Induct. Inductive proximity sensors. Inductive sensors. Double sensing range. Triple sensing range. Single sensing range. Flush installation

Transcription

1 Inductive sensors Inductive proximity sensors Single sensing range Double sensing range Triple sensing range Flush installation Cylinder housing Threaded cylinder housing Cuboid housing Non-flush installation Induct 00 SENSICK CATALOGUE

2 Contents Inductive proximity sensors General page 0 Operating principle page 0 Glossary page 05 Installation notes page 0 Selection table page Type code page 5 I series I 0 page 6 I 05 page 8 I 08 (incl. ATEX) page 0 I (incl. ATEX) page 8 I 8 (incl. ATEX) page 66 I 0 (incl. ATEX) page 9 IH series IH 0 page IH 0 page IH 06 page 6 IH 0 page IH page IQ series IQ 05 page 6 IQ 08 page 8 IQ 0 page 0 IQ page IQ 0 page IQ 80 page 50 ive proximity sensors SENSICK CATALOGUE 0

3 Inductive Sensors Set the standards in your industry. Ready to meet the requirements of factory automation. any type options Individual switching distances IP 67/68 enclosure rating Co-ordinated with individual customer requirements, SICK inductive sensors enable the implementation of industry-specific automation solutions, increasing productivity with a high degree of reliability. Vibration resistant Ex-area/ ATEX approval AC/DC version High EC resistance any different designs For difficult, small objects TRIPLEX inductive sensors with triple switching distance. With this innovation in metric design, SICK devices set new standards in scanning range and machine availability. The TRIPLEX Series provides you with one of the largest switching distances to metal targets, currently available. mm switching distance and quasi-flush mounting of the I 08 design up to 0 mm, with non-flush mounting of the I 0 design, enable a greater fitting distance guaranteeing more protection from mechanical damage. TRIPLEX offers you best results, with even greater positioning tolerances for small, difficult to detect objects. IX Series sensor solution with IP 69K protection and VA stainless steel construction for the food and beverage industry. Wet areas of food production facilities and bottling plants are harsher than anywhere else: pressures from -00 bar, high temperatures, acids, lyes and cleaning agents significantly affect many a sensor and signal. The IX Series inductive sensors, however, have virtually no weaknesses. Types I, I 8 and I 0 are available to detect objects. A particular feature of the sensors is the triple switching distance, the IP 69K enclosure rating, as well as the fully encapsulated housing in VA stainless steel resulting in long life of the SICK sensors and reliable signal transmission. 0 SENSICK KATALOG

4 Simple and flexible installation. illions of inductive sensors are used in practically all areas of factory automation. The SICK range offers you many sensors for different mounting requirements: choice of or NC function, with NPN or PNP switching output, cable or plugin sensor connection, standard or short body housings as well as integrated mounting rail brackets and device plug with 60 rotation. In brief: SICK inductive sensors make the use and connection of sensors particularly easy and convenient. Robust and long lasting. High-quality workmanship, robust metal or plastic housings ensure long life and high-precision switching. The sensors are highly reliable even in arduous operating conditions, withstanding vibration/shock, coolants/lubricants or high temperature variations, moisture or electromagnetic interference etc. eeting current and future market requirements. Reducing error rates, eliminating quality defects and optimising processes. Whether for positional tasks, transport monitoring or muting safety guards SICK inductive sensors are used wherever reliable detection of metallic objects is required. Inductive solutions in all types. Inductive metric design I Inductive sleeve design IH Inductive cuboid design IQ SENSICK KATALOG 0

5 Inductive proximity sensors O p e r a t i n g p r i n c i p l e An inductive proximity sensor comprises an LC oscillating circuit, a signal evaluator, and a switching amplifier. Alternating field Sensing face L C Attenuating material LC oscillating circuit Signal evaluator Switching amplifier The coil of this oscillating circuit generates a high-frequency electromagnetic alternating field. This field is emitted at the sensing face of the sensor. If attenuating material nears the sensing face, eddy currents are generated in the case of non-ferrite metals. In the case of ferromagnetic metals, hysteresis and eddy-current loss also occurs. These losses draw energy from the oscillating circuit and reduce oscillation. The signal evaluator detects this reduction and converts it into a switching signal. The terms attenuated and unattenuated are used to describe the two switching states of the inductive proximity sensors. Switching trigger I attenuated unattenuated s n U 0 SENSICK CATALOGUE

6 Inductive proximity sensors O p e r a t i n g p r i n c i p l e Response curve for inductive proximity sensors The specified sensing ranges are determined in the case of axial approach along the reference axis of the sensor. Radial approach results in a reduction of the sensing range. The edge of the switching trigger has only a small surface area. As a result, less eddy-current losses occur. The sensor therefore only reacts if the switching trigger laterally enters the alternating field relatively close to the sensing face. In the case of axial approach, the full surface of the switching trigger is exposed to the scattered electromagnetic field. Axial alignment therefore provides the maximum sensing range. Axial approach direction Reliable operating range Hysteresis Radial approach direction Proximity sensor G l o s s a r y Active switching zone Area above the sensing face in which a proximity sensor responds by a change in switching status when attenuating material is brought nearer. Adjustment aid (optical) inductive proximity sensor IX Optical adjustment aid per LED allows for quick alignment and optical usage of increased sensing range. LED indicator flashes during % of rated sensing range and proceeds to permanent display reaching the secured sensing range (8%). Default setting (practice): LED lights continuously Setting via adjustment aid: Standard sensing range LED lights continuously Increased sensing range: secure sensing range LED blinks Sensing range 8 00 [%] Increased sensing range: insecure sensing range Complementary output A DC -wire with one and NC output that can be used at the same time SENSICK CATALOGUE 05

7 Inductive proximity sensors G l o s s a r y Current at which the proximity sensor can function reliably. Flush installation A proximity sensor can be embedded in an attenuating material so that it is flush with the active surface. inimum load current Smallest load current that must flow with connected output in order to ensure the reliable operation of -wire proximity sensors. Non-flush installation A proximity sensor must be installed in such a way that a free-zone is maintained. NPN output Proximity sensors with NPN output switch the negative potential to the load. They are also described as negative-switching or current-sinking. + Load Output Operating voltage U b Voltage range in which the proximity sensor can function reliably. Output function Normally open: A proximity sensor with make function is disabled in the unattenuated state (high resistance) and is switched in the attenuated state (low resistance). Normally closed : A proximity sensor with brake function is switched in the unattenuated state (low resistance)and disabled in the attenuated state (high resistance). 06 SENSICK CATALOGUE

8 Inductive proximity sensors G l o s s a r y Overload resistance See also short-circuit protection. The response threshold for overload protection is greater than the value for continuous current-carrying capacity. Peak current I r Current that may flow for a specified period at a defined switching frequency without destroying the proximity sensor. PNP output Proximity sensors with PNP output switch the positive potential to the load. They are also described as positive-switching or current-sourcing. + Output Load Power-up pulse suppression The power-up pulse suppression ensures that no incorrect switching signal is sent to the output between the time when the operating voltage is applied and when the oscillator begins to oscillate. Rated switching trigger All sensing range measurements must be performed by axially moving a standard square measuring plate made of St7 ( mm thick) through the alternating field. The length of the switching trigger sides is equal to the diameter of the response area or is s n. The larger value should be taken. Reduction factor R The specified sensing ranges all relate to St7. Considerable reductions in distance sometimes occur in the case of other materials. Approximate reference values, which can vary from type to type: St7 (Fe) Stainless steal (VA) 0.8 Aluminium (solid) 0.5 Copper (Cu) Fe VA Al Cu 0 These correction factors must be taken into consideration when selecting actuation elements or when calibrating to objects made of the respective alloys. When proximity sensors are installed, the reliable sensing range (8 % of s n ) should always be used as the basis. The exact switching point must be set by means of fine adjustment SENSICK CATALOGUE 07

9 Inductive proximity sensors G l o s s a r y Residual current I r The residual current is used to supply power to the -wire sensors and also flows across the load if the output is disabled. Reverse polarity protection An internal protection circuit prevents the DC /-wire proximity sensors from being destroyed if the supply voltage connections are incorrectly connected, and also ensures that no misoperation can occur which would result in an undesired signal being issued. Ripple V PP The DC operating voltage of the ripple voltage content (maximum permissible peak value, given in % of U b ). U Ub V PP t Sensing face Surface of a proximity sensor to which the sensing range relates. Sensing range The sensing range of a proximity sensor is the distance at which one of the measuring plates being moved axially towards the active surface triggers a signal change. s u max. s r max. s n s r min. s u min. easuring plate. s n. s n s r s u 0.9 s n 0.8 s n Sensing face sa Proximity sensor Rated sensing range s n : Device characteristics Real sensing range s r : 0.9 s n s r. s n Useful sensing range s u : 0.9 s r s u. s r Actuation distance s a : The actuation distance is the distance at which a proximity sensor reacts under specified temperature and voltage conditions. It is between 0 % and 8 % of the rated sensing range. Shock stress Pulse shape: Acceleration: Pulse length: semi-sinoidal 0 g n ms 08 SENSICK CATALOGUE

10 Inductive proximity sensors G l o s s a r y Short-circuit protection (with NAUR sensor to EN 507) The proximity sensor is not destroyed if the load short-circuits or in the case of a short-circuit to ground at the output. Short-circuit protection Proximity sensors with short-circuit protection cannot be destroyed by either overloading or a direct short-circuit. When the triggering threshold is exceeded, the output is disabled and then periodically (in cycles) polled to establish whether the short-circuit still exists. An automatic reset is performed once the short-circuit has been eliminated. Switching frequency f aximum number of switching actions per second. Proximity sensor a a sn easuring plate Disk Time delay before availability t V Time required by the proximity sensor to become operational after the operating voltage is applied. Vibrations stress Frequency range: Amplitude: Vibration length: Endurance at resonance frequency or at 55 Hz: 0 to 55 Hz mm 5 min 0 min in each axis Voltage drop U d (at I a max) Reduction in voltage occurring at maximum load current across the switching module of the proximity sensor. Special attention must be paid to this in the case of serial connections. Wire-break protection If one of the supply lines is broken, the output remains disabled (no misoperation) SENSICK CATALOGUE 09

11 Inductive proximity sensors In s t a l l a t i o n n o t e s Flush installation in metal Proximity sensors for flush installation are shielded internally around the ferrite core. As a result, the sensor can be embedded in the metal up to the sensing face. Proximity sensors for flush installation have a smaller sensing range compared to proximity sensors for non-flush installation with the same shape and design. Quasi-flush installation in metal These sensors with increased sensing range cannot be totally flush-mounted in metal but can be quasi-flush mounted with the free zone specified. Advanced series Type I-0B... I8-08B... I0-5B... IH06-0B... etal-free zone 0. x d 0. x d 0. x d mm Triplex series Type I08-0B... I-06B... I8-B... I0-B... etal-free zone mm (St 7) mm (St 7) mm (St 7) 6 mm (St 7) Non-flush installation in metal With proximity sensors for non-flush installation, a metal-free zone must be maintained owing to the scattered field distribution. Cylindrical design General installation notes for cylindrical design for flush and non-flush installation in metal: d d d d d d d Sn Sn Sn Flush installation Non-flush installation Opposite installation 8 S n 0 SENSICK CATALOGUE

12 Inductive proximity sensors In s t a l l a t i o n n o t e s Cylindrical type Triplex Series General installation notes for cylindrical types, for quasi-flush and non-flush installation in metal: A B A B S n (C) S n (C) D Quasi-flush installation Non-flush installation Quasi-flush installation Type etal-free zone: x A x C I08... A = mm, B = 8 mm, C = 9 mm I... A = 6 mm, B = 8 mm, C = 8 mm I8... I0... A = mm, B = 6 mm, C = 6 mm A = 0 mm, B = 50 mm, C = 66 mm Non-flush installation Type I08... I... I8... I0... etal-free zone: x A x (C + D) A = mm, B = 0 mm, C = 8 mm, D = mm A = 8 mm, B = 0 mm, C = 0 mm, D = 0 mm A = 7 mm, B = 60 mm, C = 60 mm, D = 0 mm A = 5 mm, B = 0 mm, C = 0 mm, D = 80 mm Cylindrical type IX Series General installation notes for cylindrical design for flush and non-flush installation in metal: A A B B S n (C) S n (C) D Flush installation Flush installation Type I... I8... I0... etal-free zone: x A x C A = mm, B = 0 mm, C = 8 mm A = 5 mm, B = 60 mm, C = 0 mm A = 5 mm, B = 90 mm, C = 60 mm Non-flush installation Non-flush installation Type I... I8... I0... etal-free zone: x A x (C + D) A = 0 mm, B = 80 mm, C = 0 mm, D = 0 mm A = 50 mm, B = 50 mm, C = 60 mm, D = 5 mm A = 90 mm, B = 50 mm, C = 0 mm, D = 60 mm Rated switching trigger Flush installation Type I... easuring plate 8 x 8 mm Non-flush installation Type I... easuring plate 0 x 0 mm I x 0 mm I x 60 mm I x 60 mm I x 0 mm SENSICK CATALOGUE

