Certificate of Accreditation

Transcription

1 PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:. (Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard: ISO/IEC 17025:2005 This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated January 2009): Dimensional, Mass, Force and Weighing Devices, Mechanical and Calibration (As detailed in the supplement) Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body s duty to observe and comply with the said rules. For PJLA: Initial Accreditation Date: Issue Date: Expiration Date: March 07, 2018 March 07, 2018 March 31, 2020 Tracy Szerszen President/Operations Manager Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan Accreditation No.: Certificate No.: L The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: Page 1 of 11

2 Contact Name: José F. Ramirez Gaytan Phone: Dimensional RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE AND Outside Micrometer FO 0.5 mm to mm (7.03 x x 10-6 L) µm Gage Block grade 0 JIS B 7502 Caliper FO 0.5 mm to mm (7.03 x x 10-4 L) µm Gage Block Grade 0 JIS B 7507 Indicator FO mm to 51 mm 1.4 µm Gage Block Grade 0 JIS B 7503 Height Gage, QM Height Linear Height FO 10 mm to 610 mm ( x 10-5 L) µm Gage Block Grade 0 Master Height JIS B 7517 Pin Gages FO mm to 76.2 mm 1.4 µm Micrometer Thread Plug Gage Major Diameter FO Thread Plug Gage Pitch Diameter FO ASME B to µm Digital Micrometer ANSI/ASME B to µm Digital Micrometer Three Wire ANSI/ASME B1.2 Mass, Force and Weighing Devices Analytical Balances O Balances and Scales O RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE 1 mg to 200 g (Res.= g) 200 g to 2 kg (Res.= 0.1 g) 2 kg to 20 kg (Res.= 0.1 g) 20 kg to 200 kg (Res.= 1 g) 100 kg to kg (Res.= 0.1 kg) AND g MASS CLASS F1 Euramet cg g 0.15 g 1.4 g MASS CLASS M1 Euramet cg kg Mechanical MEASURED INSTRUMENT, AND Pressure FO kpa to kpa 0.15 % of reading Pressure Calibrator Fluke G kpa to kpa 0.15 % of reading Manometers Fluke 700G kpa to kpa 0.2 % of reading Series kpa to kpa 0.2 % of reading Issue: 03/2018 This supplement is in conjunction with certificate #L Page 2 of 11

3 Mechanical AND Torque Wrenches FO 0.5 N m to 5.65 N m ( x 10-3 T) N m Torque Analyzer System 3.3 N m to 33.9 N m ( T) N m Sturtevant-Richmond Torque Analyzers, Transducers F 33.9 N m to N m ( x 10-3 T) N m 2.82 N m to N m 0.22 % of reading Torque Wheel and Dead Weighs DC Voltage FO DC Current FO Resistance FO AND 33 mv to 329 mv 60 µv/v + 30 µv 0.33 V to 3.29 V 50 µv/v + 50 µv 3.3 V to 32.9 V 50 µv/v + 50 µv 33 V to 329 V 12 µv/v + 21 mv 330 V to V µv/v + 3 mv 33 µa to 329 µa 0.15 ma/a µa 0.33 ma to 3.29 ma 0.1 ma/a µa 3.3 ma to 32.9 ma 0.1 ma/a µa 33 ma to 329 ma 0.1 ma/a µa 0.33 A to 1.09 A 0.2 ma/a + 40 µa 1.1 A to 2.99 A 0.38 ma/a + 40 µa 3 A to 11 A 0.5 ma/a µa 11 A to 20 A 1 ma/a ma/a 1.1 Ω to 11 Ω 0.22 mω/ω 11 Ω to 33 Ω 0.19 mω/ω 33 Ω to 109 Ω 0.74 mω/ω 109 Ω to 330 Ω 1.5 mω/ω 0.33 kω to 1.09 kω 4.8 mω/ω 1.09 kω to 3.3 kω 22 mω/ω 3.3 kω to 10.9 kω 54 mω/ω 10.9 kω to 33 kω 0.14 Ω/Ω 33 kω to 109 kω 0.52 Ω/Ω 109 kω to 330 kω 1.6 Ω/Ω 330 kω to 1.09 MΩ 8.7 Ω/Ω 1.09 MΩ to 3.3 MΩ 72 Ω/Ω Issue: 03/2018 This supplement is in conjunction with certificate #L Page 3 of 11

