INSTALLER S MANUAL 2 MICROWAVE OVENS
|
|
- Samantha Anastasia Stevenson
- 5 years ago
- Views:
Transcription
1 Page Nº: 9 of 95 2 MICROWAVE OVENS Check that all the technical information appearing on the specification plate corresponds to the characteristics of the mains electrical supply in question (voltage and frequency). Remove all packaging materials and accessories from the inside of the oven. Check that the door, hinges, oven front and all interior and exterior parts of the microwave are in perfect condition. Place the oven on a flat surface which can withstand its weight. In order to ensure adequate cooling, it is recommended that the microwave is placed in a cabinet that ihas an opening at the top. Ensure that the connection to the mains supply is adequately earthed. 9
2 Page Nº: 10 of INSTALLATION ACCESSORIES: Lateral Spacer Frontal Spacer Frontal Spacer - II Screw B 4.2 x 19 PT K 35 x 10 WN 10
3 Page Nº: 11 of 95 11
4 Page Nº: 12 of 95 Column installation 1) Place the top fixing supports in a cabinet with a distance of 350 mm between axes. 2) Introduce the microwave in the gap of the recess and set the 4 adjustable feet to their highest position, ensuring that the I and II marks coincide. The height of the oven feet can be altered by turning them 180º. At their highest, they provide an elevation of 50 mm. 3) Cut the flanges of the lateral supports to the width of the recess gap before securing them to the front feet of the microwave. 4) Fix the microwave feet to the lower supports 5) Position the frame and screw it to the upper and lower parts of the wall. 12
5 Page Nº: 13 of 95 13
6 Page Nº: 14 of 95 14
7 Page Nº: 15 of 95 Installation under worktop surface: 1) Place the top fixing supports in a cabinet with a distance of 350 mm between axes. Given that in this type of installation, the frame for the microwave is in a lower position, the bottom supports are wider in order to ensure greater support for the frame. 2) Introduce the microwave in the gap of the recess and place the 4 adjustable feet perfectly flat at their lowest position, making sure that positions I and II coincide. The height of the feet can be adjusted by turning them 180º. At their lowest position, they provide an elevation of 40 mm. 3) Cut the flanges of the lateral supports to the width of the recess gap before securing them to the front feet of the microwave. 4) Fix the microwave feet to the lower supports 5) Position the frame by placing it on the top supports. This type of installation allows a worktop surface to be placed above the microwave. The new system allows the upper part of the frame to be fitted without the need for fastening screws. 15
8 Page Nº: 16 of 95 16
9 Page Nº: 17 of 95 17
10 Page Nº: 18 of 95 Installation in a overhead cabinet 1- Place the fixing supports in a cabinet with a distance of 350 mm between axes. Given that in this type of installation, the frame for the microwave is in a lower position, the bottom supports are wider in order to ensure greater support for the frame. 2- Introduce the microwave in the gap of the recess and place the 4 adjustable feet perfectly flat at their lowest position, making sure that positions I and II coincide. The height of the feet can be adjusted by turning them 180º. At their lowest position, they provide an elevation of 40 mm. 18
11 Page Nº: 19 of 95 19
12 Page Nº: 20 of 95 20
13 Page Nº: 21 of 95 Recess frame for free installation of microwave Cover B Cover A Lateral Spacer Foot accessory Frontal Spacer - II Screw B 4.2 X 19 DIN 7981 zinc. Screw PT K 35 X 25 21
14 Page Nº: 22 of 95 22
15 Page Nº: 23 of 95 23
16 Page Nº: 24 of 95 24
17 Page Nº: 25 of 95 A) Introduce the oven in the cabinet until the frame is aligned B) Open the door of the oven and fix it to the lateral walls of the cabinet with the four screws supplied in the 4 holes of the oven frame. 25
DOLCE STIL NOVO. Tips & tricks for a perfect alignment Consigli e suggerimenti per un perfetto allineamento
DOLCE STIL NOVO Tips & tricks for a perfect alignment Consigli e suggerimenti per un perfetto allineamento EN This installation manual is accompanied by a demonstration video that can be viewed at: www.youtube.com/user/smegspa
