ICF-SC1/SC1PC SERVICE MANUAL PLL SYNTHESIZED SCANNING RECEIVER. US Model. Ver SPECIFICATIONS

Transcription

1 ICF-SC1/SC1PC SERVICE MANUAL Ver US Model SPECIFICATIONS Circuit system : Triple conversion superheterodyne Frequency range : MHz (excluding cellular phone band : MHz and MHz) Detection mode : AM, NFM, WFM Speaker : Approx. 36 mm (1 7 /16 inches) dia., 8 ohms Power output : 150mW(at 10% harmonic distortion Output jack (monaural minijack) Power requirements : DC 6V, four size AA (R6) batteries External power source : DC 6V Dimensions : Approx. 64 x 177 x 44.3 mm (w/h/d) (2 5 /8 x 7 x 1 3 /4 inches) incl. projecting parts and controls, not including the helical antenna and the belt holder Mass : Approx. 252g (8.9 oz) Approx. 382g (13.5 oz) incl. alkaline batteries, helical antenna, and the belt holder Supplied Accessories AC power adaptor (1) Earphone (1) Belt holder (1) Helical antenna (1) Frequency guidebook (1) CD-ROM (1) (ICF-SC1PC only) Serial port connecting cable (1) (ICF-SC1PC only) Clamp filter (1) (ICF-SC1PC only) Design and specifications are subject to change without notice. PLL SYNTHESIZED SCANNING RECEIVER MICROFILM

2 TABLE OF CONTENTS Specifications GENERAL Location and Function of Controls DISASSEMBLY 2-1. Helical Antenna Removal Cabinet (Rear) Assy Removal Microcomputer Board, IF Board, RF Board Removal TEST MODE ELECTRICAL ADJUSTMENS DIAGRAMS 5-1. Explanation of IC Terminals Block Diagram Printed Wiring Boards IF Section Schematic Diagram IF Section Printed Wiring Boards Microcomputer Section Schematic Diagram Microcomputer Section Printed Wiring Boards RF Section Schematic Diagram RF Section (1/2) Schematic Diagram RF Section (2/2) EXPLODED VIEW ELECTRICAL PARTS LIST SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK! OR DOTTED LINE WITH MARK! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 2

3 SECTION 1 GENERAL This section is extracted from instruction manual. LOCATION AND FUNCTION OF CONTROLS FRONT 3

4 SIDE/REAR DISPLAY 4

5 5

6 6

7 7

8 8

9 9

10 SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given HELICAL ANTENNA REMOVAL Helical antenna CABINET (REAR) ASSY REMOVAL 2 Screws 2 Screws Claw Cabinet (Rear) assy Battery case lid Claws 4 Claws 10

11 2-3. MICROCOMPUTER BOARD, IF BOARD, RF BOARD REMOVAL 2 Remove solder IF board RF board 5 Screws 5 Screws 4 3 CN402 (22pin) Microcomputer board 6 1 Knob (VOL) Cabinet (Front) assy Coaxial connector 7 Remove solder! 8! IF board!º!!º! RF board!!º 9 CN401 (16pin) Chassis! 11