13 Inductive proximity sensors In s t a l l a t i o n n o t e s Operating distance s r as a function of material thickness IX version, flush installation IX 0 version, non-flush installation 0 50 s n Brass Steel Steel Brass s n sr [mm] 6 5 Aluminium Stainless steel sr [mm] Stainless steel Aluminium Thickness [mm] 0 0,5 0 0 Thickness [mm] Operating distance s r as a function of surface IX version, flush installation IX 0 version, non-flush installation s r [mm] 6 S n 5 Rated switching trigger sr [mm] Rated switching trigger S n Side length [mm] Side length [mm] Operating distance s r as a function of length/width IX version, flush installation IX 0 version, non-flush installation sr [mm] 8 7 S n 6 5 Rated switching trigger Shorter side [mm] s r [mm] 5 0 S n Rated switching trigger Shorter side [mm] SENSICK CATALOGUE

14 8 x S n Inductive proximity sensors In s t a l l a t i o n n o t e s Cuboidal design General installation notes for cuboidal design in metal: Non-flush installation Z Z D Y X Design IQ0-5B IQ0-0B IQ0-0N IQ0-5N X [mm] Y [mm] Z [mm] Non-flush installation Ø Ø Ø6 0 8 Design IQ08-0B... IQ08-0N... IQ0-0B... IQ0-06N... IQ-0B... IQ-06N... Y [mm] Opposite installation SENSICK CATALOGUE

15 Inductive proximity sensors Selection table Series Housing Sensing range S n in mm I 0 I 05 I 08 I I 8 I 0 I I 8 I 0 IH 0 IH 0 IH 06 IQ 05 IQ 08 IQ 0 IQ IQ 0 IQ 0 IQ 0 IQ 80 IQ 80 I I 8 I 0 IQ 0 I I 8 I 0 IH 0 IH IQ 0 IQ 0 IQ 80 I 08 I I 8 I 0 Cylinder with thread, Brass 0.6 DC -w. 6 5, Brass 0.8 DC -w. 8 8, Brass.5//.5//6 DC -w. 0, Brass //6 /8/0 DC /-w. 8 8, Brass 5/8/ 8//0 DC /-w. 66 0, Brass 0/5/ 5/0/0 DC -w. 9 Cylinder with thread IX series, Stainless steel VA 6 0 DC -w. 5 8, Stainless steel VA 0 0 DC -w. 80 0, Stainless steel VA 0 0 DC -w. 0 Barrel, smooth Ø, Stainless steel 0.6 DC -w. Ø, Stainless steel 0.8 DC -w. Ø 6,5, Stainless steel.5/ DC -w. 6 Cuboid 5x5x5, Brass 0.8 DC -w. 6 8x0/8x9, Plastic DC -w. 8 0x8/6x7, Plastic 6 DC -w. 0 x0/6x9, Plastic 6 DC -w. xx, Plastic 5 0 DC -w. 0x0x8, Plastic 5 0 DC -w. 8 0x0x66, Plastic 5/0 5 DC /-w. 6 80x0x05, Plastic 60 80x0x, Plastic 50 (+over-flush).5 DC -w. 5 Cylinder with thread, Brass DC -w. 60 8, Brass 5 8 DC -w. 86 0, Brass 0 5 DC -w. 06 Cuboid Cylinder with thread, Brass AC 6 8, Brass 5 8 AC/DC 88 0, Brass 0 5 AC/DC 08 Barrel, smooth Ø 0, Plastic 0 AC/DC Ø, Plastic 0 AC/DC Cuboid xx, Plastic 5 0 AC/DC 8 80x0x05, Plastic 60 AC/DC 5 Cylinder with thread Switching output Output function Connction type Design, size in mm, material Flush Non-flush P ) N ) NC /NC ) C ) Co. 5) T 6) Electr. config. DC -w. 50 0x0x8, Plastic 5 DC -w. 0x0x8, Plastic 5 AC -w. 6 8, Brass NAUR 6, Brass NAUR 6 8, Brass 5 8 NAUR 90 0, Brass 0 5 NAUR 0 From page ) P = PNP ) N = NPN ) /NC = progr./compl. ) C = Cable 5) Co. = Connector 6) T = Terminals SENSICK CATALOGUE

16 Inductive proximity sensors Type code I 0B P S Z U 0 Sensor technology Other codes Inductive I K Short body housing Design 0 Standard Barrel H Standard Cylinder with thread Cables and connectors Cuboid Housing shape, diameter or edge dimension on the sensing face Q W U P Cable, PVC Cable, PUR-PVC Cable with connector, 8 x 0 0 T Connector, 8 x 0 0 C Connector, x K Terminals Housing material Z S, nickel-plated 0 0 V Stainless steel K Plastic 8 8 N Stainless steel VA (IX series) 0 0 Output 0 0 S O NC 0 0 P Programmable/complementary N NAUR Sensing range/installation Interface Flush B P DC (/-wire) PNP Non-flush N N DC (/-wire) NPN mm, flush 0B C DC (-wire) PNP or NPN mm, non-flush 0N D DC -wire.5 mm, flush B5 A AC -wire.5 mm, non-flush N5 U AC/DC -wire NAUR SENSICK CATALOGUE 5

17 Inductive sensor, I0, DC -wire, iniature series, Flush Inductive sensor Sensing range 0.6 mm Can be installed flush High switching frequency Short-circuit protection (pulsed) Robust stainless steel housing with fine thread x 0.5 mm Enclosure rating IP 67 Dimensional drawing 6 9 x0.5 Connection Display LED Fastening nuts ( x); width across 6, stainless steel I0-0B6NS-ZU I0-0B6PS-ZU x 0.06 mm² 6 SENSICK CATALOGUE

18 I0 Technical specifications I0-0B6NS -ZU 0B6PS -ZU Sensing range S n Electrical configuration 0.6 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d 0.6 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 % % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PUR, m 5,000 Hz Dimensions x 0.5 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a = 50 ma Stainless steel, plastic 0.8 Nm ) without load ) normally closed function available on request 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I0-0B6NS-ZU I0-0B6PS-ZU SENSICK CATALOGUE 7

19 Inductive sensor, I05, DC -wire, iniature series, Flush Inductive sensor Sensing range 0.8 mm Can be installed flush High switching frequency Short-circuit protection (pulsed) Robust stainless steel housing with fine thread 5 x 0.5 mm Enclosure rating IP 67 Dimensional drawing x0.5 5x0.5 Connection Display LED Fastening nuts ( x); width across 7, stainless steel I05-0B8NS-ZT I05-0B8NS-ZW I05-0B8-ZW I05-0B8PS-ZT I05-0B8PS-ZWB I05-0B8PS-ZW See chapter Accessories Connector, 8, -pin 8, -pin x 0. mm² x 0. mm² NC 8 SENSICK CATALOGUE

20 I05 Technical specifications I05-0B8 -ZW 0B8NS -ZT 0B8NS -ZW 0B8PS -ZT 0B8PS -ZWB 0B8PS -ZW Sensing range S n Electrical configuration 0.8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 %.5 % (U b and T a constant) EC According to EN Switching output Output function Installation NPN PNP Normally closed Normally open Flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector, 8, -pin Cable, PVC, 5 m 5,000 Hz Dimensions 5 x 0.5 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a = 00 ma Stainless steel, plastic.5 Nm ) without load ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I05-0B8-ZW I05-0B8NS-ZT I05-0B8NS-ZW I05-0B8PS-ZT I05-0B8PS-ZWB I05-0B8PS-ZW SENSICK CATALOGUE 9

21 Inductive sensor, I08, DC -wire, Standard series, Flush Inductive sensor Sensing range.5 mm High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel- Dimensional drawing x plated with fine thread 8 x mm Enclosure rating IP x x 60 Connection Display LED Fastening nuts ( x); width across, metal I08-B5-ZW I08-B5NS-ZT I08-B5NS-ZC I08-B5NS-ZW I08-B5PO-ZT I08-B5PS-ZC I08-B5PO-ZW I08-B5PS-ZT I08-B5PS-ZW See chapter Accessories Connector,, -pin Connector, 8, -pin x 0. mm² 8, -pin, -pin /NC 0 SENSICK CATALOGUE

22 I08 Technical specifications I08- B5 -ZW B5NS -ZW B5PO -ZW B5PS -ZW B5NS -ZC B5NS -ZT B5PO -ZT B5PS -ZC B5PS -ZT Sensing range S n Electrical configuration.5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally closed Normally open Flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector,, -pin Connector, 8, -pin,000 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I08-B5-ZW I08-B5NS-ZW I08-B5PO-ZW I08-B5PS-ZW I08-B5NS-ZC 6 00 I08-B5NS-ZT I08-B5PO-ZT 6 00 I08-B5PS-ZC 6 00 I08-B5PS-ZT SENSICK CATALOGUE

23 Inductive sensor, I08, DC -wire, Standard series, Non-flush Inductive sensor Sensing range.5 mm High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickelplated with fine thread 8 x mm Dimensional drawing x Enclosure rating IP 67. 8x 50 8x 60 Connection Display LED Fastening nuts ( x); width across, metal I08-N5NS-ZW I08-N5PS-ZW I08-N5NS-ZT I08-N5PS-ZT I08-N5NS-ZC I08-N5PS-ZC See chapter Accessories Connector,, -pin Connector, 8, -pin x 0. mm² 8, -pin, -pin SENSICK CATALOGUE

24 I08 Technical specifications I08- N5NS -ZW N5PS -ZW N5NS -ZC N5NS -ZT N5PS -ZC N5PS -ZT Sensing range S n Electrical configuration.5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Non-flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector,, -pin Connector, 8, -pin,500 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I08-N5NS-ZW I08-N5PS-ZW I08-N5NS-ZC I08-N5NS-ZT 6 00 I08-N5PS-ZC I08-N5PS-ZT SENSICK CATALOGUE

25 Inductive sensor, I08, DC -wire, Short version, Flush Inductive sensor Sensing range.5 mm High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickelplated with fine thread 8 x mm Enclosure rating IP 67 Dimensional drawing 6 9 8x 8x Connection Display LED Fastening nuts ( x); width across, metal I08-B5NS-ZWK I08-B5PS-ZWK I08-B5NS-ZTK I08-B5PS-ZTK See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin SENSICK CATALOGUE

26 I08 Technical specifications I08- B5NS -ZWK B5PS -ZWK B5NS -ZTK B5PS -ZTK Sensing range S n Electrical configuration.5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 % 5 % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector, 8, -pin 5,000 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a = 00 ma Brass nickel-plated, plastic Nm ) without load ) normally closed function available on request 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I08-B5NS-ZWK I08-B5PS-ZWK 6 00 I08-B5NS-ZTK I08-B5PS-ZTK SENSICK CATALOGUE 5

27 Inductive sensor, I08, DC -wire, Advanced series, Flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Dimensional drawing x Robust brass housing, nickelplated with fine thread 8 x mm Enclosure rating IP x 50 Connection Display LED Fastening nuts ( x); width across, metal I08-0BNS-ZW I08-0BPO-ZW I08-0BPS-ZW I08-0B-ZT I08-0BNS-ZT I08-0BPS-ZT I08-0BPO-ZT See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin /NC 6 SENSICK CATALOGUE

28 I08 Technical specifications I08-0BNS -ZW 0BPO -ZW 0BPS -ZW 0B -ZT 0BNS -ZT 0BPS -ZT 0BPO -ZT Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector, 8, -pin,000 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Ambient temperature T a Housing material Tightening torque ) of U b ) at I a max 7) 0 g, ms/ Hz, mm -5 C C Brass nickel-plated, plastic Nm ) 5) without load according to EN 6059 ) 6) of s r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I08-0BNS-ZW I08-0BPO-ZW I08-0BPS-ZW I08-0B-ZT I08-0BNS-ZT I08-0BPS-ZT I08-0BPO-ZT SENSICK CATALOGUE 7

29 Inductive sensor, I08, DC -wire, Advanced series, Non-flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel- Dimensional drawing x plated with fine thread 8 x mm Enclosure rating IP 67. 8x 50 Connection Display LED Fastening nuts ( x); width across, metal I08-0NNS-ZW I08-0NPO-ZW I08-0NPS-ZW I08-0N-ZT I08-0NNS-ZT I08-0NPO-ZT I08-0NPS-ZT See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin /NC 8 SENSICK CATALOGUE

30 I08 Technical specifications I08-0NNS -ZW 0NPO -ZW 0NPS -ZW 0NN O-ZT 0NNS -ZT 0NPO -ZT 0NPS -ZT Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector, 8, -pin,800 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic Nm ) 5) without load according to EN 6059 ) 6) of s r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I08-0NNS-ZW I08-0NPO-ZW I08-0NPS-ZW I08-0N-ZT I08-0NNS-ZT I08-0NPO-ZT I08-0NPS-ZT SENSICK CATALOGUE 9

31 Inductive sensor, I08, DC -wire, Advanced short series, Flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Dimensional drawing x Robust brass housing, nickelplated with fine thread 8 x mm Enclosure rating IP x Connection Display LED Fastening nuts ( x); width across, metal I08-0BNS-ZWK I08-0BPS-ZWK I08-0BPS-ZUA I08-0BNS-ZTK I08-0BPO-ZTK I08-0BPS-ZTK I08-0B-ZTK See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin /NC 0 SENSICK CATALOGUE

