SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSLI Z

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSLI Z TEKTRONIX, INC East 43 RD Street Suite D Tulsa, OK Mark Jackson Phone: CALIBRATION Valid To: September 30, 2017 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Dimensional Parameter/Equipment Range CMC 2, 4 ( ) Comments Thread Plugs Simple Pitch Up to 10 in ( L) µin Lab concept 1000 w/ Class Z thread wires Micrometers Inside Up to 12 in (12 to 36) in ( L) µin ( L) µin Lab concept 1000 Outside Up to 5 in (5 to 36) in (11 + 1L) µin ( L) µin Master gage blocks Calipers Up to 36 in 580 µin Master gage blocks Height Gages Up to 36 in ( L) µin Master gage blocks Indicators Up to 2 in 78 µin P&W Model C Supermicrometer TM (A2LA Cert. No ) 03/23/2016 Page 1 of 18

2 Parameter/Equipment Range CMC 2, 4 ( ) Comments Depth Gages Up to 36 in ( L) µin Master gage blocks Flatness Up to 5 in 3.3 µin Master flat Length and Diameter Up to 5 in (5 to 36) in ( L) µin ( L) µin Lab concept 1000 Master gage blocks II. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 5 ( ) Comments DC Voltage Generate Up to 220 mv 220 mv to 2.2 V (2.2 to 11) V (11 to 22) V (22 to 220) V 220 V to 1.1 kv 11 µv/v µv 8.2 µv/v + 1 µv 8.1 µv/v µv 8.1 µv/v µv 9.3 µv/v + 80 µv 11 µv/v µv Fluke 5700A DC Voltage Measure Up to 200 mv (0.2 to 2) V (2 to 20) V (20 to 200) V (200 to 1050) V 5.5 µv/v µv 3.8 µv/v µv 3.6 µv/v + 5 µv 5.6 µv/v + 50 µv 5.7 µv/v µv Fluke 8508A-01 (1 to 10) kv 0.12 % Ross Engineering VD75 w/agilent DC Current Measure (0 to 200) µa (0.2 to 20) ma (2 to 20) ma (20 to 200) ma (0.2 to 2) A (2 to 20) A (0 to 20) A (20 to 100) A 48 µa/a na 35 µa/a + 4 na 38 µa/a + 40 na 74 µa/a µa % + 16 µa % µa % % Fluke 8508A-01 Fluke Y5020 w/agilent 3458A-002 Ohm-Labs CS-100 w/ Agilent 3458A-002 (A2LA Cert. No ) 03/23/2016 Page 2 of 18

3 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments DC Current Generate Up to 220 µa 220 µa to 2.2 ma (2.2 to 22) ma (22 to 220) ma 220 ma to 2.2A 52 µa/a + 8 na 51 µa/a + 8 na 52 µa/a + 8 na 61 µa/a µa 83 µa/a + 25 µa Fluke 5700A (2.2 to 11) A % µa Fluke 5700A/5725A (11 to 20.5) A % µa Clamp-On Only (20 to 1000) A 0.26 % w/ Fluke 5500 coil DC Resistance Generate 3 Up to 11 Ω (11 to 33) Ω (33 to 110) Ω (110 to 330) Ω 330 to 1.1 kω (1.1 to 3.3) kω (3.3 to 11) kω (11 to 33) kω (33 to 110) kω (110 to 330) kω 330 kω to 1.1 MΩ (1.1 to 3.3) MΩ (3.3 to 11) MΩ (11 to 33) MΩ (33 to 110) MΩ (110 to 330) MΩ 330 MΩ to 1.1 GΩ 33 µω/ω + 1 mω 25 µω/ω mω 23 µω/ω mω 23 µω/ω + 2 mω 23 µω/ω + 2 mω 24 µω/ω mω 24 µω/ω + 20 mω 24 µω/ω mω 24 µω/ω mω 26 µω/ω + 2 Ω 26 µω/ω + 2 Ω 49 µω/ω + 30 Ω 0.01 % + 50 Ω % kω 0.04 % + 3 kω 0.23 % kω 12 mω/ω MΩ (1 to 10) GΩ (10 to 100) GΩ 10 GΩ to 1TΩ 1.1 % 1.6 % 3.1 % IET Labs HRRS-B-3-1G-5KV Fixed Values 1 Ω 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 1 MΩ 93 µω 0.17 mω 0.27 mω 0.55 mω 1.6 mω 3.1 mω 12 mω 23 mω 0.11 Ω 0.21 Ω 1.3 Ω 2.5 Ω 18 Ω Fluke 5700A (A2LA Cert. No ) 03/23/2016 Page 3 of 18

