Features. Applications. Agency Approval. Mechanical and Physical Data. Maximum Ratings and Thermal Characteristics. Part Number Code SMDJ C A -
|
|
- Jasper Fitzgerald
- 5 years ago
- Views:
Transcription
1 Features Plastic package, excellent insulation strength. Glass passivated chip junction in SMC package. Excellent voltage clamping capability. Low Zener impedance. 3000W peak pulse power capability on 10/1000 s waveform. Typical leakage current less than 1 A above 13V. Very fast response time, typically less than 1.0ps from 0 volt to VBR minimum. High temperature soldering guaranteed: 265 C/10 sec. MSL: JEDEC-J-STD-020, Level 1 Applications I/O interface, VCC bus Telecom Industrial and consumer electronic applications. Relay and electromagnetic valve surge absorption. Agency Approval UL file no.: E TVS Diode SMDJ Series Mechanical and Physical Data Case: JEDEC SMC molded plastic. Surface mount device, solderable per MIL-STD-750, Method 2026 Polarity: Color band denoted cathode except bidirectional. Ratings and Thermal Characteristics Parameter Symbol Value Unit Peak Pulse Power Dissipation on 10/1000 s waveform (Note 1, Fig.1). PPPM Min 3000 Watt Peak Pulse of 10/1000 s waveform (Note 1, Fig.3). IPPM See Table Amp Steady State Power Dissipation at TL = 75 C, Lead lengths 0.375, (9.5mm) (Fig.5). PM(AV) 6.5 Watt Peak Forward Surge, 8.3 ms Single Half Sine Wave Superimposed on Rated Load (Note 2, Fig.6). IFSM 300 Amp Operating Junction and Storage Temperature Range. TJ, TSTG -55~150 C Note: 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25 C per Fig ms single half sine wave, or equivalent square wave, Duty cycle = 4 pulses per minutes maximum. Part Number Code SMDJ C A - Packaging Code (T13: Tape with 13 Reel; T7: Tape with 7 ) VBR Voltage tolerance (A: 5%; Blank: 10%) C: Bi-directional; Blank: Uni-directional Stand-Off Voltage or Typical Breakdown Voltage SMDJ Series (3000W) Page: 1 of 6
2 I-V Curve Characteristics PPPM VR VBR VC IR VF Peak Pulse Power Dissipation power dissipation Stand-off Voltage voltage that can be applied to the TVS without operation Breakdown Voltage voltage that flows through the TVS at a specified test current (IT) Clamping Voltage Peak voltage measured across the TVS at a specified IPPM (Peak Impulse ) Leakage measured at VR Forward Voltage Drop for Uni-directional Electrical Characteristics Breakdown Voltage Part Number Marking Stand Off VBR IT Voltage VR Uni Bi Uni Bi (V) Min. Max. Test IT (ma) Clamping Voltage VC IPP Peak Pulse IPP (A) Leakage IR ( VR SMDJ5.0A SMDJ5.0CA RDE DDE SMDJ6.0A SMDJ6.0CA RDG DDG SMDJ6.5A SMDJ6.5CA RDK DDK SMDJ7.0A SMDJ7.0CA PDM DDM SMDJ7.5A SMDJ7.5CA PDP DDP SMDJ8.0A SMDJ8.0CA PDR DDR SMDJ8.5A SMDJ8.5CA PDT DDT SMDJ9.0A SMDJ9.0CA PDV DDV SMDJ10A SMDJ10CA PDX DDX SMDJ11A SMDJ11CA PDZ DDZ SMDJ12A SMDJ12CA PEE DEE SMDJ13A SMDJ13CA PEG DEG SMDJ14A SMDJ14CA PEK DEK SMDJ15A SMDJ15CA PEM DEM SMDJ16A SMDJ16CA PEP DEP SMDJ17A SMDJ17CA PER DER SMDJ18A SMDJ18CA PET DET Page: 2 of 6
