HCD-GRX2/RX33 SERVICE MANUAL. MINI Hi-Fi COMPONENT SYSTEM. US Model Canadian Model. E Model Australian Model HCD-GRX2 SPECIFICATIONS HCD-RX33

Transcription

1 HCD-GRX2/RX33 SERVCE MANUAL US Model Canadian Model HCD-RX33 E Model Australian Model HCD-GRX2 HCD-GRX2/RX33 is the tuner, deck, CD and amplifier section in MHC-GRX2/RX33. Photo : HCD-GRX2 CD SECTN TAPE DECK SECTN Model Name Using Similar Mechanism CD Mechanism Type Base Unit Type ptical Pick-up Type Model Name Using Similar Mechanism Tape Transport DECK-A Mechanism Type DECK-B HCD-G101 CX3 KSM-213BCM KSS-213B/S-N HCD-G101 TK20FX-SW TK20FX-SW SPECFCATNS AUD PWER SPECFCATNS: (U.S.A. model only) PWER UTPUT AND TTAL HARMNC DSTRTN: with 6 Ω loads both channels driven, from 70 20,000 Hz; rated 25 W per channel minimum RMS power, with no more than 0.9% total harmonic distortion from 250 mw to rated output. Amplifier section North American model Continuous RMS power output 35 W 35 W (6 Ω at 1 khz, 10% THD) ther models The following measured at AC 110, 220 V 60 Hz; DN power output (Rated) 25 W 25 W (6 Ω at 1 khz, DN) Continuous RMS power output (Reference) 30 W 30W (6 Ω at 1 khz, 10% THD) The following measured at AC 120, 240 V 60 Hz; DN power output (Rated) 30 W 30 W (6 Ω at 1 khz, DN) Continuous RMS power output (Reference) 35 W 35W (6 Ω at 1 khz, 10% THD) Peak music power output (Reference) 400 W utputs PHNES (stereo phone jack) : accepts headphones of 8 Ω or more SPEAKER : accepts impedance of 6 to 16 Ω CD player section System Laser Laser output Frequency response Wavelength Tape deck section Recording system Frequency response Compact disc and digital audio system Semiconductor laser (λ = 780 nm) Emission duration: continuous Max µw* *This output is the value measured at a distance of 200 mm from the objective lens surface on the ptical Pick-up Block with 7 mm aperture. 20 Hz 20 khz (± 0.5 db) nm 4 -track 2 -channel stereo 60 13,000 Hz (± 3dB), using Sony TYPE Ι cassette Continued on next page MN Hi-Fi CMPNENT SYSTEM MCRFLM

2 SERVCNG NTE Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range Antenna Antenna terminal ntermediate frequency MHz FM lead antenna 75 Ω unbalanced 10.7MHz AM tuner section Tuning range European, Australian and South African models: 531 1,602 khz ther models: 530 1,710 khz Antenna AM loop antenna Antenna terminals External antenna terminal ntermediate frequency 450 khz General Power requirements Mexican model: 120 V AC, 50/60 Hz Australian and South African models: V AC, 50/60 Hz ther models: 120V AC, 60Hz Power consumption 80 W Dimensions (w/h/d) incl. projecting parts and controls Approx mm (11 1 / / /8 in) Mass Approx. 7.2 kg (15 lb 14 oz.) Supplied accessories: AM loop antenna (1) Remote RM-SG5 (1) FM lead antenna (1) NTES N HANDLNG THE PTCAL PCK-UP BLCK R BASE UNT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NTES N LASER DDE EMSSN CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Design and specifications are subject to change without notice. CAUTN Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRDUCT MARKNG is located on the rear exterior. This caution label is located inside the unit. SAFETY-RELATED CMPNENT WARNNG!! CMPNENTS DENTFED BY MARK! R DTTED LNE WTH MARK! N THE SCHEMATC DAGRAMS AND N THE PARTS LST ARE CRTCAL T SAFE PERATN. REPLACE THESE CMPNENTS WTH SNY PARTS WHSE PART NUMBERS APPEAR AS SHWN N THS MANUAL R N SUPPLEMENTS PUBLSHED BY SNY. ATTENTN AU CMPSANT AYANT RAPPRT À LA SÉCURTÉ! LES CMPSANTS DENTFÉS PAR UNE MARQUE! SUR LES DAGRAMMES SCHÉMATQUES ET LA LSTE DES PÈCES SNT CRTQUES PUR LA SÉCURTÉ DE FNCTNNEMENT. NE REMPLACER CES CMPSANTS QUE PAR DES PÈSES SNY DNT LES NUMÉRS SNT DNNÉS DANS CE MANUEL U DANS LES SUPPÉMENTS PUBLÉS PAR SNY. 2

3 SAFETY CHECK-UT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 ma (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 µf 1.5 kω Earth Ground AC Voltmeter (0.75 V) Fig. A. Using an AC voltmeter to check AC leakage. TABLE F CNTENTS 1. GENERAL DSASSEMBLY 2-1. CD Door CD Mechanism Deck Front Panel Main Board and H.P Board CD Tray CD Decoder Board Base Unit Cassette Lid (L)/(R) MECHANCAL ADJUSTMENTS ELECTRCAL ADJUSTMENTS DAGRAMS 5-1. Circuit Boards Location Brock Diagrams Deck Section Tuner/CD Section C Brock Diagrams Schematic Diagram Main Section Printed Wiring Board Main Section Printed Wiring Board CD Section Schematic Diagram CD Section Schematic Diagram Panel Section Printed Wiring Board Panel Section C Pin Function EXPLDED VEWS 6-1. Cabinet Section Front Panel Section Cassette Button Section Cassette Mechanism Deck Section CD Mechanism Deck Section CD Mechanism Deck Section Base Unit Section (KSM-213BCM) ELECTRCAL PARTS LST

4 SECTN 1 GENERAL LCATN F PARTS AND CNTRLS ! 9 @ 1 Disc tray 2 DSC 1 button 3 DSC 2 button 4 DSC 3 button 5 DSC SKP button 6 PEN/CLSE button 7 DBFB button 8 VLUME knob 9 Display window!º CLCK TMER SET button! TMER N/FF button! DSPLAY DEM! TUNER/BAND! (play/pause) button! ENTER/NEXT button! ± CD AMS/TUNER PRESET TMER SET buttons! FLE SELECT! /u (PWER) button!ª TUNER MEMRY REPEAT EDT STERE/M N, PLAY MDE TAPE π (STP) 0 ) CD/TUNER PHNES Deck A, Deck B, Tape operaying buttons r (recording) ( (play) 0 (fast rening) ) (fast forward) p 6 (stop/eject) P (pause) 4