4 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments Resistance Generate, Fixed Values (cont) 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 40 Ω 0.4 kω 0.93 kω 11 kω Fluke 5700A DC Resistance Measure 3 (0 to 2) Ω (2 to 20) Ω (20 to 200) Ω (0.2 to 2) kω (2 to 20) kω (20 to 200) kω (0.2 to 2) MΩ (2 to 20) MΩ (20 to 200) MΩ (0.2 to 2) GΩ (2 to 20) GΩ 19 µω/ω + 5 µω 9.9 µω/ω + 18 µω 8.2 µω/ω + 60 µω 8.1 µω/ω mω 8.1 µω/ω + 6 mω 8.2 µω/ω + 60 mω 11 µω/ω Ω 21 µω/ω Ω % + 12 kω % MΩ 0.14 % + 12 MΩ Fluke 8508A-01 HV mode HV mode Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments AC Voltage Generate Up to 2.2 mv 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 2.2 mv/v µv 1.3 mv/v µv 1.0 mv/v µv 1.7 mv/v µv 2.4 mv/v + 7 µv 4.1 mv/v + 13 µv 6.0 mv/v + 25 µv 7.7 mv/v + 25 µv Fluke 5700A (2.2 to 22) mv 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz % + 5 µv % + 5 µv % + 5 µv % + 5 µv 0.09 % + 7 µv 0.12 % + 12 µv 0.18 % + 25 µv 0.36 % + 25 µv (22 to 220) mv 40 Hz to 20 khz % + 13 µv % + 8 µv % + 8 µv % + 8 µv (A2LA Cert. No ) 03/23/2016 Page 4 of 18

5 Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments AC Voltage Generate (cont) (22 to 220) mv (300 to 500) khz 500 khz to 1 MHz % + 25 µv 0.11 % + 25 µv 0.17 % + 35 µv 0.35 % + 80 µv Fluke 5700A 220 mv to 2.2 V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz % + 80 µv % + 25 µv 78 µv/v + 6 µv % + 16 µv % + 70 µv % µv 0.11 % µv 0.22 % µv (2.2 to 22) V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.05 % µv % µv 78 µv/v + 60 µv % µv % µv % µv 0.13 % µv 0.27 % µv (22 to 220) V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.05 % + 8 mv % mv % mv % mv 0.05 % + 8 mv 0.15 % + 90 mv 0.47 % + 90 mv 1.2 mv/v mv (220 to 750) V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.05 % + 8 mv % mv 83 µv/v mv % mv 0.05 % + 8 mv 0.15 % + 90 mv 0.47 % + 90 mv 1.2 mv/v mv (220 to 750) V (30 to 50) khz % + 11 mv 0.24 % + 45 mv Fluke 5700A w/ Fluke 5725A (220 to 1100) V (15 to 50) Hz 50 Hz to 1 khz 0.04 % + 16 mv 87 µv/v mv Fluke 5700A (1 to 20) khz (20 to 30) khz 98 µv/v + 4 mv % + 6 mv % + 11 mv Fluke 5700A w/ Fluke 5725A (A2LA Cert. No ) 03/23/2016 Page 5 of 18

6 Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments AC Voltage Measure (Up to 10) mv (1 to 40) Hz (1 to 20) khz % + 3 µv % µv % µv % µv 0.41 % µv 3.3 mv/v + 2 µv Agilent 3458A-002 (10 to 100) mv (1 to 40) Hz (1 to 20) khz 300 khz to 1 MHz (1 to 2) MHz 57 µv/v + 4 µv 57 µv/v + 2 µv % + 2 µv % + 2 µv % + 3 µv 0.25 % + 10 µv 0.82 % + 10 µv 13 mv/v + 10 µv 100 mv to 1 V (1 to 40) Hz (1 to 20) khz 300 khz to 1 MHz (1 to 2) MHz 57 µv/v + 40 µv 57 µv/v + 20 µv % + 20 µv % + 20 µv % + 20 µv 0.25 % µv 0.82 % µv 13 mv/v µv (1 to 10) V (1 to 40) Hz (1 to 20) khz 300 khz to 1 MHz (1 to 2) MHz 57 µv/v + 4 mv 57 µv/v + 2 mv % + 2 mv % + 2 mv % + 2 mv 0.25 % + 10 mv 0.82 % + 10 mv 13 mv/v + 10 mv (10 to 100) V (1 to 40) Hz 40 Hz to 20 khz 300 khz to 1 MHz % + 4 mv % + 2 mv % + 2 mv % + 2 mv 0.33 % + 10 mv 13 mv/v + 10 mv (100 to 700) V (1 to 40) Hz (1 to 20) khz % + 40 mv % + 20 mv % + 20 mv % + 20 mv 0.25 % + 20 mv (1 to 10) kv Up to 1 khz 0.61 % Ross Engineering VD75 w/agilent (A2LA Cert. No ) 03/23/2016 Page 6 of 18

