Certificate of Accreditation

Transcription

1 PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Bldg#660 King Abdullah Road, Al Waha District, Riyadh, Saudi Arabia (Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard: ISO/IEC 17025:2005 This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communiqué dated April 2017): Acoustic, Chemical, Dimensional, Electrical, Mass, Force & Weighing Devices, Mechanical, Optical, Thermodynamic and Frequency (As detailed in the supplement) Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This Accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body s duty to observe and comply with the said rules. For PJLA: Initial Accreditation Date: Issue Date: Expiration Date: Tracy Szerszen President/Operations Manager Perry Johnson Laboratory Accreditation, Inc. (PJLA) 755 W. Big Beaver, Suite 1325 Troy, Michigan June 6, 2018 June 6, 2018 August 31, 2020 Accreditation No.: Certificate No.: L The validity of this certificate is maintained through ongoing assessments based on a continuous accreditation cycle. The validity of this certificate should be confirmed through the PJLA website: Page 1 of 11

2 Acoustic Certificate of Accreditation: Supplement AND Sound Level FO 94 db to 114 db 0.49 db Sound Level Calibrator CEM ; SC-05 Vibration Meters/Sensors- Acceleration F 80 Hz to 10 khz 1 m/s 2 2 % of Reading Vibration Calibrator MMF Germany ; VC110 As a Factor of Frequency Chemical AND ph FO 4 ph, 7 ph, and 0 ph 0.02 ph ph Standard Solutions Total Dissolved Solids Conductivity FO mg/l 5 mg/l TDS/Conductivity Solutions µs/cm 20 µs/cm Dimensional AND Caliper FO 1 mm to 100 mm ( L) nm Gauge Block 100 mm to 300 mm ( L) nm DIN 862, NPL40, NPL mm to 500 mm (0 + 4L) nm 500 mm to mm ( L) nm Micrometer FO 1 mm to 100 mm ( L) nm Gauge Block 100 mm to 300 mm ( L) nm BS 959, BS 6468, NPL40, NPL mm to 500 mm (0 + 4L) nm 500 mm to mm ( L) nm Feeler Gauge FO Up to 1 mm 0.59 µm Micrometer BS 957 Dial Gauge FO Up to 25 mm 0.59 µm Micrometer BS EN ISO 463, JIS B7503 Dial Test Indicator FO Up to 25 mm 0.59 µm Micrometer BS EN ISO 9493, JIS B7533 Angle Measuring 15 to 90 1 arc/sec Angle Block Equipment FO Angular Level and Total Stations F Up to Digital Level/Protractor Issue: 06/2018 This supplement is in conjunction with certificate #L Page 2 of 11

3 Dimensional AND Sieve FO 50X to 600X Magnification 0.1 µm Digital Microscope / Glass Scale; INSIZE ISM- PM600 and PM200 ASTM E11 Nuclear Gauge-Moisture FO 1.12 kg/l to 2.72 kg/l 0.03 kg/l Granite/Limestone Stone Nuclear Gauge-Density FO 0 kg/l to 0.72 kg/l 0.04 kg/l Electrical Equipment to Output AC Voltage (at the listed frequencies) F 20 Hz to 45 Hz 1 mv to 200 mv mv 45 Hz to 1 khz 1 mv to 200 mv mv 1 khz to 20 khz 1 mv to 200 mv mv 20 Hz to 45 Hz 0.2 V to 2 V mv 45 Hz to 1 khz 0.2 V to 2 V mv 1 khz to 20 khz 0.2 V to 2 V mv 20 Hz to 45 Hz 2 V to 20 V 0.36 mv 45 Hz to 1 khz 2 V to 20 V 0.36 mv 1 khz to 20 khz 2 V to 20 V 0.36 mv 40 Hz to 1 khz 20 V to 200 V 4.1 mv 40 Hz to 1 khz 200 V to V 18 mv Equipment to Output DC Voltage F for load of < 1MΩ -220 mv to 200 mv mv for load of < 1MΩ 0.2 V to 2 V 0.01 mv for load of < 1MΩ 2 V to 20 V 0.13 mv for load of < 1MΩ 20 V to 200 V 1.9 mv for load of < 1 MΩ 200 V to V 5.5 mv AND Multi-Function Calibrator TIME Electronics; 5025E Issue: 06/2018 This supplement is in conjunction with certificate #L Page 3 of 11