12 SECTION 3 TEST MODE Reading the S-Curve voltage for scan-stop The ICF-SC1 and SC1PC have a scan-stop function used to scan for the correct frequency. Scanning continues until the squelch turns off (when a signal is received). However, just setting the squelch off as condition does not guarantee that the scan-stop function will always stop at the correct frequency. (It might for instance deviate 1 step to an adjacent frequency.) So scan-stop is set to trigger only at the correct frequency, by checking the DC voltage component (S-curve voltage) of the FM detector output. The DC voltage component of the FM detector output may vary however, due to variations in the parts components of the FM detector circuit or deviations in the local oscillator frequency. Therefore, once repair or alignment is complete, read the DC voltage component of the RF detector output while it is input with an IF signal from a signal generator, and use that value as a reference to write data on the EEPROM. Two types of writing are performed on the EEPROM since there are two types of FM detectors. S-Curve voltage write method Signal input method using signal generator. 1. In NFM IC401 TA31136FN MIX IN 16 C P (1) Connect a signal generator to TP1 by way of a 0.01µF capacitor. (2) Receive NFM (Receive frequency does no matter) (3) Input 455kHz from the signal generator, 90 to 100dBµ, modulation 30%, mod frequency of 1kHz. (4) Write the COMPN terminal voltage onto the ROM. (5) Press the [SVC] button. When data is written, a display as shown below appears. TP1 0.01µ S.G. 45M X'tal filter WFM n for WFM NFM n for NFM, AM Refer to the following for information on the write method and on the signal input method using a signal generator. LCD (all lamps on) All LCD lamps up when the three [EXE], [ ] and [SCAN] keys are simultaneously held down while the power is off. 2. In WFM NFM 0.94 Voltage (V) Reading the S-Curve voltage component 1. Input method for S-Curve voltage component read mode Simultaneously hold down the [MODE], [STEP] and [BAND] keys for at least 1second while power is off. The set (ICF-SC1/SC1PC) power turns on and a display as shown below appears. IC402 CXA1111N FM RF IN 10 C µ TP4 0.01µ S.G. RF BOARD 2. Quitting S-Curve voltage read mode Press the [POWER] button. (1) Connect a signal generator to TP4 by way of a 0.01µF capacitor. (2) Receive WFM (Receive frequency does no matter) (3) Input 10.7MHz from the signal generator, 90 to 100dBµ, frequency deviation 22.5kHz, mod frequency of 1kHz. (4) Write the COMPW terminal voltage onto the ROM. (5) Press the [SCAN] button. When data is written, a display as shown below appears. Note : When set in S-Curve voltage read mode, do not connect anything to the antenna terminal while the power to the RF section is on. (An unwanted signal might otherwise be received through the antenna.) However when set, a check can be made that a broadcast RF carrier wave was received. (1) Turn the power on as usual and receive a broadcast signal. (2) Turn off the power and set in read mode with [MODE] + [STEP] + [BAND]. (3) Write can be checked with [SVC] or [SCAN] since the broad cast signal received in (1) can be heard. WFM Adjustment Location : [ IF BOARD] (Rear side) 0.87 Voltage (V) In the following cases the message TRY AGAIN appears and writing is disabled. (1) When the Squelch is closed. (2) When the S-curve voltage that was read, is not within 0.5V to 1.3V. CN402 COMPN COMPW 12

13 SECTION 4 ELECTRICAL ADJUSTMENTS Setting : trackig generator spectrum analyzer (GND) IF BOARD (SINGLE) ADJUSTMENT 1. 3rd local oscillator Adjustment Procedure : (1) Connect a spectrum analyzer to TP2. (2) Receive a MHz signal. (3) Adjust the CT401 so that the 3rd local oscillator = MHz. (spectrum analyzer span = 10kHz) (4) Recive a MHz signal. (5) Adjust the 3rd local oscillator to MHz with RV401. (spectrum analyzer span = 10kHz) Adjustment Location IF : board (see page 14) (GND) RF & IF BOARD (COMBINATION) ADJUSTMENT FM RF signal generator digital voltmeter (GND) (GND) RF BOARD (SINGLE) ADJUSTMENT 1. 2nd local oscillator Adjustment Procedure : (1) Connect a tracking generator to TP10 and a spectrum analyzer to TP6. (TG level = 40 to 50dBm, spectrum analyzer span = 200MHz) (2) Receive a 600MHz signal. (3) Repeatedly adjust CT303, 304 and 305 for an optimal waveform at center frequency of 277.5MHz. (4) Receive the 25MHz signal. (5) Adjust the 2nd local oscillator to 555MHz with CT302. (spectrum analyzer span = 10kHz) 2. 1st local oscillator Adjustment Procedure : (1) Connect a spectrum analyzer to TP5. (2) Receive a 767.5MHz signal. (3) Adjust the CT301 so that 1st local oscillator = 1000MHz (spectrum analyzer span = 10kHz) 3. 1st IF (low) Adjustment Procedure : (1) Connect a tracking generator to TP5 and a spectrum analyzer to TP7. (2) Recive a 500MHz signal. (3) Repeatedly adjust CT201, 202 and 203 for an optimal waveform (ladder shape) at center frequency of 232.5MHz. (TG level = 30 to 40dBm, spectrum analyzer span = 200MHz) 1. 2nd IF (narrow) Adjustment Procedure : (1) Connect a tracking generator to RF (RF board) TP6 and connect a spectrum analyzer to IF (IF board) TP1 by way of a 0.5pF capacitor. (2) Receive a 29MHz signal. (3) Align for an optimal waveform with T206. (ladder waveform with minimum ripple) (TG level = 50dBm, spectrum analyzer Center freq. = 45MHz, span = 100kHz) 2. 2nd IF (wide) Adjustment Procedure : (1) Connect a tracking generator to RF (RF board) TP6 and connect a spectrum analyzer to IF (IF board) TP3. (2) Receive a 70MHz signal. (3) Adjust so the 45MHz is at maximum by using CT402 and T205. (TG level = 50dBm, spectrum analyzer Center freq. = 45MHz, span = 50MHz) 3. AGC Adjustment Procedure : (1) Connect a FM RF signal generator to the BNC (ANT IN) connector. (2) Connect a digital voltmeter to RV403 center tap (COMMON). (IF board) (3) Receive a 122MHz signal (input level 80d µemf, AM, modulation 30%). (4) Adjust RV403 so that digital voltmeter reading is at 1.68 ± 0.02V. Adjustment Location RF, : IF board (see page 14) * Use semirigid cable when connecting the tracking generator and spectrum analyzer to the circuit board. * Spectrum analyzer settings shown in the ( ) are reference values. Adjustment Location RF : board (see page 14) 13

