SEMBLANCE MAIN MODULAR SYSTEM ASSEMBLY INSTRUCTIONS

Transcription

1 SEMLANCE MODULAR SYSTEM MAIN ASSEMLY INSTRUCTIONS To view the Semblance assembly video, scan this code with a QR reader or visit assembly.shtml DIUSA.COM TWO PERSON ASSEMLY

2 Semblance System Your SEMLANCE System Furniture is engineered for easy assembly. Carefully follow this procedure to prevent any damage. Placement and Maintenance SEMLANCE System Furniture is designed for indoor use on level floors. Clean glass with glass cleaner, steel parts and wood veneer with a moist cloth. You will need: 32" Semblance Wall racket Template This Template helps locate the various positions of the second Wall racket. This is a leveling string to level the placement of your Wall rackets. 2

3 Locate the Package Reference ooklet See page 2 to identify all components. For missing hardware pieces, please contact DI Customer Service at customerservice@bdiusa.com. For all other concerns, please contact your DI Retailer. See page 3 for a representation of your Package containing critical information for its assembly. Component List J K x 4 L x 8 Wall racket Placement & Details Model Details in 9.3 cm to racket Template x2 Single Spacing TOP VIEW J K x L x A Package Reference C x 4 D x 4 Sample E x 4 E x 4 x 1 F x x 1 Overall Dimensions in 39.7 cm 100 in 254 cm Package Reference Sample Hole Spaces 4 G x 1 H x 1 x 1 I x 1 X x E x 4 Shelf & Cabinet Location 11 x 3 x 3 Cabinet racket J WALL SYSTEM PAGE 4 ROOM DIVIDER PAGE 10 SHELF ASSEMLY PAGE 14 CAINET ASSEMLY PAGE 17 3

4 WALL SYSTEM Assembly Sequence Overview F Level each Panel as it is being assembled. 4 Use Leveler Wrench (F) to adjust the height of the Panel, if necessary.

5 Plan Ahead. To plan unit placement, refer to Package Reference ooklet for critical dimensions.! The assembled unit CANNOT be moved, so carefully plan the placement of the unit prior to building. 1: See the racket Template spacing dimension on page 3 of the Package Reference ooklet. Using the provided spacing dimension, measure from the edge of where the left End Panel will be placed and mark the wall to indicate placement of the bracket template. Model Details x2 Single Spacing in 9.3 cm to racket Template TOP VIEW in 39.7 cm Hole Spaces in 254 cm Package Reference Sample 11 x 3 Cabinet racket J 5 2 Note: Future placement of left End Panel 3 WALL SYSTEM 5

6 2: Align the left side of the racket Template with the wall mark. Level the Template with the string, and insert Wall racket () into its designated groove. Mark the wall at bracket holes to locate fastener locations. 3: 4: Attach first racket to the wall using the appropriate attachment method illustrated below. C D H Sheet Rock: (C) Drywall Anchors () racket (D) Screws X D H Concrete/rick: (X) Plastic Concrete Anchors () racket (D) Screws A 1 /4" masonry drill bit and Power Drill is required for pilot holes. H Wooden eam: () racket (D) Screws D

7 5: Refer to Package Reference ooklet for the number of recommended Wall rackets. If 1 racket, skip to step 9 on page 8. Model Details in 9.3 cm to racket Template x2 Single Spacing TOP VIEW If 2 rackets, proceed to step and finish the Wall System section of the instructions in 39.7 cm 100 in 254 cm Package Reference Sample 4 Hole Spaces 11 x 3 : Use the racket spacing groove that is determined by your Package Reference ooklet (2 of 2), to locate the second racket. Cabinet racket J 5 3 WALL SYSTEM 7

8 7: Slip the Template over the attached racket (). Level the Template with the string and mark second racket hole locations on wall. 8: Refer to Step 4 on page to attach second racket () 9: ring Divider Panel up to racket () and slide Metal Insert (A) into racket with the long flange exposed as shown. Attach Metal Insert (A) to top of Panel with Screws (E). A 8

9 10: TOP VIEW 90 For next step turn to SHELF ASSEMLY PAGE 14 WALL SYSTEM 9

10 ROOM DIVIDER Assembly Sequence Overview F Level each Panel as it is being assembled. 10 Use Leveler Wrench (F) to adjust the height of the Panel, if necessary.