4 AND 3.3 MΩ to 10.9 MΩ 0.14 kω/ω Resistance FO 10.9 MΩ to 33 MΩ 1.9 kω/ω 33 MΩ to 400 MΩ 0.2 kω/ω 400 MΩ to 640 MΩ 0.49 kω/ω 640 MΩ to 1 GΩ 1.1 MΩ/Ω 10 Hz to 45 khz 1 mv to mv 800 mv/v + 6 µv 45 Hz to 10 khz 1 mv to mv 150 mv/v + 6 µv 10 khz to 20 khz 1 mv to mv 200 mv/v + 6 µv 20 khz to 50 khz 1 mv to mv mv/v + 6 µv 50 khz to 100 khz 1 mv to mv mv/v + 12 µv 100 khz to 500 khz 1 mv to mv mv/v + 50 µv 10 Hz to 45 khz 33 mv to mv 300 mv/v + 8 µv 45 Hz to 10 khz 33 mv to mv 145 mv/v + 8 µv 10 khz to 20 khz 33 mv to mv 160 mv/v + 8 µv 20 khz to 50 khz 33 mv to mv 350 mv/v + 8 µv 50 khz to 100 khz 33 mv to mv 800 mv/v + 32 µv 100 khz to 500 khz 33 mv to mv mv/v + 70 µv 10 Hz to 45 khz 0.33 V to V 300 mv/v + 50 µv 45 Hz to 10 khz 0.33 V to V 150 mv/v + 60 µv 10 khz to 20 khz 0.33 V to V 190 mv/v + 60 µv 20 khz to 50 khz 0.33 V to V 300 mv/v + 50 µv 50 khz to 100 khz 0.33 V to V 700 mv/v µv 100 khz to 500 khz 0.33 V to V mv/v µv 10 Hz to 45 khz 3.3 V to V 300 mv/v µv Issue: 03/2018 This supplement is in conjunction with certificate #L Page 4 of 11

5 AND 45 Hz to 10 khz 3.3 V to V 150 mv/v µv 10 khz to 20 khz 3.3 V to V 240 mv/v µv 20 khz to 50 khz 3.3 V to V 350 mv/v µv 50 khz to 100 khz 3.3 V to V 900 mv/v µv 45 Hz to 1 khz 33 V to V 190 mv/v µv 1 khz to 10 khz 33 V to V 200 mv/v µv 10 khz to 20 khz 33 V to V 250 mv/v µv 20 khz to 50 khz 33 V to V 300 mv/v µv 50 khz to 100 khz 33 V to V mv/v µv 45 Hz to 1 khz 330 V to V 300 mv/v µv 1 khz to 5 khz 330 V to V 250 mv/v µv 5 khz to 10 khz 330 V to V 300 mv/v µv 10 Hz to 20 Hz 29 µa to µa 2 µa/a µa 20 Hz to 45 Hz 29 µa to µa 1.5 µa/a µa 45 Hz to 1 khz 29 µa to µa 1.25 µa/a µa 1 khz to 5 khz 29 µa to µa 3 µa/a µa 5 khz to 10 khz 29 µa to µa 8 µa/a µa 10 khz to 30 khz 29 µa to µa 16 µa/a µa 10 Hz to 20 Hz 0.33 ma to ma 2 µa/a µa 20 Hz to 45 Hz 0.33 ma to ma 1.5 A/A A 45 Hz to 1 khz 0.33 ma to ma 1.3 A/A A 1 khz to 5 khz 0.33 ma to ma 3 A/A A Issue: 03/2018 This supplement is in conjunction with certificate #L Page 5 of 11

6 AND 5 khz to 10 khz 0.33 ma to ma 8 A/A A 10 khz to 30 khz 0.33 ma to ma 16 A/A A 10 Hz to 20 Hz 3.3 ma to ma 1.8 A/A A 20 Hz to 45 Hz 3.3 ma to ma 0.9 A/A A 45 Hz to 1 khz 3.3 ma to ma 1.3 A/A A 1 khz to 5 khz 3.3 ma to ma 3 A/A A 5 khz to 10 khz 3.3 ma to ma 5 A/A A 10 khz to 30 khz 3.3 ma to ma 1 A/A A 10 Hz to 20 Hz 33 ma to ma 1.8 A/A A 20 Hz to 45 Hz 33 ma to ma 0.9 A/A A 45 Hz to 1 khz 33 ma to ma 4 A/A A 1 khz to 5 khz 33 ma to ma 1 A/A A 5 khz to 10 khz 33 ma to ma 0.4 A/A A 10 khz to 30 khz 33 ma to ma 1 A/A A 10 Hz to 45 Hz 0.33 A to A 1.8 A/A A 45 Hz to 1 khz 0.33 A to A 0.5 A/A A 1 khz to 5 khz 0.33 A to A 2.5 A/A A 5 khz to 10 khz 0.33 A to A 2.5 A/A A 10 Hz to 45 Hz 1.1 A to A 150 A/A A 45 Hz to 1 khz 1.1 A to A 50 A/A A 1 khz to 5 khz 1.1 A to A 50 A/A A 5 khz to 10 khz 1.1 A to A 200 A/A A Issue: 03/2018 This supplement is in conjunction with certificate #L Page 6 of 11