More informationINSTRUCTIONS FOR VARIABLE WORKTOP JIG MM
INSTRUCTIONS FOR VARIABLE WORKTOP JIG 250-1000MM Please read these following points carefully before cutting: 1. Before using the jig we recommend you practice a few joints with off-cuts of worktops or
More informationMerloni Elettrodomestici. Technical Fitting Manual FRIDGE. Language Issue/Edition Page GB /
GB 99-11-03/01 1-38 Index 1 CONFORMITY OF APPLIANCE 3 2 MAIN ASSEMBLY TYPES 3 2.1 Under worktop 3 2.2 Double door 10 2.3 Combined 14 2.4 Single door Fridge or single door Freezer 19 2.5 Combined free-standing
More informationInstallation Instructions Evolve Cabinets
Installation Instructions Evolve Cabinets Follow these installation instructions for Evolve upper, base, tall, and scope cabinets with AireCore or wood composite construction. Tools needed: Flat head screwdriver
More informationMounting Instructions Item No.: /521/522/420/421/422
Mounting Instructions Item No.: 541.35.520/521/522/420/421/422 Revolving Corner Unit In addition to these general mounting instructions, please refer to the fitting instructions, where the individual drilling
More informationIn addition to this general mounting and adjustment instruction you need the fitting specification document, where the individual drilling dimensions
Mounting and Adjustment Instruction for corner carrousel fitting In addition to this general mounting and adjustment instruction you need the fitting specification document, where the individual drilling
More informationHandleless Uni t Specification
Handleless Uni t Specification QUALITY BRITISH CRAFTSMANSHIP 160 Handless Fitting Guide - Parts Index & Base Cabinet Section 1 150 325 DRAWER 870 870 870 73 73 720 720 DOOR 685 325 2 x
More information1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6 FOR INSTALLATION ASSISTANCE, CALL SARGENT AT 1-800-727-5477 www.sargentlock.com
More informationINSTRUCTIONS FOR 1431 Door Closer with Hold Open Arms 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
INSTRUCTIONS FOR Door Closer with Hold Open Arms SERIES ADJUSTABLE FROM SIZE THRU 6 FOR INSTALLATION ASSISTANCE CALL SARGENT AT -800-77-77 / www.sargentlock.com Installation Instructions based on Application
More informationSection 9: Finishing Touches - Other Decor Units
Section 9: Finishing Touches - Other Decor Units Butler Sink Units Important: This unit is designed to be used with either This unit is always used between other units. Level the units. Fix together and
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationREC Series Rack Installation Guide
REC Series Rack Installation Guide 1 REC Series Rack Installation Guide TABLE OF CONTENTS SECTION SAFETY WARNINGS 1 600 WIDE EXPLODED VIEW 2 800 WIDE EXPLODED VIEW 3 SWITCHING DOOR HANDING 4 STABILIZING
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationTRANSTHERM STUDIO INSTALLATION INSTRUCTIONS INTEGRATED STUDIO MODEL
TRANSTHERM STUDIO INSTALLATION INSTRUCTIONS INTEGRATED STUDIO MODEL Instructions for integration (fitting into cupboard with cupboard door in front of wine cabinet door) of Studio integrated model. Cabinet
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationSection 2. Profiles - How to use
Section s - How to use overview.... page 36 End larder profile - length 94mm/mm... page 37 Mid larder profile - length 94mm/mm... page 38 Worktop profile - length 3000mm.... page 39 Drawer profile - length
More informationEntry Level Assessment Blueprint Carpentry
Entry Level Assessment Blueprint Test Code: 4115 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Safety Demonstrate safe material handling practices Display comprehension of workplace/job-site
More information19-in. Mini-Rack Cabinet, Type 1
Spec-00466 19-in. DP FX (763) Mini-Rack 422-2588 422-2661 Cabinet, Components and Accessories Free-Stand Networking Cabinets 19-in. Mini-Rack Cabinet, Type 1 Industry Standards NEMA Type 1 EIA 310-D /
More informationProudly Manufactured in Australia by CTCI Pty Ltd
liberty PARTitiONing system installation guide Proudly Manufactured in Australia by CTCI Pty Ltd www.waterloosystems.com.au STEP 1 Mark out for wall channels to house partitions as per the supplied plan.