4 Electrical Equipment to Output AC Current (at the listed frequencies) F 20 Hz to 1 khz 20 µa to 200µA 0.11 µa 20 Hz to 1 khz 0.2 ma to 2 ma 0.77 µa 20 Hz to 1 khz 2 ma to 20 ma ma 20 Hz to 1 khz 20 ma to 200 ma ma 20 Hz to 500 Hz 0.2 A to 2 A 1.4 ma 20 Hz to 500 Hz 2A to 22 A 17 ma Equipment to Output AC Current with COIL Adaptor (at the listed frequencies) F 20 Hz to 500 Hz 22 A to A ma Equipment to Output DC Current F Equipment to Output DC Current with COIL Adaptor F Equipment to Output Resistance Decade Resistance F Equipment to Output Resistance Simulated Resistance F Equipment to Output Capacitance Fixed Capacitance F -200 µa to 200 µa µa 0.2 ma to 2 ma 0.04 µa 2 ma to 20 ma 0.42 µa 20 ma to 200 ma ma 0.2 A to 2 A 0.86 ma 2 A to 22 A 7.7 ma 22 A to A ma AND Multi-Function Calibrator Time Electronics; 5025E, 50X Current Coil Adaptor 10 Ω 0.49 mω Multi-Function Calibrator 100 Ω 2.3 mω TIME Electronics; 5025E 1 kω 7 mω 10 kω Ω 100 kω 3.9 Ω 1 MΩ 0.39 kω 10 MΩ 0.14 kω 100 MΩ 130 kω 1 GΩ 6.7 MΩ 40 Ω to 400 Ω 4.9 mω 400 Ω to 4 kω 68 mω 4 kω to 40 kω 0.55 Ω 10 nf 0.01 nf 20 nf 0.02 nf 50 nf 0.05 nf Issue: 06/2018 This supplement is in conjunction with certificate #L Page 4 of 11

5 Electrical Equipment to Output Capacitance Fixed Capacitance F Equipment to Output Digital Frequency F Square Wave Output 2V pk-pk Equipment to Output Amplitude(Oscilloscope) F AND 100 nf 0.1 nf Multi-Function Calibrator 1 µf 1 nf TIME Electronics; 5025E 0.1 Hz to 1 khz Hz 1 khz to 1 MHz 0.01 Hz 1 MHz to 10 MHz 0.02 Hz 1 khz Sq Wave 2 mv to 200 mv mv 1 khz Sq Wave 0.2 V to 20 V 0.06 mv 1 khz Sq Wave 20 V to 200 V 0.59 mv 1 khz Sq Wave 50 Ω 1 mv to 200 mv mv 1 khz Sq Wave 50 Ω 0.2 V to 2 V 0.06 mv Equipment to Output Frequency (Oscilloscope) F 1.5 Vpk-pk 0.1 Hz to 100 khz 0.02 Hz 1 Vpk-pk Sinusoidal 20 MHz to 100 MHz 12 Hz Multi-Function Calibrator TIME Electronics; 5025E (Oscilloscope Option) Equipment to Output DC 1V to 22 V 0.29 mv Multi-Function Calibrator Voltage F 22 V to 220 V 0.03 V TIME Electronics; 5025E (Power Option) 220 V to 1050 V 0.13 V Equipment to Output DC Current F 0.2 A to 2.2A 1.3 ma 2.2A to 22 A 7.7 ma Equipment to Output AC Voltage (Power Factor- Up to 1.00) (at the listed frequencies) F 45 Hz to 400 Hz 1V to 22 V 1.0 mv 45 Hz to 400 Hz 22 V to 220 V 14 mv 45 Hz to 400 Hz 220 V to V 0.05 V Equipment to Output AC Current (Power Factor- Up to 1.00) (at the listed frequencies) F 45 Hz to 400 Hz 0.2 A to 2.2 A 3.7 ma 45 Hz to 400 Hz 2.2 A to 22 A 17 ma Equipment to Measure DC Voltage FO Equipment to Measure DC Current FO -75 mv to -75 mv 0.84 µv Multi-Function Process -30 V to 30 V 0.59 µv Calibrator Additel; ADT223A -30 ma to 30 ma µa Issue: 06/2018 This supplement is in conjunction with certificate #L Page 5 of 11

