Jabiru Installation instructions

Size: px
Start display at page:

Download "Jabiru Installation instructions"

Transcription

1 Page 1 of 5 s Step Description 1 Mark out centre line of the installation 2 Align centre line of installation with the centre line of the "Front Panel Cut out" template. Align "FLOOR" on template with floor of vehicle. Tape template in place 3 Drill 4 x 10mm holes in the corner of the cut out region. Remove template. Use jig saw to cut out between the outside of the 10 mm holes 4 Align centre line of "Floor cut out" template with centre line of installation. Align front face of cupboard with line on template. Tape template in place 5 Drill the 10mm holes as marked on floor cut out template. Use jig saw to cut out the areas between the 10mm holes

2 Page 2 of 5 6 Align centre line of installation with centre line of "Rear exhaust cut out" template". Align fold in template with corner of floor and rear wall. Tape template in place 7 Drill 4 x 10mm holes as marked on cut out template. Use jig saw to cut out the area between the 10mm holes If required, cut out hole for power cord access. A minimum hole of 38mm diameter is required in the position shown (438mm back from the front face of the cupboard & 113mm up from the floor) 8 Install bracing around both sides of the front cupboard cut out. This material should be at least 25x50mm and securely attached to the inside face of the cupboard

3 9 Stick the base sealing gasket around the perimeter of the cut outs in the floor Page 3 of 5 10 Lay the metal slipper over the gasket with the folded end just outside the cupboard. 11 Position the unit into the cut out. Slide the unit over the top of the slipper into the cut out and push all the way in until the front of the unit is flush with the front of the cupboard 12 Hold the unit in position and pull out the slipper, leaving the unit sitting on the sealing gasket. Note: A pair of pliers or mole grips may be required to pull out the slipper

4 Page 4 of 5 13 Locate three holes on the inside of the units sheet steel cover. Use screws provided to secure the unit to the bracing. Repeat for three holes on other side of unit 14 Locate the control cable plug on the printed circuit board at the back of the fascia Take the grey control cable from the unit and plug it into the socket on the board. Take care to ensure that the plug is around the correct way and is fully engaged. 13 Push fascia into position. Use the fascia as a guide to drill 6 x 3mm pilot holes for the attachment screws. Install fascia with six screws and cover with screw caps

5 Page 5 of 5 14 Insert condenser duct through the hole in the external wall and inside the condenser air spigot. Ensure the duct is pushed in as far as possible. Trim excess duct so it is flush with outside wall. 15 Insert external condenser grill inside the duct. Fix in place with 4 screws. Cover screw heads with push in plugs provided NOTE - Ensure that the grille is installed as shown with the louvers sloping downwards to prevent rain entering duct. 16 Plug the 3 pin IEC service cable into the socket Refer to step 7 for the location of this hole 17 Installation complete

BX1956 Installation Instructions Chrysler PT Cruiser (Include Turbo)

BX1956 Installation Instructions Chrysler PT Cruiser (Include Turbo) BX1956 Installation Instructions 2001-04 Chrysler PT Cruiser (Include Turbo) Serial No. The front fascia and metal bumper are removed for baseplate installation. Factory metal bumper will not be reinstalled.

More information

B as e plate s Honda Accord (Incl. LX, EX, DX) (no foglights) BX2242. Serial Number. Installation Instructions

B as e plate s Honda Accord (Incl. LX, EX, DX) (no foglights) BX2242. Serial Number. Installation Instructions B as e plate s Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed

More information

Installation Instructions

Installation Instructions Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as

More information

G. H. I. N. J. O. 22"x 28" Poster Holder. P. Q. romotional wall displ

G. H. I. N. J. O. 22x 28 Poster Holder. P. Q. romotional wall displ Wall Display Assembly Instructions Tools necessary for assembly 1. Electric drill with Phillips head 2. Adjustable wrench or pliers 3. One or two step ladders or stools Due to the weight of the side panels

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTAING UNIT BR Window Mounting (0,000 -,000 BTU) INSTAATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. be

More information

GE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.