14 Adjustmen Location : [RF BOARD] (Front side) TP2 TP3 TP5 TP6 TP7 TP1 TP10 [RF BOARD] (Rear side) ANT IN (BNC connector) CT301 CT305 CT304 CT303 CT302 T206 CT201 CT202 CT203 T205 [ IF BOARD] (Rear side) GND TP1 TP2 GND RV401 CT401 RV403 center tap (COMMON) RV403 TP4 CT402 TP3 14

15 SECTION 5 DIAGRAMS 5-1. EXPLANATION OF IC TERMINALS IC604 µ PD78064BGC (SYSTEM CONTROL) Pin No. Pin name I/O Description 1 COMP-W I WFM S-curve voltage input (A/D input). 2 BATT I Low battery voltage detection input (A/D input). 3 7 KS0 4 O Key matrix output. 8 AVDD Power supply for A/D converter. 9 AVREF Power supply for A/D reference. 10 AC-DET I External power supply detect terminal. 11 LED O LED drive. H : Lighting 12 VSS Ground. 13 TEST I Test mode terminal. H : Test mode 14 LCD I H : Normal. (LCD display ON = H during PC operaion) 15 BEEP O Beep signal output. 16 SCAN O Scan signal output. H : Scan run 17 DUB Not used (Open). 18 WFM O WFM mode select. H : WFM mode 19 D/A 0 O D/A output bit 0 for minute step. 20 D/A 1 O D/A output bit 1 for minute step. 21 STANDBY O Standby signal output. H : RS232C interface OFF 22 MUTE O Mute signal output. H : Mute ON COM0 2 O LCD common output. 26 COM3 Not used (Open). 27 BIAS LCD bias terminal VLC0 2 LCD bias terminal. 31 VSS Ground S0 30 O LCD segment output. 63 Not used (Open). 64 AM O AM mode output. H : AM mode 65 NFM O NFM mode output. H : NFM mode 66 IF 1 O IF selection output. 67 RF O RF selection output. 68 MAIN O Main power supply ON/OFF control. 69 FILTER O Serial latch output for filter selection. 70 PLL O Serial latch output for PLL selection. 71 ROM O Clock output for EEPROM. 72 DO I Serial data input from EEPROM. 73 DI O Serial data output to EEPROM. 74 CLK O Serial clock output. 75 RXD I RXD input from RS232C interface. 76 TXD O TXD output to RS232C interface. 77 CTS O CTS output to RS232C interface. 78 IC (GND) Ground. 79 XM2 Main clock oscillator ( MHz). 80 XM1 Main clock oscillator ( MHz). 81 VDD Power supply (+4.0V). 82 XS2 Sub clock oscillator (32.768kHz). 83 XS1 Sub clock oscillator (32.768kHz). 84 RESET I System reset terminal. 85 OFF-DET I Low power detection OFF input. L : OFF 15