32 I08 Technical specifications I08-0BNS -ZWK 0BPS -ZWK 0BPS -ZUA 0BNS -ZTK 0BPO -ZTK 0BPS -ZTK 0B -ZTK Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 5 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Cable, PUR, m Connector, 8, -pin,000 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic Nm ) without load ) of s r 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I08-0BNS-ZWK I08-0BPS-ZWK I08-0BPS-ZUA I08-0BNS-ZTK I08-0BPO-ZTK I08-0BPS-ZTK I08-0B-ZTK SENSICK CATALOGUE

33 Inductive sensor, I08, DC -wire, Advanced short series, Non-flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickelplated with fine thread 8 x mm Enclosure rating IP 67 Dimensional drawing x 8x Connection Display LED Fastening nuts ( x); width across, metal I08-0NPS-ZWK I08-0NNS-ZWK I08-0NPS-ZTK I08-0N-ZTK I08-0NNS-ZTK I08-0NPO-ZTK See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin /NC SENSICK CATALOGUE

34 I08 Technical specifications I08-0NPS -ZWK 0NNS -ZWK 0NPS -ZTK 0NN O-ZTK 0NNS -ZTK 0NPO -ZTK Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 5 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP NPN Normally open Normally closed Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector, 8, -pin,500 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic Nm ) 5) without load according to EN 6059 ) 6) of s r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I08-0NPS-ZWK I08-0NNS-ZWK I08-0NPS-ZTK I08-0N-ZTK I08-0NNS-ZTK I08-0NPO-ZTK SENSICK CATALOGUE

35 Inductive sensor, I08, DC -wire, Triplex series Inductive sensor Sensing range / 6 mm Triple sensing range Installation quasi flush or non-flush in metal Dimensional drawing x Short-circuit protection (pulsed) Robust brass housing, chromeplated with fine thread 8 x mm Enclosure rating IP x 0 5 8x x 60 Connection Display LED Fastening nuts ( x); width across, metal I08-0BPS-ZW I08-06NNS-ZW I08-06NPS-ZW I08-0BPS-ZT I08-06NPS-ZT See chapter Accessories Connector, 8, -pin x 0. mm² 8, -pin SENSICK CATALOGUE

36 I08 Technical specifications I08-0BPS -ZW 0BPS -ZT 06NNS -ZW 06NPS -ZW 06NPS -ZT Sensing range S n Electrical configuration mm 6 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output PNP NPN Output function Normally open 5) Installation Quasi-flush 6) Non-flush Enclosure rating IP 67 7) ax. switching frequency Cable, PVC, m Connector, 8, -pin,000 Hz 500 Hz Dimensions 8 x 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 9) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic Nm ) of s r 5) other output functions available on request. 6) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = mm/a Stainless steel = 0 mm 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) Order information Type Order no. I08-0BPS-ZW I08-0BPS-ZT I08-06NNS-ZW I08-06NPS-ZW I08-06NPS-ZT SENSICK CATALOGUE 5

37 Inductive sensor, I08, NAUR, Flush Inductive sensor Sensing range mm NAUR to EN High switching frequency Robust brass housing, nickelplated, with fine thread 8 x mm Enclosure rating IP 67 Classification PTB 0 ATEX 07 II G EEx ia IIC T6 Dimensional drawing Connection 0 Fastening nuts ( x); width across, metal 8x I08-0B-N-ZW0 x 0. mm² See chapter Accessories Switching units 6 SENSICK CATALOGUE

38 I08 Technical specifications I08-0B-N- ZW0 Sensing range S n mm Electrical configuration NAUR Supply voltage V s DC V Nominal voltage V n DC 8. V Power consumption, attenuated ma Power consumption, unattenuated. ma Internal capacitance 80 nf Internal inductance 0 µh Cable resistance 50 Ohm Temperature drift, of s r ± 0 % EC According to EN Switching output Control current dependent on switching state ) Output function NAUR Installation Flush Cable, PVC, m Enclosure rating IP 67 ) ax. switching frequency,000 Hz Dimensions 8 x ) Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque.5 Nm ) according to EN ) according to EN 6059 ) Thread diameter x pitch (mm) ax. data for connecting Isolating unit EN EX or other approved isolating amplifier: Short circuit current Kmax 50 ma No load voltage U O 6 V Power loss P max 75 mw Order information Type Order no. I08-0B-N-ZW SENSICK CATALOGUE 7

39 Inductive sensor, I, DC -wire, Standard series, Flush Inductive sensor Sensing range mm Short-circuit protection (pulsed) High switching frequency Dimensional drawing 0 x Robust brass housing, 50 nickel-plated with fine thread x mm Enclosure rating IP 67 x 65 x 60.5 Connection Display LED Fastening nuts ( x); width across 7, metal I-0B-ZW I-0BPS-ZT I-0BNS-ZC I-0B-ZC I-0BNS-ZW I-0BNS-ZT I-0BPS-ZC I-0BPO-ZC I-0BPO-ZW I-0BPS-ZW See chapter Accessories Connector,, -pin Connector, 8, -pin x 0. mm² 8, -pin, -pin, -pin ounting systems /NC wht NC 8 SENSICK CATALOGUE

40 I Technical specifications I- 0B -ZW 0BNS -ZW 0BPO -ZW 0BPS -ZW 0BNS -ZC 0B -ZC 0BPO -ZC 0BPS -ZC 0BPS -ZT 0BNS -ZT Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally closed Normally open Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin Connector, 8, -pin,000 Hz Dimensions x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) without load ) of s r 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I-0B-ZW I-0BNS-ZW I-0BPO-ZW I-0BPS-ZW I-0BNS-ZC I-0B-ZC I-0BPO-ZC I-0BPS-ZC I-0BPS-ZT I-0BNS-ZT SENSICK CATALOGUE 9

41 Inductive sensor, I, DC -wire, Standard series, Non-flush Inductive sensor Sensing range mm Short-circuit protection (pulsed) High switching frequency Robust brass housing, nickel-plated with fine thread Dimensional drawing x x mm Enclosure rating IP 67 8 x 65 8 x 60.5 Connection Display LED Fastening nuts ( x); width across 7, metal I-0NNS-ZW I-0NPS-ZT I-0NNS-ZC I-0NPO-ZC I-0NPS-ZW I-0NNS-ZT I-0NPS-ZC I-0NPO-ZW See chapter Accessories Connector,, -pin x 0. mm² 8, -pin, -pin, -pin Connector, 8, -pin ounting systems /NC wht NC 0 SENSICK CATALOGUE

42 I Technical specifications I- 0NNS -ZW 0NPS -ZW 0NPO -ZW 0NNS -ZC 0NPO -ZC 0NPS -ZC 0NPS -ZT 0NNS -ZT Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin Connector, 8, -pin,000 Hz Dimensions x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) without load ) of s r 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I-0NNS-ZW I-0NPS-ZW I-0NPO-ZW I-0NNS-ZC I-0NPO-ZC I-0NPS-ZC I-0NPS-ZT I-0NNS-ZT SENSICK CATALOGUE

43 Inductive sensor, I, DC -wire, Short version Sensing range / mm Dimensional drawing Inductive sensor High switching frequency Short-circuit protection (pulsed) Robust brass housing, 0 5 x nickel-plated with fine thread x mm Enclosure rating IP 67 5 x x 7 5 x 5 Connection Display LED Fastening nuts ( x); width across 7, metal I-0BNS-ZUK I-0BPS-ZUK I-0NNS-ZUK I-0NPS-ZUK I-0BPS-ZCK I-0BNS-ZCK I-0NPS-ZCK I-0NNS-ZCK See chapter Accessories Connector,, -pin ounting systems x 0.5 mm², -pin SENSICK CATALOGUE

44 I Technical specifications I- 0BNS -ZUK 0BPS -ZUK 0BPS -ZCK 0BNS -ZCK 0NNS -ZUK 0NPS -ZUK 0NPS -ZCK 0NNS -ZCK Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PUR-PVC, m Connector,, -pin,000 Hz Dimensions x 6) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 7 Nm ) without load 5) according to EN 6059 ) of s 6) r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I-0BNS-ZUK 07 8 I-0BPS-ZUK 07 6 I-0BPS-ZCK 07 8 I-0BNS-ZCK 07 0 I-0NNS-ZUK 07 9 I-0NPS-ZUK 07 7 I-0NPS-ZCK 07 9 I-0NNS-ZCK SENSICK CATALOGUE

45 Inductive sensor, I, DC -wire, Advanced series, Flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Dimensional drawing 0 x Short-circuit protection (pulsed) 50 Robust brass housing, nickel-plated with fine thread x mm Enclosure rating IP 67 x 65 Connection Display LED Fastening nuts ( x); width across 7, metal I-0BNS-ZW I-0BPO-ZW I-0BPS-ZW I-0BNS-ZC I-0BPS-ZC I-0BPO-ZC See chapter Accessories Connector,, -pin x 0. mm², -pin, -pin ounting systems /NC wht NC SENSICK CATALOGUE

46 I Technical specifications I- 0BNS -ZW 0BPO -ZW 0BPS -ZW 0BNS -ZC 0BPO -ZC 0BPS -ZC Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function NPN PNP Installation Flush 5) Enclosure rating IP 67 6) ax. switching frequency Normally open Normally closed Cable, PVC, m Connector,, -pin,000 Hz Dimensions x 7) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 8) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) 5) without load see installation notes ) 6) of s r according to EN ) Thread diameter x pitch (mm) 8) (pulsed) Order information Type Order no. I-0BNS-ZW I-0BPO-ZW I-0BPS-ZW I-0BNS-ZC I-0BPO-ZC I-0BPS-ZC SENSICK CATALOGUE 5

47 Inductive sensor, I, DC -wire, Advanced series, Non-flush Inductive sensor Sensing range 8 mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, Dimensional drawing x nickel-plated with fine thread x mm Enclosure rating IP 67 8 x 65 Connection Display LED Fastening nuts ( x); width across 7, metal I-08N-ZW I-08NNS-ZC I-08NPO-ZC I-08NNS-ZW I-08NPS-ZC I-08NPO-ZW I-08NPS-ZW See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin, -pin /NC wht NC 6 SENSICK CATALOGUE

48 I Technical specifications I- 08NN O-ZW 08NNS 08NPO 08NPS 08NNS 08NPO 08NPS -ZW -ZW -ZW -ZC -ZC -ZC Sensing range S n Electrical configuration 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally closed Normally open Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin,000 Hz Dimensions x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) 5) without load according to EN 6059 ) 6) of s r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I-08N-ZW I-08NNS-ZW I-08NPO-ZW I-08NPS-ZW I-08NNS-ZC I-08NPO-ZC I-08NPS-ZC SENSICK CATALOGUE 7

49 Inductive sensor, I, DC -wire, Advanced short series, Flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Dimensional drawing 0 x Short-circuit protection (pulsed) 0 Robust brass housing, nickel-plated with fine thread x mm Enclosure rating IP 67 5 x 5. Connection Display LED Fastening nuts ( x); width across 7, metal I-0BNS-ZWK I-0BPS-ZWK I-0BNS-ZCK I-0BPS-ZCK I-0B-ZCK I-0BPO-ZCK See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin, -pin wht NC 8 SENSICK CATALOGUE

50 I Technical specifications I- 0BNS -ZWK 0BPS -ZWK 0B -ZCK 0BNS -ZCK 0BPO -ZCK 0BPS -ZCK Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function NPN PNP Installation Flush 5) Enclosure rating IP 67 6) ax. switching frequency Normally open Normally closed Cable, PVC, m Connector,, -pin,000 Hz Dimensions x 7) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 8) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 7 Nm ) without load ) of s r 5) see installation notes 6) according to EN ) Thread diameter x pitch (mm) 8) (pulsed) Order information Type Order no. I-0BNS-ZWK I-0BPS-ZWK I-0B-ZCK I-0BNS-ZCK I-0BPO-ZCK I-0BPS-ZCK SENSICK CATALOGUE 9

51 Inductive sensor, I, DC -wire, Advanced short series, Non-flush Inductive sensor Sensing range 8 mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread x mm Enclosure rating IP 67 Dimensional drawing x x 5 5. Connection Display LED Fastening nuts ( x); width across 7, metal I-08NNS-ZWK I-08NPS-ZWK I-08NNS-ZCK I-08NPS-ZCK I-08N-ZCK I-08NPO-ZCK See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin, -pin wht NC 50 SENSICK CATALOGUE

52 I Technical specifications I- 08NNS -ZWK 08NPS -ZWK 08NNS -ZCK 08NN O-ZCK 08NPO -ZCK 08NPS -ZCK Sensing range S n Electrical configuration 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin,000 Hz Dimensions x 6) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 7 Nm ) without load ) of s r 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I-08NNS-ZWK I-08NPS-ZWK I-08NNS-ZCK I-08N-ZCK I-08NPO-ZCK I-08NPS-ZCK SENSICK CATALOGUE 5

53 Inductive sensor, I, DC -wire, Triplex series Inductive sensor Sensing range 6 / 0 mm Triple sensing range Installation quasi flush or Dimensional drawing 7 x non-flush in metal 50 High switching frequency Short-circuit protection (pulsed) Robust brass housing, chrome-plated with fine thread x mm x Enclosure rating IP x x Connection Display LED Fastening nuts ( x); width across 7, metal I-06BPO-ZW I-06BPS-ZW I-0NNS-ZW I-0NPS-ZW I-06BNS-ZC I-06BPS-ZC I-0NPS-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin /NC 5 SENSICK CATALOGUE