3 Breakdown Voltage Part Number Marking Stand Off VBR IT Voltage VR Uni Bi Uni Bi (V) Min. Max. Test IT (ma) Clamping Voltage VC IPP Peak Pulse IPP (A) SMDJ20A SMDJ20CA PEV DEV SMDJ22A SMDJ22CA PEX DEX SMDJ24A SMDJ24CA PEZ DEZ SMDJ26A SMDJ26CA PFE DFE SMDJ28A SMDJ28CA PFG DFG SMDJ30A SMDJ30CA PFK DFK SMDJ33A SMDJ33CA PFM DFM SMDJ36A SMDJ36CA PFP DFP SMDJ40A SMDJ40CA PFR DFR SMDJ43A SMDJ43CA PFT DFT SMDJ45A SMDJ45CA PFV DFV SMDJ48A SMDJ48CA PFX DFX SMDJ51A SMDJ51CA PFZ DFZ SMDJ54A SMDJ54CA PGE DGE SMDJ58A SMDJ58CA PGG DGG SMDJ60A SMDJ60CA PGK DGK SMDJ64A SMDJ64CA PGM DGM SMDJ70A SMDJ70CA PGP DGP SMDJ75A SMDJ75CA PGR DGR SMDJ78A SMDJ78CA PGT DGT SMDJ80A SMDJ80CA PGB DGB SMDJ85A SMDJ85CA PGV DGV SMDJ90A SMDJ90CA PGX DGX SMDJ100A SMDJ100CA PGZ DGZ SMDJ110A SMDJ110CA PHE DHE SMDJ120A SMDJ120CA PHG DHG SMDJ130A SMDJ130CA PHK DHK SMDJ150A SMDJ150CA PHM DHM SMDJ160A SMDJ160CA PHP DHP SMDJ170A SMDJ170CA PHR DHR SMDJ180A SMDJ180CA HHT IHT SMDJ190A SMDJ190CA HHV IHV SMDJ200A SMDJ200CA HHX IHX SMDJ220A SMDJ220CA HHE IHE SMDJ250A SMDJ250CA PHZ DHZ SMDJ300A SMDJ300CA PJE DJE SMDJ350A SMDJ350CA PJG DJG SMDJ400A SMDJ400CA PJK DJK SMDJ440A SMDJ440CA PJM DJM Note: 1. For bi-directional type having VR of 10 volts and less, the IR limit is double. Leakage IR ( VR Page: 3 of 6
4 Ratings and Characteristic Curves Fig 1 - Peak Pulse Power Rating Curve Fig 2 - Pulse Derating Curve Fig 3 - Pulse Waveform Fig 4 Typical Junction Capacitance Fig 5 Steady State Power Dissipation Derating Curve Fig 6 Non-Repetitive Forward Surge (Uni-directional Only) Page: 4 of 6
5 Marking Definitions PolyTrans Trade mark Lot No Marking Code Cathode Band (For Uni-directional product only) Physical Dimensions Dimension Millimeters Inches Min Max Min Max A B C D E F G H I J K L Lead Free Reflow Soldering Recommendations Preheat - Temperature Min (Ts_min) - Temperature Max (Ts_max) - Time (Ts_min to Ts_max) - Average Ramp-Up Rate Peak Temperature Time within 5ºC of actual Peak Temperature (tp) Ramp-Down Rate 150ºC 200ºC seconds 1~3ºC/second 260ºC max. 40 seconds max. 6 ºC /second max. Note: If the soldering temperatures exceed the recommended profile, devices may not meet the performance requirements. Page: 5 of 6
6 Packaging Information Part Number Packaging Code Component Package Quantity Packaging Option Packaging Specification SMDJ Series T13 DO-214AB 3000 Tape & Reel 16mm tape/13 reel EIA STD RS-481 SMDJ Series T7 DO-214AB 500 Tape & Reel 16mm tape/7 reel EIA STD RS-481 Tape and Reel Specifications Page: 6 of 6
Surface Mount Transient Voltage Suppressors (TVS)
Description The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
More informationTransient Voltage Suppressors. SMDJ Series. Circuit Protection System
Transient Voltage Suppressors SMDJ Series Features UNI Low profile package Matte tin lead free Plated Halogen free and RoHS compliant Low incremental surge resistance Typical IR less than 1µA above 12V
More informationTV30C5V0-G Thru. TV30C441-G Working Peak Reverse Voltage: 5.0 to 440 Volts Power Dissipation: 3000 Watts RoHS Device
TV35V-G Thru. TV344-G Working Peak : 5. to 44 Volts Power Dissipation: 3 Watts RoHS Device Features - Glass passivated chip. - 3W peak pulse power capability with a /µs waveform, repetitive rate (duty
More informationTV30C5V0-HF Thru. TV30C441-HF Working Peak Reverse Voltage: 5.0 to 440 Volts Power Dissipation: 3000 Watts RoHS Device Halogen Free
TV35V-HF Thru. TV344-HF Working Peak : 5. to 44 Volts Power Dissipation: 3 Watts RoHS Device Halogen Free Features - Glass passivated chip. - 3W peak pulse power capability with a /µs waveform, repetitive
More informationSMDJ-HR Series. Transient Voltage Suppression Diodes Surface Mount 3000W > SMDJ-HR Series. Description. Uni-directional