7 Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments AC Current Generate (Up to 220) µa (1 to 5) khz (5 to 10) khz % + 25 na % + 20 na % + 16 na % + 40 na 1.7 ma/a + 80 na Fluke 5700A 220 µa to 2.2 ma (1 to 5) khz (5 to 10) khz % + 40 na % + 35 na % + 35 na % na 1.7 ma/a na (2.2 to 22) ma (1 to 5) khz (5 to 10) khz % na % na % na % na 1.7 ma/a na (22 to 220) ma (1 to 5) khz (5 to 10) khz % + 4 µa % µa % µa % + 40 µa 1.7 ma/a + 80 µa 220 ma to 2.2 A 20 Hz to 1 khz (1 to 5) khz (5 to 10) khz 8.8 ma/a µa % + 35 µa % + 80 µa (2.2 to 11) A 40 Hz to 1kHz (1 to5) khz (5 to 10) khz % µa % µa 3.7 ma/a µa (11 to 20.5) A (45 to 100) Hz 100 Hz to 1 khz (1 to 5) khz 0.11 % µa 0.13 % µa 2.3 ma/a µa Clamp-On Only Toroidal (20 to 1000) A (20 to 1000) A (45 to 65) Hz (65 to 440) Hz 0.67 % 0.68 % w/ Fluke 5500 coil Non-Toroidal (20 to 1000) A (20 to 1000) A (45 to 65) Hz (65 to 440) Hz 0.84 % 0.85 % w/ Fluke 5500 coil (A2LA Cert. No ) 03/23/2016 Page 7 of 18

8 Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments AC Current Measure Up to 200 µa 10 Hz to 10 khz (10 to 30) khz (30 to 100) khz % + 24 na % + 24 na 0.35 % + 24 na Fluke 8508A-01 (0.2 to 2) ma 10 Hz to 10 khz (10 to 30) khz (30 to 100) khz % µa % µa 0.31 % µa (2 to 20) ma 10 Hz to 10 khz (10 to 30) khz (30 to 100) khz % µa % µa 0.44 % µa (20 to 200) ma 10 Hz to 10 khz (10 to 30) khz % + 24 µa % + 24 µa (0.2 to 2) A 10 Hz to 2 khz (2 to 10) khz (10 to 30) khz 0.07 % ma 0.10 % ma 0.62 % ma (2 to 20) A 10 Hz to 2 khz (2 to 10) khz % ma 0.20 % ma (1 to 20) A DC to 1 khz (1 to 5) khz % % Fluke Y5020 w/ Agilent 3458A-002 Parameter/Equipment Range CMC 2 ( ) Comments Electrical Simulation of Thermocouple Indicators Type B (600 to 800) C (800 to 1000) C (1000 to 1550) C (1550 to 1820) C 0.37 C 0.31 C 0.27 C 0.30 C Type C (0 to 150) C (150 to 650) C (650 to 1000) C (1000 to 1800) C (1800 to 2316) C 0.28 C 0.25 C 0.27 C 0.41 C 0.67 C Type E (-250 to -100) C (-100 to -25) C (-25 to 350) C (350 to 650) C (650 to 1000) C 0.42 C 0.17 C 0.16 C 0.17 C 0.21 C (A2LA Cert. No ) 03/23/2016 Page 8 of 18