11 Plan Ahead. To plan unit placement, refer to Package Reference ooklet for critical dimensions.! The assembled unit CANNOT be moved, so carefully plan the placement of the unit prior to building. 1: Use the right edge of the racket Template to locate the right side of the attached End Panel. equal ROOM DIVIDER 11

12 2: Leveling the Template with the string, insert Wall racket () into designated groove. 3: Mark racket hole location on wall and mark the left edge of the Template on the wall. 4: Flip Template over and align right side of Template with wall mark to locate second racket position. Mark second racket hole location lightly on wall and then install racket. 12

13 5: Refer to Step 4 on page to attach both rackets. A E G A : ring End Panel up to attached racket () and slide Metal Insert (A) into racket () with the short flange exposed as shown. Attach Metal Insert (A) to top of Panel with Screws (E). 7: d Make sure the Panel s ends are the same distance from the wall. d TOP VIEW ROOM DIVIDER 13

14 SHELF ASSEMLY Model Details x2 Single Spacing in 9.3 cm to racket Template TOP VIEW in 39.7 cm Hole Spaces in 254 cm Package Reference Sample 1: Refer to Package Reference ooklet for the hole positions of the Shelf Screws (E). 11 x 3 Cabinet racket J 5 3 2: PANEL E SHELF PANEL SHELF 14

15 3: Use the appropriately sized Shelf Frame as a spacing guide for the next Panel. Lay the Frame on the floor beside the fixed Panel and bring the next Panel up to the Shelf Frame. Refer to the Package Reference ooklet for spacing of each set of Panels. 4: SHELF ASSEMLY 15

16 5: Slide Metal Insert (A) into attached racket () with the long flange exposed as shown. Attach Metal Insert (A) to top of Panel with Screws (E). : Gently tighten all Shelf Frames. A 7: Install Glass Shelves. Micro-etched face up. 1 SHELF ASSEMLY

17 CAINET ASSEMLY Model Details x2 Single Spacing 1: Refer to Package Reference ooklet for Cabinet racket positions in 39.7 cm in 9.3 cm to racket Template TOP VIEW in 254 cm Package Reference Hole Sample Spaces 2: Screw Cabinet rackets (J) into determined inserts. 11 x 3 Cabinet racket J 5 3 J L G CAINET ASSEMLY 17

18 3: Slide Cabinet in between panels, well above the racket, and carefully lower into place so that Cabinet racket fits into the recess on cabinet s bottom side. PANEL PANEL CAINET CAINET 18

19 4: K 5: L After completing the assembly of racketed Panels, repeat Shelf and Cabinet Assembly for each consecutive Panel until your Package is complete. CAINET ASSEMLY 19

20 *2. ADJUST DOOR HINGES (IF NEEDED) If the cabinet s door appears out of alignment, this can be corrected with minor adjustment on each door. ecause these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for adjustments to other elements. ut with a few adjustments, you can modify the orientation of the cabinet door to make sure that it hangs evenly * Use a Phillips screwdriver to adjust cabinet s door hinges: y adjusting Screw 1, the door will move LEFT or RIGHT within the frame. Make minor adjustments at both top and bottom hinges for best results. y adjusting Screw(s) 2, the door will move UP or DOWN within the frame (the top and bottom hinges must be adjusted the same degree). NOTE: Loosen Screws 2 one complete turn, raise or lower door, then hold in position while tightening Screws 2 (on both hinges). y adjusting Screw 3 the entire door will move IN or OUT, opening or closing the gap between the doorframe and cabinet. (This screw rarely needs adjustment.) A REVERSE DOOR-SWING (IF DESIRED) The Single Cabinets feature a reversible door assembly so that you can open either from the left or the right. To reverse the door s orientation, 1. Remove the Door by actuating both of its quick-release hinges (A); carefully place the detached Door aside. 2. Using a Philips head screwdriver, remove both Hinge Plates from the interior wall of the cabinet by loosening the screws holding it in place (). 3. Install both Hinge Plates to the opposite interior wall at the pre-determined locations. 4. Re-install the Door by connecting each Door Hinge to the relocated Hinge Plates. Helpful Tips for Designing your own Semblance Package. CAINET CAINET CAINET 7 inserts 3 inserts The Cabinet racket Screw must be 1 space hole above the Shelf Screw to align Cabinet bottom with the top of a Shelf. There is a 7 insert spacing pattern to align Shelves with top and bottom of a Cabinet. There is a 3 insert spacing pattern, from Cabinet racket to Shelf Frame, to align Shelves with middle of a Cabinet. 20 Designed by Matthew Weatherly. These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. DI are trademarks of ecker Designed, Inc. All Rights reserved. 2013, DI Assembled in the US from parts of foreign origin. REV01413v2