SMDJ-HR Series RoHS Pb e3 Uni-directional Bi-directional Description The SMDJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced
More informationATV30C5V0-HF Thru. ATV30C441-HF Working Peak Reverse Voltage: 5.0 to 440 Volts Power Dissipation: 3000 Watts RoHS Device Halogen Free
TV35V-HF Thru. TV344-HF Working Peak Reverse Voltage: 5. to 44 Volts Power Dissipation: 3 Watts RoHS Device Halogen Free Features - Ideally for surface mount applications. - Easy pick and place. - Plastic
More informationTransient Voltage Suppression Diodes Surface Mount 3000W > SMDJ-HR series. Bi-directional. Features V BR 3000 W 6.5 W 300 A 3.5 V.
RoHS Uni-directional Description Bi-directional The SMDJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More information3000W, 10V - 100V Surface Mount Transient Voltage Suppressor
3000W, 10V - V Surface Mount Transient Voltage Suppressor FEATURES Ideal for automated placement Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps Compliant
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
More informationSMDJ SERIES 3000 WATT TVS COMPONENT APPLICATIONS DO-214AB PACKAGE MECHANICAL CHARACTERISTICS FEATURES PIN CONFIGURATIONS
3000 WATT TVS COMPONENT APPLICATIONS Power Supply AC/DC Applications Telecom DO-214AB PACKAGE FEATURES UL File Recognition #E208219 IEC Compatibility 61000-4-2 (ESD) IEC Compatibility 61000-4-4 (EFT) IEC
More information5000W Surface Mount Transient Voltage Suppressor
5000W Surface Mount Transient Voltage Suppressor 5000W Surface Mount Transient Voltage Suppressor Features Stand-off voltage from 12 to 170 volts Glass passivated chip junction Low inductance Excellent
More informationFeatures. Applications. Agency Approval. Mechanical and Physical Data. Maximum Ratings and Thermal Characteristics. Part Number Code SMCJ C A -
Features Plastic package, excellent insulation strength. Glass passivated chip junction in SMC package. Excellent voltage clamping capability. Low Zener impedance. 1500W peak pulse power capability on
More informationomponents Marilla Street Chatsworth Watts
omponents 2736 Marilla Street Chatsworth!"# $%!"# 5.SMLJA THRU 5.SMLJ4A Features Halogen free available upon request by adding suffix "-HF" For surface mount application in order to optimize board space
More information5000W, 16V - 100V Surface Mount Transient Voltage Suppressor
5000W, 16V - 100V Surface Mount Transient Voltage Suppressor FEATURES 5000 watts peak pulse power capability at 10/1000μs waveform Ideal for automated placement Photo glass passivated junction Excellent
More informationICTE5.0 THRU ICTE15C SERIES
ICTE5.0 THRU ICTE15C SERIES TRANSZORB TRANSIENT VOLTAGE SUPPRESSOR Stand-off Voltage - 5.0 to 15 Volts Peak Pulse Power - Watts Case Style 1.5KE 1.00 (25.4) MIN. 0.205 (5.207) 0.190 (4.826) DIA. 0.375
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features Glass passivated junction Low zener impedance Excellent clamping capability 400W peak pulse power capability at 10/1000μs waveform, repetition rate (duty
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More informationSMCJ5.0CA Thru SMCJ170CA
Transient Suppressors TVS Diodes - 1500W > SMCJ Series SMCJ5.0CA Thru SMCJ170CA Description The SMCJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The 1.5SMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