6 Electrical Equipment to Measure Resistance: 2-Wire FO Equipment to Measure Resistance: 3-Wire FO Equipment to Measure Resistance: 4-Wire FO Equipment to Measure Frequency FO Temperature Simulation- Type K FO AND 0 Ω to 400 Ω 6.06 x 10-3 Ω Multi-Function Process 400 Ω to 4 kω 3.50 x 10-2 Ω Calibrator Additel; ADT223A 0 Ω to 400 Ω 6.06 x 10-3 Ω 400 Ω to 4 kω 3.50 x 10-2 Ω 0 Ω to 400 Ω 6.06 x 10-3 Ω 400 Ω to 4 kω 3.50 x 10-2 Ω 1 Hz to 50 khz 0.59 Hz -200 C to 0 C C Multi-Function Process 0 C to C C Calibrators Additel ADT223A OIML R133, ASTM E77, Euramet cg-11, DKD R5-1, ITS90, Euramet cg-8 Mass, Force, and Weighing Devices Weighing Instruments- Analytical Balances F Weighing Instruments- Precision Balances F Weighing Instruments- Electronic Balances/Scales F Test Weights OIML Class F2 F (tolerances are larger) AND 2 mg to 200 g (6 x x 10-4 Wt) mg Std. Weights Class E2 OIML R76-1, Euramet cg g to 1 kg (-8 x x 10-4 Wt) mg 1 kg to 20 kg ( x 10-1 Wt) mg Std. Weights Class F1 OIML R76-1, Euramet cg kg to kg (-1.13 x x 10-2 Wt) g Std. Weights Class M1 OIML R76-1, Euramet cg-18 2 mg mg 5 mg mg 10 mg mg 20 mg mg 50 mg mg 100 mg mg 200 mg mg 500 mg mg 1 g mg 2 g mg 5 g mg Issue: 06/2018 This supplement is in conjunction with certificate #L Page 6 of 11

7 Mass, Force, and Weighing Devices Test Weights OIML Class F2 F (tolerances are larger) AND 10 g mg Std. Weights Class E2, 20 g mg Double-Substitution with Air Bouyancy Correction 50 g mg OIML R111-1, M g mg UKAS 200 g 0.06 mg 500 g 5.8 mg 1 kg 5.8 mg 2 kg 5.9 mg 5 kg 6.5 mg 10 kg 58 mg 20 kg 59 mg Batching Plant F 1g to g (5.22 x x 10-3 Wt) mg Standard Weights Class F1, ASTM C94 1 kg to 500 kg (-5.03 x x 10-2 Wt) g Standard Weights Class 500 kg to kg (-4.50 x x 10-2 Wt) g M1,ASTM C94 Ignition Furnace - Balance FO Up to 10 kg ( x 10-1 Wt) mg Standard Weights Class F1 and M1 [1g~10kg] ASTM D kg/l to 2.72 kg/l 0.03 kg/l Granite/Limestone Stone Nuclear Gauges- Moisture FO Nuclear Gauges- 0 kg/l to 0.72 kg/l 0.04 kg/l Granite/Limestone Stone Density FO Force and Proving Ring F 10 kn to kn % of Reading Load Cell ASTM E4,ASTM E74, Euramet cg-4 Mechanical AND Torque FO 1.25 Nm to Nm Nm Torque Transducer Pressure Gauges (Vacuum and Compound) FO Up to psi 0.84 psi Digital Pressure Gauges ADDITEL 681 Series BS EN 837-1, DKD-R6-1, Euramet cg-17 Issue: 06/2018 This supplement is in conjunction with certificate #L Page 7 of 11