16 Pin No. Pin name I/O Description 86 L-DET I PLL lock detect. L : Lock 87 N-DET I Squelch detection input. L : 88 RTS I RTS input from RS232C interface. 89 CONNECT I PC connect check signal input. 90 REMOTE I PC connect check signal input. 91 Not used (Open). 92 Not used (Open) KR5 0 I Key matrix input. 99 VSS Ground. 100 COMP-N I NFM (AM) S-curve voltage input (A/D input). 16

17 ICF-SC1/SC1PC 5-2. BLOCK DIAGRAM Signal path. F 17 18

18 5-4. SCHEMATIC DIAGRAM IF SECTION r Refer to page 33 for IC Block Diagrams. ICF-SC1/SC1PC Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. U : B+ Line. Power voltage is dc 6 V and fed with regulated dc power supply from external power voltage jack (J402). Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : WFM/AM/NFM ( ) : AM/NFM < > : NFM Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Signal path. F 21 22

19 5-6. SCHEMATIC DIAGRAM MICROCOMPUTER SECTION r Refer to page 33 for IC Block Diagrams. ICF-SC1/SC1PC Note: X : parts extracted from the component side. D : Chip components extracted from the rear side. r : Through hole. b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. U : B+ Line. Power voltage is dc 6 V and fed with regulated dc power supply from external power voltage jack (J402). Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : WFM/AM/NFM ( ) : AM/NFM < > : NFM Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. r WAVEFORMS 1 0.5Vp-p 32.7 µsec IC604 * VOLT/DIV : 0.2 V AC TIME/DIV : 20 msec 2 2Vp-p 0.24 µsec IC604 &ª VOLT/DIV : 1 V AC TIME/DIV : 0.2 msec 25 26

20 ICF-SC1/SC1PC 5-8. SCHEMATIC DIAGRAM RF SECTION (1/2) r Refer to page 33 for IC Block Diagrams. Note: X : parts extracted from the component side. D : Chip components extracted from the rear side. r : Through hole. b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. U : B+ Line. Power voltage is dc 6 V and fed with regulated dc power supply from external power voltage jack (J402). Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : WFM/AM/NFM ( ) : AM/NFM < > : NFM Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Signal path. F 29 30

21 ICF-SC1/SC1PC 5-9. SCHEMATIC DIAGRAM RF SECTION (2/2) r Refer to page 33 for IC Block Diagrams. Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. U : B+ Line. Power voltage is dc 6 V and fed with regulated dc power supply from external power voltage jack (J402). Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : WFM/AM/NFM ( ) : AM/NFM < > : NFM Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Signal path. F 31 32

22 r IC BLOCK DIAGRAMS IC301 MB1511-PFV-EF R NC P F OSC SW FC LE DATA NC CLK PHASE COMPARATPR MONITOR FREQUENCY SELECT CIRCUIT ANALOG SWITCH CONTROL 1BIT LATCH SWITCH BINARY 14BIT REFERENCE COUNTER 15BIT LATCH 16BIT SIFT RESISTER 19BIT SIFT RESISTER 18BIT LATCH BINARY 11BIT PROGRAMABLE COUNTER BINARY 7BIT SWALLOW COUNTER CONTROL CIRCUIT OSCILLATOR CHAGE PUMP PRESCALER CIRCUIT OSC I NC OSC O VP IC401 TA31136FN IC402 CXA1111N MIX IN GND MIXER BUFFER LOCAL OSCILLATION N-REC N-DET RSSI NOISE COMPARATOR DETECTOR RSSI IF OUT IF AMP QUAD QUADRATURE DETECTION OSC IN OSC OUT MIX OUT VCC IF IN DEC FIL OUT 10 NOISE AMP FIL IN L.P.F AF OUT 9 FILTER AMP MUTE VCC FILTER BAND SIGNAL OUTPUT CIRCUIT AM. FE DET AFCJ FM. IF DISCRI FM. FE AFCW IF RIPPLE FILTER EARTH TUNE TUNING METER FM IF AM IF AM. IF DET. AGC BAND REGULATOR EARTH DISCRI AM OSC AFC FM OSC REG FM RF AM RF VCC DO LD GND NC F IN NC FM IN EARTH MIX OUT IC407 CXA1522N IN1 REG VOL NF1 GND1 P-GND1 OUT1 VCC PRE+POWER1 REG VOL PRE+POWER IN2 NC NC NF2 GND2 P-GND2 OUT2 RIPPLE 33