More informationP4SMA-E Series. TVS Diodes Surface Mount 400W > P4SMA-E series Series. Description. Uni-directional
P4SMA-E Series RoHS Pb e3 Description The P4SMA-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationDATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY 1.0SMB series
Product specification November 5, 28 V. DATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY.SMB series RoHS compliant & Halogen free Transient Suppressors.SMB 2 Transient Suppressors (TVS) Data
More informationP6SMB Series. TVS Diodes Surface Mount 600W > P6SMB series. Description. Uni-directional
RoHS Pb e3 Uni-directional Description Bi-directional The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More informationP6SMB-E Series. TVS Diodes Surface Mount 600W > P6SMB-E series Series. Description. Uni-directional
P6SMB-E Series RoHS Pb e3 Description The P6SMB-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More information15KPA Series. Transient Voltage Suppression Diodes. Axial Leaded 15000W > 15KPA series. Descriptions. Uni-directional
5KPA Series RoHS Pb e3 Descriptions Uni-directional The 5KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationP4KE Series RoHS Pb e3
P4KE Series RoHS Pb e3 Description Bi-directional Uni-directional The P4KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More informationSales: Technical: Fax:
DATA SHEET Order code Manufacturer code Description 47-4344 n/a SMCJ33CA TVS DIODE BIDIRECTIONAL SMC (RC 47-4346 n/a SMCJ40CA TVS DIODE BIDIRECTIONAL SMC (RC 47-4290 n/a SMCJ5.0A TVS DIODE UNIDIRECTIONAL
More information5KP Series. Transient Voltage Suppression Diodes. Axial Leaded 5 kw > 5KP series. Description
5KP Series RoHS Pb e3 Description Uni-directional The 5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationTransient Voltage Suppression Diodes. Surface Mount 400W > P4SMA series. Features. less than 1μA when V BR. Applications. Additional Infomarion
P4SMA Series RoHS Pb e3 Uni-directional Bi-directional Description The P4SMA series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More information3KP Series. Transient Voltage Suppression Diodes. Axial Leaded 3000W > 3KP series. Description
3KP Series RoHS Pb e3 3/3/27 LFPCN2244 5KP Series Description Uni-directional The 3KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning
More information5KP-HRA Series. Transient Voltage Suppression Diodes Axial Leaded 5000W > 5KP-HRA series. Description. Uni-directional
5KP-HRA Series RoHS Pb e3 AGENCY Uni-directional Agency Approvals AGENCY FILE NUMBER E28662/E2353 Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) P PPM 5 W
More information30KPA-HRA Series. Transient Voltage Suppression Diodes Axial Leaded 30000W > 30KPA-HRA series. Descriptios. Uni-directional
3KPA-HRA Series RoHS Pb e3 AGENCY Uni-directional Agency Approvals Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) P PPM 3 W Steady State Power Dissipation
More informationP6SMB Series. Transient Voltage Suppression Diodes. Surface Mount 600W > P6SMB series. Description
P6SMB Series RoHS Pb e3 Description Uni-directional The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More informationTransient Voltage Suppression Diodes Axial Leaded 5000W > TP5KP series. Features. Bi-directional 5000 W 8.0 W 400 A 3.5 V. -55 to 150 C.