5 SECTN 2 DSASSEMBLY Note : Follow the disassembly procedure in the numerical order given CD DR 2 CD door Two craws 1 Pull out the CD tray and remove the CD door with releasing claws into the direction of arrow CD MECHANSM DECK 1 Two screws (B 3 8) 6 CD mechanism deck 4 Flat type wire (CN09) 5 Harness (CN302) 2 Screw (PTPWH 3 10) 3 Two screws (BVTP 3 10) 2 Screw (PTPWH 3 10) 5

6 2-3. FRNT PANEL 3 Screw (BVTP 3 10) 4 Screw (BVTP 3 10) 5 Two screw (BVTP 3 10) 6 Two screws (BVTP 3 10) 7 Screw (PTPWH 3 10) 1 Connector (CN401) 9 Front panel 7 Screw (PTPWH 3 10) 8 Screw (BVTP 3 10) HW T SET THE PWER CRD 2 Three screws (BVTP 3 10) power cord 2-4. MAN BARD AND H.P BARD 3 Connector 2 Harness (CN204) 4 Connector (CN202) 1 Harness (CN303) 8 H.P board 5 Connector (CN201) 7 MAN board 6 Two screws (KTP 3 8) Craw 6

7 2-5. CD TRAY 1 Screw (P 2.6 4) 2 Bracket 5 Flat type wire (CN06) 3 Screw (P 2.6 4) 4 Bracket 6 CD tray 2-6. CD DECDER BARD 1 Two screws (BVTP 3 10) 6 Flat type wire (CN06) 5 Flat type wire (CN01) 7 CD DECDER board 8 Two screw (BVTP 3 10) 9 Sheet 4 Connector (CN05) Craw Craw!º Connector (CN03) Two craws 3 Belt 2 Two screws (BVTP 3 10) 7

8 2-7. BASE UNT 4 Screw (PTPWH 2.6 8) 2 Screw (PTPWH 2.6 8) 5 UD-Cam 3 UD-gear 7 Spring 6 Spring 8 Spring 9 Base unit 1 Two screws (KTP 3 8) 2-8. CASSETTE LD (L) / (R) 1 Cassette lid (L) Four craws Four craws 2 Cassette lid (R) 8

9 SECTN 3 MECHANCAL ADJUSTMENTS Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback head pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement Torque FWD FWD back tension FF/REW Torque meter CQ-102C CQ-102C CQ-201B Meter reading 40 to 70 g cm ( oz inch) 1 to 5 g cm ( oz inch) 55 to 140 g cm ( oz inch) SECTN 4 ELECTRCAL ADJUSTMENTS DECK SECTN 1. Demagnetize the record/playback head with a head damagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjusted. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and R- CH. Tape P-4-A100 WS-48B 0 db=0.775v Signal 10 khz, 10 db 3 khz, 0 db Record/Playback Head Azimuth Adjustment (Deck A, Deck B) Note: Perform this adjustments for both decks. Used for Azimuth Adjustment Tape Speed Adjustment Procedure: 1. Mode : Playback test tape P-4-A100 (10kHz, 10dB) SPEAKER terminal (JK501) level meter set 9

10 2. Turn the adjustment screw and check output peaks. f the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 2 db of peak. 4. After the adjustments, apply suitable locking compound to the parts adjusted. Adjustment Location: Remove the cassette lid before adjustment (See page 8) L-CH peak output level within 2dB within 2dB screw position R-CH peak L-CH peak R-CH peak screw position Adjustment screws REC/PB head (deck A) or PB head (deck B) 3. Mode: Playback Tape Speed Adjustment (Deck A) test tape P-4-A100 (10kHz, 10dB) SPEAKER terminal (JK501) (L-CH) L oscilloscope Procedure: 1. Mode: Playback test tape WS-48B (3kHz, 0dB) frequency counter set R set SPEAKER terminal (JK501) (R-CH) Waveform of oscilloscope in phase good wrong SPEAKER terminal (JK501) 2. Adjust the SFR201 so that the frequency counter reads 3,000 Hz ± 90Hz. Adjustment Location: MAN board Sample Value of Wow and flutter W. RMS (JS) within 0.3% (test tape: WS-48B) [MAN BARD] Component side Tape Speed SFR201 CN204 10

11 TUNER SECTN 0 db=1µv AM Tuning Voltage Adjustment Main board TP1 F G VT DC voltmeter Procedure: 1. Set the reception frequency of the unit to 530 khz. 2. Adjust L105 for 1.2 ± 0.05 V reading on the DC voltmeter. 3. Set the reception frequency of the unit to 1,710 khz. 4. Confirm that the voltage reading on the DC voltmeter is within 8.0 ± 0.5 V. Adjustment Location: MAN board (See page 12) AM Tracking Adjustment loop antenna loop antenna (Supplied accessories) AM RF SSG set 30% amplitude AM ANTENNA 60 cm terminal (TM1) modulation by 400 Hz signal Field strength db (µv/m) =SSG output level db (µv/m) 26 db. Procedure: 1. Tune the set to 600 khz. 2. Set the output of AM RF SSG so that the input level of the set will become 60 db (µv/m). 3. Adjust L104 so that when the waveform on the oscilloscope is maximum, no noise appears. 4. Tune the set to 1,400 khz. 5. Adjust TC102 so that when the waveform on the oscilloscope is maximum, no noise appears. Repeat the procedures in each adjustment several times, and the tracking adjustment should be finally done by the trimmer capacitors. Adjustment Location: MAN board (See page 12) FM Tuning Voltage Adjustment Main board TP1 F G VT DC voltmeter Procedure : 1. Set the reception frequency of the unit to 87.5 MHz. 2. Adjust L103 for 1.2 ± 0.05V reading on the DC voltmeter. 3. Set the reception frequency of the unit to 108 MHz. 4. Confirm that the voltage reading on the DC voltmeter is within 7.8 ± 0.5V. Adjustment Location: MAN board (See page 12) 11