23 IC605 AT25160N-10SC2.7T IC607 µ PD4721GS-GJG-E2 (ICF-SC1PC) CS VCC SO WP HOLD GND SCK CLOCK GENERATOR SI C4+ GND C4 VSS STBY VCHA DOUT1 DOUT2 RIN1 RIN STATUS REGISTER MEMORY ARRAY 1024/2048/ 4096/8192X8 ADDRESS DECODER OUTPUT BUFFER DATA REGISTER MODE DECODE LOGIC VDD C1+ VCC C1 C5+ C5 DIN1 DIN2 ROUT1 ROUT2 34

24 SECTION 6 EXPLODED VIEW NOTE : -XX, -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. ANT101 The mechanical parts with no reference number in the exploded views are not supplied. Hardware (# mark) list and accessories and packing materials are given in the last of this parts list ra (including ra) # LCD # # SP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X CABINET (FRONT) ASSY (SC1) 1 X CABINET (FRONT) ASSY SHEET (SPEAKER) GRILLE (SPEAKER) (SC1) GRILLE (SPEAKER) EMBLEM (NO.3.5), SONY SPRING, RING KNOB (VOL) BUTTON (POWER) BUTTON (LIGHT) SWITCH, RUBBER KEY * 10 A A MICROCOMPUTER BOARD, COMPLETE * 10 A A MICROCOMPUTER BOARD, COMPLETE (SC1) CASE (LCD) * SPACER (B) CONDUCTIVE BOARD, CONNECTION PLATE, LIGHT GUIDE PLATE, CONTACT CORD SCREW (M2X6), TAPPING, P3 * CUSHION (D) * 19 A A RF BOARD, COMPLETE * CHASSIS CABLE, FLEXIBLE FLAT (22 CORE) CUSHION (A) LUG (BNC) FRAME RING (BNC) (SC1) RING (BNC) CONNECTOR, COAXIAL (BNC TYPE) SPACER (C) LED, BATTERY CASE (SC1) LED, BATTERY CASE * 29 A A IF BOARD, COMPLETE * CUSHION (B) CUSHION CABLE, FLEXIBLE FLAT (16 CORE) CABINET (REAR) (SC1) CABINET (REAR) SPRING (+/-.B), BATTERY TERMINAL (+), BATTERY SPRING (+/-.A), BATTERY TERMINAL (-), BATTERY ANT ANTENNA, HELICAL LCD DISPLAY PANEL, LIQUID CRYSTAL SP SPEAKER (3.6cm)

25 IF NOTE : Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms METAL : Metal-film resistor METAL OXIDE :Metal oxide-film resistor F : nonflammable Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SECTION 7 ELECTRICAL PARTS LIST SEMICONDUCTORS In each case, u : µ, for example : ua... : µ A..., upa... : µ PA... upb... : µ PB..., upc... : µ PC... upd... : µ PD... CAPACITORS uf : µ F COILS uh : µ H The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * A A IF BOARD, COMPLETE ****************** C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 330PF 5% 50V < CAPACITOR > C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 0.01uF 10% 25V C ELECT CHIP 10uF 20% 16V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 7PF 0.5PF 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 91PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 27PF 5% 50V C CERAMIC CHIP 7PF 0.5PF 50V C CERAMIC CHIP 0.001uF 10% 50V C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 27PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.001uF 10% 50V C TANTAL. CHIP 4.7uF 20% 6.3V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP uF 10% 50V C CERAMIC CHIP 0.1uF 25V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 1uF 10V C ELECT CHIP 10uF 20% 16V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 0.1uF 10% 16V C ELECT CHIP 220uF 20% 10V C CERAMIC CHIP 0.1uF 25V C CERAMIC CHIP 0.015uF 10% 25V C CERAMIC CHIP 1uF 16V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 0.1uF 10% 16V C ELECT CHIP 22uF 20% 6.3V C ELECT CHIP 220uF 20% 10V C CERAMIC CHIP 0.01uF 10% 25V C ELECT CHIP 220uF 20% 10V C CERAMIC CHIP 0.1uF 10% 16V C ELECT CHIP 220uF 20% 10V C CERAMIC CHIP 0.1uF 10% 16V C ELECT CHIP 220uF 20% 10V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 220PF 5% 50V C CERAMIC CHIP 1uF 25V C ELECT CHIP 4.7uF 20% 35V C ELECT CHIP 4.7uF 20% 35V C CERAMIC CHIP 0.1uF 10% 16V C ELECT 22uF 20% 16V C ELECT 22uF 20% 16V C CERAMIC CHIP 0.01uF 10% 25V 36