TP5KP Series RoHS Pb e3 Description The TP5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationDEVICES FOR BIPOLAR APPLICATIONS
SEMICONDUCTOR TECHNICAL SPECIFICATION GPP TRANSIENT VOLTAGE SUPPRESSOR 15 WATT PEAK POWER 5. WATTS STEADY STATE TVS 1.5KE SERIES FEATURES * Plastic package has underwriters laboratory certificate * Glass
More informationTransient Voltage Suppression Diodes Axial Leaded 1500W > TP1.5KE series. Features 1500 W 6.5 W 200 A 3.5 V. -55 to 150 C. -55 to 175 C 15 C/W 75 C/W
TP.5KE Series RoHS Pb e3 Description The TP.5KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More information6600W Transient Voltage Suppressor (TVS)
Description SM8S Series TVS diodes can be used in sensitive electronics protection against voltage transients induced by inductive load switching and lighting, especially for automotive load dump protection
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE SYMBOL IPPM P M(AV) I FSM T J, T STG
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 4 WATT PEAK POWER 1. WATTS STEADY STATE TVS P4FMAJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 4
More information5.0SMDJxxS Series, Single Chip Design
5.SMDJxxS Series, Single Chip Design RoHS Pb e3 Description The 5.SMDJxxS series, single chip design is designed specifically to protect sensitive electronic equipment from voltage transients induced by
More informationTP6KE Series. TVS Diodes Axial Leaded 600W > TP6KE series
TP6KE Series RoHS Pb e3 AGENCY Agency Approvals AGENCY FILE NUMBER E2353 Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) 6 W Steady State Power Dissipation
More informationSLD8S Series RoHS Pb e3
SLD8S Series RoHS Pb e3 Description The SLD8S Series TVS Diode is housed in a SMTO-263 package with lead modifications. It is designed to protect sensitive electronics against lightning and inductive load
More information500W Glass Passivated Junction Transient Voltage Suppressor. JEDEC DO-15 molded plastic body over passivated junction
Glass Passivated Junction Transient Voltage Suppressor SA5.0A -SA180CA 500W Glass Passivated Junction Transient Voltage Suppressor Features Stand-off voltage from 5.0 to 180 volts Glass passivated junction
More informationComchip 3KP-G Transient Voltage Suppressor Datasheet
Comchip 3KP-G Transient Suppressor Datasheet http://www.manuallib.com/comchip/3kp-g-transient-voltage-suppressor-datasheet.html Features -Glass passivated chip. -Low leakage. -Uni and Bidirection unit.
More informationTransient Voltage Suppression Diodes Axial Leaded 600W > P6KE series
Axial Leaded 6W > P6KE series RoHS Pb Description The is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 600 WATT PEAK POWER 5.0 WATTS STEADY STATE DEVICES FOR BIPOLAR APPLICATIONS
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 600 WATT PEAK POWER 5.0 WATTS STEADY STATE TVS SMBJ SERIES FEATURES * Peak pulse power:600 W (/00 μs),4 kw (8/20 μs) * Plastic package has underwriters laboratory
More informationP6SMB Transient Voltage Suppressor Diode Series
P6SMB Transient Voltage Suppressor Diode Series General Information The P6SMB series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping
More informationSMF Series. Transient Voltage Suppression Diodes. Surface Mount 200W > SMF Series. Description. Uni-directional
SMF Series RoHS Pb e3 Uni-directional Description The SMF series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 1500 WATT PEAK POWER 6.5 WATTS STEADY STATE
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 15 WATT PEAK POWER 6.5 WATTS STEADY STATE TVS TFMCJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 15
More informationP6KE-G Series. 600W Transient Voltage Suppressor. Stand-off Voltage: 6.8 ~ 600V Power Dissipation: 600 Watts RoHS Device. Features.