7 Certificate of Accreditation: Supplement AND 45 Hz to 100 Hz 3 A to A 100 A/A A 100 Hz to 1 khz 3 A to A 200 A/A A 1 khz to 5 khz 3 A to A 300 A/A A 45 Hz to 100 Hz 11 A to 20.5 A A/A A 100 Hz to 1 khz 11 A to 20.5 A A/A A 1 khz to 5 khz 11 A to 20.5 A A/A A 220 pf to pf 0.5 nf/f nf Capacitance FO 0.4 nf to nf 0.5 nf/f nf Thermocouple Type B FO 1.1 nf to nf 0.5 nf/f nf 3.3 nf to nf 0.25 nf/f nf 11 nf to nf 0.25 nf/f nf 33 nf to nf 0.25 nf/f nf 110 nf to nf 0.25 nf/f + 1 nf 0.33 µf to µf 0.25 nf/f + 3 nf 1.1 µf to µf 0.25 nf/f + 10 nf 3.3 µf to µf 0.4 nf/f + 30 nf 11 µf to µf 0.45 nf/f nf 33 µf to µf 0.45 nf/f nf 110 µf to µf 0.45 µf/f + 1 µf 0.33 mf to mf 0.45 µf/f + 3 µf 1.1 mf to mf 0.45 µf/f + 10 µf 3.3 mf to mf 0.45 µf/f + 10 µf 11 mf to mf 0.75 µf/f + 30 µf 33 mf to 110 mf 1.1 µf/f µf 600 ºC to 800 ºC 0.42 ºC Simulation of 800 ºC to ºC 0.34 ºC Thermocouple Output ºC to ºC 0.3 ºC ºC to ºC 0.26 ºC Issue: 03/2018 This supplement is in conjunction with certificate #L Page 7 of 11

8 Thermocouple Type C FO Thermocouple Type E FO Thermocouple Type J FO Thermocouple Type K FO Thermocouple Type L FO Thermocouple Type N FO Thermocouple Type R FO AND 0 ºC to 150 ºC 0.23 ºC Simulation of 150 ºC to 650 ºC 0.19 ºC Thermocouple Output 650 ºC to ºC 0.23 ºC 650 ºC to ºC 0.38 ºC ºC to ºC 0.63 ºC -250 ºC to -100 ºC 0.38 ºC -100 ºC to -25 ºC 0.12 ºC -25 ºC to 350 ºC 0.1 ºC 350 ºC to 650 ºC 0.12 ºC 650 ºC to ºC 0.16 ºC -210 ºC to -100 ºC 0.2 ºC -100 ºC to -30 ºC 0.12 ºC -30 ºC to 150 ºC 0.1 ºC 150 ºC to 760 ºC 0.13 ºC 760 ºC to ºC 0.18 ºC -200 ºC to -100 ºC 0.25 ºC -100 ºC to -25 ºC 0.14 ºC -25 ºC to 120 ºC 0.12 ºC 120 ºC to ºC 0.19 ºC ºC to ºC 0.3 ºC -200 ºC to -100 ºC 0.37 ºC -100 ºC to 800 ºC 0.26 ºC 800 ºC to 900 ºC 0.17 ºC -200 ºC to -100 ºC 0.3 ºC -100 ºC to -25 ºC 0.17 ºC -25 ºC to 120 ºC 0.15 ºC 120 ºC to 410 ºC 0.14 ºC 410 ºC to ºC 0.21 ºC 0 ºC to 250 ºC 0.48 ºC 250 ºC to 400 ºC 0.28 ºC 400 ºC to ºC 0.26 ºC ºC to ºC 0.3 ºC Issue: 03/2018 This supplement is in conjunction with certificate #L Page 8 of 11