12 FM Tracking Adjustment FM Tuned Level Adjustment Procedure: FM RF SSG oscilloscope FM RF SSG 75 Ω coaxial set SPEAKER terminal (JK501) FM ANTENNA terminal (JK101) Carrier frequency : 90 MHz, 106 MHz Modulation : AUD 1kHz, 75kHz deviation (100%) utput level : 20 db (at 75 Ω open) 1. Tune the set to 90 MHz. 2. Adjust L102 so that when the waveform on the oscilloscope is maximum, no noise appears. 3. Tune the set to 106 MHz. 4. Adjust TC101 so that when the waveform on the oscilloscope is maximum, no noise appears. Carrier frequency : 98 MHz Modulation : AUD 1 khz, 75 khz deviation (100%) utput level : 28 db (at 75 Ω open) Procedure: 1. Supply a 28 db 98 MHz signal from the ANTENNA terminal. 2. Tune the set to 98 MHz. 3. Adjust SFR101 to the point (moment) when the TUNED indicator will change from going off to going on. Adjustment Location: MAN board set FM ANTENNA terminal (JK101) Repeat the procedures in each adjustment several times, and the tracking adjustment should be finally done by the trimmer capacitors. Adjustment Location: MAN board Adjustment Location [MAN BARD] Component side JK501 C103 FM Tuned Level SFR101 C102 TP1 L105 AM Tuning Voltage C101 L103 TC102 L104 L102 TC101 JK101 AM Tracking FM Tracking FM Tuning Voltage 12

13 CD SECTN Note: 1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc ( ) unless otherwise indicated. 3. Use an oscilloscope with more than 10MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Adjust the focus bias adjustment when optical block is replaced. Focus Bias Adjustment CD DECDER board CN12 FE VC DC voltmeter Procedure: 1. Connect DC voltmeter to test point CN12 (FE), (VC) on CD DECDER board. 2. Turned Power switch on. 3. Put disc (YEDS-18) in and stop. 4. Adjust VR01 so that the DC voitmeter reading is 0 ± 20 mv. RF Level Check CD DECDER board TP (RF) CN12 (VC) oscilloscope Procedure : 1. Connect oscilloscope to test point TP (RF) on CD DECDER board. 2. Turned Power switch on. 3. Put disc (YEDS-18) in and playback. 4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not. Note: Clear RF signal waveform means that the shape can be clearly distinguished at the center of the waveform. VLT/DV: 200 mv TME/DV: 500 ns 0.3 level: 1.0 Vp-p 0.2 Adjustment Location: CD DECDER board Adjustment Location: CD DECDER board Focus Gain Adjustment (VR02) This gain has a margin, so even if it is slightly off. There is no problem. Therfore, do not perform this adjusment. Please note that it should be fixed to mechanical center position when you moved and do not know original position. Adjustment Location [CD DECDER BARD] Component side Focus Gain CN12 C03 VR02 C01 VR01 R07 RF Level Focus Bias 13

14 SECTN 5 DAGRAMS 5-1. CRCUT BARDS LCATN DSK board SW (C) board SW (D) board SW (B) board MTR (6P) (S) board MTR board CD DECDER board SW (A) board PANEL board SENSR board MAN board H.P board R/P SWTCH board AC PWER board VR board 14

15 HCD-GRX2/RX BLCK DAGRAMS DECK SECTN TAPE B HP901 PB HEAD TAPE A HRP901 REC/PB HEAD HE901 ERASE HEAD R CH R CH Q203, 205 PLAY/REC CNTRL Q207 PLAY/REC CNTRL DRVE Q201 PLAY/REC CNTRL L201 BAS SC R CH Q218 BAS SC Q REC/PB EQ AMP C201 A/B REC UT PB UT 5 TAPE A/B Q217 REC SWTCH MUTE CNTRL Q220 Q216 MUTE SWTCH D205 D212 Q209 MUTE Q213 TAPE A/B SWTCH Q214 TAPE A SWTCH D202 D210 D211 D203 SW201 REC/PLAY PLAY D210 Q V D206 D207 SFR201 TAPE SPEED M 11 S201 A DECK S202 B DECK S203 PLAY M901 REC/CAPSTAN MTR SELECTR C CNTRL D CLK CE D CLK CE 1 LNE AMP C Q307 BASS BST SWTCH Q604 MUTE Q603 MUTE SWTCH Q583,584 MUTE DRVE Q303 MUTE PWER AMP C D417 Q409 P MUTE CNT Q410 AC FF DET Q551 Q Q585,586 MUTE D553 C502 SPEAKER RELAY DRVE RL501 R CH JK303 PHNES JK501 SPEAKER D208 D209 REC D416 TU L A TUNER SECTN ST ND TU MUTE D CD L 30V -30V -12V D409 Q408 D401 RECT D414,415 PT001 B CD SECTN SCR SENS SQS XLAT SQCK DATA CUNT FK D CLK CE STB CE CLK D D CLK LED DRVE C Q605,606 LED DRVE Q208 CD SYNC SWTCH LED602 LED601 Q602 RESET SWTCH Q601 PWER DWN DET RM601 3 REMTE CNTRL RECEVER 2 D602-27V 7.9V 11.5V 11.5V (SWTCHED) Q V REG Q V REG Q402 FLTER Q406,407 STCHNG -27V REG Q401 12V REG VLTAGE DUBLER D RECT AC3.4V AC3.4V AC N STB CE CLK D FK CUNT DATA SQCK XLAT SQS SENS SCR D1 TU MUTE FM ST ND ALATCH SYS REC RESET PWER DWN REMTE SYSTEM CNTRLLER/ FLD DRVER C601 DBFB SYSTEM MUTE PWER RCH is omitted 16 X1 12 X2 11 VR UP 44 VR DWN 45 PC UP 55 PC DWN 56 TRAY PEN 59 TRAY CLSE 60 DSC CUNT 57 TURN TABLE 58 K0 K P1 P G1 G Signal Path : PB (DECK A) : PB (DECK B) X MHz A B VR601 ENCDER S01 CD DECK UP/DWN DET S02 TRAY PEN/CLSE DET S03 DSC CUNTER DET S04 TURNTABLE PERATN DET KEY MATRX S FLD601 FLD DSPLAY : REC (DECK A) : FM : CD 15 16