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationStandard Product. Free-Stand Cabinets 19-in. Mini-Rack Cabinet, Components and Accessories
Spec-00466 F763.422.2661 763.422.2588 Free-Stand Cabinets 19-in. Mini-Rack Cabinet, Components and Accessories Free-Stand Cabinets 19-in. Mini-Rack Cabinet, Components and Accessories 19-in. Mini-Rack
More informationPULLOUT SHELF ROCKLER BUILD IT WITH BUILD CUSTOMIZE
BUILD Stock Item 12229 Drawer s, 2 1 2" x 48" 63420 Baltic Birch Ply, 1/4" x 24" x 30" 38742 Maple, 3/4" x 3" x 24" 45953 100# Zinc Over-Travel Drawer Slides - Centerline 757-20" 30254 #8 x 1 1 4" Square
More informationFOLDING HARDWARE STARTEC T-SNAP G2/G4
FOLDING HARDWARE STARTEC T-SNAP G2/G4 T-SNAP G2 T-SNAP G4 Technical data: 40 kg for package throughout Height according 36+7 mm Fix bracket every 400 mm T-SNAP G2: 1x door leaf package T-SNAP G4: 2x door
More informationtable of contents Sliding Door Accessories Page Latches & Snuggers Stay Rollers Brackets & Stops
table of contents Square Track & Accessories Pages 4-7 Square Track Options Page 4 Light Duty Track Page 4 Square Track Brackets Page 5 Square Track Accessories Page 5 Square Track Trolleys Page 6-7 Offset
More informationVigilant Cigar Humidor Vault. Assembly Instructions
Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly
More informationSTANDARD 430E Series. Bottom mounted full extension drawer runners 430E E E E E E E E E4000
STANDARD 430E Series Bottom mounted full extension drawer runners Specifications Runner 430E8000 430E7500 430E7000 430E6500 430E6000 430E5500 430E5000 430E4500 430E4000 430E3500 430E3000 430E2500 Nominal
More informationCRL JACKSON 900 SERIES
INSTALLATION INSTRUCTIONS CRL JACKSON 900 SERIES FLOOR MOUNTED DOOR CLOSERS CENTER HUNG AND OFFSET crlaurence.com crlaurence.com MODEL No. 990 crlaurence.com Phone: (800) 421-6144 Fax: (800) 262-3299 crlaurence.com
More informationRef# Description Qty(pc) 14 Phillips Head Screw,M6*10, Black Flanged Lock Nut,M6,Black 48
Operator s Instructions GARAGE STORAGE SOLUTIONS WALL CABINET Model: GWC3DP SKU: 211-4359 Safety Instructions and Cautions Use appropriate safety equipment when using power and hand tools. Failure to do
More informationGE Monogram. Installation. Instructions. 27" Built-In Ovens. Models ZEK757WW ZEK757BW ZEK737WW ZEK737BW
GE Monogram Installation Instructions 27" Models ZEK757WW ZEK757BW ZEK737WW ZEK737BW CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT: Save these instructions
More informationSection 1. Kitchen installation. Base cabinets
Section 1 Kitchen installation Base cabinets Pre-build - Cabinet leg... page 16 Pre-build - Alternative cabinet leg... page 18 Pre-build - Cabinets.... page 19 Pre-build - Corner base cabinet centre upright
More informationHow to fit an Internal Door
How to fit an Internal Door How to fit an Internal Door The following instructions are for installing a internal door only. If you have any queries please contact Cheshire Mouldings technical helpline