54 I Technical specifications I- 06BNS -ZC 06BPO -ZW 06BPS -ZW 06BPS -ZC 0NNS -ZW 0NPS -ZW 0NPS -ZC Sensing range S n Electrical configuration 6 mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Normally closed 5) Installation Quasi-flush 6) Non-flush Enclosure rating IP 67 7) ax. switching frequency Connector,, -pin Cable, PVC, m 800 Hz 00 Hz Dimensions x 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 9) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic 0 Nm ) of s r 5) other output functions available on request. 6) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = mm/a Stainless steel = mm 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) Order information Type Order no. I-06BNS-ZC I-06BPO-ZW I-06BPS-ZW I-06BPS-ZC I-0NNS-ZW I-0NPS-ZW I-0NPS-ZC SENSICK CATALOGUE 5

55 Inductive sensor, I, DC -wire, IX series Inductive sensor Sensing range 6 / 0 mm Triple sensing range Robust stainless steel VA, 6L one piece housing, with fine thread x mm Enclosure rating IP 69K + IP 68 Especially suitable for use in the food and beverage sector Visual installation support Dimensional drawing Connection 8 Display LED Ø 0.5 Ø Fastening nuts ( x); width across 7, stainless steel VA, 6L x x I-06BPO-NC I-06BNS-NC I-06BPS-NC I-0NNS-NC I-0NPS-NC See chapter Accessories Connector,, -pin ounting systems, -pin, -pin wht NC 5 SENSICK CATALOGUE

56 I Technical specifications I- 06BNS -NC 06BPO -NC 06BPS -NC 0NNS -NC 0NPS -NC Sensing range S n Electrical configuration 6 mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Installation Normally closed 5) Flush Non-flush 6) Connector,, -pin Enclosure rating IP68, IP 69K 7) ax. switching frequency 00 Hz Dimensions x 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm 0) Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load 9) Stainless steel VA.0, 6L 0 Nm ) of s r 5) other output functions available on request. 6) see installation notes 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) 0) according to IEC /7. Correction factors: Flush installation: Non-flush installation: Steel (ST7).0.0 Copper Aluminium.0.0 Brass.. Stainless steel mm / mm thick 0.5 / / 0.9 Order information Type Order no. I-06BNS-NC I-06BPO-NC I-06BPS-NC I-0NNS-NC I-0NPS-NC SENSICK CATALOGUE 55

57 Inductive sensor, I, DC -wire, for harsh environments Inductive sensor Sensing range / mm For harsh environment, resistant to most cutting oils Enclosure rating IP 68 Complementary output function Robust brass housing, Dimensional drawing nickel-plated with fine thread x mm LED status indicator ( function) Connection Display LED Fastening nuts ( x); width across 7, metal I-0BNP-ZC I-0BPP-ZC I-0NNP-ZC I-0NPP-ZC See chapter Accessories Connector,, -pin ounting systems, -pin wht NC 56 SENSICK CATALOGUE

58 I Technical specifications I- 0BNP -ZC 0BPP -ZC 0NNP -ZC 0NPP -ZC Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Complementary Flush Non-flush Enclosure rating IP 68 ax. switching frequency Connector,, -pin,000 Hz Dimensions x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) without load 5) Thread diameter x pitch (mm) ) of s 6) r (pulsed) Order information Type Order no. I-0BNP-ZC I-0BPP-ZC I-0NNP-ZC I-0NPP-ZC SENSICK CATALOGUE 57

59 Inductive sensor, I, DC -wire, ultitalents Inductive sensor Sensing range / mm Free configurable output functions in one sensor PNP /, PNP / NC NPN /, NPN / NC Short-circuit protection Robust brass housing, nickel-plated with fine thread x mm Enclosure rating IP 67 LED status indicator ( function) Dimensional drawing x x x 5 x 75 Connection Display LED Fastening nuts ( x); width across 7, metal I-0BCP-ZW I-0NCP-ZW I-0BCP-ZC I-0NCP-ZC x 0. mm² PNP version NPN version, -pin PNP version NPN version See chapter Accessories Connector,, -pin ounting systems wht wht NC wht wht wht NC wht wht NC wht NC 58 SENSICK CATALOGUE

60 I Technical specifications I- 0BCP -ZW 0BCP -ZC 0NCP -ZW 0NCP -ZC Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 50 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP/NPN config. Configurable Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin,000 Hz Dimensions x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 0 Nm ) 5) without load according to EN 6059 ) 6) of s r Thread diameter x pitch (mm) Order information Type Order no. I-0BCP-ZW I-0BCP-ZC I-0NCP-ZW I-0NCP-ZC SENSICK CATALOGUE 59

61 Inductive sensor, I, DC -wire Inductive sensor Sensing range / mm Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread x mm Dimensional drawing x Enclosure rating IP 67 High switching frequency 50 x 60 8 x x 75 Connection Display LED Fastening nuts ( x); width across 7, metal I-0BDS-ZW I-0BDO-ZW I-0NDO-ZW I-0NDS-ZW I-0BDS-ZC I-0NDS-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin 60 SENSICK CATALOGUE

62 I Technical specifications I- 0BDS -ZC 0NDS -ZC 0BDS -ZW 0BDO -ZW 0ND O-ZW 0NDS -ZW Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d.8 V ) in. load current Residual current 00 ma ma 0.8 ma Time delay before availability t v 50 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Installation Normally open Normally closed Flush Non-flush Enclosure rating IP 67 ) ax. switching frequency Connector,, -pin Cable, PVC, m,500 Hz Dimensions x ) Short-circuit protection Reverse polarity protection Shock/vibration stress 5) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque Brass nickel-plated, plastic 0 Nm ) at I a max ) of s r ) according to EN 6059 ) Thread diameter x pitch (mm) 5) (pulsed) Order information Type Order no. I-0BDS-ZC 6 00 I-0NDS-ZC I-0BDS-ZW I-0BDO-ZW 6 00 I-0NDO-ZW I-0NDS-ZW SENSICK CATALOGUE 6

63 Inductive sensor, I, AC -wire Inductive sensor Sensing range / mm Broad supply voltage range in AC Robust brass housing, Dimensional drawing Ø x nickel-plated, with fine thread 7 x mm Enclosure rating IP 67 Ø x 7 50 Connection Display LED Fastening nuts ( x); width across 7, metal I-0BAO-ZU0 I-0BAS-ZU0 I-0NAO-ZU0 I-0NAS-ZU0 See chapter Accessories ounting systems x 0.5 mm² L N 6 SENSICK CATALOGUE

64 I Technical specifications I- 0BAO -ZU0 0BAS -ZU0 0NAO -ZU0 0NAS -ZU0 Sensing range S n mm mm Electrical configuration AC -wire Supply voltage V s AC V Voltage drop U d 8.5 V ) 50 ma ( C) 00 ma ( C) Intermittent current I k 0.9 A (0 ms/0.5hz) in. load current 8 ma Residual current ma (50 V AC) Residual current.5 ma (0 V AC) Time delay before availability t v 0 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally closed Normally open Installation Flush Non-flush Cable, PUR-PVC, m Enclosure rating IP 67 ) VDE protection class ax. switching frequency 5 Hz Dimensions x ) Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 7 Nm ) at I a max ) of s r ) according to EN 6059 ) Thread diameter x pitch (mm) Order information Type Order no. I-0BAO-ZU I-0BAS-ZU I-0NAO-ZU I-0NAS-ZU SENSICK CATALOGUE 6

65 Inductive sensor, I, NAUR Inductive sensor Sensing range / NAUR to EN Robust brass housing, nickel-plated, with fine thread x mm Classification PTB 0 ATEX 07 II G EEx ia IIC T6 Dimensional drawing x x Connection Fastening nuts ( x); width across 7, metal I-0B-N-ZW0 I-0N-N-ZW0 See chapter Accessories ounting systems Switching units x 0. mm² 6 SENSICK CATALOGUE

66 I Technical specifications I- 0B- N-ZW0 0N- N-ZW0 Sensing range S n mm mm Electrical configuration NAUR Supply voltage V s DC V Nominal voltage V n DC 8. V Power consumption, attenuated ma Power consumption, unattenuated. ma Internal capacitance 0 nf Internal inductance 80 µh Cable resistance 50 Ohm Temperature drift, of s r ± 0 % EC According to EN Switching output Control current dependent on switching state ) Output function NAUR Installation Flush Non-flush Cable, PVC, m Enclosure rating IP 67 ) ax. switching frequency,00 Hz,500 Hz Dimensions x ) Short-circuit protected Reverse polarity protected Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 7 Nm ) according to NAUR EN ) according to EN 6059 ) Thread diameter x pitch (mm) ax. data for connecting Isolating unit EN EX or other approved isolating amplifier: Short circuit current Kmax 50 ma No load voltage U O 6 V Power loss P max 75 mw Order information Type Order no. I-0B-N-ZW0 6 0 I-0N-N-ZW SENSICK CATALOGUE 65

67 Inductive sensor, I8, DC -wire, Standard series, Flush Inductive sensor Sensing range 5 mm Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread 8 x mm Enclosure rating IP 67 High switching frequency Dimensional drawing x 8x 8 6 Connection Display LED Fastening nuts ( x); width across, metal I8-05BNS-ZW I8-05BPO-ZW I8-05BPS-ZW I8-05BNS-ZC I8-05BPS-ZC I8-05BPO-ZC See chapter Accessories Connector,, -pin x 0. mm², -pin, -pin ounting systems /NC wht NC 66 SENSICK CATALOGUE

68 I8 Technical specifications I8-05BNS -ZW 05BPO -ZW 05BPS -ZW 05BNS -ZC 05BPO -ZC 05BPS -ZC Sensing range S n Electrical configuration 5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector,, -pin 600 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic 0 Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I8-05BNS-ZW I8-05BPO-ZW I8-05BPS-ZW I8-05BNS-ZC I8-05BPO-ZC I8-05BPS-ZC SENSICK CATALOGUE 67

69 Inductive sensor, I8, DC -wire, Standard series, Non-flush Inductive sensor Sensing range 8 mm Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread 8 x mm Dimensional drawing x Enclosure rating IP 67 High switching frequency 8x Connection Display LED Fastening nuts ( x); width across, metal I8-08N-ZW I8-08NNS-ZC I8-08NPO-ZC I8-08NNS-ZW I8-08NPS-ZC I8-08NPS-ZW I8-08NNS-ZWA See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin, -pin /NC wht NC 68 SENSICK CATALOGUE

70 I8 Technical specifications I8-08NN O-ZW 08NNS 08NPS 08NNS 08NNS 08NPO 08NPS -ZW -ZW -ZWA -ZC -ZC -ZC Sensing range S n Electrical configuration 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally closed Normally open Non-flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Cable, PVC, m Connector,, -pin 600 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic 0 Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I8-08N-ZW I8-08NNS-ZW I8-08NPS-ZW I8-08NNS-ZWA 6 00 I8-08NNS-ZC I8-08NPO-ZC I8-08NPS-ZC SENSICK CATALOGUE 69

71 Inductive sensor, I8, DC -wire, Short version Sensing range 5 / 8 mm Dimensional drawing Inductive sensor Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread 8 x mm 0 0 8x Enclosure rating IP 67 High switching frequency 8x 0 8x 0 5 8x 5 Connection Display LED Fastening nuts ( x); width across, metal I8-05BNS-ZUK I8-05BPS-ZUK I8-08NNS-ZUK I8-08NPS-ZUK I8-05BNS-ZCK I8-05BPS-ZCK I8-08NNS-ZCK I8-08NPS-ZCK See chapter Accessories Connector,, -pin ounting systems x 0.5 mm², -pin 70 SENSICK CATALOGUE

72 I8 Technical specifications I8-05BNS -ZUK 05BPS -ZUK 05BNS -ZCK 05BPS -ZCK 08NNS -ZUK 08NPS -ZUK 08NNS -ZCK 08NPS -ZCK Sensing range S n Electrical configuration 5 mm 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Flush Non-flush Enclosure rating IP 67 ) ax. switching frequency Cable, PUR-PVC, m Connector,, -pin,000 Hz Dimensions 8 x 5) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic 5 Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I8-05BNS-ZUK 07 I8-05BPS-ZUK 07 0 I8-05BNS-ZCK 07 I8-05BPS-ZCK 07 I8-08NNS-ZUK 07 I8-08NPS-ZUK 07 I8-08NNS-ZCK 07 5 I8-08NPS-ZCK SENSICK CATALOGUE 7

73 Inductive sensor, I8, DC -wire, Advanced series, Flush Inductive sensor Sensing range 8 mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread 8 x mm Enclosure rating IP 67 Dimensional drawing x 8x 8 6 Connection Display LED Fastening nuts ( x); width across, metal I8-08BNS-ZW I8-08BPS-ZWB I8-08BPS-ZW I8-08BNS-ZC I8-08BPS-ZC I8-08BPO-ZC See chapter Accessories Connector,, -pin x 0. mm², -pin, -pin ounting systems wht NC 7 SENSICK CATALOGUE

