with the board when you solder. 3. Place the analog optosensor on the top side of the board, and make sure all four pins go through the board and that the symbols on the optosensor (diode and transistor) match the symbols on the board. The metallic spots on the circuit board are called pads. On reverse side, at each pad location where the pins poke through. Ensure solder connection is good by lightly tugging on the optosensor and checking for loose pins. Trim all the leads on the back of the board to make it as flat as possible.
2 4. Place the 180 Ohm resistor on the top side of the board next to the analog optosensor. Push each of the two pins through the holes in the board, so that the resistor lays flush against the board. Solder each end of the resistor to the terminals on the board. The resistor leads can be trimmed after soldering. Note: Orientation of resistors does not matter. Reverse side of the board should appear the same as in the following diagram on the left. Back Front METHOD A for Attaching Wires 5a. If you want to be able to remove your wire connectors (the wires that connect your line following board to your proteus) from the line following board, Method 1 is advised. Acquire a strip of long male header from the store. Cut away a three pin strip as shown in the following image. 6a. Bend the 3 pin strip into a right angle as shown in the following. You can bend it either by bending it against a hard surface, or by using needle nose pliers from the store.
3 7a. Insert the bent side of the header into the circuit board as shown. Solder the pins of the header to the backside of the circuit board. When soldering, the solder should flow over all of the pad and around the header pin. You can use diagonal cutters to shorten the pin leads. You will then need to take ribbon cable (a three wire strip), and solder this to a three-pin female header strip. The strip of ribbon cable should be long enough to reach from the Proteus controller to the underside of your robot design.
4 Method B for Attaching Wires 5b. If you do not want to be able to remove the wires from the circuit board with header connectors, consider Method B. Take three pieces of ribbon cable and strip approximately ¼ of an inch. Place the wires through the centered set of three holes on the board. Solder each wire to each hole. (See Diagram) Note: Wires can be soldered to either side of the board. As seen on the front side of the board, the left (grey wire) is ground, the middle (white wire) is +3.3V, and the right (black wire) is signal. Back Front Soldering Resistors and 4 Pin Male Header 6. Take the other three ends of the ribbon cable and solder them to a 4 pin male header strip (seen below). The specifications for which terminal is ground, +3.3V, and signal can be seen in the following image. Include the 68 kohm resistor as the pull up resistor between the signal and +3.3V pins.
5 7. Decide how far apart you want your other two optosensors by checking the spacing needed on the course for your specific line following algorithm. Place the other two analog optosensors with resistors equal distance apart on one of the four choices for spacing and repeat steps 2-6. Make sure to trim all the leads on the back of the board to make sure it can be mounted as flush as possible to the base of your robot. Also, make sure to cover the bottom of the circuit board when finished with electrical tape or some other insulator, so you do not short any of the sensors by contacting it with metal.
Bill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
More informationLine-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
More informationFROM SCHEMATIC TO VEROBOARD
FROM SCHEMATIC TO VEROBOARD The circuit of a bench amplifier utilising a LM386 linear (integrated circuit) IC and a few other components is used for this tutorial. The schematic is shown below: First a
More informationCustom Front Panel Upgrade Instructions
Custom Front Panel Upgrade Instructions Here are the directions for upgrading your SP-II to an SP-IIB, with a custom blackanodized front panel and engraved lettering. There are only forty SP-IIB s in existence
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationModifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
More informationSunday, November 4, The LadyUno Sound Unit
The LadyUno Sound Unit Here s what we ll need for this project We start with our finished Lady Ada Wav Shield. 5V for LCD Serial Data for LCD GND for LCD 5V (coming from the BBB) is_lady_ada_busy PIN GND
More informationIR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015
IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The
More informationTek-Bot Remote Control Transmitter Board Construction
Tek-Bot Remote Control Transmitter Board Construction Purpose This tutorial illustrates the procedure for construction of the Transmitter board for the Tek-bot. A Guide to Soldering Many of you have soldered
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationBombiniBot Parts and Assembly
BombiniBot Parts and Assembly Copyright 05 mindsensors.com / Parts Loose Parts: Part Quantity Tire Motor Mount 4-Wire Encoder Cable Encoder Wheel Velcro Strip Top Chasis Plate Bottom Chasis Plate Battery
More information4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com
4ms SCM Breakout Kit Builder's Guide for PCB v2.1 4mspedals.com Shuffling Clock Multiplier Breakout This guide is for building a Shuffling Clock Multiplier Breakout module (SCMBO) version 2.1 from the
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 3 16 9 16 9 8 3 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Antenna diagram showing configuration and lengths when assembled 7 8 16 9 16 9 Description The Pacific Antenna lightweight dual band dipole kit provides
More informationTekBot Remote Control Receiver Board Construction
TekBot Remote Control Receiver Board Construction Purpose This tutorial illustrates the procedure for construction of the Receiver board for the TekBot. A Guide to Soldering Many of you have soldered once
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 6 16 9 16 9 8 6 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationAssembly and Installation Instructions for White Oak Audio Design TM-1001 LED board
Thank you for purchasing White Oak Audio Design s TM-1001 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with your tuner.