16 HCD-GRX2/RX33 TUNER/CD SECTN FM 75Ω L101 FM ANT FM FRNT END C101 1 RF MX 6 T101 CF MHz Q101 RF F AMP CF MHz 1 FM F FM F FM/AM MPX C102 AM/FM F BUFF MUTE DECDER L 14 R 15 R CH TU L JK101 ANTENNA AM L102 FM RF D101 L104 AM ANT 3 SC 8 D103 L103 TUB Q102 FM SC AMP Q104 AM RF AMP Q105,106 Q103 L.P.F F G VT TP1 AM/FM TUNNG VLTAGE SFR101 FM TUNED LEVEL 19 FM 21 PD1 17 FM B PLL C103 L105 MW SC B AM 18 SD 12 SD 7 ST/MN 14 AM/FM 13 L CTR 15 R CTR 16 MPX 16 FM DET AF DET 18 SC 23 AFC 22 AM RF 21 AM DET AGC SC/FMSD 24 SMET TU LED AM SC PL DET PH DET PH DET AM MX FM DET 8 MPX VC 17 AM F 4 2 ST ND 7 AM/FM 10 CF MHz CF105 19kHz T102 AM FT CF kHz Q109 MUTE ST ND TU MUTE A MAN SECTN RCH is omitted SGNAL PATH :FM :AM :CD B X MHz 24 X 1 X D D CLK CE D D CLK CE D 16 PTCAL PCK-UP BLCK DETECTR LD PD FCUS CL TRACKNG CL VR VC A C B D E F LD GND PD F F T T 5V F/T CL SL/SP MTR T.T/TRAY MTR DRVER C F 2 1 F T T F N 6 T N 5 VCC 8 VCC 7 REG 9 REG B 10 Q01 APC CN2 CN12 Q02 LD N SWTCH Q11 REG 42 TE 1 FE 45 ATSC 48 VC 35 PD1 PD2 36 E 39 F 38 LD 33 PD 34 APC RV01 FCUS TRACKNG 7.5V 5V RF AMP FE AMP FCUS PHASE CMPENSATN CMAND SERAL/ PARALLEL CNVERTER DECDER CD RF/SERV PRSSESR C01 (1/2) FE BAS FE E RV02 FCUS GAN L TTL TTL L TRACKNG PHASE CMPENSATN TA 13 RF FK C UT SENS DATA XLT CLK XRST RF FK 14 CN 13 SE 15 DAT 16 XLT 17 CLK 8 XRST 25 MDP CD DGTAL SGNAL PRCESSR C04 CLV SERV DGTAL CLV EFM DEM. XLN 22 D/A /F DATA CLCK SUB CDE PRSSESR SQCK CPU /F XLAT SQS SENS SCR MUTE SERAL /F S05 LMT SWTCH NL PWM 70 PWM L 69 NR PWM 77 SPA PWM CLCK GEN. 18 R 78 XTA1 73 XTA0 74 MX AMP 2 C05 3 X701 R-CH 1 Q311 MUTE CD L SCR SENS SQS XLAT SQCK DATA CUNT FK B MAN SECTN M102 SLED MTR M101 SPNDL MTR T/T MTR M M M REG UT SL SL N SL 20 SP SP N SP 14 T.T T.T F N T.T T.T R N 12 C01 (2/2) C T.T/TRAY MTR DRVE REG CNTRL C02 6 XRST MUTE 4 11 SPEED 7 T.T DATA 2 CLK 3 14 T.T D CLK D CLK CE TRAY MTR M 30 TR 31 TR TR F N 29 TR T N 28 Q04 13 TR 14 TR STB 1 STB MUTE N 27 SWTCH 5 CNTRL 17 18

17 HCD-GRX2/RX C BLCK DAGRAMS C01 (CD DECRD BARD) CXA1782BQ C102 (MAN BARD) LA1831 C301 (MAN BARD) LC75392 C602 (PANEL BARD) BU2092 C03 (CD DECRD BARD) BA5941FP N4B N4A N3B N3A P UT P N () P N () 22 GND NC NC VCC 19 Vcc UT3A 18 LEVEL SHFT LEVEL SHFT UT3B 17 UT4A 16 LEVEL SHFT LEVEL SHFT UT4B 15 PHD2 PHD1 PHD APC RF V AMP1 LD 33 RF M 32 FK LEVELS RF 31 RF 30 MRR CP 29 CB 28 DFCT CC1 27 CC2 26 L TTL FK SENS 23 C. UT SC/FMSD SC AFC AM RF SMET AM HPF AF DET MPX VC MPX N R UT L UT PL DET LEVEL DET ALC BUFFER AM SC AM MX S-CURVE FM DET AM RF AMP AM/FM F BUFE AM F AGC CMP AM DET TUNNG DRVE FM F REG GND VCC AM FM AM/FM SW MUTE FF VC DECRDER STERE DRVE STERE SW PHASE DET FM F AM MX REG AM F GND TU LED ST ND FM DET VCC AM/FM PH DET PH DET TRG PLT DET LVRUT LVRN LTUT LTCM LT4 LT3 LT2 LT1 L4 L3 L LATCH DECDER SHFT REGSTER RVRUT RVRN RTUT RTCM RT4 RT3 RT2 RT1 R4 R3 R VSS DATA CNTRL CRCUT CLCK LCK VDD E BT SHFT REGSTER 12 BT STRAGE REGSTER 17 Q11 Q10 Q9 Q8 Q7 Q6 Q UTPUT BUFFER (PEN DRAN) Q0 Q1 Q2 Q3 Q4 Vcc MUTE Vcc VCC BAS N N1B N1A N2B N2A GND GND MUTE VCC UT2A UT2B UT1A UT1B FE BAS 37 RF V AMP2 TTL L DATA RESSTR NPUT SHFT RESSTR ADDRESS DECDER TTL L 22 XRST 21 DATA 20 XLT L1 VDD CL D CNTRL R1 VREF VSS CE F 38 FE AMP L UTPUT DECDER 19 CLK E 39 F V AMP FZC CMP TG1-3 FS1-4 TG1-2 TM1-7 PS1-4 BAL VCC C103 (MAN BARD) LC7218-ST GND MUTE CNTRL XRST T.T(M) PS.1 PS C02 (CD DECRD BARD) TC9173P DRVER LATCH LATCH C SERAL / CNTRL T LATCH DRVER VDD STB CLK DATA DATA 0 LADNG M- LADNG M E 40 VEE 41 TE 42 LPF 43 TE 44 ATSC 45 TZC 46 TDFCT 47 VC 48 BAL1 TG1 BAL2 BAL3 TG2 TG3 E V AMP WNDW CMP ATSC TE AMP 1 2 DFCT 3 TZC CMP DFCT TM1 FS4 4 HPF CMP 5 FCS PHASE CMPENSATN LPF CMP 6 FS2 TG1 FS1 7 TRACKNG PHASE CMPENSATN 8 9 TG2 TM5 TM4 TM7 TM6 TM3 10 SET F SET 11 TM SET 16 SL 0 15 SL M 14 SL P 13 TA XN CE D CL D SYC N0 N1 UT0 UT1 UT2 UT REFERENCE DVDER SWALLW CUNTER 1/16. 1/17 BT 12 BT PRGRAMMABLE DVDER SHFT REGSTER LATCH PHASE DETECTR CHARGE PUMP 1 / 2 UNVERSAL CUNTER X UT VSS PD2 PD1 VDD FM N AM N UT 6 HCTR LCTR UT 5 UT 4 C201 (MAN BARD) TA8189N METAL PRE TAPE A REC REC CH2/A CH2/B NF UT UT /TAPE B VCC CG UT NF N ALC CH2 CH2 CH1 GND M/N CH1 CH1/A CH1/B NF METAL PRE MX GND1 M/H REC NF UT UT UT UT A/B VREF1 REF VREF REC N ALC GND GND T.T.SW 8 9 SENSR FE FE FDFCT FGD FLB FE FE M SRCH TGU TG2 FSET TA M