74 I8 Technical specifications I8-08BNS -ZC 08BNS -ZW 08BPO -ZC 08BPS -ZC 08BPS -ZWB 08BPS -ZW Sensing range S n Electrical configuration 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function NPN PNP Installation Flush ) Enclosure rating IP 67 5) ax. switching frequency Normally open Normally closed Connector,, -pin Cable, PVC, m Cable, PVC, 5 m 00 Hz Dimensions 8 x 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic 0 Nm ) of s r ) see installation notes 5) according to EN ) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I8-08BNS-ZC I8-08BNS-ZW I8-08BPO-ZC I8-08BPS-ZC I8-08BPS-ZWB I8-08BPS-ZW SENSICK CATALOGUE 7

75 Inductive sensor, I8, DC -wire, Advanced series, Non-flush Inductive sensor Sensing range mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Robust brass housing, Dimensional drawing x nickel-plated with fine thread 8 x mm Enclosure rating IP 67 8x Connection Display LED Fastening nuts ( x); width across, metal I8-NNS-ZW I8-NPS-ZW I8-NNS-ZC I8-NPS-ZC I8-NPO-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin, -pin wht NC 7 SENSICK CATALOGUE

76 I8 Technical specifications I8- NNS -ZC NNS -ZW NPO -ZC NPS -ZC NPS -ZW Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Non-flush Enclosure rating IP 67 ) ax. switching frequency Connector,, -pin Cable, PVC, m 00 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) at I a max ) without load Brass nickel-plated, plastic 0 Nm ) of s r ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I8-NNS-ZC I8-NNS-ZW I8-NPO-ZC I8-NPS-ZC I8-NPS-ZW SENSICK CATALOGUE 75

77 Inductive sensor, I8, DC -wire, Triplex series Inductive sensor Sensing range / 0 mm Triple sensing range Installation quasi flush or non-flush in metal Short-circuit protection (pulsed) Dimensional drawing 50 8x Robust brass housing, chrome-plated with fine thread 8 x mm Enclosure rating IP x 6.5 8x x Connection Display LED Fastening nuts ( x); width across, metal I8-BNS-ZW I8-BPS-ZW I8-0NPS-ZW I8-BPS-ZC I8-0NPS-ZC See chapter Accessories Connector,, -pin x 0. mm², -pin ounting systems 76 SENSICK CATALOGUE

78 I8 Technical specifications I8- BNS -ZW BPS -ZW BPS -ZC 0NPS -ZW 0NPS -ZC Sensing range S n Electrical configuration mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Installation Quasi-flush 6) Non-flush Enclosure rating IP 67 7) ax. switching frequency Cable, PVC, m Connector,, -pin 500 Hz 00 Hz Dimensions 8 x 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 9) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic 0 Nm ) of s r 5) other output functions available on request. 6) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = mm/a Stainless steel =.5 mm 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) Order information Type Order no. I8-BNS-ZW I8-BPS-ZW I8-BPS-ZC I8-0NPS-ZW I8-0NPS-ZC SENSICK CATALOGUE 77

79 Inductive sensor, I8, DC -wire, Triplex series, short version Inductive sensor Sensing range mm Triple sensing range Installation quasi flush in metal Short-circuit protection (pulsed) Robust brass housing, chrome-plated with fine thread 8 x mm Enclosure rating IP 67 Dimensional drawing &! Connection Display LED Fastening nuts ( x); width across, metal 8x I8-BPS-ZCK, -pin See chapter Accessories Connector,, -pin ounting systems 78 SENSICK CATALOGUE

80 I8 Technical specifications I8- BPS -ZCK Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function PNP Normally open Installation Quasi-flush 5) Enclosure rating IP 67 6) ax. switching frequency Connector,, -pin 500 Hz Dimensions 8 x 7) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 8) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic 0 Nm ) of s r 5) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = mm/a Stainless steel =.5 mm 6) according to EN ) Thread diameter x pitch (mm) 8) (pulsed) Order information Type Order no. I8-BPS-ZCK SENSICK CATALOGUE 79

81 Inductive sensor, I8, DC -wire, IX series Inductive sensor Sensing range 0 / 0 mm Triple sensing range Robust stainless steel VA, 6L one piece housing, with fine thread 8 x mm Enclosure rating IP 69K + IP 68 Especially suitable for use in the food and beverage sector Visual installation support Dimensional drawing x 8x 6.5 Connection Display LED Fastening nuts (x); width across, stainless steel VA, 6L I8-0BPO-NC I8-0BNS-NC I8-0BPS-NC I8-0NNS-NC I8-0NPS-NC See chapter Accessories Connector,, -pin, -pin, -pin wht NC 80 SENSICK CATALOGUE

82 I8 Technical specifications I8-0BNS -NC 0BPO -NC 0BPS -NC 0NNS -NC 0NPS -NC Sensing range S n Electrical configuration 0 mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Installation Normally closed 5) Flush Non-flush 6) Connector,, -pin Enclosure rating IP68, IP 69K 7) ax. switching frequency 00 Hz Dimensions 8 x 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm 0) Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load 9) Stainless steel VA.0, 6L 50 Nm ) of s r 5) other output functions available on request. 6) see installation notes 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) 0) according to IEC /7. Correction factors: Flush installation: Non-flush installation: Steel (ST7).0.0 Copper Aluminium.0.0 Brass.. Stainless steel mm / mm thick 0. / / 0.8 Order information Type Order no. I8-0BNS-NC I8-0BPO-NC I8-0BPS-NC I8-0NNS-NC I8-0NPS-NC SENSICK CATALOGUE 8

83 Inductive sensor, I8, DC -wire, for harsh environments Inductive sensor Sensing range 5/ 8 mm For harsh environment, resistant to most cutting oils Enclosure rating IP 68 Complementary output function Robust brass housing, Dimensional drawing x nickel-plated with fine thread 8 x mm 8x LED status indicator ( function) 5 6 Connection Display LED Fastening nuts ( x); width across, metal I8-05BNP-ZC I8-05BPP-ZC I8-08NNP-ZC I8-08NPP-ZC See chapter Accessories Connector,, -pin ounting systems, -pin wht NC 8 SENSICK CATALOGUE

84 I8 Technical specifications I8-05BNP -ZC 05BPP -ZC 08NNP -ZC 08NPP -ZC Sensing range S n Electrical configuration 5 mm 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d 0.8 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Complementary Flush Non-flush Enclosure rating IP 68 ax. switching frequency Connector,, -pin,000 Hz Dimensions 8 x ) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 5) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque Brass nickel-plated, plastic 0 Nm ) at I a max ) without load ) of s r ) Thread diameter x pitch (mm) 5) (pulsed) Order information Type Order no. I8-05BNP-ZC I8-05BPP-ZC I8-08NNP-ZC I8-08NPP-ZC SENSICK CATALOGUE 8

85 Inductive sensor, I8, DC -wire, ultitalents Inductive sensor Sensing range 5 / 8 mm Free configurable output functions in one sensor PNP /, PNP / NC NPN /, NPN / NC Short-circuit protection Robust brass housing, nickel-plated with fine thread 8 x mm Enclosure rating IP 67 Dimensional drawing x 8x LED status indicator ( function) 60 8x x 7 Connection Display LED Fastening nuts ( x); width across, metal I8-05BCP-ZW I8-05BCP-ZC I8-08NCP-ZW I8-08NCP-ZC x 0. mm², -pin PNP version NPN version PNP version NPN version See chapter Accessories Connector,, -pin ounting systems wht wht wht wht wht NC wht NC wht NC wht NC 8 SENSICK CATALOGUE

86 I8 Technical specifications I8-05BCP -ZW 05BCP -ZC 08NCP -ZW 08NCP -ZC Sensing range S n Electrical configuration 5 mm 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP/NPN config. Configurable Flush Non-flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector,, -pin 00 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque Brass nickel-plated, plastic 0 Nm ) at I a max ) without load ) of s r ) according to EN ) Thread diameter x pitch (mm) Order information Type Order no. I8-05BCP-ZW I8-05BCP-ZC I8-08NCP-ZW I8-08NCP-ZC SENSICK CATALOGUE 85

87 Inductive sensor, I8, DC -wire Inductive sensor Sensing range 5 / 8 mm Short-circuit protection (pulsed) Robust brass housing, nickel-plated with fine thread 8 x mm Dimensional drawing x Enclosure rating IP 67 8x x x 8 6 Connection Display LED Fastening nuts ( x); width across, metal I8-05BDS-ZW I8-08NDS-ZW I8-05BDS-ZC I8-08NDS-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin 86 SENSICK CATALOGUE

88 I8 Technical specifications I8-05BDS -ZW 05BDS -ZC 08NDS -ZW 08NDS -ZC Sensing range S n Electrical configuration 5 mm 8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d.8 V ) in. load current Residual current 00 ma ma 0.8 ma Time delay before availability t v 50 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally open ) Installation Flush Non-flush Enclosure rating IP 67 ) ax. switching frequency Cable, PVC, m Connector,, -pin 00 Hz Dimensions 8 x 5) Short-circuit protection Reverse polarity protection Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque Brass nickel-plated, plastic 0 Nm ) at I a max ) of s r ) normally closed function available on request ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I8-05BDS-ZW I8-05BDS-ZC I8-08NDS-ZW 6 00 I8-08NDS-ZC SENSICK CATALOGUE 87

89 Inductive sensor, I8, AC/DC -wire Sensing range 5 / 8 mm Dimensional drawing Inductive sensor Broad supply voltage range in AC and DC Robust brass housing, nickel-plated, with fine thread x 8 x mm Enclosure rating IP 67 8x Connection Display LED Fastening nuts ( x); width across, metal I8-05BUO-ZU0 I8-08NUO-ZU0 I8-05BUS-ZU0 I8-08NUS-ZU0 See chapter Accessories ounting systems x 0.5 mm² L (/NC) x 0.5 mm² L (/) N () N () 88 SENSICK CATALOGUE

90 I8 Technical specifications I8-05BUO -ZU0 05BUS -ZU0 08NUO -ZU0 08NUS -ZU0 Sensing range S n 5 mm 8 mm Electrical configuration AC/DC -wire Supply voltage V s AC/DC V Voltage drop U d AC/DC 6.5 V / 6 V 50 ma AC ( C) 50 ma AC ( C) 00 ma DC Intermittent current I k. A (0 ms/0.5hz) in. load current 5 ma Residual current.5 ma (50 V AC) Residual current. ma (0 V AC) Residual current 0.8 ma ( V DC) Time delay before availability t v 8 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally closed Normally open Installation Flush Non-flush Cable, PUR-PVC, m Cable, PVC/PUR, m Enclosure rating IP 67 ) VDE protection class ax. switching frequency AC/DC 5 Hz / 00 Hz Dimensions 8 x ) Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 5 Nm ) of s r ) according to EN 6059 ) Thread diameter x pitch (mm) Order information Type Order no. I8-05BUO-ZU I8-05BUS-ZU I8-08NUO-ZU I8-08NUS-ZU SENSICK CATALOGUE 89

91 Inductive sensor, I8, NAUR Sensing range 5 / 8 mm Dimensional drawing Inductive sensor NAUR to EN High switching frequency Robust brass housing, nickel-plated, with fine thread 8 x mm Enclosure rating IP 67 Classification PTB 0 ATEX x 8x II G EEx ia IIC T6 Connection Fastening nuts ( x); width across, metal I8-05B-N-ZW0 I8-08N-N-ZWO See chapter Accessories ounting systems Switching units x 0. mm² 90 SENSICK CATALOGUE

92 I8 Technical specifications I8-05B- N-ZW0 08N- N-ZWO Sensing range S n 5 mm 8 mm Electrical configuration NAUR Supply voltage V s DC V Nominal voltage V n DC 8. V Power consumption, attenuated ma Power consumption, unattenuated. ma Internal capacitance 0 nf 0 nf Internal inductance 60 µh Cable resistance 50 Ohm Temperature drift, of s r ± 0 % EC According to EN Switching output Control current dependent on switching state ) Output function NAUR Installation Flush Non-flush Cable, PVC, m Enclosure rating IP 67 ) ax. switching frequency 70 Hz 00 Hz Dimensions 8 x ) short-circuit protected Reverse polarity protected Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 5 Nm ) according to NAUR EN ) according to EN 6059 ) Thread diameter x pitch (mm) ax. data for connecting Isolating unit EN EX or other approved isolating amplifier: Short circuit current Kmax 50 ma No load voltage U O 6 V Power loss P max 75 mw Order information Type Order no. I8-05B-N-ZW I8-08N-N-ZWO SENSICK CATALOGUE 9

93 Inductive sensor, I0, DC -wire, Standard series Inductive sensor Sensing range 0 / 5 mm Dimensional drawing High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel-plating with fine thread x.5 0 x.5 mm Enclosure rating IP 67 0x x x.5 6 Connection Display LED Fastening nuts ( x); width across 6, metal I0-0BNS-ZW I0-0BNS-ZC I0-0BPO-ZC I0-0BPS-ZW I0-0BPS-ZC I0-5NNS-ZW I0-5NNS-ZC I0-5NPS-ZW I0-5NPS-ZC I0-5NPO-ZW See chapter Accessories Connector,, -pin ounting systems x 0.5 mm², -pin, -pin /NC wht NC 9 SENSICK CATALOGUE