9 Parameter/Equipment Range CMC 2 ( ) Comments Electrical Simulation of Thermocouple Indicators (cont) Type J (-210 to -100) C (-100 to -30) C (-30 to 150) C (150 to 760) C (760 to 1200) C 0.25 C 0.17 C 0.18 C 0.18 C 0.22 C Fluke 5520-SC1100 Type K (-200 to -100) C (-100 to -25) C (-25 to 120) C (120 to 1000) C (1000 to 1372) C 0.28 C 0.21 C 0.19 C 0.25 C 0.33 C Type L (-200 to -100) C (-100 to 800) C (800 to 900) C 0.31 C 0.24 C 0.18 C Type N (-200 to -100) C (-100 to -25) C (-25 to 120) C (120 to 410) C (410 to 1300) C 0.34 C 0.23 C 0.20 C 0.19 C 0.24 C Type R (0 to 250) C (250 to 400) C (400 to 1 000) C (1000 to 1767) C 0.47 C 0.30 C 0.29 C 0.34 C Type S (0 to 250) C (250 to 1000) C (1000 to 1400) C (1400 to 1767) C 0.40 C 0.32 C 0.33 C 0.39 C Type T (-250 to -150) C (-150 to 0) C (0 to 120) C (120 to 400) C 0.51 C 0.22 C 0.17 C 0.16 C Type U (-200 to 0) C (0 to 600) C 0.45 C 0.25 C Type J Type K Type T Type E (-210 to 1200) C (-200 to 1372) C (-250 to 400) C (-250 to 1000) C ºC ºC ºC ºC Fluke 5700A, Agilent 3458A, ice point, half junctions (A2LA Cert. No ) 03/23/2016 Page 9 of 18

10 Parameter/Equipment Range CMC 2 ( ) Comments Electrical Simulation of RTDs Pt 385, 100 Ω (-200 to -80) C (-80 to 0) C (0 to 100) C (100 to 300) C (300 to 400) C (400 to 630) C (630 to 800) C 0.15 C 0.15 C 0.16 C 0.22 C Pt 3926, 100 Ω (-200 to -80) C (-80 to 0) C (0 to 100) C (100 to 300) C (300 to 400) C (400 to 630) C 0.15 C 0.17 C Pt 3916, 100 Ω (-200 to -190) C (-190 to -80) C (-80 to 0) C (0 to 100) C (100 to 260) C (260 to 300) C (300 to 400) C (400 to 600) C (600 to 630) C 0.37 C 0.16 C 0.22 C Pt 385, 200 Ω (-200 to -80) C (-80 to 0) C (0 to 100) C (100 to 260) C (260 to 300) C (300 to 400) C (400 to 600) C (600 to 630) C 0.15 C 0.16 C 0.17 C 0.18 C Pt 385, 500 Ω (-200 to -80) C (-80 to 0) C (0 to 100) C (100 to 260) C (260 to 300) C (300 to 400) C (400 to 600) C (600 to 630) C 0.15 C (A2LA Cert. No ) 03/23/2016 Page 10 of 18

11 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments Electrical Simulation of RTDs (cont) Pt 385, 1 kω (-200 to -80) C (-80 to 0) C (0 to 100) C (100 to 260) C (260 to 300) C (300 to 400) C (400 to 600) C (600 to 630) C 0.12 C 0.12 C 0.22 C PtNi 385, 120 Ω (-80 to 0) C (0 to 100) C (100 to 260) C 0.16 C Cu 427, 10 Ω (-100 to 260) C 0.43 C Oscilloscopes Amplitude DC Signal 50 Ω Load 1 MΩ Load (-6.6 to 6.6) V (-130 to 130) V 0.19 % + 40 µv % + 40 µv Amplitude Square Wave 50 Ω Load 1 mv to 6.6 V p-p 10 Hz to 1 khz (1 to 10) khz 0.27 % + 32 µv 0.27 % + 32 µv 1 MΩ Load 1 mv to 130 V p-p 10 Hz to 1 khz (1 to 10) khz 0.12 % + 32 µv 0.27 % + 32 µv Leveled Sine Wave Flatness Relative to 50 khz 5 mv to 5.5 V: 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 1.5 % + 78 µv 1.9 % + 78 µv 3.4 % + 78 µv 5 mv to 3.5 V: (600 to 1100) MHz 4.3 % + 78 µv Time Marker into 50 Ω Load 5 s to 50 ms 4.2 ms/s (A2LA Cert. No ) 03/23/2016 Page 11 of 18