GE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models. GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:

More information

Installation Instructions

Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

INSTALLATION MANUAL 32273/1205 C C-403 GB - F - D - NL - ES - I - S - SLO

INSTALLATION MANUAL 32273/1205 C C-403 GB - F - D - NL - ES - I - S - SLO INSTALLATION MANUAL 32273/1205 C-402 - C-403 GB - F - D - NL - ES - I - S - SLO 1A 1B ENGLISH GENERAL INFORMATION The Cassette toilet is available in 2 types: C-402 Cassette toilet with built-in water

More information

Small Flush Wood Flue Adapter Installation Instructions (SKU )

Small Flush Wood Flue Adapter Installation Instructions (SKU ) Warning Regarding Draft Use of any offset adapter may degrade draft performance of the insert. To minimize the adverse effects, set the adapter to the minimum offset possible. Any leaks in the adapter

More information

BSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers

BSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers BSM, GSM & GSS Joint Kit Instruction (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers February, 1999 JOINT ASSEMBLY PARTS LIST Item Quantity Description

More information

NISSAN NV200 CHEVY CITY EXPRESS WALL LINER KIT INSTALLATION INSTRUCTIONS

NISSAN NV200 CHEVY CITY EXPRESS WALL LINER KIT INSTALLATION INSTRUCTIONS NISSAN NV200 CHEVY CITY EXPRESS WALL LINER KIT INSTALLATION INSTRUCTIONS NOTES: 1. Before commencing, remove all wall liners and D Rings already installed in the vehicle. 2. Consult layout PDF and compare

More information

WARNING BX1514. Serial Number Buick LaCrosse Installation Instructions

WARNING BX1514. Serial Number Buick LaCrosse Installation Instructions Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

EPS Duct Fabrication and Installation Sheet

EPS Duct Fabrication and Installation Sheet EPS Duct Fabrication and Installation Sheet EPS Cooling Duct for 2014-2016 Corvette Parts Required for Fabrication: Description Quantity Templates for EPS Duct 2 Template for Front Compartment Air 1 Deflector

More information

Instructions to fit Emulator in place of floppy drive M.D.R.

Instructions to fit Emulator in place of floppy drive M.D.R. Instructions to fit Emulator in place of floppy drive M.D.R. Before starting, read through all the following instructions, and then when you do begin, read each number section before attempting that particular

More information

BX2520 Installation Instructions 2004 Mazda 3

BX2520 Installation Instructions 2004 Mazda 3 BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.

More information

MISCELLANEOUS CABINET REPAIRS

MISCELLANEOUS CABINET REPAIRS MISCELLANEOUS CABINET REPAIRS 167 168 NOTES MISCELLANEOUS CABINET REPAIRS Cabinet Panel Repairs 175 SIDE PANEL REPLACEMENT - GDM SERIES INSTALLATION INSTRUCTIONS Tools Required 1/8" drill Rivet Tool Silicone

More information

BX1956 Installation Instructions Chrysler PT Cruiser (Include Turbo)

BX1956 Installation Instructions Chrysler PT Cruiser (Include Turbo) BX1956 Installation Instructions 2001-04 Chrysler PT Cruiser (Include Turbo) Serial No. The front fascia and metal bumper are removed for baseplate installation. Factory metal bumper will not be reinstalled.

More information

Pre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator

Pre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator Pre-Paint>Fuselage>Empennage>Fit elevator Objectives of this task: To fit the elevator to the horizontal stabiliser, to fit the trim tabs to the elevator and the end caps to the elevator and the horizontal

More information

Kit 102 Series Installation Instructions for Wood or Metal Posts on Level Runs

Kit 102 Series Installation Instructions for Wood or Metal Posts on Level Runs Kit 102 Series Installation Instructions for Wood or Metal Posts on Level Runs A. Drill Posts Hole size for 1/8" or 3/16" cable installation This kit may also be used for stairs or runs that exit the end

More information

WARNING Honda Civic SI Installation Instructions BX2241. Serial Number

WARNING Honda Civic SI Installation Instructions BX2241. Serial Number Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

Installation Instructions For Slider Casement Air Conditioners

Installation Instructions For Slider Casement Air Conditioners Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means

More information

READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU)

READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU) READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

Blackout Instructions. 4 R-Series Fascia Installation Outside Mount

Blackout Instructions. 4 R-Series Fascia Installation Outside Mount Blackout Instructions 4 R-Series Fascia Installation Outside Mount 1 Components Needed page 3 Tools Needed page 4 System Diagram page 5 Instructions Step 1: Install Brackets. Page 6 Step 2: Mount Back