26 IF Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V < FILTER > CF FILTER, CERAMIC(DISCRIMINATOR) CF FILTER, CERAMIC CF FILTER, CERAMIC CF FILTER, CERAMIC CF FILTER, CERAMIC < CONNECTOR > CN HOUSING, FPC CONNECTOR(ZIF)16P CN HOUSING, FPC CONNECTOR(ZIF)22P < TRANSISTOR > Q TRANSISTOR 2SC4178-F13 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SA1745 Q TRANSISTOR 2SC4178-F13 Q TRANSISTOR 2SC4178-F13 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SB815B7-TB Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SB1115A Q TRANSISTOR 2SA1745 Q TRANSISTOR 2SC4177 Q TRANSISTOR 2SB815B7-TB < TRIMMER > CT CAP, CHIP TYPE TRIMMER 20PF CT CAP, CHIP TYPE TRIMMER 10PF < DIODE > D DIODE 1T362 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SR TE-25 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS226 < IC > IC IC TA31136FN IC IC CXA1111N IC IC TC75S51F-TE85L IC IC TC4066BFS IC IC TC4066BFS IC IC TC75S51F-TE85L IC IC CXA1522N IC IC RN5RG40AA-TL IC IC NJM2360AM(TE2) IC IC RN5RL40AA-T1 < JACK > J JACK J JACK,DC(POLARITY UNIFIED TYPE) (DC IN 6V) < COIL > L INDUCTOR 4.7uH L COIL (WITH CORE) L INDUCTOR 2.2uH L INDUCTOR 0.22uH L INDUCTOR 33uH L INDUCTOR 0.33uH L FILTER, COMMON MODE L INDUCTOR 390uH Q TRANSISTOR 2SB815B7-TB Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SC4177 Q TRANSISTOR 2SC4177 Q TRANSISTOR 2SB815B7-TB Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SA1745 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SA1745 < RESISTOR > R METAL CHIP 820 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 330K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 6.8K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 470K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 33K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 4.7K 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 10 5% 1/16W 37

27 IF MICROCOMPUTER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R METAL CHIP 0 5% 1/16W R METAL CHIP 4.7K 5% 1/16W R METAL CHIP 68K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 4.7K 5% 1/16W < VIBRATOR > XF FILTER, CRYSTAL XF FILTER, CRYSTAL ************************************************************ R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 18K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 27K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 33K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 4.7K 5% 1/16W R METAL CHIP 4.7K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 2.2 5% 1/16W R RES,CHIP 4.7 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 6.8K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 1.5K 5% 1/16W R METAL CHIP 330 5% 1/16W R METAL CHIP 220 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 5.6K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W < VARIABLE RESISTOR > RV RES, ADJ, CERMET 100K (3rd LOCAL OSCILLATOR) RV RES, VAR, CARBON 10K (SQL) RV RES, ADJ, CERMET 10K (AGC) RV RES, VAR, CARBON 50K (VOL) < VIBRATOR > X VIBRATOR, CRYSTAL (44.545MHz) X VIBRATOR, CRYSTAL (34.3MHz) * A A MICROCOMPUTER BOARD, COMPLETE * A A MICROCOMPUTER BOARD, COMPLETE (SC1) ****************************** CONDUCTIVE BOARD, CONNECTION PLATE, LIGHT GUIDE CASE (LCD) * SPACER (B) < CAPACITOR > C CERAMIC CHIP 0.01uF 10% 25V C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 0.01uF 10% 25V C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.001uF 10% 50V C TANTAL. CHIP 100uF 20% 6.3V C TANTAL. CHIP 100uF 20% 6.3V C TANTAL. CHIP 100uF 20% 6.3V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 27PF 5% 50V C TANTAL. CHIP 22uF 20% 6.3V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 1uF 10V C TANTAL. CHIP 10uF 20% 6.3V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.01uF 10% 25V 38