18 SECTN 6 EXPLDED VEWS C PN FUNCTN C601 µpd780205gf (SYSTEM CNTRL) / PANEL BARD Pin No. Pin Name / Description VDD PWER UT S. MUTE UT TU. MUTE UT TUNED UT TAPE REC UT DBFB NRMAL NC NC RESET X2 X1 VSS NC PWER DWN N VDD SCK DATA SS XLAT CE CLK D D VSS CD STB FLAT VSS K4 K3 K2 K1 K0 AVDD AVREF A LATCH B LATCH SCR REMTE N VSS NC VSS DECK STB VR UP VR DWN VDD FM ST N SYNC REC N VSS VSS VDD Power switch output. N: H, FF: L System mute output. N: H, FF: L Tuner mute output. N: H, FF: L Surround output. N: H, FF: L (Not used) Function tape output. Tape: H, thers: L (Not used) DBFB normal (U2: DBFB). N: H, thers: L DBFB high. N: H, thers: L (Not used) Not used Reset input X tal MHz X tal MHz Ground Not used (open) Power down input. AC N: H, AC FF: L VDD CXD2508A SQCK, CLCK output CXD2508A data output CXD2508A SQS input CXD2508A XLAT output. Latch: L, thers: H Chip enable output to LC7218, LC Data: H, Address: L CLK output Data output Data input Ground STB output to SN74HC4094. STB: L, thers: H Flat output. Flat: H, thers: L (Not used) Ground Key input 4 to A/D Key input 3 to A/D Key input 2 to A/D Key input 1 to A/D Key input 0 to A/D VDD of A/D converter Reference voltage of A/D converter Latch output to BU2092. Latch: H, thers: L Not used CXD2508A SCR Remote signal input. N: H, FF: L Ground Shift or load output to SN74HC165. Shift: H, Load: L (Not used) Data input to SN74HC165 (Ground) STB output to BU2114, SN74HC4094. STB:H, thers: L (Not used) VR encoder A input. N:L, FF: H VR encoder B input. N:L, FF: H VDD FM stereo indicator input. Stereo:L, Mono: H Synchro record input. Record:L, ther: H CD encoder A input. N: L, FF: H (Ground) CD encoder B input. N: L, FF: H (Ground) Pin No Pin Name SENS FK CUNT VSS PC UP PC DWN DSC CUNT SW TURN TABLE SW TRAY PEN SW TRAY CLSE SW VSS SER MUTE (TUNER) MDE SW N P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 V LAD P16 P17 P18 P19 P20 P21 G15 G14 G13 G12 G11 G10 G9 G8 G7 G6 G5 G4 G3 G2 G1 / Description nput from CXD2508A SENS nput from CXD2508A FK. K: H, thers: L nput from CXD2508A CUNT Ground nput from CD mechanism pick up switch. Up: L, thers: H nput from CD mechanism pick down switch. Down: L, thers: H nput from CD mechanism disc count switch. Count: L, thers: H nput from CD mechanism turn table switch. N: L, FF: H nput from CD mechanism tray open switch. pen: L, thers: H nput from CD mechanism tray close switch. pen: L, thers: H AMS signal input. During program: H, nterval between programs: L Serial mute (tuner) output (Not used) nput from destination select mode switch. N: H, FF: L FLD segment signal output P1. N: H, FF: L FLD segment signal output P2. N: H, FF: L FLD segment signal output P3. N: H, FF: L FLD segment signal output P4. N: H, FF: L FLD segment signal output P5. N: H, FF: L FLD segment signal output P6. N: H, FF: L FLD segment signal output P7. N: H, FF: L FLD segment signal output P8. N: H, FF: L FLD segment signal output P9. N: H, FF: L FLD segment signal output P10. N: H, FF: L FLD segment signal output P11. N: H, FF: L FLD segment signal output P12. N: H, FF: L FLD segment signal output P13. N: H, FF: L FLD segment signal output P14. N: H, FF: L FLD segment signal output P15. N: H, FF: L () negative power supply FLD segment signal output P16. N: H, FF: L FLD segment signal output P17. N: H, FF: L FLD segment signal output P18. N: H, FF: L FLD segment signal output P19. N: H, FF: L FLD segment signal output P20. N: H, FF: L FLD segment signal output P21. N: H, FF: L FLD grid signal output 15. N: H, FF: L FLD grid signal output 14. N: H, FF: L FLD grid signal output 13. N: H, FF: L FLD grid signal output 12. N: H, FF: L FLD grid signal output 11. N: H, FF: L FLD grid signal output 10. N: H, FF: L FLD grid signal output 9. N: H, FF: L FLD grid signal output 8. N: H, FF: L FLD grid signal output 7. N: H, FF: L FLD grid signal output 6. N: H, FF: L FLD grid signal output 5. N: H, FF: L FLD grid signal output 4. N: H, FF: L FLD grid signal output 3. N: H, FF: L FLD grid signal output 2. N: H, FF: L FLD grid signal output 1. N: H, FF: L NTE: -XX, -X mean standardized parts, so they may have some differences from the original one. tems marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Abbreviation CND : Canadian AUS : Australian MX : Mexican SAF : South African 6-1. CABNET SECTN 1 3 CD mechanism deck not supplied RUBBER, FT DR, CD CABNET * 4 A A MAN BARD, CMPLETE * AC PWER BARD! CRD, PWER (US, CND)! CRD, PWER (MX, SAF) 2 not supplied a #3 #2 1 1 not supplied The mechanical parts with no reference number in the exploded views are not supplied. Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. #2 not supplied a #2 1 0 not supplied When indicating parts by reference number, please include the board name. The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks #2 #2 7 4 PT302 6! CRD, PWER (AUS) WASHER, AC CRD FT (B) * CHASSS! PT TRANSFRMER, PWER (US, CND)! PT TRANSFRMER, PWER (MX, SAF)! PT TRANSFRMER, PWER (AUS) FRNT PANEL SECTN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks WNDW (R), DR LD (R), CASSETTE SPRNG, DR WNDW (L), DR LD (L), CASSETTE KNB, VLUME RNG, VLUME WASHER, VR DAMPER (GRY), GEAR * H.P BARD * DSK BARD * SENSR BARD WRE (FLAT TYPE) (18 CRE) * 64 A A PANEL BARD, CMPLETE * VR BARD * R/P SWTCH BARD PANEL, FRNT EMBLEM (4-A), SNY not supplied Cassette mechanism deck VERAY, DSPLAY WNDW, DSPLAY LENS (A), CD BUTTN LENS (B), CD BUTTN LENS (C), CD BUTTN BUTTN (B), CD BUTTN, PWER BUTTN, CLCK BUTTN, FUNCTN BUTTN, TUNER LENS, PLAY LENS, BUTTN VERAY, BUTTN HLDER (L), DR HLDER (R), DR HLDER, CD BUTTN BRACKET, TP CABNET FLM, BUTTN LENS PLATE, PVC CASSETTE BUTTN SECTN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks BUTTN (L), REC BUTTN (L), PLAY BUTTN (L), REW BUTTN (L), FF BUTTN (L), S/E BUTTN (L), PAUSE BUTTN (R), PLAY BUTTN (R), REW BUTTN (R), FF BUTTN (R), S/E BUTTN (R), PAUSE