More information

INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D APPLICATION: F87 M2

INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D APPLICATION: F87 M2 INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0026 APPLICATION: 2016-17 F87 M2 Congratulations for being selective enough to use a Dinan Intercooler Upgrade Kit. We have spent many hours

More information

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment. Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment. Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

2009 Acura TL Installation Instructions

2009 Acura TL Installation Instructions Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. Serial Number BX1670 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

END FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"

END FRAMES. End frames built using pressure treated 2x4 (1 1/2 x 3 1/2) 36 34 7/16 pilot hole. 5 1/2 x 1/2 lag bolt 8 wheel 23 END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat

More information

Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application

Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,

More information

Installation Guide. Model #400. Corporate Office: 349 Highland Road East Macedonia, Ohio

Installation Guide. Model #400. Corporate Office: 349 Highland Road East Macedonia, Ohio Installation Guide Model #400 Corporate Office: 349 Highland Road East Macedonia, Ohio 44056 1.866.822.7328 www.ezbreathe.com Copyright 2006, EZ Breathe, LLC WHAT S INSIDE Before installing your EZ Breathe

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTALLING UNIT Compact Window Mounting (0~K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this

More information

MINI Cooper Model 120SA Installation Instructions

MINI Cooper Model 120SA Installation Instructions MINI Cooper Model 120SA Installation Instructions Please read these instructions completely before beginning the installation. Test fit all components (amplifier, etc.) before mounting. These instructions

More information

Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions

Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions The below installation instructions work for the following products: Mustang Eleanor Style Louvers - Pre-painted (05-10)

More information

GV Standard Sliding Over Roof Installation Instruction Manual

GV Standard Sliding Over Roof Installation Instruction Manual GV Standard Sliding Over Roof Installation Instruction Manual Technical experts in the design, manufacture and supply of precision engineered, architectural rooflights for residential and commercial buildings.

More information

Lid, Floor Monument and Two Installation Fixtures. Floor Monument Installed with Lid On and Off

Lid, Floor Monument and Two Installation Fixtures. Floor Monument Installed with Lid On and Off Monumentation Drilling Specifications: Floor Monuments: - Floor is drilled using 1 3/4" core drill bit to a depth of 2 with a Hilti rotary hammer drill - Quikrete is used to set monuments into the floor

More information

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly

More information

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment. Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

installation instructions For Slider Casement Air Conditioners

installation instructions For Slider Casement Air Conditioners installation instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

CAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo:

CAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo: Octagon Wood Gazebo Kit Contents Hardware included for assembling your gazebo: 5/16" Lag Bolts Use to fasten post to floor 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten

More information

Gambrel Barn Construction Manual 8x8 through 16x24 Units

Gambrel Barn Construction Manual 8x8 through 16x24 Units Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little

More information

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required: DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket

More information

Inde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P

Inde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall

More information

INS A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Verify Curb Installation Required Installation Tools...

INS A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Verify Curb Installation Required Installation Tools... INS-88.300-0A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Verify Curb Installation... 2 2. Required Installation Tools... 2 3. Unpacking the KSR... 3 4. Attach KSR Bottom Rail to Curb... 5 5. Attach

More information

INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE

INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE March 2013 DOOR 2 Page 1 of 5 INSTALLATION INSTRUCTIONS NEO ANGLE 6MM FRAMELESS AND 4MM FRAMED SHOWER DOOR DANUBE, DELTA, SIGNATURE, OCEANIA, CASCADE

More information

BX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT

BX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate

More information

* Drill and 3/32" drill bit: for drilling holes in the factory plastic upper for the screws to secure the brackets (factory upper installation only)

* Drill and 3/32 drill bit: for drilling holes in the factory plastic upper for the screws to secure the brackets (factory upper installation only) * Two slider windows (four sliders windows for the 4-door kit) * Four brackets to secure the windows to the upper door frames (8 brackets for the 4-door kit) * Weatherstrip to seal the windows to the half

More information

Assembly Instructions Nevins Phone Booth

Assembly Instructions Nevins Phone Booth Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/2 phillips head Screw 1 - (24)

More information

Gambrel Barn with Overhang Manual

Gambrel Barn with Overhang Manual Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH

More information

Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware.

Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. 2 Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. Apply masking tape to the top of the bumper cover underneath

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTALLING UNIT MSII MSIII Window Mounting (5,000~8,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully

More information

1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions 1. 2.