9 Thermocouple Type S FO Thermocouple Type T FO Thermocouple Type U FO RTD Type Pt 385, 100Ω FO RTD Type Pt 3 926, 100Ω FO RTD Type Pt 3 916, 100Ω FO RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE AND 0 ºC to 250 ºC 0.47 ºC Simulation of 250 ºC to ºC 0.3 ºC Thermocouple Output ºC to ºC 0.28 ºC ºC to ºC 0.34 ºC -250 ºC to -150 ºC 0.48 ºC -150 ºC to 0 ºC 0.18 ºC 0 ºC to 120 ºC 0.12 ºC 120 ºC to 400 ºC 0.1 ºC -200 ºC to 0 ºC 0.56 ºC 0 ºC to 600 ºC 0.27 ºC -200 ºC to -80 ºC 0.04 ºC Simulation of -80 ºC to 0 ºC 0.05 ºC RTD Output Fluke 5502A 0 ºC to 100 ºC 0.07 ºC 100 ºC to 300 ºC 0.08 ºC 300 ºC to 400 ºC 0.09 ºC 400 ºC to 630 ºC 0.1 ºC 630 ºC to 800 ºC 0.21 ºC 200 ºC to -80 ºC 0.04 ºC -80 ºC to 0 ºC 0.05 ºC 0 ºC to 100 ºC 0.07 ºC 100 ºC to 300 ºC 0.08 ºC 300 ºC to 400 ºC 0.09 ºC 400 ºC to 630 ºC 0.1 ºC -200 ºC to -190 ºC 0.25 ºC -190 ºC to -80 ºC 0.04 ºC -80 ºC to 0 ºC 0.05 ºC 0 ºC to 100 ºC 0.06 ºC 100 ºC to 260 ºC 0.06 ºC 260 ºC to 300 ºC 0.07 ºC 300 ºC to 400 ºC 0.08 ºC 400 ºC to 600 ºC 0.08 ºC 600 ºC to 630 ºC 0.21 ºC Issue: 03/2018 This supplement is in conjunction with certificate #L Page 9 of 11

10 RTD Type Pt 385, 200Ω FO RTD Type Pt 385, 500Ω FO RTD Type Pt 385, 1 000Ω FO RTD PtNi 385, 120Ω (Ni120) FO RTD Cu 427, 10Ω FO RANGE OR NOMINAL DEVICE SIZE AS APPROPRIATE AND -200 ºC to -80 ºC 0.04 ºC Simulation of -80 ºC to 0 ºC 0.04 ºC RTD Output Fluke 5502A 0 ºC to 100 ºC 0.04 ºC 100 ºC to 260 ºC 0.05 ºC 260 ºC to 300 ºC 0.12 ºC 300 ºC to 400 ºC 0.13 ºC 400 ºC to 600 ºC 0.14 ºC 600 ºC to 630 ºC 0.16 ºC -200 ºC to -80 ºC 0.04 ºC -80 ºC to 0 ºC 0.05 ºC 0 ºC to 100 ºC 0.05 ºC 100 ºC to 260 ºC 0.06 ºC 260 ºC to 300 ºC 0.08 ºC 300 ºC to 400 ºC 0.08 ºC 400 ºC to 600 ºC 0.09 ºC 600 ºC to 630 ºC 0.11 ºC -200 ºC to 80 ºC 0.04 ºC -80 ºC to 0 ºC 0.05 ºC 0ºC to 100 ºC 0.04 ºC 100 ºC to 260 ºC 0.05 ºC 260 ºC to 300 ºC 0.06 ºC 300º C to 400 ºC 0.07 ºC 400 ºC to 600 ºC 0.07 ºC 600 ºC to 630 ºC 0.23 ºC -80 ºC to 0 ºC 0.08 ºC 0 ºC to 100 ºC 0.08 ºC 100 ºC to 260 ºC 0.14 ºC -100 ºC to 260 ºC 0.3 ºC Issue: 03/2018 This supplement is in conjunction with certificate #L Page 10 of 11

11 1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree. 2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity. 3. The presence of a superscript F means that the laboratory performs calibration of the indicated parameter at its fixed location. Example: Outside Micrometer F would mean that the laboratory performs this calibration at its fixed location. 4. The presence of a superscript O means that the laboratory performs calibration of the indicated parameter onsite at customer locations. Example: Outside Micrometer O would mean that the laboratory performs this calibration onsite at the customer s location. 5. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside Micrometer FO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations. 6. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location. 7. The term L represents length in inches or millimeters as appropriate to the uncertainty statement. 8. The term T represents torque in N m (including SI multiple and submultiple units) for the international system of units (the SI) or ozf in, lbf in and lbf ft for the USC system of units. Issue: 03/2018 This supplement is in conjunction with certificate #L Page 11 of 11