19 6-4. CASSETTE MECHANSM DECK SECTN not supplied 161 not supplied M901 SW not supplied HE HRP not supplied SW203 not supplied not supplied 160 SW not supplied HP not supplied not supplied 163 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks CAP SCREW A SCREW 2 7 (AZMUTH) B SCREW PNCH RLLER ARM ASSY SCREW M CLLAR * DECK, MECHANCAL HE E HEAD (ERASE) HP P HEAD (PLAY) HRP RP HEAD (REC/PLAY) M MTR (CAPSTAN/REEL) MTR RUBBER BELT (W) F BELT M SW LEAF SWTCH (A DECK) SW LEAF SWTCH (B DECK) SW LEAF SWTCH (PLAY) 57

20 6-5. CD MECHANSM DECK SECTN M # #7 # #5 #9 215 #5 225 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * MTR BARD PTPWH TRAY, CHANGER BASE PLATE, BLND LEVER, SENSR (SW) SPRNG, SENSR (SW) LEVER BELT, LADNG PULLEY, GEAR GEAR, TR GEAR, TR LCK GEAR (C), RELAY CUSHN CUSHN, SW LEVER GEAR (B), RELAY SCREW, RELAY GEAR (B) GEAR, CHANGE WASHER, CHANGE GEAR SPRNG, CHANGE GEAR WASHER, CHANGE PLATE GEAR (A), RELAY * PLATE, CHANGE WASHER, PLY ETHYLENE * SW (B) BARD * SW (A) BARD * GUDE, RAL TURN TABLE M103 X MTR ASSY (TURN TABLE) 58

21 6-6. CD MECHANSM DECK SECTN 2 not supplied # #7 252 # M Base unit block 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks WRE (FLAT TYPE) (5 CRE) UD-CAM UD-GEAR MAGNET * CHASSS, MAN SPRNG, BRAKE CAM LEVER, SW * SW (D) BARD * SW (C) BARD CLAMP BELT, LADNG GEAR PULLEY (B), GEAR GEAR, SLDE RLLER WASHER, PLYETHYLENE * 268 A A CD DECDER BARD, CMPLETE M104 X MTR ASSY (A) (TRAY) 59

22 6-7. BASE UNT SECTN (KSM-213BCM) not supplied 302 #6 #6 302 # #6 M102 M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks BASE, KSM MECHANCAL DAMPER (GREEN) DAMPER (RED) SPRNG, MECHANCAL BASE GEAR (A) (S) GEAR (B)! PTCAL PCK-UP KSS-213B/S-N * MTR (6P)(S) BARD WRE (FLAT TYPE) (16 CRE) M101 X MTR ASSY (SPNDLE) SHAFT, SLED M102 X MTR ASSY (SLED) 60 The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