1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions 1. 2. 1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions Right Stack top panels on bottom panels Unfold display wall Set in desired configuration Wrong Pull from here Remove each folded

More information

Classic SportBar Camaro V6 or V8

Classic SportBar Camaro V6 or V8 Classic SportBar 2011-2015 Camaro V6 or V8 The Classic SportBar is intended for restyling purposes only and does NOT provide roll over protection. Read entire installation guide before starting. Component

More information

INSTRUCTION SHEET U19

INSTRUCTION SHEET U19 U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single

More information

The easy way to an affordable kitchen

The easy way to an affordable kitchen quality, affordable, pre-assembled The easy way to an affordable kitchen In association with All Insta-Cupboard carcass units are supplied pre-assembled to simplify installation Choose the colour of your

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

More information

ATLANTIS RAIL Contact Information

ATLANTIS RAIL Contact Information ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products

More information

3.2.3 Rear Door Window and Quarter Window Carrier Assembly

3.2.3 Rear Door Window and Quarter Window Carrier Assembly Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without

More information

WARNING Honda Civic SI Installation Instructions BX2241. Serial Number

WARNING Honda Civic SI Installation Instructions BX2241. Serial Number Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

WARNING Mercedes Smart for two CDI Installation Instructions BX1990. Serial Number

WARNING Mercedes Smart for two CDI Installation Instructions BX1990. Serial Number Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

33/3527A. Devices covered by these instructions: 33/3527A-F (Fire) Surface Vertical Rod Exit Device

33/3527A. Devices covered by these instructions: 33/3527A-F (Fire) Surface Vertical Rod Exit Device *911403-00* 911403-00 Surface Vertical Rod Exit Device 33/3527A Installation Instructions Devices covered by these instructions: 33/3527A Surface Vertical Rod Exit Device 33/3527A-F (Fire) Surface Vertical

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.

More information

Installation Instructions

Installation Instructions READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes

More information

WARNING. B as e plate s. BX Saturn L Series Installation Instructions. Serial Number

WARNING. B as e plate s. BX Saturn L Series Installation Instructions. Serial Number B as e plate s BX3323 Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to

More information

Installation and Operating Instructions

Installation and Operating Instructions INSTRUCTIONS Installation and Operating Instructions In these installation instructions is described the replacement of the elevating support with gas springs. This conversion kit applies to all California

More information

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com THANK YOU for purchasing from smith+noble. Your new window treatments have been

More information

FORD ESCAPE/KUGA SUV CARGO BARRIER INSTALLATION INSTRUCTION

FORD ESCAPE/KUGA SUV CARGO BARRIER INSTALLATION INSTRUCTION This cargo barrier is capable of being located in two positions, behind the 2nd row of seats with the seats in an upright position, and behind the 1st row of seats with the 2nd row of seats in their folded

More information

ALLORA SWING PANEL INSTALLATION INSTRUCTIONS

ALLORA SWING PANEL INSTALLATION INSTRUCTIONS ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:

More information

Installation Instructions

Installation Instructions edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung

More information

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully

More information

TRANSIT 148 HIGH ROOF WALL LINERS INSTALLATION INSTRUCTIONS

TRANSIT 148 HIGH ROOF WALL LINERS INSTALLATION INSTRUCTIONS TRANSIT 148 HIGH ROOF WALL LINERS INSTALLATION INSTRUCTIONS NOTES: 1. Before commencing, remove all wall liners and D Rings already installed in the vehicle. 2. Consult layout PDF and compare vehicle layout

More information

Pontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia

Pontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia Aftermarket Front Fascia be used correctly to install the secondary fascia to the existing fascia. 1 Fascia Front 5 Bolt M6-1.0x60 5 Washer 1/4x9/16 2 Bolt/Washer Assembly 1 Nut/Washer Assembly 1. Six

More information

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY.