94 I0 Technical specifications I0-0BNS -ZW 0BPS -ZW 0BNS -ZC 0BPO -ZC 0BPS -ZC 5NNS -ZW 5NPS -ZW 5NPO -ZW 5NNS -ZC 5NPS -ZC Sensing range S n Electrical configuration 0 mm 5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Normally closed Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector,, -pin 00 Hz Dimensions 0 x.5 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 60 Nm ) without load 5) according to EN 6059 ) of s 6) r Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I0-0BNS-ZW I0-0BPS-ZW I0-0BNS-ZC I0-0BPO-ZC I0-0BPS-ZC I0-5NNS-ZW I0-5NPS-ZW I0-5NPO-ZW I0-5NNS-ZC I0-5NPS-ZC SENSICK CATALOGUE 9

95 Inductive sensor, I0, DC -wire, Short version Sensing range 0 / 5 mm Dimensional drawing Inductive sensor Short-circuit protection (pulsed) Robust brass housing, nickel-plating with fine thread 0 x.5 mm Enclosure rating IP 67 High switching frequency x.5 0x.5 0x x.5 Connection Display LED 7 50 Fastening nuts ( x); width across 6, metal I0-0BNS-ZUK I0-0BPS-ZUK I0-5NPS-ZUK I0-5NNS-ZUK I0-0BNS-ZCK I0-0BPS-ZCK I0-5NNS-ZCK I0-5NPS-ZCK See chapter Accessories Connector,, -pin ounting systems x 0.5 mm², -pin 9 SENSICK CATALOGUE

96 I0 Technical specifications I0-0BNS -ZUK 0BPS -ZUK 0BNS -ZCK 0BPS -ZCK 5NPS -ZUK 5NNS -ZUK 5NNS -ZCK 5NPS -ZCK Sensing range S n Electrical configuration 0 mm 5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 5 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation ax. switching frequency NPN PNP Normally open Flush Non-flush Cable, PUR-PVC, m Connector,, -pin 500 Hz Dimensions 0 x.5 5) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 50 Nm ) without load ) of s r 5) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I0-0BNS-ZUK 07 6 I0-0BPS-ZUK 07 I0-0BNS-ZCK 07 8 I0-0BPS-ZCK 07 6 I0-5NPS-ZUK 07 5 I0-5NNS-ZUK 07 7 I0-5NNS-ZCK 07 9 I0-5NPS-ZCK SENSICK CATALOGUE 95

97 Inductive sensor, I0, DC -wire, Advanced series, Flush Inductive sensor Sensing range 5 mm Dimensional drawing Enhanced sensing range High switching frequency Short-circuit protection (pulsed) 0x.5 Robust brass housing, nickel-plated with fine thread 0 x.5 mm Enclosure rating IP 67 0x.5 6 Connection Display LED Fastening nuts ( x); width across 6, metal I0-5BNS-ZW I0-5BPO-ZW I0-5BPS-ZW I0-5BNS-ZC I0-5BPS-ZC I0-5BPO-ZC See chapter Accessories Connector,, -pin x 0.5 mm², -pin, -pin ounting systems /NC wht NC 96 SENSICK CATALOGUE

98 I0 Technical specifications I0-5BNS -ZW 5BPO -ZW 5BPS -ZW 5BNS -ZC 5BPO -ZC 5BPS -ZC Sensing range S n Electrical configuration 5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function NPN PNP Installation Flush 5) ax. switching frequency Normally open Normally closed Cable, PVC, m Connector,, -pin 50 Hz Dimensions 0 x.5 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 60 Nm ) without load ) of s r 5) see installation notes 6) Thread diameter x pitch (mm) 7) (pulsed) Order information Type Order no. I0-5BNS-ZW I0-5BPO-ZW I0-5BPS-ZW I0-5BNS-ZC I0-5BPO-ZC I0-5BPS-ZC SENSICK CATALOGUE 97

99 Inductive sensor, I0, DC -wire, Advanced series, Non-flush Inductive sensor Sensing range 0 mm Dimensional drawing Enhanced sensing range High switching frequency Short-circuit protection (pulsed) 0x.5 Robust brass housing, nickel-plated with fine thread 0 x.5 mm 8 60 Enclosure rating IP 67 0x Connection Display LED Fastening nuts ( x); width across 6, metal I0-0NNS-ZW I0-0NPO-ZW I0-0NPS-ZW I0-0NNS-ZC I0-0NPS-ZC See chapter Accessories Connector,, -pin x 0.5 mm², -pin ounting systems /NC 98 SENSICK CATALOGUE

100 I0 Technical specifications I0-0NNS -ZW 0NPO -ZW 0NPS -ZW 0NNS -ZC 0NPS -ZC Sensing range S n Electrical configuration 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation ax. switching frequency NPN PNP Normally open Normally closed Non-flush Cable, PVC, m Connector,, -pin 50 Hz Dimensions 0 x.5 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max Brass nickel-plated, plastic 60 Nm ) without load ) of s r 5) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I0-0NNS-ZW I0-0NPO-ZW I0-0NPS-ZW I0-0NNS-ZC I0-0NPS-ZC SENSICK CATALOGUE 99

101 Inductive sensor, I0, DC -wire, Triplex series Inductive sensor Sensing range / 0 mm Dimensional drawing Triple sensing range Installation quasi flush or non-flush in metal 0x.5 Short-circuit protection (pulsed) Robust brass housing, 5 60 chrome-plated with fine thread 0 x mm Enclosure rating IP x x Connection Display LED Fastening nuts ( x); width across 6, metal I0-BNS-ZW I0-BPS-ZC I0-0NPS-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin 00 SENSICK CATALOGUE

102 I0 Technical specifications I0- BNS -ZW BPS -ZC 0NPS -ZC Sensing range S n Electrical configuration mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Installation Quasi-flush 6) ax. switching frequency Non-flush Cable, PVC, m Connector,, -pin 00 Hz 00 Hz Dimensions 0 x.5 7) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 8) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic 60 Nm ) of s r 5) other output functions available on request. 6) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = 6 mm/a Stainless steel = mm 7) Thread diameter x pitch (mm) 8) (pulsed) Order information Type Order no. I0-BNS-ZW I0-BPS-ZC I0-0NPS-ZC SENSICK CATALOGUE 0

103 Inductive sensor, I0, DC -wire, Triplex series, short version Inductive sensor Sensing range mm Triple sensing range Installation quasi flush in metal Short-circuit protection (pulsed) Robust brass housing, chrome-plated with fine thread 0 x mm Enclosure rating IP 67 Dimensional drawing Connection Display LED Fastening nuts ( x); width across 6, metal 0x.5 I0-BPS-ZCK I0-BPO-ZCK, -pin, -pin See chapter Accessories Connector,, -pin ounting systems wht NC 0 SENSICK CATALOGUE

104 I0 Technical specifications I0- BPO -ZCK BPS -ZCK Sensing range S n Electrical configuration mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output PNP Output function Normally closed 5) Normally open 5) Installation Quasi-flush 6) Enclosure rating IP 67 7) ax. switching frequency Connector,, -pin 00 Hz Dimensions 0 x.5 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 9) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load Brass, chrome-plated, plastic 60 Nm ) of s r 5) other output functions available on request. 6) when mounting in conductible materials the sensors must be installed with a distance A to the surface. A Steel, metal = 6 mm/a Stainless steel = mm 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) Order information Type Order no. I0-BPO-ZCK I0-BPS-ZCK SENSICK CATALOGUE 0

105 Inductive sensor, I0, DC -wire, IX series Inductive sensor Sensing range 0 / 0 mm Triple sensing range Robust stainless steel VA, 6L one piece housing, with fine thread 0 x.5 mm Enclosure rating IP 69K + IP 68 Especially suitable for use in the food and beverage sector Visual installation support Dimensional drawing x.5 0x Connection Display LED Fastening nuts ( x); width across 6, stainless steel VA, 6L I0-0BNS-NC I0-0BPS-NC I0-0NNS-NC I0-0NPS-NC See chapter Accessories Connector,, -pin, -pin 0 SENSICK CATALOGUE

106 I0 Technical specifications I0-0BNS -NC 0BPS -NC 0NNS -NC 0NPS -NC Sensing range S n Electrical configuration 0 mm 0 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r 0 % EC According to EN Switching output NPN PNP Output function Normally open 5) Installation Flush Non-flush 6) Connector,, -pin Enclosure rating IP68, IP 69K 7) ax. switching frequency 00 Hz Dimensions 0 x.5 8) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm 0) Ambient temperature T a -5 C C Housing material Tightening torque ) of U b ) at I a max ) without load 9) Stainless steel VA.0, 6L 50 Nm ) of s r 5) other output functions available on request. 6) see installation notes 7) according to EN ) Thread diameter x pitch (mm) 9) (pulsed) 0) according to IEC /7. Correction factors: Flush installation: Non-flush installation: Steel (ST7).0.0 Copper Aluminium.0.0 Brass.. Stainless steel mm / mm thick 0.5 / / 0.5 Order information Type Order no. I0-0BNS-NC I0-0BPS-NC I0-0NNS-NC I0-0NPS-NC SENSICK CATALOGUE 05

107 Inductive sensor, I0, DC -wire Inductive sensor Sensing range 0 / 5 mm Short-circuit protection (pulsed) Robust brass housing, Dimensional drawing 0x.5 nickel-plated with fine thread 0 x mm 8 60 Enclosure rating IP 67 0x x x Connection Display LED Fastening nuts ( x); width across 6, metal I0-0BDS-ZW I0-5NDS-ZW I0-0BDS-ZC I0-5NDS-ZC See chapter Accessories Connector,, -pin ounting systems x 0. mm², -pin 06 SENSICK CATALOGUE

108 I0 Technical specifications I0-0BDS -ZW 0BDS -ZC 5NDS -ZW 5NDS -ZC Sensing range S n Electrical configuration 0 mm 5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % Voltage drop U d.8 V ) in. load current Residual current 00 ma ma 0.8 ma Time delay before availability t v 50 ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally open ) Installation Flush Non-flush Cable, PVC, m Connector,, -pin Enclosure rating IP 67 ) ax. switching frequency 50 Hz Dimensions 0 x.5 5) Short-circuit protection Reverse polarity protection Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Tightening torque Brass nickel-plated, plastic 60 Nm ) at I a max ) of s r ) normally closed function available on request ) according to EN ) Thread diameter x pitch (mm) 6) (pulsed) Order information Type Order no. I0-0BDS-ZW I0-0BDS-ZC I0-5NDS-ZW I0-5NDS-ZC SENSICK CATALOGUE 07

109 Inductive sensor, I0, AC/DC -wire Inductive sensor Sensing range 0 / 5 mm Dimensional drawing Broad supply voltage range in AC and DC Robust brass housing, 0x.5 nickel-plated, with fine thread 0 x.5 mm Enclosure rating IP x.5 8 Connection Display LED Fastening nuts ( x); width across 6, metal 8 59 I0-0BUO-ZU0 I0-0BUS-ZU0 I0-5NUO-ZU0 I0-5NUS-ZU0 See chapter Accessories ounting systems x 0.5 mm² 08 SENSICK CATALOGUE

110 I0 Technical specifications I0-0BUO -ZU0 0BUS -ZU0 5NUO -ZU0 5NUS -ZU0 Sensing range S n 0 mm 5 mm Electrical configuration AC/DC -wire Supply voltage V s AC/DC V Voltage drop U d AC/DC 6.5 V / 6 V 50 ma ( C) 50 ma ( C) 00 ma DC Intermittent current I k. A (0 ms/0.5hz) in. load current 5 ma Residual current.5 ma (50 V AC) Residual current. ma (0 V AC) Residual current 0.8 ma ( V DC) Time delay before availability t v 8 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally closed Normally open Installation Flush Non-flush Cable, PUR-PVC, m Enclosure rating IP 67 ) VDE protection class ax. switching frequency AC/DC 5 Hz / 0 Hz Dimensions 0 x.5 ) Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 50 Nm ) of s r ) according to EN ) thread diameter x pitch (mm) Order information Type Order no. I0-0BUO-ZU I0-0BUS-ZU I0-5NUO-ZU I0-5NUS-ZU SENSICK CATALOGUE 09

111 Inductive sensor, I0, NAUR Inductive sensor Sensing range 0 / 5 mm Dimensional drawing NAUR to EN High switching frequency Robust brass housing, nickel-plated, with fine thread 0 x.5 mm Classification PTB 0 ATEX 07 II G EEx ia IIC T6 5 0x.5 0x.5 Connection Fastening nuts ( x); width across 6, metal I0-0B-N-ZW0 I0-5N-N-ZW0 See chapter Accessories ounting systems Switching units x 0.5 mm² 0 SENSICK CATALOGUE

112 I0 Technical specifications I0-0B- N-ZW0 N-ZW0 Sensing range S n 0 mm 5 mm Electrical configuration NAUR Supply voltage V s DC V Nominal voltage V n DC 8. V Power consumption, attenuated ma Power consumption, unattenuated. ma Internal capacitance 0 nf 0 nf Internal inductance 0 µh 00 µh Cable resistance 50 Ohm Temperature drift, of s r ± 0 % EC According to EN Switching output Control current dependent on switching state ) Output function NAUR Installation Flush Non-flush Cable, PVC, m Enclosure rating IP 67 ) ax. switching frequency 50 Hz 00 Hz Dimensions 0 x.5 ) short-circuit protected Reverse polarity protected Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Brass nickel-plated, plastic Tightening torque 50 Nm ) according to NAUR EN ) according to EN ) thread diameter x pitch (mm) ax. data for connecting Isolating unit EN EX or other approved isolating amplifier: Short circuit current Kmax 50 ma No load voltage U O 6 V Power loss P max 75 mw Order information Type Order no. I0-0B-N-ZW I0-5N-N-ZW SENSICK CATALOGUE