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Special-Lite Restroom Partitions IMPORTANT - BEFORE YOU START... 1. Read through these installation instructions first to understand the order of work. 2. Check all components
More informationThe Castle House Assembly Instructions By Laser Dollhouse Designs
The Castle House Assembly Instructions By Laser Dollhouse Designs HOUSE PARTS First floor slots labeled 1A-1G First floor Walls labeled 1A-1G First floor interior door frames (4) Wall 1A frames (6) Main
More informationMonday, March 11, 13. Forcible Entry
Forcible Entry Forcible Entry Size-Up Consider Type of Emergency Try before you pry Forcible entry should create as little damage as possible Both speed and minimal damage are achieved through proficiency
More informationMighty Mo GX Series Cabinet Installation Guide. OR Rev /11
Mighty Mo GX Series Cabinet Installation Guide OR-71601787 Safety and Warning ATTENTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
More informationSection 8. Curved units. Curved units
Section 8 Curved units Curved units Curved corner post... page 94 Curved base cabinet... page 95 Curved wall cabinet... page 96 Curved deep wall cabinet... page 97 Curved plinth - Joining... page 99 www.howdens.com
More informationAC GATE TOOLS REQUIRED
AC 30988 GATE FOR USE WITH: PARADISE ISLE BRIDGE SYSTEM BS ENCLOSEB TOOLS REQUIRED Phillips head screwdriver Drill with 1/16 drill bit This gate is the final component of the Paradise Isle Bridge System.
More informationFabscan100 Assembly instructions v.1.00
Fabscan100 Assembly instructions v.1.00 Figure 1: The Fabscan100. Content: List of material 2 Assembly group 1: Turning Table 3 Assembly group 2: Camera/Laser Bracket 8 Assembly group 3: Housing 12 Final
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationBulk Storage Rack Assembly Instructions
Bulk Storage Rack Assembly Instructions Upright Frame Assembly Determine which end of the post goes up. The keystone slots on the front face of the post are wider at the top than at the bottom (see diagram
More informationwww.hafeleindia.com www.hafeleindia.com INTRODUCTION Intuitive furniture is the need of the hour. In times like these where every extra square meter is considered as good as gold, installing versatile
More informationHover. Installation Instructions. Raised Panel. Version
Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31
More informationAssembly Instructions
1 27694 Trend Podium Assembly Instructions #27694 Trend Podium Part Drawing Description Qty Part Drawing Description Qty P-1 Base 1 EA Hardware List Screw M6x12mm 30 EA P-2 Right Side Panel 1 EA A2 Phil
More informationKitchen Installation Manual
Kitchen Installation Manual June 2018 www.howdens.com 2 www.howdens.com Section pages Introduction... page 4 Supplied products... page 4 Guide - Hints and tips... page 5 Cabinet installation fittings...