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. IT IS RECOMMENDED TO USE A TRAINED SHOWER INSTALLER FOR THIS SHOWER TO OBTAIN THE BEST INSTALLATION. D Square

More information

V Installation instructions, accessories. Auxiliary seat. Volvo Car Corporation Gothenburg, Sweden V70 (00-08) 2002

V Installation instructions, accessories. Auxiliary seat. Volvo Car Corporation Gothenburg, Sweden V70 (00-08) 2002 Installation instructions, accessories Instruction No 8624018 Version 1.3 Part. No. 30749269, 30749270, 30749271, 30749272, 30749273, 30749274 Auxiliary seat M8901699 Volvo Car Corporation Auxiliary seat-

More information

WARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions

WARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and

More information

HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750

HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 Important Note: Upgrading the track system on the HQ Studio Frame requires the use of this 2 Extension Kit (Part #QF09750),

More information

NORMAN SHUTTERS INSTALLATION INSTRUCTIONS. 4 Sided Z Frame. (Inside Mount - 2 panel) Getting Started

NORMAN SHUTTERS INSTALLATION INSTRUCTIONS. 4 Sided Z Frame. (Inside Mount - 2 panel) Getting Started NORMAN SHUTTERS INSTALLATION INSTRUCTIONS 4 Sided Z Frame (Inside Mount - 2 panel) Getting Started Recommended Tools: Nail Gun or Drill, Tape Measure, Torpedo Level, Box Knife, 6 Philips head driver Make

More information

Water Line and Water Line Assembly Gasket

Water Line and Water Line Assembly Gasket 1 Preparation for Repair 1) Remove tip from scaler 2) Remove scaler from air supply 3) Remove gasket from back end of scaler. Examine gasket for obvious wear or disfigurement. Replace if necessary. 2 Remove

More information

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement

More information

4 Position the Suntile to the x tile s position and mark the felt around the square box flange. Then remove the Suntile

4 Position the Suntile to the x tile s position and mark the felt around the square box flange. Then remove the Suntile 4 Position the Suntile to the x tile s position and mark the felt around the square box flange. Then remove the Suntile 5 Using a sharp bladed knife, cut through the felt from corner to corner in an x

More information

BX Honda Accord Hybrid No Foglights Installation Instructions

BX Honda Accord Hybrid No Foglights Installation Instructions Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers

More information

Removing outter components

Removing outter components Y Axis Motor Replacement Replacing the Y axis motor is a process that requires the individual to be somewhat mechanically inclined and can follow detailed instructions. If any of the following steps are

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been

More information

Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.

Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2. Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit

More information

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. Serial Number BX2187 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

Assembly Instructions Nevins Phone Booth

Assembly Instructions Nevins Phone Booth Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Socket Wrench Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/4 phillips head

More information

Octagon Vinyl Gazebo Assembly Instructions

Octagon Vinyl Gazebo Assembly Instructions Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS

IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the

More information

Joiner Kit For Models N388, C450, E402B, E411T, E415H, E440T, E442B, E521T and E522B

Joiner Kit For Models N388, C450, E402B, E411T, E415H, E440T, E442B, E521T and E522B Joiner Kit For Models N388, C450, E402B, E411T, E415H, E440T, E442B, E521T and E522B KIT COMPONENTS Part Illustration Description Rear Bracket Front Lower Bracket Front Upper Bracket KIT APPLICATION This

More information

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly

More information

Keypad Lock Retrofit Kit for Follett REF Undercounter Refrigerator P/N

Keypad Lock Retrofit Kit for Follett REF Undercounter Refrigerator P/N Materials supplied Reference # Keypad assembly (housing and mounting base) 1 Keypad housing base 2 Lock mechanism with cable 3 (9) 8-32 x 1/2" stainless steel screws 4 Latch 5 Jig 2, latch 6 Jig 1, keypad

More information

Installation Manual. This installation is for the Odyssey H1800 Series Ventilation System.

Installation Manual. This installation is for the Odyssey H1800 Series Ventilation System. Installation Manual This installation is for the Odyssey H1800 Series Ventilation System. This installation is limited to roofs with pitches between 3 and 35. This instruction assumes that there is a power

More information

Section 1 Cubicles. Section 2 IPS Duct Panel Systems. Section 3 - Vanity Units Components & Assembly 12. Section 4 Basic Maintenance.

Section 1 Cubicles. Section 2 IPS Duct Panel Systems. Section 3 - Vanity Units Components & Assembly 12. Section 4 Basic Maintenance. Contents Section 1 Cubicles Cubicle Components 3 Cubicle Installation 4-5 Cubicle Fittings Brackets 6 Hinges 7 Partition Support Leg 8 Indicator Bolt 9 Section 2 IPS Duct Panel Systems Frame, Flash & Panel

More information