113 Inductive sensor, IH0, DC -wire, iniature series, Flush Inductive sensor Sensing range 0.6 mm Can be installed flush High switching frequency Short-circuit protection (pulsed) Solid stainless steel housing Enclosure rating IP 67 Dimensional drawing 6 Connection Display LED Ø IH0-0B6NS-VU IH0-0B6PS-VU x 0.06 mm² SENSICK CATALOGUE

114 IH0 Technical specifications IH0-0B6NS -VU 0B6PS -VU Sensing range S n Electrical configuration 0.6 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d 0.6 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 % % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Sleeve diameter Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Cable, PUR, m 5,000 Hz mm 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a = 50 ma Stainless steel, plastic ) without load ) normally closed function available on request 5) according to EN ) (pulsed) Order information Type Order no. IH0-0B6NS-VU 6 00 IH0-0B6PS-VU SENSICK CATALOGUE

115 Inductive sensor, IH0, DC -wire, iniature series, Flush Sensing range 0.8 mm Dimensional drawing Inductive sensor Can be installed flush High switching frequency 8 5 Ø Short-circuit protection (pulsed) Solid stainless steel housing Enclosure rating IP 67 8 Ø 6.5 Ø 9 8 Connection Display LED IH0-0B8NS-VT IH0-0B8NS-VW IH0-0B8PS-VT IH0-0B8PS-VW See chapter Accessories Connector, 8, -pin 8, -pin x 0. mm² SENSICK CATALOGUE

116 IH0 Technical specifications IH0-0B8NS -VW 0B8PS -VW 0B8NS -VT 0B8PS -VT Sensing range S n Electrical configuration 0.8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 %.5 % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Sleeve diameter Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Cable, PVC, m Connector, 8, -pin 5,000 Hz mm 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a = 00 ma Stainless steel, plastic ) without load ) normally closed function available on request 5) according to EN ) (pulsed) Order information Type Order no. IH0-0B8NS-VW IH0-0B8PS-VW 6 00 IH0-0B8NS-VT IH0-0B8PS-VT SENSICK CATALOGUE 5

117 Inductive sensor, IH06, DC -wire, iniature series, Flush Sensing range.5 mm Dimensional drawing Inductive sensor Can be installed flush 0 Ø 6.5 High switching frequency Short-circuit protection (pulsed) Solid stainless steel housing Enclosure rating IP Ø 6.5 Connection Display LED IH06-B5NS-VWK IH06-B5NS-VTK IH06-B5PS-VWK IH06-B5PS-VTK See chapter Accessories Connector, 8, -pin ounting systems x 0. mm² 8, -pin 6 SENSICK CATALOGUE

118 IH06 Technical specifications IH06- B5NS -VWK B5PS -VWK B5NS -VTK B5PS -VTK Sensing range S n Electrical configuration.5 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 % 5 % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Sleeve diameter Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Cable, PVC, m Connector, 8, -pin 5,000 Hz 6.5 mm 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a = 00 ma Stainless steel, plastic ) without load ) normally closed function available on request 5) according to EN ) (pulsed) Order information Type Order no. IH06-B5NS-VWK IH06-B5PS-VWK IH06-B5NS-VTK IH06-B5PS-VTK SENSICK CATALOGUE 7

119 Inductive sensor, IH06, DC -wire, Advanced series Sensing range / mm Dimensional drawing Inductive sensor Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Solid stainless steel housing Enclosure rating IP Ø 6.5 Ø Ø Ø 6.5 Connection Display LED IH06-0BNS-VW IH06-0BPS-VW IH06-0NNS-VW IH06-0NPS-VW IH06-0BNS-VT IH06-0BPO-VT IH06-0BPS-VT IH06-0NPS-VT See chapter Accessories Connector, 8, -pin ounting systems x 0. mm² 8, -pin NC/ 8 SENSICK CATALOGUE

120 IH06 Technical specifications IH06-0BNS -VW 0BPS -VW 0BNS -VT 0BPO -VT 0BPS -VT 0NNS -VW 0NPS -VW 0NPS -VT Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function NPN PNP Installation Flush 5) Normally open Normally closed Non-flush Enclosure rating IP 67 6) ax. switching frequency Sleeve diameter Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Cable, PVC, m Connector, 8, -pin,000 Hz,800 Hz 6.5 mm 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a max Stainless steel, plastic ) without load 5) see installation notes ) of s 6) r according to EN ) (pulsed) Order information Type Order no. IH06-0BNS-VW IH06-0BPS-VW IH06-0BNS-VT IH06-0BPO-VT IH06-0BPS-VT IH06-0NNS-VW IH06-0NPS-VW IH06-0NPS-VT SENSICK CATALOGUE 9

121 Inductive sensor, IH06, DC -wire, Advanced short series Inductive sensor Sensing range / mm Enhanced sensing range High switching frequency Short-circuit protection (pulsed) Solid stainless steel housing Enclosure rating IP 67 Dimensional drawing Ø 6.5 Ø 6.5 Ø Ø Connection Display LED IH06-0BPS-VWK IH06-0BNS-VWK IH06-0NNS-VWK IH06-0NPS-VWK IH06-0BNS-VTK IH06-0BPS-VTK IH06-0BPO-VTK IH06-0NPS-VTK IH06-0NNS-VTK IH06-0NPO-VTK See chapter Accessories Connector, 8, -pin ounting systems x 0. mm² 8, -pin NC/ 0 SENSICK CATALOGUE

122 IH06 Technical specifications IH06-0BPS -VWK 0BNS -VWK 0BNS -VTK 0BPS -VTK 0BPO -VTK 0NNS -VWK 0NPS -VWK 0NPS -VTK 0NNS -VTK 0NPO -VTK Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d. V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 00 ms Hysteresis H, of s r... 0 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function PNP NPN Installation Flush 5) Normally open Normally closed Non-flush Enclosure rating IP 67 6) ax. switching frequency Sleeve diameter Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress Cable, PVC, m Connector, 8, -pin,000 Hz,500 Hz 6.5 mm 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a max Stainless steel, plastic ) without load 5) see installation notes ) of s 6) r according to EN ) (pulsed) Order information Type Order no. IH06-0BPS-VWK IH06-0BNS-VWK IH06-0BNS-VTK IH06-0BPS-VTK IH06-0BPO-VTK IH06-0NNS-VWK IH06-0NPS-VWK IH06-0NPS-VTK IH06-0NNS-VTK IH06-0NPO-VTK SENSICK CATALOGUE

123 Inductive sensor, IH0, AC/DC -wire, Non-flush Sensing range 0 mm Dimensional drawing Inductive sensor Can be installed non-flush in metal Broad supply voltage range in AC and DC Plastic housing Ø 0 Enclosure rating IP 67 Connection ounting clamps incl. Display LED IH0-0NUS-KU0 x 0.5 mm² SENSICK CATALOGUE

124 IH0 Technical specifications IH0-0NUS -KU0 Sensing range S n 0 mm Electrical configuration AC/DC -wire Supply voltage V s AC/DC V Voltage drop U d AC/DC 6.5 V / 6 V 50 ma AC ( C) 50 ma AC ( C) 00 ma DC Intermittent current I k. A (0 ms/0.5hz) in. load current 5 ma Residual current.5 ma (50 V AC) Residual current. ma (0 V AC) Residual current 0.8 ma ( V DC) Time delay before availability t v 5 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally open Installation Non-flush Cable, PUR-PVC, m Enclosure rating IP 67 ) VDE protection class ax. switching frequency AC/DC 5 Hz / 70 Hz Sleeve diameter 0 mm Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic ) of s r ) according to EN 6059 Order information Type Order no. IH0-0NUS-KU SENSICK CATALOGUE

125 Inductive sensor, IH, AC/DC -wire, Non-flush Inductive sensor Sensing range 0 mm Can be installed non-flush in metal Enhanced sensing range Broad supply voltage range in AC and DC Plastic housing Enclosure rating IP 67 ounting clamps incl. Dimensional drawing Connection Display LED Ø IH-0NUO-KU0 IH-0NUS-KU0 x 0.5 mm² SENSICK CATALOGUE

126 IH Technical specifications IH- 0NUO -KU0 0NUS -KU0 Sensing range S n 0 mm Electrical configuration AC/DC -wire Supply voltage V s AC/DC V Voltage drop U d AC/DC 6.5 V / 6 V 50 ma AC ( C) 50 ma AC ( C) 00 ma DC Intermittent current I k. A (0 ms/0.5hz) in. load current 5 ma Residual current.5 ma (50 V AC) Residual current. ma (0 V AC) Residual current 0.8 ma ( V DC) Time delay before availability t v 50 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Normally closed Normally open Installation Non-flush Cable, PUR-PVC, m Enclosure rating IP 67 ) VDE protection class ax. switching frequency 7 Hz Sleeve diameter mm Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic ) of s r ) according to EN 6059 Order information Type Order no. IH-0NUO-KU IH-0NUS-KU SENSICK CATALOGUE 5

127 Inductive sensor, IQ05, DC -wire, Flush Inductive sensor Sensing range 0.8 mm Can be installed flush High switching frequency Short-circuit protection (pulsed) Robust brass housing, nickel-plated Enclosure rating IP 67 Dimensional drawing.6.6 Connection active area IQ05-0B8NS-ZU IQ05-0B8PS-ZU x 0.06 mm² 6 SENSICK CATALOGUE

128 IQ05 Technical specifications IQ05-0B8NS -ZU 0B8PS -ZU Sensing range S n Electrical configuration 0.8 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d V ) Power consumption 0 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r 0 % Repeatability R Temperature drift, of s r ± 0 %.5 % (U b and T a constant) EC According to EN Switching output NPN PNP Output function Normally open ) Installation Flush Enclosure rating IP 67 5) ax. switching frequency Cable, PUR, m 5,000 Hz Dimensions 5 x 5 x 5 mm 6) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a = 00 ma Brass nickel-plated, plastic ) without load ) normally closed function available on request 5) according to EN ) Width x height x depth 7) (pulsed) Order information Type Order no. IQ05-0B8NS-ZU IQ05-0B8PS-ZU SENSICK CATALOGUE 7

129 Inductive sensor, IQ08, DC -wire Inductive sensor Sensing range / mm Can be installed flush or non-flush in metal High switching frequency Short-circuit protection (pulsed) Small plastic housing Enclosure rating IP 67 Dimensional drawing , active area , active area Connection Display LED IQ08-0BNS-KU0 IQ08-0BPS-KU0 IQ08-0NPS-KU0 IQ08-0BNS-KT0 IQ08-0BPS-KT0 IQ08-0NPS-KT0 See chapter Accessories Connector, 8, -pin x 0.5 mm² 8, -pin 8 SENSICK CATALOGUE

130 IQ08 Technical specifications IQ08-0BNS -KU0 0BPS -KU0 0BNS -KT0 0BPS -KT0 0NPS -KU0 0NPS -KT0 Sensing range S n Electrical configuration mm mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 0 ma ) 00 ma Time delay before availability t v ms Hysteresis H, of s r... 0 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PUR-PVC, m Connector, 8, -pin 5,000 Hz Dimensions 8 x 8 x 0 mm 6) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 8 x 8 x 9 mm 6) 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a max Plastic ) without load 5) according to EN 6059 ) of s 6) r Width x height x depth 7) (pulsed) Order information Type Order no. IQ08-0BNS-KU IQ08-0BPS-KU IQ08-0BNS-KT IQ08-0BPS-KT IQ08-0NPS-KU IQ08-0NPS-KT SENSICK CATALOGUE 9

131 Inductive sensor, IQ0, DC -wire Inductive sensor Sensing range / 6 mm Can be installed flush or non-flush in metal High switching frequency Short-circuit protection (pulsed) Plastic housing Enclosure rating IP 67 Dimensional drawing Ø active area Ø. active area Connection Display LED IQ0-0BPS-KT IQ0-0BNS-KT IQ0-0BPO-KT IQ0-06NNS-KT IQ0-06NPS-KT IQ0-0BPS-KW IQ0-0BNS-KW IQ0-06NPS-KW IQ0-06NNS-KW See chapter Accessories Connector, 8, -pin 8, -pin x 0.5 mm² /NC 0 SENSICK CATALOGUE

132 IQ0 Technical specifications IQ0-0BPS -KW 0BNS -KW 0BPS -KT 0BNS -KT 0BPO -KT 06NPS -KW 06NNS -KW 06NNS -KT 06NPS -KT Sensing range S n Electrical configuration mm 6 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 5 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r... 5 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP NPN Normally open Normally closed Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PVC, m Connector, 8, -pin,000 Hz,000 Hz Dimensions 0 x 6 x 8 mm 6) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 0 x 6 x 7 mm 6) 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a max Plastic ) without load 5) according to EN 6059 ) 6) of s r Width x height x depth 7) (pulsed) Order information Type Order no. IQ0-0BPS-KW IQ0-0BNS-KW IQ0-0BPS-KT IQ0-0BNS-KT IQ0-0BPO-KT IQ0-06NPS-KW IQ0-06NNS-KW IQ0-06NNS-KT IQ0-06NPS-KT SENSICK CATALOGUE