23 NTE: When indicating parts by reference number, please include the board name. The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Abbreviation CND : Canadian AUS : Australian MX : Mexican SAF : South African SECTN 7 ELECTRCAL PARTS LST Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. tems marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. CAPACTRS: uf: µf AC PWER CD DECDER RESSTRS All resistors are in ohms. METAL: metal-film resistor METAL XDE: Metal xide-film resistor F: nonflammable CLS uh: µh SEMCNDUCTRS n each case, u: µ, for example: ua...: µa..., upa..., µpa..., upb..., µpb..., upc..., µpc..., upd..., µpd... Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * AC PWER BARD *************** * HLDER, FUSE < FUSE >! F FUSE 250V/3A < RESSTR >! R CARBN 4.7M 5% 1/3W ************************************************************ * A A CD DECDER BARD, CMPLETE *************************** < CAPACTR > C ELECT 4.7uF 20% 50V C ELECT 100uF 20% 10V C CERAMC 0.01uF 20% 16V C04A CERAMC 0.1uF 50V C FLM 0.033uF 5% 50V C CERAMC 0.01uF 20% 16V C FLM 0.033uF 5% 50V C07A CERAMC 10PF 5% 50V C CERAMC 0.022uF 25V C ELECT 0.47uF 20% 50V C CERAMC 0.01uF 20% 16V C ELECT 100uF 20% 10V C11A CERAMC 0.1uF 50V C CERAMC 0.01uF 20% 16V C CERAMC 0.1uF 50V C CERAMC uF 30% 16V C CERAMC 0.1uF 50V C FLM 0.033uF 5% 50V C FLM 0.1uF 5% 50V C CERAMC 0.1uF 50V C ELECT 4.7uF 20% 50V C CERAMC 0.01uF 20% 16V C FLM 0.022uF 5% 50V C ELECT 100uF 20% 10V C CERAMC 0.1uF 50V C ELECT 100uF 20% 10V C30A CERAMC 0.1uF 50V C CERAMC uF 30% 16V C CERAMC uF 30% 16V C CERAMC 0.01uF 20% 16V C CERAMC 220PF 10% 50V C CERAMC 0.01uF 20% 16V C ELECT 4.7uF 20% 50V C CERAMC 0.1uF 50V C37A ELECT 470uF 20% 10V C CERAMC 20PF 5% 50V C CERAMC 20PF 5% 50V C41A CERAMC 0.001uF 10% 50V C42A CERAMC 0.001uF 10% 50V C44A CERAMC 0.001uF 10% 50V C ELECT 220uF 20% 10V C ELECT 100uF 20% 10V C CERAMC 330PF 10% 50V C51A ELECT 0.47uF 20% 50V C CERAMC 330PF 10% 50V C CERAMC 150PF 10% 50V C CERAMC 150PF 10% 50V C CERAMC 150PF 10% 50V C CERAMC 150PF 10% 50V C ELECT 2.2uF 20% 50V C ELECT 2.2uF 20% 50V C CERAMC 0.001uF 10% 50V C CERAMC 0.001uF 10% 50V C CERAMC 0.1uF 50V C CERAMC 0.1uF 50V C CERAMC 100PF 10% 50V C CERAMC 680PF 10% 50V C CERAMC 100PF 10% 50V C86A CERAMC 0.022uF 25V C CERAMC 100PF 10% 50V C CERAMC 100PF 10% 50V C CERAMC 0.022uF 25V C90A CERAMC 0.1uF 50V C CERAMC 0.022uF 25V < CNNECTR > C ELECT 22uF 20% 50V C ELECT 1uF 20% 50V C CERAMC 0.022uF 25V C CERAMC 0.01uF 20% 16V C CERAMC 0.1uF 50V CN SCKET, CNNECTR 16P CN PN, CNNECTR (SMALL TYPE) 5P CN PN, CNNECTR (PC BARD) 5P CN PN, CNNECTR (PC BARD) 21P 61

24 CD DECDER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < DDE > D DDE 1SS D DDE 1SS133T D04A DDE 1SS176 R CARBN 1M 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 4.7K 5% 1/4W < C > C C CXA1782BQ C C TC9173P C C BA5941FP C C CXD2508AQ C C NJM4558L C C NJM4558L < CL > L NDUCTR 10uH < TRANSSTR > Q TRANSSTR 2SA952 Q TRANSSTR 2SA952 Q TRANSSTR 2SC945-P Q TRANSSTR 2SA952 < RESSTR > R CARBN 12K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 22 5% 1/4W F R04A CARBN 220 5% 1/4W R CARBN 22K 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 12K 5% 1/4W R07A CARBN 12K 5% 1/4W R07B CARBN 12K 5% 1/4W R CARBN 15K 5% 1/4W R CARBN 15K 5% 1/4W R09A CARBN 4.7K 5% 1/4W R CARBN 2.7K 5% 1/4W F R CARBN 56K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 510K 5% 1/4W R13A CARBN 18K 5% 1/4W R CARBN 100K 5% 1/4W R14A CARBN 18K 5% 1/4W R CARBN 120K 5% 1/4W R CARBN 220K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 8.2K 5% 1/4W F R CARBN 15K 5% 1/4W R CARBN 22K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 150K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 3.3K 5% 1/4W R CARBN 3.3K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 100 5% 1/4W R CARBN 100 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 100 5% 1/4W R CARBN 100 5% 1/4W R CARBN 100 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 4.7K 5% 1/4W F R CARBN 330 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 6.8K 5% 1/4W F R CARBN 510 5% 1/4W R CARBN 1M 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 10K 5% 1/4W R CARBN 24K 5% 1/4W R CARBN 24K 5% 1/4W R CARBN 24K 5% 1/4W R CARBN 24K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 12K 5% 1/4W R CARBN 2.2K 5% 1/4W R CARBN 2.2K 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 4.7K 5% 1/4W R CARBN 100 5% 1/4W F R CARBN 150K 5% 1/4W R CARBN 100 5% 1/4W R CARBN 100 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 47K 5% 1/4W R CARBN 47K 5% 1/4W R CARBN 47K 5% 1/4W R CARBN 47K 5% 1/4W R CARBN 100K 5% 1/4W R CARBN 2.2K 5% 1/4W R CARBN 2.2K 5% 1/4W R90B CARBN 1K 5% 1/4W R CARBN 2.2K 5% 1/4W R CARBN 2.2K 5% 1/4W R CARBN 1.8K 5% 1/4W F R CARBN 1.8K 5% 1/4W F < VARABLE RESSTR > VR RES, ADJ, METAL 47K VR RES, ADJ, METAL 220K < CRYSTAL > XTL VBRATR, CRYSTAL MHz ************************************************************ 62