P6KE-G Series Stand-off Voltage: 6.8 ~ 6V Power Dissipation: 6 Watts RoHS Device Features -Plastic package has underwriters laboratory flammability classification 94V- -6W, surge capability at ms. -Excellent
More informationLCE Series. Transient Voltage Suppression Diodes. Axial Leaded 1500W > LCE series. Description. Uni-directional
Transient Suppression Diodes LCE Series RoHS Pb e3 Uni-directional Description The LCE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning
More informationSymbol Description Value Unit Conditions. Minimum 600
600W Surface Mount Transient Voltage Suppressor Features SMB Breakdown voltage from 6.8 to 250 volts Low inductance, excellent clamping capability Repetition rate(duty cycle): 0.01% Fast response time:
More informationTransient Voltage Suppression Diodes: P6SMB Series SMD Type 600 W
Features 1. For surface mounted applications 2. RoHS compliant and halogen-free 3. Reliable low cost construction utilizing molded plastic technique 4. Glass passivated chip junction 5. Both bi-directional
More informationDEVICES FOR BIPOLAR APPLICATIONS. For Bidirectional use C or CA suffix for types 3KP5.0 thru 3KP110 Electrical characteristics apply in both direction
TVS 3KP SERIES GPP TRANSIENT VOLTAGE SUPPRESSOR 3 WATT PEAK POWER 8. WATTS STEADY STATE FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 3 watt surage capability
More informationSLD Series. TVS Diodes. Axial Leaded 2200W > SLD series. Description
SLD Series RoHS Pb e3 Description AGENCY Agency Approvals AGENCY FILE NUMBER E2353 Ratings and Thermal Characteristics (T A =25 O C unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE SYMBOL IPPM P M(AV) I FSM. I 2 t 6.64 A 2 /Sec T J, T STG
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 4 WATT PEAK POWER 1. WATTS STEADY STATE TVS P4FMAJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 4
More informationSMF4L Series. TVS Diodes Surface Mount 400W > SMF4L Series. Description. Uni-directional
SMF4L Series RoHS Pb e3 Uni-directional Description The SMF4L series of SOD-123FL small and flat lead lowprofile plastic package is designed specifically to protect sensitive electronic equipment from
More informationGPP TRANSIENT VOLTAGE SUPPRESSOR 3000 WATT PEAK POWER 7.5 WATTS STEADY STATE SYMBOL. W Steady State Power Dissipation at T L = 75 O C P M(AV) I FSM
GPP TRANSIENT VOLTAGE SUPPRESSOR 3 WATT PEAK POWER 7.5 WATTS STEADY STATE TVS 3KPSMC SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction *3 watt surage capability
More informationChina - Germany - Korea - Singapore - United States - smc-diodes.com
TRANSIENT SUPPRESSOR Features DO-15 Glass Passivated Die Construction 600W Peak Pulse Power Dissipation 5.8V- 376V Standoff Voltage Uni- and Bi-Directional Versions Available Excellent Clamping Capability
More informationSurface Mount Transient Voltage Suppressors
TVS diodes can be used in a wide range of applications which like consumer electronic products, automotive industries, munitions, telecommunications, aerospace industries, and intelligent control systems.
More informationTransient Voltage Suppression Diodes Surface Mount 600W > TPSMA6L Series 3 W 60 A 3.5V V. -65 to 150 C 35 C/W 200 C/W. Anode
Surface Mount 6W > RoHS Description Uni-directional The is designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events,
More informationP-600. Mechanical Dimensions:In Inches (mm) China - Germany - Korea - Singapore - United States - smc-diodes.
Features: Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass Passivated Junction 15000W Peak Pulse Power Capability on 10/1000 μs waveform Voltage-17.0 to 280 Volts Excellent
More informationSMA6L Series. Transient Voltage Suppression Diodes. Surface Mount 600W > SMA6L series
SMA6L Series RoHS Pb e3 Uni-directional Description The SMA6L series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More information20KW Transient Voltage Suppressor 20KPA20A 20KPA300CA. 20KW Transient Voltage Suppressor. Features. Mechanical Data
Features Glass passivated junction 20KW peak pulse power capability at 10/1000μs waveform repetition rate (duty cycles): 0.01% Fast response time: typically less than 1.0ps from 0v to VBR min. Excellent
More informationTransient Voltage Suppression Diodes Axial Leaded 500W > SA series
Axial Leaded 5W > SA series RoHS b Description The is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Agency