More informationRECREATIONAL VEHICLE DOOR INSTALLATION INSTRUCTIONS
RECREATIONAL VEHICLE DOOR INSTALLATION INSTRUCTIONS PHILIPS PRODUCTS PHONE NUMBER: 574/296-0000 LIT-1614 2/01 REV 1 GENERAL ROUGH OPENING PREPARATION PROPER INSTALLATION IS ESSENTIAL FOR THE ACCEPTABLE
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationHotels Office Space Baths Barns Restaurants Galleries Lofts Kitchens Rustic Homes Closets Recessed Storage
Hotels Office Space Baths Barns Restaurants Galleries Lofts Kitchens Rustic Homes Closets Recessed Storage Flat Track Hardware by Leatherneck Hardware styling dates back to the turn of the century when
More informationSEMBLANCE MAIN MODULAR SYSTEM ASSEMBLY INSTRUCTIONS
SEMLANCE MODULAR SYSTEM MAIN ASSEMLY INSTRUCTIONS To view the Semblance assembly video, scan this code with a QR reader or visit http://www.bdiusa.com/semblance/ assembly.shtml DIUSA.COM TWO PERSON ASSEMLY
More informationSeries 8 Bifold door/shower wall
INSTALLATION GUIDE Series 8 Bifold door/shower wall Bifold Door Shower wall Corner Door NOTE: When the products is being used as a Bifold in a recess or with a side panel it can be used with or without
More informationChapter 23. Garage Construction
Chapter 23. Garage Construction 23.1 ESTABLISHING CHALK LINES 23.2 MEASURING AND CUTTING WALL PLATES 23.3 MARKING WINDOW & DOOR LOCATIONS ON EXTERIOR WALL PLATES 23.4 MARKING STUDS ON EXTERIOR WALL PLATES
More informationOrganisational Kitchen Fittings Kitchen Cabinet Accessories
Kitchen waste bin systems Single waste bin, capacity 1 litres Carcase width: Min. 400 mm For door mounting: For left and right hand use Installation: Screw fixing to side panel Housing: Steel, plastic
More informationGE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.
GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationAir-supply elements. Air-supply elements MGE Flanged plate (p. 5-3) M12-1/4" (p. 5-4) Longitudinal end connector (p.
Air-supply elements MGE 13.0 5-1 Air-supply elements 1 2 3 4 5 6 7 8 Flanged plate (p. 5-3) Connection piece (p. 5-4) Connection screw fitting -1/4" (p. 5-4) Longitudinal end connector (p. 5-5) 9 11 12
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary
More informationReplacement Guide. For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System RECOMMENDED TOOLS:
Replacement Guide For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System IMPORTANT: READ ENTIRE GUIDE BEFORE BEGINNING INSTALLATION. PLEASE NOTE: Proper assembly, installation
More informationInstallation Instructions for SHARP Built-in Kits model number RK-J40W/RK-J40K/RK-J40S/RK-J90W/RK-J90S
A9990,RK-J0W,J0K,J0S,J90S o/m Installation Instructions for SHARP Built-in Kits model number RK-J0W/RK-J0K/RK-J0S/RK-J90W/RK-J90S Before installing a Sharp Microwave Oven, read and check the following
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationParveneer Positive Pressure Fire Rated Frames Double rabbet with T stop for 20 minutes
Section P/J Page 1 Double rabbet with T stop for 20 minutes Smoke seals are installed in the frame, not the door Section P/J Page 2 Throated jamb with T stop for 20 minutes Smoke seals are installed in
More informationStorage Cabinets 9000 Series Assembly Instructions
Storage Cabinets 9000 Series Assembly Instructions Thank you for selecting Salsbury s storage cabinets. We are confident that the quality and construction of the cabinets will prove to be a good investment.
More informationCase Building Instructions For Derbywizard Freedom Aluminum Tracks
Case Building Instructions For Derbywizard Freedom Aluminum Tracks You can easily build a hard storage case for your new track by following these simple instructions. Materials Case Width (W): 2 ln = 8.75",
More informationUnit 9. Wall and Ceiling Framing
Unit 9 Wall and Ceiling Framing Wall construction Wall framing includes the assembly of horizontal and vertical members that make up exterior walls and interior partitions. Theses walls support the ceilings
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE,
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More informationLOWLINE SINGLE FOLD DOWN WALL BEDS
ASSEMBLY INSTRUCTIONS LOWLINE SINGLE FOLD DOWN WALL BEDS Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer Drill for Masonry) 6.5mm
More informationChapter 3. Wall Layout
GFCAHFH March 15, 2018 Construction Manual Version 18.0 Chapter 3. Wall Layout 3.1 LAYING OUT EXTERIOR WALLS 3.2 CUTTING EXTERIOR WALL PLATES 3.3 MARKING WINDOW AND DOOR LOCATIONS ON EXTERIOR WALL PLATES
More informationInstructions. for the installation of tamperpoof exterior screws. Kit KTPS-SM fits all modular Prodigy except EH222 and C2648
Kit KTPS-SM fits all modular Prodigy except EH222 and C2648 Screw Use Used 5-16 x ¾ truss head machine 4 bin to unit fasteners ¼ - 20 x ½ pan head machine 4 drain fitting(s) attachment, receiver bracket
More informationRSA GELANDEWAGEN DOUBLE REAR DOOR TRAY. FRONTRUNNEROUTFITTERS.COM should you have any queries. GET ORGANIZED. INSTALL TIME: 0.