28 MICROCOMPUTER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C CERAMIC CHIP 0.01uF 10% 25V C TANTAL. CHIP 1uF 20% 35V C TANTAL. CHIP 1uF 20% 35V C CERAMIC CHIP 1uF 10V C TANTAL. CHIP 1uF 20% 35V C TANTAL. CHIP 1uF 20% 35V C TANTAL. CHIP 1uF 20% 35V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 27PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V D DIODE MA8180 D DIODE MA8180 D DIODE MA8180 D DIODE MA8180 D DIODE MA8180 D DIODE MA8180 < IC > IC IC RN5RL40AA-T1 IC IC RN5VT20AA-TL IC IC RN5VL42AA-TL IC IC upd78064bgc-a08-8eu IC IC AT25160N-10SC2.7T2.5 IC IC RN5RL30AA-TL IC IC upd4721gs-gjg-e2 < COIL > L INDUCTOR 1uH L INDUCTOR 0.1uH L INDUCTOR 0.1uH L INDUCTOR 0.1uH L INDUCTOR 0.1uH L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 10uH C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 100PF 5% 50V < CONNECTOR > CN CONNECTOR, FFC/FPC (ZIF) 22P CN CONNECTOR, MINIATURE DIN 8P (SERIAL IOIOI) < DIODE > D DIODE RB501V-40TE-17 D DIODE 1SS355 D DIODE CL-181G-C D DIODE CL-181G-C D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 D DIODE 1SS355 D DIODE MA8180 D DIODE MA8180 L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 10uH L INDUCTOR 0.1uH LCD < LIQUID CRYSTAL DISPLAY > DISPLAY PANEL, LIQUID CRYSTAL < TRANSISTOR > Q TRANSISTOR 2SA1745 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SC4177 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR DTC144EUA-T106 < RESISTOR > R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 330 5% 1/16W R METAL CHIP 330 5% 1/16W R METAL CHIP 4.7k 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 20K 0.50% 1/16W R METAL CHIP 10K 0.50% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 1K 5% 1/16W 39

29 MICROCOMPUTER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R METAL CHIP 1K 5% 1/16W R METAL CHIP 20K 0.50% 1/16W R METAL CHIP 20K 0.50% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 330K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 330 5% 1/16W R METAL CHIP 330 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 10K 5% 1/16W R METAL CHIP 1M 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W < SWITCH > S SWITCH, TACTIL (POWER) S SWITCH, KEY BOARD (LIGHT/H) < VIBRATOR > X VIBRATOR, CRYSTAL (32.768kHz) X VIBRATOR, CERAMIC ( MHz) ************************************************************ R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1M 5% 1/16W 40

30 RF Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * A A RF BOARD, COMPLETE ****************** C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 0.001uF 10% 50V < CAPACITOR > C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 33PF 5% 50V C CERAMIC CHIP 33PF 5% 50V C CERAMIC CHIP 82PF 5% 50V C CERAMIC CHIP 12PF 5% 50V C CERAMIC CHIP 47PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 7PF 0.5PF 50V C CERAMIC CHIP 12PF 5% 50V C CERAMIC CHIP 7PF 0.5PF 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 68PF 5% 50V C CERAMIC CHIP 7PF 0.5PF 50V C CERAMIC CHIP 5PF 0.25PF 50V C CERAMIC CHIP 68PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 6PF 0.5PF 50V C CERAMIC CHIP 6PF 0.5PF 50V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 4PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1PF 0.25PF 50V C CERAMIC CHIP 4PF 0.25PF 50V C CERAMIC CHIP 4PF 0.25PF 50V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 4PF 0.25PF 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 15PF 5% 50V C CERAMIC CHIP 5PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 9PF 0.5PF 50V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 9PF 0.5PF 50V C CERAMIC CHIP 4PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 22PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 1.5PF 0.25PF 50V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 33PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 24PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 12PF 5% 50V C CERAMIC CHIP 15PF 5% 50V C CERAMIC CHIP 0.1uF 10% 16V C TANTAL. CHIP 100uF 20% 6.3V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 0.1uF 10% 16V C CERAMIC CHIP 1uF 10V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.022uF 10% 25V C FILM 1uF 5% 63V C TANTAL. CHIP 1uF 20% 35V C TANTALUM CHIP 0.33uF 10% 35V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1PF 0.25PF 50V 41