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The SMF series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional Compatible
More information5KP Series 5000 Watt Axial Leaded Transient Voltage Suppressor
5KP Series 5000 Watt Axial Leaded Transient Voltage Suppressor Description The 5KP Series are designed specifically to protect sensitive Uni-directional electronics equipment from voltage transients induced
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
Compliant 15,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This device clamps dangerous high-voltage short-term transients such as those produced by the secondary effects of
More informationFAIRCHILD TVS Is Now Part of
FAIRCHILD TVS Is Now Part of To learn more about Taiwan Semiconductor, please visit our website at www.taiwansemi.com Please note: The acquisition of this portfolio aligns with our strategy to expand in
More informationSMBJ5.0 THRU SMBJ440CA
SMBJ5.0 THRU SMBJ440CA SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Stand-off : 5.0-440 Volts Peak pulse power: 600 Watts 0.087 (2.20) 0.071 (1.80) 0.096(2.44) 0.084(2.13) SMB/DO-214AA 0.180(4.57) 0.160(4.06)
More informationSurface Mount Transient Voltage Suppressor Stand-Off Voltage to 180 Volts 200 Watt Peak Pulse Power
Features Surface Mount Transient Suppressor Stand-Off - 5.0 to 80 olts 0 Watt Peak Pulse Power For surface mounted applications in order to optimize board space Low profile package Built-in strain relief
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Glass passivated junction Low inductance Excellent clamping capability
More informationINPAQ. Specification. Product Name Power TVS (Transient Voltage Suppressor) Series Package Size. SMDJ-T Series SMD(DO214-AB)
SMDJ-T Series Specification Product Name Power TVS (Transient Voltage Suppressor) Series Package Size SMDJ-T Series SMD(DO214-AB) SMDJ-T Series Engineering Specification 1. FEATURES 3000W Surface Mount
More informationDO-15 China - Germany - Korea - Singapore - United States - smc-diodes.com
P6KE SERIES TRANSIENT VOLTAGE SUPPRESSOR Features: Glass Passivated Die Construction 600W Peak Pulse Power Dissipation 6.8V- 440V Standoff Voltage Uni- and Bi-Directional Versions Available Excellent Clamping
More information30KP SERIES. Features. Mechanical Data. Maximum Ratings and Electrical A =25 C unless otherwise specified
3KP SERIES 3W TRANSIENT VOLTAGE SUPPRESSOR Pb Features Glass Passivated Die Construction 3W Peak Pulse Power Dissipation 8V 88V Standoff Voltage A B A Uni- and Versions Available Excellent Clamping Voltage
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Glass passivated junction Low inductance Excellent clamping capability
More informationM C C. SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A. Features. Transient Voltage Suppressor 6.8 to 550 Volts 1500 Watt.
omponents 20736 Marilla Street Chatsworth!"# $%!"# SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A Features For surface mount applicationsin in order tooptimize board space Lead Free Finish/Rohs Compliant (Note1)
More information1.5SMC6.8AT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMC6.8AT3G. Bi-directional. Cathode. Anode. Uni-directional. Description
1.5SMC6.8AT3G Pb Description The 1.5SMC6.8AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More information1N4740A - 1M200Z. RoHS. Features
Pb RoHS COMPLIANCE N474A - M2Z CREAT BY ART. Watt Glass Passivated Junction Silicon Zener Diodes DO-4 Features Low profile package Built-in strain relief Glass passivated junction Low inductance Typical
More informationSurface Mount > 600W > P6SMB11AT3G Series. Description. Features
P6SMB11AT3G Series Pb OBSOLETE/EOL DATE June/30/2018 PCN/ECN# LFPCN41246 REPLACED BY P6SMB Series Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage,
More informationTransient Voltage Suppression Diodes: SMAF Series SMD Low Profile Type 400 W
Features 1. Low profile and space saving 2. RoHS compliant and halogen-free 3. Reliable low cost construction utilizing molded plastic technique 4. Glass passivated chip junction 5. Both bi-directional
More informationChina - Germany - Korea - Singapore - United States - smc-diodes.com
Technical Data Features: Glass Passivated Die Construction 5000W Peak Pulse Power Dissipation Uni- and Bi-Directional Versions Available Excellent Clamping Capability Fast Response Time Plastic Case Material