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationFigure 1. CheapBot Line Follower
The CheapBot Line Follower v2.0 is a plug-in single-board sensor for almost any programmable robot brain. With it, a robot can detect the presence of a black or white zone beneath its two sensors. In its
More informationConnectors for Strip and Soldering Tips
Connectors for Strip and Soldering Tips Instructions for Connecting Power or Control Signals to 12 or 24 Volt DC LED Strip 11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567
More informationSoftRock v6.0 Builder s Notes. May 22, 2006
SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationA Deluxe LED Blinky That You Can Build!
Lux Spectralis A Deluxe LED Blinky That You Can Build! Assembly Instructions Contents Step 1: Parts check... 2 Step 2: Tool check... 3 Step 3: Install the computer chip... 3 Step 4: Install the resistors...
More informationFigure 1. CheapBot Smart Proximity Detector
The CheapBot Smart Proximity Detector is a plug-in single-board sensor for almost any programmable robotic brain. With it, robots can detect the presence of a wall extending across the robot s path or
More informationBill of Materials: General Purpose Alarm, Pulsed PART NO
General Purpose Alarm, Pulsed PART NO. 2190207 I hate alarms that sound continuously - unless they are smoke alarms. Smoke alarms should be annoying, but others should not. I wanted an alarm for a function
More informationAssembly Instructions
Assembly Instructions for the PA3 v2.0 Amplifier Kit PA3 Amplifier shown mounted on HS2 Heat Sink (The HS2 shown here is not included with this kit.) 27 February 2016 2013-2016 by Ralph Hartwell Spectrotek
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationDC Motor. Controller. User Guide V0210
DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,
More informationAssembly notes for RFX Teensy 3.x carrier board
Assembly notes for RFX Teensy 3.x carrier board Mark Pendrith , Dec 2014. Basic kit parts (BOM) 1 PCB mount 5mm/2.1mm DC barrel jack (see note below) 1 LD1117v33 1 1N5817
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More informationMICROGRANNY v2.1 - Assembly Guide
last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl
More informationHauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual
Hauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual Hauptwerk Hardware 2016 Page 1 Release 1.2 February 2016 Table of Contents Introduction...3 Parts Identification...4
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationGORE Aerospace Ethernet Cables
Termination Instructions The following procedures are based on Gore s best practices for terminating GORE Aerospace with the Carlisle Octax Connector System for both socket and plug versions. These procedures
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationLP-200 Dummy Load / Wattmeter
LP-200 Dummy Load / Wattmeter Enclosure Retrofit Assembly Instructions March 2009 TelePost Incorporated LP-200 is a trademark of TelePost Inc. Material in this document copyrighted 2009 TelePost Inc. 1
More informationQRPme Crystal Checker Kit Featured in FDIM 2011 Build-Along
QRPme Crystal Checker Kit Featured in FDIM 2011 Build-Along This crystal checker circuit was first presented in a workshop given by WA3OPY, AC5UR & W1REX a few years ago at the 4 States QRP Club gathering
More information66 Dodge Charger (and others) Tach board
66 Dodge Charger (and others) Tach board Introduction: This board replaces the original tachometer driver board in the 66 charger and other cars that use electronics external to the tachometer. The board
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationConnectors for Ribbon Flex and Soldering Tips
Connectors for Ribbon Flex and Soldering Tips 11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com Instructions for Connecting Power or Control
More informationAssembly instructions for the CS-1 ChemShield
Page 1 Of 6 Assembly instructions for the CS-1 ChemShield What is S.M.D SMD=Surface mount devices, like all the components does not have leads, but gets soldered onto flat solder pads. The CS-1 assembly
More informationSoftRock v6.0 Builder s Notes. April 6, 2006
SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),
More informationPacific Antenna Easy SWR Indicator Kit
Pacific Antenna Easy SWR Indicator Kit Description Monitoring the match of an antenna to your transmitter or adjusting an antenna tuner for best match requires an indicator of the reflected power as an
More informationV6.2 SoftRock Lite Builder s Notes. November 17, 2006
V6.2 SoftRock Lite Builder s Notes November 17, 2006 Be sure to use a grounded tip soldering iron in building the v6.2 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationFrivolous Engineering Useless Machine Soldering Instructions
Frivolous Engineering Useless Machine Soldering Instructions The electronics assembly for the Useless Machine is very easy to solder together. It consists of 11 parts as shown in the photo. Required tools
More information12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
More informationSpecimen Products Single Ended Stereo Amp Instruction Book
Specimen Products Single Ended Stereo Amp Instruction Book Specimen tube amplifier designs are informed by decades of servicing and building musical instrument amps. As a result of being subjected to the
More informationHow to solder SMD component on Awesome PCB or any other kind of PCB.