12 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments Oscilloscopes (cont) Time Marker into 50Ω Load 1 ns to 20 ms (cardinal points) 2.2 µs/s 1 ns to 20 ms (noncardinal points) 42 µs/s Edge Specs into 50 Ω Load Rise Time 350 ps 78 ps DC Power Generate 33 mv to 1020 V Output (0.33 to ) ma (0.33 to ) A (3 to 20.5) A % % % AC Power Generate (45 to 65) Hz PF=1 33 mv to 0.33 V (3.3 to 33) ma (33 to 330) ma (0.33 to 1.1) A (1.1 to 3) A (3 to 11) A (11 to 20.5) A % % % % % % (0.33 to 3.3) V (3.3 to 33) ma (33 to 330) ma (0.33 to 1.1) A (1.1 to 3) A (3 to 11) A (11 to 20.5) A % % % % % % (3.3 to 33) V (3.3 to 33) ma (33 to 330) ma (0.33 to 1.1) A (1.1 to 3) A (3 to 11) A (11 to 20.5) A % % % % % % (A2LA Cert. No ) 03/23/2016 Page 12 of 18

13 Parameter/Equipment Range CMC 2, 5, 6 ( ) Comments AC Power Generate (45 to 65) Hz PF=1 (cont) (33 to 330) V (3.3 to 33) ma (33 to 330) ma (0.33 to 1.1) A (1.1 to 3) A (3 to 11) A (11 to 20.5) A % % % % % % (330 to 1020) V (3.3 to 33) ma (33 to 330) ma (0.33 to 1.1) A (1.1 to 3) A (3 to 11) A (11 to 20.5) A % % % % % % Inductance khz / 1V Fixed Points 1 mh 10 mh 100 mh 1000 mh 10 H 0.26 µh 2.4 µh 24 µh 0.23 mh 2.4 mh GenRad Capacitance khz / 1V Fixed Points 10 pf 100 pf 1000 pf 10 nf 100 nf 1000 nf 10 µf 100 µf 47 nf 58 nf 0.24 pf 2.4 pf 23 pf 0.24 nf 2.4 nf 66 nf GenRad (A2LA Cert. No ) 03/23/2016 Page 13 of 18

14 Parameter/Range Frequency CMC 2, 5, 6 ( ) Comments Capacitance Generate (0.19 to 1.1) nf (1.1 to 3.3) nf (3.3 to 11) nf (11 to 110) nf (110 to 330) nf (0.33 to 1.1) µf (1.1 to 3.3) µf (3.3 to 11) µf (11 to 33) µf (33 to 110) µf (110 to 330) µf (0.33 to 1.1) mf (1.1 to 3.3) mf (3.3 to 11) mf (11 to 33) mf (33 to 110) mf 10 Hz to 10 khz 10 Hz to 3 khz 10 Hz to 1 khz 10 Hz to 1 khz 10 Hz to 1 khz (10 to 600) Hz (10 to 300) Hz (10 to 150) Hz (10 to 120) Hz (10 to 80) Hz (0 to 50) Hz (0 to 20) Hz (0 to 6) Hz (0 to 2) Hz (0 to 0.6) Hz (0 to 0.2) Hz 0.44 % nf 0.41 % nf 0.21 % nf 0.21 % nf 0.21 % nf 0.21 % + 1 nf 0.21 % + 3 nf 0.21 % + 10 nf 0.32 % + 30 nf 0.37 % nf 0.37 % nf 0.38 % + 1 µf 0.36 % + 3 µf 0.37 % + 10 µf 0.59 % + 30 µf 0.89 % µf III. Mechanical Parameter/Equipment Range CMC 2, 5 ( ) Comments Torque Tools 3 (5 to 50) in ozf (5 to 50) in lbf (40 to 400) in lbf (100 to 1000) in lbf (25 to 250) ft lbf (60 to 600) ft lbf 0.38 % 0.31 % 0.38 % 0.38 % 0.38 % 0.49 % CDI Suretest model 5000ST Torque Transducers, Fixed Points 220 in ozf 110 in lbf 275 ft lbf 2000 ft lbf 0.25 % IV 0.15 % IV % IV 0.027% IV 2.5 inch arm with Class F weights 5 inch arm with Class F weights 10 inch arm with Class F weights 40 inch arm with Class F weights (A2LA Cert. No ) 03/23/2016 Page 14 of 18