133 Inductive sensor, IQ, DC -wire Inductive sensor Sensing range / 6 mm Dimensional drawing 6 6 Can be installed flush or non-flush in metal 0 0 High switching frequency.. Short-circuit protection (pulsed) Plastic housing Enclosure rating IP Connection Display LED IQ-0BNS-KT0 IQ-0BPS-KT0 IQ-06NPS-KT0 IQ-0BNS-KU0 IQ-0BPS-KU0 IQ-06NPS-KU0 See chapter Accessories Connector, 8, -pin 8, -pin x 0.5 mm² SENSICK CATALOGUE

134 IQ Technical specifications IQ- 0BNS -KU0 0BPS -KU0 0BNS -KT0 0BPS -KT0 06NPS -KU0 06NPS -KT0 Sensing range S n Electrical configuration mm 6 mm DC -wire Supply voltage V s DC V Ripple U pp 0 % ) Voltage drop U d.5 V ) Power consumption 5 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r... 5 % Repeatability R % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation NPN PNP Normally open Flush Non-flush Enclosure rating IP 67 5) ax. switching frequency Cable, PUR-PVC, m Connector, 8, -pin,000 Hz,000 Hz Dimensions x 6 x 0 mm 6) Wire-break protection Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress x 6 x 9 mm 6) 7) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) of U b ) at I a max Plastic ) without load ) of s r 5) according to EN ) Width x height x depth 7) (pulsed) Order information Type Order no. IQ-0BNS-KU IQ-0BPS-KU IQ-0BNS-KT IQ-0BPS-KT IQ-06NPS-KU IQ-06NPS-KT SENSICK CATALOGUE

135 Inductive sensor, IQ0, DC -wire, Standard series Inductive sensor Sensing range 5 / 0 mm Dimensional drawing 0 Variable switching zone Programmable /NC function Short-circuit protection (pulsed) Terminal Enclosure rating IP Connection Display LED IQ0-5BPP-KK0 IQ0-0NPP-KK0 Terminal, 0 x.5 / / /NC SENSICK CATALOGUE

136 IQ0 Technical specifications IQ0-5BPP -KK0 0NPP -KK0 Sensing range S n Electrical configuration 5 mm 0 mm DC -wire Supply voltage V s DC V Voltage drop U d.5 V ) Power consumption 5 ma ) 50 ma Time delay before availability t v ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP Programmable Flush Non-flush Cable gland, Terminal, 0 x.5 Enclosure rating IP 65 ) VDE protection class ax. switching frequency 00 Hz Dimensions 0 x 0 x mm 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) at I a max and U b V ) without load Plastic ) of s r ) according to EN ) Width x height x depth 6) (pulsed) Order information Type Order no. IQ0-5BPP-KK IQ0-0NPP-KK SENSICK CATALOGUE 5

137 Inductive sensor, IQ0, DC -wire, Short version Inductive sensor Sensing range 5 / 5 mm Variable switching zone output function Short-circuit protection (pulsed) Enclosure rating IP 67 LED status-and function indicator Dimensional drawing Connection Display LED IQ0-5BPS-KC0 IQ0-5NPS-KC0 See chapter Accessories Connector,, -pin, -pin 6 SENSICK CATALOGUE

138 IQ0 Technical specifications IQ0-5BPS -KC0 5NPS -KC0 Sensing range S n 5 mm 5 mm Supply voltage V s DC V Voltage drop U d.5 V ) Power consumption 5 ma ) 50 ma Time delay before availability t v ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP Normally open Flush Non-flush Enclosure rating IP 67 ) VDE protection class ax. switching frequency Connector,, -pin 00 Hz 00 Hz Dimensions 0 x 0 x 66.5 mm 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) at I a max and U b V ) without load Plastic ) of s r ) according to EN ) Width x height x depth 6) (pulsed) Order information Type Order no. IQ0-5BPS-KC IQ0-5NPS-KC SENSICK CATALOGUE 7

139 Inductive sensor, IQ0, DC -wire, Standard series Inductive sensor Sensing range 5 / 0 mm Dimensional drawing 0 Variable switching zone Short-circuit protection (pulsed) Terminal Enclosure rating IP 68 8 Switching status LED, yellow Operating voltage status LED, green Connection Display LED IQ0-5BPP-KK IQ0-0NPP-KK Terminal, 0 x.5 NC 8 SENSICK CATALOGUE

140 IQ0 Technical specifications IQ0-5BPP -KK 0NPP -KK Sensing range S n Electrical configuration 5 mm 0 mm DC -wire Supply voltage V s DC V Voltage drop U d.8 V ) Power consumption 0 ma ) 00 ma Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP Complementary Flush Non-flush Cable gland, Terminal, 0 x.5 Enclosure rating IP 68 ) VDE protection class ax. switching frequency 50 Hz Dimensions 0 x 0 x 8 mm ) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 5) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic, PBT ) at I a max and U b 60 V ) without load ) according to EN 6059 ) Width x height x depth 5) (pulsed) Order information Type Order no. IQ0-5BPP-KK IQ0-0NPP-KK SENSICK CATALOGUE 9

141 Inductive sensor, IQ0, DC -wire, Short version Inductive sensor Sensing range 0 / 5 mm Variable switching zone Complementary output function Short-circuit protection (pulsed) Enclosure rating IP 67 LED status-and function indicator Dimensional drawing Connection Display LED IQ0-0BPP-KCK IQ0-5NPP-KCK See chapter Accessories Connector,, -pin, -pin NC 0 SENSICK CATALOGUE

142 IQ0 Technical specifications IQ0-0BPP -KCK 5NPP -KCK Sensing range S n Electrical configuration 0 mm 5 mm DC -wire Supply voltage V s DC V Voltage drop U d.5 V ) Power consumption 5 ma ) 50 ma Time delay before availability t v ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP Complementary Flush Non-flush Enclosure rating IP 67 ) VDE protection class ax. switching frequency Connector,, -pin 00 Hz Dimensions 0 x 0 x 66.5 mm 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) at I a max and U b V ) without load Plastic ) of s r ) according to EN ) Width x height x depth 6) (pulsed) Order information Type Order no. IQ0-0BPP-KCK IQ0-5NPP-KCK SENSICK CATALOGUE

143 5. Inductive sensor, IQ0, DC -wire, Short version, agnetic field immune Inductive sensor Sensing range 0 / 5 mm Dimensional drawing Variable switching zone Complementary output function Connector, 0 rotatable 0 Sensing face 0 0 Enclosure rating IP 67 Factor for all metals agnetic field immune (6058) Connection Display LED IQ0-5NPP-KC IQ0-0NPP-KC See chapter Accessories Connector,, -pin, -pin NC SENSICK CATALOGUE

144 IQ0 Technical specifications IQ0-5NPP -KC 0NPP -KC Sensing range S n Electrical configuration 5 mm 0 mm DC -wire Supply voltage V s DC V Voltage drop U d.5 V ) Power consumption 5 ma ) 00 ma Time delay before availability t v 0 ms Hysteresis H, of s r... 5 % Repeatability R 5 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function Installation PNP Complementary Non-flush Enclosure rating IP 67 ) VDE protection class ax. switching frequency Connector,, -pin 00 Hz 50 Hz Dimensions 0 x 0 x 6 mm 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Factor for all metals agnetic field immune Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) at I a max and U b V ) without load Plastic ) of s r ) according to EN ) Width x height x depth 6) (pulsed) Order information Type Order no. IQ0-5NPP-KC IQ0-0NPP-KC SENSICK CATALOGUE

145 Inductive sensor, IQ0, DC -wire, Standard series, Flush Inductive sensor Sensing range 5 mm Dimensional drawing 0 Variable switching zone Broad supply voltage range in DC Switching output: /NC Enclosure rating IP 68 Terminal connection Connection Display LED IQ0-5BDP-KK Terminal, 0 x.5 NC L L SENSICK CATALOGUE

146 IQ0 Technical specifications IQ0-5BDP -KK Sensing range S n 5 mm Electrical configuration DC -wire Supply voltage V s DC V Voltage drop U d 5 V ) 00 ma Residual current ma Temperature drift, of s r ± 0 % EC According to EN Output function Programmable Installation Flush Cable gland, Terminal, 0 x.5 Enclosure rating IP 68 ) VDE protection class ax. switching frequency 00 Hz Dimensions 0 x 0 x 8 mm ) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress ) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic, PBT ) at I a max and U b 60 V ) according to EN 6059 ) Width x height x depth ) (pulsed) Order information Type Order no. IQ0-5BDP-KK SENSICK CATALOGUE 5

147 Inductive sensor, IQ0, AC -wire, Standard series, Flush Inductive sensor Sensing range 5 mm Dimensional drawing 0 Variable switching zone Broad supply voltage range in AC Switching output: /NC Enclosure rating IP 68 Terminal connection Connection Display LED IQ0-5BAP-KK Terminal, 0 x.5 NC N L L N 6 SENSICK CATALOGUE

148 IQ0 Technical specifications IQ0-5BAP -KK Sensing range S n 5 mm Electrical configuration AC -wire Supply voltage V s AC V Voltage drop U d V 500 ma Intermittent current I k A (0 ms/0.hz) Residual current.95 ma Temperature drift, of s r ± 0 % EC According to EN Output function Programmable Installation Flush Cable gland, Terminal, 0 x.5 Enclosure rating IP 68 ) VDE protection class ax. switching frequency 0 Hz Dimensions 0 x 0 x 8 mm ) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress ) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic, PBT ) according to EN 6059 ) Width x height x depth ) (pulsed) Order information Type Order no. IQ0-5BAP-KK SENSICK CATALOGUE 7

149 Inductive sensor, IQ0, AC/DC -wire, Standard series Inductive sensor Sensing range 5 / 0 mm Dimensional drawing 0 Variable switching zone Broad supply voltage range in AC and DC Programmable switching output: or NC Enclosure rating IP 65 Terminal connection Connection Display LED IQ0-5BUP-KK0 IQ0-0NUP-KK0 Terminal, 0 x.5 / / L () N () 8 SENSICK CATALOGUE

150 IQ0 Technical specifications IQ0-5BUP -KK0 0NUP -KK0 Sensing range S n 5 mm 0 mm Electrical configuration AC/DC -wire Supply voltage V s AC/DC V Voltage drop U d AC/DC 6.5 V / 6 V 50 ma AC ( C) 50 ma AC ( C) 00 ma DC Intermittent current I k. A (0 ms/0.5hz) in. load current > 5 ma Residual current.5 ma (50 V AC) Residual current. ma (0 V AC) Residual current 0.8 ma ( V DC) Time delay before availability t v 8 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Output function Programmable Installation Flush Non-flush Cable gland, Terminal, 0 x.5 Enclosure rating IP 65 ) VDE protection class ax. switching frequency AC/DC 0 Hz / 55 Hz Dimensions 0 x 0 x mm ) Power-up pulse suppression Shock/vibration stress 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material Plastic ) of s r ) according to EN 6059 ) Width x height x depth Order information Type Order no. IQ0-5BUP-KK IQ0-0NUP-KK SENSICK CATALOGUE 9

151 Inductive sensor, IQ80, DC -wire, Non-flush Inductive sensor Sensing range 60 mm Dimensional drawing Adjustable switching distance between 0 to 60 mm 8 7 Programmable /NC function Short-circuit protection (pulsed) Terminal connection Enclosure rating IP Connection Potentiometer Display LED IQ80-60NPP-KK0 Terminal, 0 x.5 NC SENSICK CATALOGUE

152 IQ80 Technical specifications IQ80-60NPP -KK0 Sensing range S n Electrical configuration 60 mm DC -wire Supply voltage V s DC V Voltage drop U d.5 V ) Power consumption 5 ma ) 50 ma Time delay before availability t v 50 ms Hysteresis H, of s r... 5 % Repeatability R 0 % (U b and T a constant) ) Temperature drift, of s r ± 0 % EC According to EN Switching output Output function PNP Programmable Cable gland, Terminal, 0 x.5 Enclosure rating IP 65 ) VDE protection class ax. switching frequency Hz Dimensions 80 x 0 x 05 mm 5) Short-circuit protection Reverse polarity protection Power-up pulse suppression Shock/vibration stress 6) 0 g, ms/ Hz, mm Ambient temperature T a -5 C C Housing material ) at I a max and U b V ) without load Plastic ) of s r ) according to EN ) Width x height x depth 6) (pulsed) Order information Type Order no. IQ80-60NPP-KK SENSICK CATALOGUE 5

153 Inductive sensor, IQ80, DC -wire Inductive sensor Sensing range.55 / 50 mm Can be installed non-flush, flush or over flush in metal Switching distance 50 mm (flush or over flush installation) switching distance max. 5.5 mm reduced (non-flush installation) Antivalent output functions Connector (rotable in 5 -steps) Enclosure rating IP 67 Dimensional drawing Connection IQ80-50BPP-KC0, -pin See chapter Accessories Connector,, -pin wht NC 5 SENSICK CATALOGUE