More information1N4740A - 1M200Z. RoHS. Features
Pb RoHS COMPLIANCE N474A - M2Z CREAT BY ART. Watt Glass Passivated Junction Silicon Zener Diodes DO-4 Features Low profile package Built-in strain relief Glass passivated junction Low inductance Typical
More informationSMAJ5.0A THRU SMAJ300CA SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR
SMAJ5.0A THRU SMAJ300CA SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Features SMA Glass Passivated Die Construction 400W Peak Pulse Power Dissipation 5.0V- 300V Standoff Voltage Uni- and Bi-Directional Versions
More informationChina - Germany - Korea - Singapore - United States - smc-diodes.com
SMCJ SERIES SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Features: Glass Passivated Die Construction 1500W Peak Pulse Power Dissipation 5.0V- 170V Standoff Voltage Uni- and Bi-Directional Versions Available
More informationUnidirectional* PLASTIC SURFACE MOUNT ZENER OVERVOLTAGE TRANSIENT SUPPRESSORS VOLTS 400 WATTS PEAK POWER
Unidirectional* The SMA series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability, low zener impedance
More informationTransient Voltage Suppression Diodes Surface Mount 600W > SMBJ-HR series. Bi-directional. Features 5.0 W 100 A 3.5V/5.0 V. -55 to 150 C 20 C/W
SMBJ-HR Series RoHS Uni-directional Description TVS Diode Arrays (SPA Family of Products Bi-directional The SMBJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment
More information5.0SMDJ Transient Voltage Suppressor Diode Series
*RoHS OMPLINT eatures n RoHS compliant* and halogen free** n Surface mount SM package n Standoff voltage: 5 to 7 volts n Peak Pulse Power: 5 watts n Typical temperature coefficient: V R =. % x VR @ 25
More informationFAIRCHILD TVS Is Now Part of
FAIRCHILD TVS Is Now Part of To learn more about Taiwan Semiconductor, please visit our website at www.taiwansemi.com Please note: The acquisition of this portfolio aligns with our strategy to expand in
More informationACZRA4728-HF Thru. ACZRA4764-HF
CZR4728-HF Thru. CZR4764-HF Voltage: 3.3 to Volts Power:. Watts RoHS Device Halogen Free Features -Batch process design, excellent power dissipation offers better reverse leakage current and thermal resistance.
More information30KP Series 30000W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR R-6 PACKAGE WILLAS ELECTRONIC CORP. R-6 (Cathode band Only Uui-polarity product)
3W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR 3KP Series 1.(25.4)MIN..36(9.14).338(8.6) 1.(25.4)MIN. R-6 (Cathode band Only Uui-polarity product).52(1.32).47(1.2) Dimensions in inches and (millimeters) DIA..36(9.14).338(8.6)
More information1KSMB Series. Transient Voltage Suppression Diodes. Surface Mount 1000W > 1KSMB series. Uni-directional. Description
Surface Mount W > KSMB series KSMB Series RoHS Pb e3 Uni-directional Description Bi-directional The KSMB series is designed specifically to protect sensitive electronic equipment from voltage transients
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. P6KE6V8(C)A - P6KE4(C)A 6W TRANSIENT VOLTAGE SUPPRESSOR Features 6W Peak Pulse
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
M1KP22A M1KP280CA(e3) Available 1,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This Transient Voltage Suppressor series of M1KP22A M1KP280CA offers an extended voltage range
More informationGLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt DEVICES FOR BIPOLAR APPLICATIONS
GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt BREAK DOWN VOLTAGE 6.8 to 550 Volt FEATURES Recongnized File # E210467 Plastic package has Underwriters Laboratory Flammability Classification
More informationSurface Mount > 400W > 1SMA5.0AT3G Series. Description. Features
SM5.0T3G Series Pb OBSOLETE/EOL DTE June/30/208 PCN/ECN# LFPCN4246 REPLCED BY SMJ Series Description The SM5.0T3G series is designed to protect voltage sensitive components from high voltage, high energy
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationP6SMB11AT3G Series. TVS Diodes. Surface Mount > 600W > P6SMB11AT3G Series. Bi-directional. Cathode. Anode. Uni-directional.
P6SMB11AT3G Series Pb Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationCZRA4728-G Thru CZRA4764-G
CZR4728-G Thru CZR4764-G Voltage: 3.3 to Volts Power:. Watts RoHS Device Features -Batch process design, excellent power dissipation offers better reverse leakage current and thermal resistance. -Standard
More information