How to solder SMD component on Awesome PCB or any other kind of PCB. Step by step tutorial, with no steps to skip. Step 1 - What do we need? Step 2 - Fixing PCB Step 3 - Preparing for soldering Step 4
More informationBuilding a Bitx20 Version 3
Building a Bitx20 Version 3 The board can be broken into sections and then built and tested one section at a time. This will make troubleshooting easier as any problems will be confined to one small section.
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationInstructions for Building the Pulsed Width Modulation Circuit. MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08)
Instructions for Building the Pulsed Width Modulation Circuit MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08) Congratulations on your purchase of the MC-12 DC Motor
More informationLDB-1 Kit Instructions Page 1 of 8
LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed
More informationGold Wire Paper Clip Chain Wire Jewelry Making Pattern #103
Gold Wire Paper Clip Chain Wire Jewelry Making Pattern #103 More Jewelry Making Patterns at http://wire-sculpture.com/patterns/ Supplies Needed * Approximately 4 feet of 21 gauge 14 karat gold filled square
More informationBIG CEE. ENGINEERING 627 N Michigan Ave #5 Pasadena, CA
Garmin Emap power adapter housing BIG CEE ENGINEERING 627 N Michigan Ave #5 Pasadena, CA 91106 bigcee@bigcee.com www.bigcee.com This kit allows you to remove the circuit board from your Emap 12V adapter
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationRPS. XR Front Drive Updates CORPORATION
FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and
More informationPingable Envelope Generator
Pingable Envelope Generator Kit Builder's Guide for PCB v1.0.3 4mspedals.com PEG This guide is for building a Pingable Envelope Generator (PEG), which is an intermediate-level kit. You should be confident
More informationW7MRI's Anderson Powerpole. Power Hub
W7MRI's Anderson Powerpole Power Hub This PDF is provided by K7JM at http://radio.mcdougallshome.net Don, W7MRI made up a nice small circuit board that holds 7 pairs of Anderson Powerpole connectors to
More informationModel 333 Single Channel USB Chromatography Data System Relay ( Contact Closure ) Installation
Remove the four screws holding the Model 333 A/D board in the stand-alone box. If the 333 is installed in a GC or HPLC, remove the four hex head screws from the outside of the instrument which secure the
More informationESRA III. Expressive System for Robotic Animation
ESRA III Expressive System for Robotic Animation 1 ESRA III Kit Contents 1 Hitec Servos 8 Upper Eye Support 2 Dagu (New as of 7/12) 9 Lower Eye Support 3 Eye Balls 10 Main Support 4 Flat Servo Plate 11
More informationEurorack DIY Kit Instructions. All Thonk kits are sold under our standard Terms and Conditions -
MA VCA OVERVIEW For the most recent version of this document please visit http://thonk.co.uk/documents/ma/ For all technical support please visit http://bit.ly/1tl78e0 on Muffwiggler. All Thonk kits are
More informationCongratulations on your purchase of the SparkFun Arduino ProtoShield Kit!
Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping
More information1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs
97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationOpen Air. Kit includes: Drawer Full Indicator board assembly, (2) retainers, and (4) screws. PREPARATION
Open Air Installation Video You will need: 8-inch #2 Phillips screwdriver Needle-nose pliers DFI INSTALLATION GUIDE For installation videos, visit the Customer Service playlist at www.youtube.com/user/thelitterrobot
More informationupad Proto Base Assembly Guide v2.0
upad Proto Base Assembly Guide v2.0 Last Updated September 1, 2015 Table of Contents Preface... 3 Introduction... 3 Required Tools... 3 Flux Pen... 3 Soldering Iron... 3 Solder... 3 Diagonal Cutters...