15 Parameter/Equipment Range CMC 2, 5 ( ) Comments Force (Load Cells) Tension and Compression Force Gauges 3 (20 to 500) lbf (500 to 1000) lbf (1000 to 5000) lbf (5000 to ) lbf ( to ) lbf ( to ) lbf ( to ) lbf 0.02 % 0.04 % 0.02 % 0.02 % 0.02 % 0.03 % 0.02 % Interface gold 1600 series load cells w/ GSSYS software Force Gages, Tension and Compression (0 to 10) lbf (10 to 50) lbf (50 to 100) lbf 8.6 g 8.9 g 10 g Class F weights Class 6 weights/hangers Pressure 3 (0 to 3) inh 2 O (3 to 30) inh 2 O (0 to 4.5) psi (4.5 to 15) psi (0 to 150) psia (150 to 500) psia inh 2 O % psi 0.012% psi 0.012% Fluke PPC4 Budenberg 480D (0.5 to 16) kpsi % DHI PG7202 (0.725 to 30) kpsi % psi Scales and Balances (1 to 10) mg (10 to 500) mg (1 to 50) g (50 to 300) g (300 to 500) g (0.5 to 1) kg (1 to 3) kg (3 to 5) kg mg 0.04 mg 0.29 mg 2.9 mg 2.9 mg 5.8 mg 17 mg 29 mg Class 2 weights (0.25 to 0.5) lb (0.5 to 10) lb (10 to 25) lb (25 to 50) lb (50 to 100) lb (100 to 500) lb lb lb lb lb lb lb Class F weights (A2LA Cert. No ) 03/23/2016 Page 15 of 18

16 IV. Thermodynamics Parameter/Equipment Range CMC 2 ( ) Comments Temperature Measuring (-20 to 250) C Equipment 3 (250 to 650) C C 0.60 C Hart 5626 SPRT w/ Hart 1560, 2560 module, baths, drywell Temperature (-20 to 250) C Thermocouple Probes 3 (250 to 650) C 0.54 C 0.80 C Hart 5626 SPRT w/ Hart 1560, 2560 module, baths, drywell Temperature RTD (-20 to 250) C Probes 3 (250 to 650) C C 0.59 C Hart 5626 SPRT w/ Hart 1560, Agilent 34970, baths, drywell Temperature Measure 3 (-196 to 660) C C Hart 5626 SPRT w/ Hart 1560, 2560 module Temperature System (400 to 1200) C 0.38 % Type R TC and Hart 2560 Accuracy Test 3 module Infrared Temperature (35 to 100) ºC Measuring Equipment 3 (100 to 200) ºC (200 to 350) ºC (350 to 500) ºC 0.66 ºC 0.96 ºC 1.7 ºC 2.1 ºC Fluke 4181 IR calibrator Relative Humidity Measuring Equipment 11 % RH 33 % RH 75 % RH 1.4 % RH 1.4 % RH 1.4 % RH VAISALA HMI41/HMP46 Relative Humidity Measure (5 to 90) % RH 1.4 % RH VAISALA HMI41/HMP46 (A2LA Cert. No ) 03/23/2016 Page 16 of 18

17 V. Time & Frequency Parameter/Equipment Range CMC 2 ( ) Comments Time Interval Totalize (1 to ) s s Agilent 53132A Method 3 Agilent 33250A w/ Fluke 910R Frequency Measuring Equipment 3 10 MHz DC to 80 MHz 5.6 phz/hz 13 phz/hz + 1 µhz Fluke 910R locked to GPS Agilent 33250A w/ Fluke 910R Frequency Measure 3 DC to 3 GHz 13 phz/hz + 1 µhz Agilent 53132A opt 10, 30 w/ Fluke 910R 1 This laboratory offers commercial calibration service and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer s site being larger than the CMC. 4 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches. 5 All CMCs listed in % are percent of reading of input unless otherwise stated. (A2LA Cert. No ) 03/23/2016 Page 17 of 18

18 6 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. (A2LA Cert. No ) 03/23/2016 Page 18 of 18

19 Accredited Laboratory A2LA has accredited TEKTRONIX INC. Tulsa, OK for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSLI Z and any additional program requirements in the field of calibration. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC- IAF Communiqué dated 8 January 2009). Presented this 23 rd day of March Senior Director of Quality and Communications For the Accreditation Council Certificate Number Valid to September 30, 2017 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.