GELANDEWAGEN DOUBLE REAR DOOR TRAY RSA VACC020 HINT Please consult FRONTRUNNEROUTFITTERS.COM should you have any queries. INSTALL TIME: 0.75 hours 1 GET ORGANIZED you will need: a Gelandewagen with double
More informationSection 7. Microwave/compact oven... page 185 Microwave/compact oven with warming drawer... page 187. Fridge or freezer option...
Section 7 Midi tower shelf configurations Cabinet information How the cabinet is supplied... page 176 Additional shelf pack... page 177 Cabinet modifications... page 177 Hints and tips for installation..........................................
More informationOVERVIEW You are installing 2 Major components: SITE PREP Remove organics
OVERVIEW You are installing 2 Major components: Dimensionally stable exterior frame with pre-drilled thread-bar holes. High yield thread-bar in a predetermined grid pattern (slab) and a heavy concentration
More informationseries 9500 top load bi4fold installation instructions
instructions Head Deflection (+0.12 / -0.00 ) Right Jamb Note: This is a top hung product. Provide adequate structure at head. Continuous threshold support is required. Left Jamb Head 4Lay bed of sealant
More informationThe following parts list is maintained for the UPI structural components.
4 PARTS LIST The following parts list is maintained for the UPI structural components. The product code consists of two four-digit parts: the first part refers to the product group and the second to the
More informationSelekta Pro 2000 Fast assembly hinges for office and commercial furniture
Fast assembly hinges for office and commercial furniture 99 The program opening angles 180 and 270 with pre-mounted pan-head screws with eccentric height adjustment ± 2 mm with eccentric overlay adjustment
More informationAdjustable Countertop Installation
Adjustable Countertop Installation Applies to Models: A1, A2, A3, A4, A5, & A6 Required Tools: Stud Finder, Level 1/4 deep well socket, Screwdrivers, Tape Measure, Drill and Drill Bits Language of origin:
More informationKitchen Fittings Hanging Cabinets and Accessories
Cabinet hanger Knock-in version, load bearing capacity 130 kg/pair Depth adjustment Finish: Galvanized Concealed mounting of cabinet hanger behind the rear panel (Min. 16 mm free space required) Mounting
More informationINSTALLATION MANUAL FORTRESS SERIES
Guardian Security Structures TEL 1-406-212-2334 EMAIL rg@gssdoors.com WEB www.gssdoors.com FORTRESS SERIES GENERAL INSTALLATION GUIDELINES 1. The door frame is installed using 16 bolt screws 7,5 mm in
More informationFactory Assistance: Phone: Fax: Page 1
CABLE RUNWAY ACCESSORIES Radius Drop / Stringer Drop Provides 3 bend radius Radius drop fits 6, 12 and 18 runway made from 1-1/2 x 3/8 tubing Steel construction Includes (3) cable spools, (1) bolt, (1)
More informationLeveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationInstallation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:
Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free
More informationInstallation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
More information1. Determine Home Design 2. Understand StoneSkirt TM Components 3. Perform StoneSkirt TM Installation
TM Steps for Installation: 1. Determine Home Design 2. Understand StoneSkirt TM Components 3. Perform StoneSkirt TM Installation Tools Needed Rubber mallet (2 lb. or heavier) Cordless drill with at least
More information" BASE CABINET
INSTALLATION GUIDE INSTALLATION GUIDE Before You Begin Installing Your Kitchen Cabinets 1. Read through installation guide to understand all steps and gather tools needed. 2. Verify that all of the hardware,
More information2300 BI-FOLD INSTALLATION GUIDE
2300 BI-FOLD INSTALLATION GUIDE INSTALLATION INSTRUCTIONS OF MAIN FRAME Header #8 x 2½ zinc coated screws 2 1 2 Jamb Jamb 1 1 3 #8 x 2½ zinc coated screws 4 1 4 3 #8 x 2½ zinc coated screws 5 Threshold
More informationRangerWare Fiberglass Door System Installation Instructions P/N
Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.
More informationSTOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets
Rev. 04 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS S-Type Network Cabinets -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench
More informationTABLETOP. Cut a 1/4" chamfer along front and back edges of each shelf (top side only).
PRTS tabletop boards/shelves - pine - (5) 3 /4" x 12" x 35 3 /4" B aluminum angles - (10) 3 /4" x 3 /4" x 3 /32" x 12" rear braces - maple - (2) 3 /4" x 2 1 /2" x 50" rear rails - maple - (2) 3 /4" x 2
More informationSystem 3000 specifications
System 3000 specifications Scope: Materials: Type of Bookstack: This specification covers delivery and installation of steel library shelving of the bracket type. Height, depth and accessories shall be
More informationThe DeWils Guide to Designer Series Framed Cabinetry Installation
The DeWils Guide to Designer Series Framed Cabinetry Installation www.dewils.com The first step in the cabinetry installation process is to prepare both yourself and the work areas for the new cabinets.
More informationPocket Shelter. Covered bike parking earns your site LEED credits.
Small and versatile, the Pocket Shelter stores bikes in areas that would not normally accommodate bike parking. This shelter is a modular system that provides covered and secure bike storage but is extremely
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More informationParamount Enclosure. Installation Guide
Paramount Enclosure Installation Guide Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 info@wrightline.com All products and company names are
More informationSTANDARD. Drawer runner program. Perfecting motion.
STANDARD Drawer runner program Perfecting motion STANDARD drawer runners Table of Contents Blum STANDARD drawer runners apply proven technology built upon years of experience to ensure a solid performance
More informationPinewood Derby Display Case
Pinewood Derby Display Case Optional Door Design by Neil Fern - Pack 187 Exterior Dimensions 23 ½ (H) X 10 ½ (W) X 3 ½ (D) Front Back OPTIONAL Door Finished Interior Dimensions 21 7/8 (H) X 9 (W) X 3 (D)
More informationRouter Table Floor Stand
Router Table Floor Stand Owner s Manual 05J20.40 Introduction The Veritas Router Table Floor Stand has been designed as a free-standing router table workstation to work with the existing Veritas Router
More informationwestern series 9500 f loor load The Volume Program window systems westernwindowsystems.com bi fold installation instructions
series 9500 f loor load bi fold The Volume Program Note: This is a bottom hung product. Provide adequate structure at threshold. Continuous threshold support is required. Right Jamb Head Deflection (+0.12
More informationBuilding an Elevated Garden Bed & Hydroponic Table
Building an Elevated Garden Bed & Hydroponic Table Materials: Lumber (2x4, 2x6, 1x4), Exterior Grade Wood Screws (2 1/2 & 1 5/8 ) and Hardware Cloth (enough to cover a 24 x48 area) Tools: Cordless Drill
More informationNon-Reinforced Joining Guide (Horizontal/Vertical)
Non-Reinforced Joining Guide (Horizontal/Vertical) for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationEaton Data Center Racks
Eaton Data Center Racks U 1. Product Overview In today's world, network equipment is one of the most important investments a business can make. How you store and protect this equipment is just as crucial.
More information