25 DSK H.P MAN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * DSK BARD ********** < RESSTR > R CARBN 2.7K 5% 1/4W R CARBN 3.9K 5% 1/4W F R CARBN 6.8K 5% 1/4W F R CARBN 15K 5% 1/4W R CARBN 39K 5% 1/4W < SWTCH > S SWTCH, PUSH (DSC 1) S SWTCH, PUSH (DSC 2) S SWTCH, PUSH (DSC 3) S SWTCH, PUSH (DSC SKP) S SWTCH, PUSH (PEN/CLSE) ************************************************************ * H.P BARD ********* < JACK > JK JACK (LARGE TYPE)(PHNE) ************************************************************ * A A MAN BARD, CMPLETE ********************* * HLDER, FUSE < CAPACTR > C CERAMC 0.001uF 10% 50V C CERAMC 0.001uF 10% 50V C CERAMC 3.3PF 10% 50V C CERAMC 0.022uF 25V C CERAMC 20PF 5% 50V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C CERAMC 2.2PF 10% 50V C CERAMC 2.2PF 10% 50V C CERAMC 56PF 5% 50V C CERAMC 100PF 10% 50V C CERAMC 0.1uF 50V C CERAMC 0.001uF 10% 50V C FLM 470PF 5% 50V C CERAMC 15PF 5% 50V C ELECT 100uF 20% 16V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C CERAMC 15PF 5% 50V C ELECT 2.2uF 20% 50V C ELECT 1uF 20% 50V C CERAMC 20PF 5% 50V C ELECT 1uF 20% 50V C CERAMC 47000PF 50V C ELECT 10uF 20% 50V C CERAMC 0.022uF 25V C ELECT 1uF 20% 50V C CERAMC 0.018uF 10% 25V C CERAMC 0.018uF 10% 25V C CERAMC uF 10% 50V C CERAMC uF 10% 50V C CERAMC 0.001uF 10% 50V C ELECT 3.3uF 20% 50V C ELECT 0.47uF 20% 50V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C ELECT 0.47uF 20% 50V C CERAMC 0.022uF 25V C CERAMC 56PF 5% 50V C CERAMC 0.001uF 10% 50V C CERAMC 0.022uF 25V C CERAMC 100PF 10% 50V C CERAMC 0.1uF 50V C ELECT 22uF 20% 25V C CERAMC 100PF 10% 50V C CERAMC 100PF 10% 50V C CERAMC 100PF 10% 50V C CERAMC 27PF 5% 50V C CERAMC 27PF 5% 50V C ELECT 47uF 20% 16V C CERAMC 100PF 10% 50V C ELECT 4.7uF 20% 50V C ELECT 4.7uF 20% 50V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C CERAMC 100PF 10% 50V C CERAMC 0.022uF 25V C CERAMC 10PF 5% 50V C CERAMC 220PF 10% 50V C CERAMC 220PF 10% 50V C CERAMC 680PF 10% 50V C CERAMC 680PF 10% 50V C CERAMC 220PF 10% 50V C CERAMC 220PF 10% 50V C ELECT 47uF 20% 16V C ELECT 47uF 20% 16V C CERAMC 0.012uF 10% 25V C CERAMC 0.012uF 10% 25V C ELECT 1uF 20% 50V C ELECT 1uF 20% 50V C CERAMC 0.001uF 10% 50V C CERAMC 0.001uF 10% 50V C MYLAR uF 5% 50V C MYLAR uF 5% 50V C CERAMC 220PF 10% 50V C CERAMC 220PF 10% 50V C ELECT 3.3uF 20% 50V C ELECT 3.3uF 20% 50V C ELECT 47uF 20% 16V C ELECT 47uF 20% 16V C CERAMC 0.001uF 10% 50V 63

26 MAN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C CERAMC 0.001uF 10% 50V C ELECT 3.3uF 20% 50V C ELECT 3.3uF 20% 50V C ELECT 10uF 20% 50V C MYLAR 0.015uF 5% 50V C CERAMC 100PF 10% 50V C CERAMC 100PF 10% 50V C CERAMC 0.1uF 50V C CERAMC 0.1uF 50V C MYLAR 0.015uF 5% 50V C MYLAR 0.01uF 5% 50V C CERAMC uF 30% 16V C FLM 0.022uF 5% 50V C ELECT 47uF 20% 16V C CERAMC 0.022uF 25V C ELECT 330uF 20% 10V C ELECT 3.3uF 20% 50V C CERAMC 680PF 10% 50V C CERAMC 680PF 10% 50V C ELECT 47uF 20% 16V C ELECT 2.2uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C CERAMC 10PF 5% 50V C CERAMC 10PF 5% 50V C MYLAR 0.001uF 5% 50V C MYLAR 0.001uF 5% 50V C MYLAR 0.015uF 5% 50V C MYLAR 0.015uF 5% 50V C CERAMC 470PF 10% 50V C CERAMC 470PF 10% 50V C CERAMC 15PF 5% 50V C CERAMC 15PF 5% 50V C MYLAR 0.015uF 5% 50V C MYLAR 0.015uF 5% 50V C ELECT 220uF 20% 16V C ELECT 220uF 20% 16V C CERAMC 10PF 5% 50V C CERAMC 10PF 5% 50V C ELECT 100uF 20% 16V C ELECT 1uF 20% 50V C ELECT 1uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 0.47uF 20% 50V C CERAMC 47PF 5% 50V C CERAMC 47PF 5% 50V C CERAMC 100PF 10% 50V C CERAMC 100PF 10% 50V C ELECT 100uF 20% 16V C ELECT 2.2uF 20% 50V C ELECT 2.2uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 10uF 20% 50V C ELECT 100uF 20% 16V C MYLAR 0.015uF 5% 50V C CERAMC 150PF 10% 50V C CERAMC 150PF 10% 50V C MYLAR uF 5% 50V C MYLAR uF 5% 50V C ELECT 2.2uF 20% 50V C CERAMC 220PF 10% 50V C CERAMC 220PF 10% 50V C CERAMC 220PF 10% 50V C ELECT 10uF 20% 50V C ELECT 3300uF 20% 50V C ELECT 3300uF 20% 50V C ELECT 220uF 20% 50V C ELECT 47uF 20% 16V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C ELECT 2200uF 20% 25V C MYLAR 0.01uF 5% 50V C ELECT 100uF 20% 16V C MYLAR 0.01uF 5% 50V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C ELECT 100uF 20% 16V C ELECT 470uF 20% 16V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C CERAMC 0.022uF 25V C ELECT 470uF 20% 16V C CERAMC 0.022uF 25V C MYLAR 0.01uF 5% 50V C MYLAR 0.01uF 5% 50V C ELECT 100uF 20% 16V C CERAMC 0.022uF 25V C ELECT 100uF 20% 16V C ELECT 220uF 20% 50V C ELECT 220uF 20% 63V C ELECT 100uF 20% 16V C CERAMC 0.022uF 25V C CERAMC 0.022uF 25V C ELECT 220uF 20% 16V C ELECT 100uF 20% 50V C ELECT 1uF 20% 50V C CERAMC 0.001uF 10% 50V C CERAMC 0.001uF 10% 50V C CERAMC uF 30% 16V C CERAMC uF 30% 16V 64