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationConstruction Guide European Version
Construction Guide European Version PCB This section describes how to build up the DRO-350 printed circuit board (PCB). The bare PCB is available for purchase on the order page. Static Protection Bare
More informationJabiru Installation instructions
Page 1 of 5 s Step Description 1 Mark out centre line of the installation 2 Align centre line of installation with the centre line of the "Front Panel Cut out" template. Align "FLOOR" on template with
More informationThe Centimani Servo Power Board
The Centimani Servo Power Board Email: srlm@srlmproductions.com Abstract This document discusses the procedure required to build a Centimani Servo Power Board and the capabilities of the board. This board
More information2 Recommended Tools / Supplies
Bias Scout TM Kit Assembly Manual Version 3.1 25 March 2015 1 Inventory of Parts 1 ea octal socket 1 ea octal base, brown (1 3/16" dia x 7/8" high) 1 ea 1.0 / 1W metal oxide, flame proof resistor 1 ea
More informationROVs in a Bucket Building an Underwater Robot. 5.0 Building the Tether
5.0 A professional ROV is connected to the controller box by strands of wire. The bundle of wires are encased in a single sheath. The connecting wire is called the tether. In our project the tether is
More informationCommScope Tool-less IDC Instruction Sheet Connector Block Issue 3, February 2004 Material ID
CommScope Tool-less IDC 201-208-101-02 Instruction Sheet Connector Block Issue 3, February 2004 Material ID 848 586 103 General This instruction sheet provides general procedures for mounting Tool-less
More informationWARNING! ETCHED PARTS CONTAINED IN THIS KIT HAVE SHARP POINTS, EDGES AND CORNERS.
MPD18 chassis build instructions K A (see below for details) J I G H L C D F E B M Parts list: Ident Quantity A Etched Nickel/Silver fret 1 B Wheel sets 2 C Worms 2 D Worm gears 2 E Shaft adapters 2 F
More informationProf. Steven S. Saliterman Introductory Medical Device Prototyping
Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ You must complete safety instruction before using tools and equipment in
More informationBuild this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ
Build this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ A great tutorial for adding a keypad to the DDS Kit by Bruce, W8BH This manual has been prepared to be read directly on screen.
More informationSpiderbeam Balun Construction Guide
BALUN CONSTRUCTION GUIDE Ver. 1.0 1 The components of the Balun Kit are in a plastic bag. Most of the components are inside the plastic case of the balun. The aluminum U-profile and the RG-142 Teflon Coax
More informationDesigned by Melissa DiRenzo thesweetescape.ca
instructions Designed by Melissa DiRenzo thesweetescape.ca YOU WILL NEED 3 -diameter foam ball Christmas sweater Hot glue gun and glue sticks 3/8 -wide satin ribbon Elastic thread: metallic Note: A child
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationPTM Jazz Bass Control Plate Installation Revised: March 2, 2011
PTM Jazz Bass Control Plate Installation Revised: March 2, 2011 Before you start, read these instructions first to understand what you need to do to install this product. Assumptions This patented Pickup
More informationTen Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
More informationFoxhunt Offset Attenuator. Parts List:
When your closing in on the fox you may find the signals to be so strong that you can no longer find a peak or null with your antenna. Sometimes the signal is so strong that the RF will leak straight into
More informationStanley Hand tools Stanley FatMax push-lock adjustable joint pliers. 3 piece Stanley FatMax pushlock. Stanley FatMax groove joint pliers.
Stanley FatMax push-lock adjustable joint pliers Slip-resistant Bi-Material handle for a comfortable grip. Multipurpose jaws designed to grasp flat and round objects. Push-Lock technology allows for quick
More informationApplication Note. Bowser-Stewart VO-1000 Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-1000 Digital Sound Decoder into the Bowser-Stewart VO-1000 Locomotive. Skill Level 4: The entire installation can be completed
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationFind a place where you can work through completion, without disturbing your
Scan by Manual Manor ARIES SYSTEM 300 MUSIC SYNTHESIZER Page I of 4 MODULE AR-334 SEQUENCER ASSEMBLY INSTRUCTIONS It is recommended that you do the following before you proceed: Find a place where you
More informationPSU for LawMate 500mW Transmitters. Assembly and Operation Manual
PSU for LawMate 500mW Transmitters Assembly and Operation Manual Introduction Thank you for purchasing LawMate 500mW Power Supply. This power supply was specifically designed for the 500mW LawMate transmitter
More information