31 RF Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 5PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C TANTAL. CHIP 100uF 20% 6.3V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V < TRIMMER > CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 10PF CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 5PF CT CAP, CHIP TYPE TRIMMER 5PF C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 3PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C TANTAL. CHIP 100uF 20% 6.3V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 15PF 5% 50V C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 27PF 5% 50V C CERAMIC CHIP 27PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.01uF 10% 25V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 0.001uF 10% 50V C CERAMIC CHIP 10PF 0.5PF 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 1PF 0.25PF 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 1PF 0.25PF 50V C CERAMIC CHIP 8PF 0.5PF 50V C CERAMIC CHIP 2PF 0.25PF 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 1000PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V C CERAMIC CHIP 100PF 5% 50V < CONNECTOR > CN CONNECTOR, FFC/FPC (ZIF) 16P < DIODE > D DIODE 1SS226 D DIODE MA77 D DIODE MA78-TX D DIODE MA78-TX D DIODE MA78-TX D DIODE MA77 D DIODE MA77 D DIODE MA78-TX D DIODE MA77 D DIODE MA77 D DIODE MA78-TX D DIODE MA78-TX D DIODE MA77 D DIODE MA77 D DIODE MA80WK-TX D DIODE HSM276S D DIODE HSM276S D DIODE MA80WK-TX D DIODE MA80WK-TX D DIODE MA80WK-TX D DIODE 1T T8A D DIODE 1T T8A D DIODE MA80WK-TX D DIODE MA77 D DIODE MA80WK-TX D DIODE MA8051 D DIODE MA8051 < IC > IC IC TC74VHC595FS(EL) IC IC MB1511-PFV-EF < COIL > L INDUCTOR 0.12uH L INDUCTOR 0.18uH L INDUCTOR 22NH L INDUCTOR 22NH L INDUCTOR 22NH L INDUCTOR 220NH L INDUCTOR 22NH L INDUCTOR 6.8NH L INDUCTOR 12NH L INDUCTOR 4.7NH L INDUCTOR 8.2NH L INDUCTOR 15NH 42

32 RF Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L INDUCTOR 8.2NH L INDUCTOR 15NH L INDUCTOR 6.8NH L INDUCTOR 3.3uH L INDUCTOR 33NH L INDUCTOR 0.1uH L INDUCTOR 33NH L INDUCTOR 33NH L INDUCTOR 33NH L INDUCTOR 15NH L INDUCTOR 22NH L INDUCTOR 10NH L INDUCTOR 0.1uH L INDUCTOR 0.1uH L INDUCTOR 33NH L INDUCTOR 10NH L INDUCTOR 15NH L INDUCTOR 15NH L INDUCTOR 68NH L INDUCTOR 1uH L INDUCTOR 22NH L INDUCTOR 22NH L INDUCTOR 22NH < TRANSISTOR > Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC5012(R37)-T1 Q TRANSISTOR 2SC5012(R37)-T1 Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR DTA114TUA-T106 Q TRANSISTOR DTA114TUA-T106 Q TRANSISTOR DTA114TUA-T106 Q TRANSISTOR DTA114TUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SA1611-M5M6 Q TRANSISTOR 2SA1611-M5M6 Q TRANSISTOR 2SK880GR-TE85L Q TRANSISTOR 2SC4177 Q TRANSISTOR 2SK880GR-TE85L Q TRANSISTOR DTA114TUA-T106 Q TRANSISTOR DTC144EUA-T106 Q TRANSISTOR 2SC5012(R37)-T1 Q TRANSISTOR 2SC5012(R37)-T1 Q TRANSISTOR 2SC4182-T2T33 Q TRANSISTOR 2SC5012(R37)-T1 Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) Q TRANSISTOR 2SC4226(R24) R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 47K 5% 1/16W R METAL CHIP 100 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 33K 5% 1/16W R METAL CHIP 0 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 68K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 2.2K 5% 1/16W R METAL CHIP 220K 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 220K 5% 1/16W R METAL CHIP 820 5% 1/16W R METAL CHIP 47 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 1K 5% 1/16W R METAL CHIP 33K 5% 1/16W R METAL CHIP 100K 5% 1/16W R METAL CHIP 220K 5% 1/16W < RESISTOR > R METAL CHIP 1K 5% 1/16W R METAL CHIP 10 5% 1/16W R METAL CHIP 33K 5% 1/16W R METAL CHIP 100K 5% 1/16W 43