8 Mechanical Pressure Gauges (Vacuum and Compound) FO AND Up to psi 0.82 psi Digital Pressure Gauges Up to psi 0.8 psi ADDITEL 681 Series BS EN 837-1, DKD-R6-1, Up to psi 0.26 psi Euramet cg-17 Up to 290 psi Up to 100 psi 0.09 psi 0.05 psi psi to 15 psi psi Digital Vacuum Gauges ADDITEL 681 Series BS EN 837-1, DKD-R6-1 Euramet cg-17 Density Hydrometer F 1 g/cm 3 to 10 g/cm g/cm 3 Analytical Balance- ADAM PW254 NIST SP250,ASTM E100 Pipettes/Burettes Volumetric Gravimetric F Graduated Cylinders Volumetric Gravimetric F 1 ml to 200 ml ml Analytical Balance- ADAM PW254 Euramet cg-19, NISTIR 7383, NPL ml to ml ml Precision Balance- ADAM PGW6002E Euramet cg-19, NISTIR 7383, NPL ml to 200 ml ml Analytical Balance- ADAM PW254 Euramet cg-21nistir 7383, NPL ml to ml ml Precision Balance- ADAM PGW6002E Euramet cg-21, NISTIR 7383, NPL 2.2 Scmidth Hammer-Hardness FO 80 N/mm 2 2 N/mm 2 Standard Test Anvil NDT James Instruments, W- C-7312 Issue: 06/2018 This supplement is in conjunction with certificate #L Page 8 of 11

9 Optical AND Illuminance F Up to lux 0.16 lux Light Meter EXTECH EA31 Thermodynamic AND Temperature Measure FO -17 C to 140 C 0.24 C Temp Block Calibrators AMETEK, CTC-140A [-20 C to 140 C] OIML R133, ASTM E77, Euramet cg-11, DKD R5-1, ITS90, 50 C to 650 C 0.24 C Temp Block Calibrators AMETEK, CTC-650A [25 C to 650 C] OIML R133, ASTM E77, DKD R5-1, ITS90 Infrared Thermometer FO 25 C to 400 C 0.59 C Temp IR Calibrators JOFRA; ETC-400R OIML R133, ASTM E77, Euramet cg-11, DKD R5-1, ITS90, Euramet cg-8 Temperature Block Calibrators FO -17 C to 650 C 0.12 C Multi-Function Process Calibrators Additel ADT223A PRT Sensors [-20 C to 650 C] Euramet cg-13 Ignition Furnace Temperature FO -200 C to C C Multi-Function Process Calibrators [-200 C to C] ASTM D6307 Issue: 06/2018 This supplement is in conjunction with certificate #L Page 9 of 11

10 Time & Frequency Certificate of Accreditation: Supplement DEVICE SIZE AS AND Rate of Rotation F 6 rpm to 600 rpm 0.05 rpm Multi-Function Calibrator 600 rpm to rpm 0.07 rpm Time Electronics 5025E, Time Electronics Tacho rpm to rpm 0.13 rpm Adaptor rpm to rpm 0.58 rpm (As a factor of Frequency) 1. The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represents the smallest measurement uncertainty attainable by the laboratory when performing a more or less routine calibration of a nearly ideal device under nearly ideal conditions. It is typically expressed at a confidence level of 95 % using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for the same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree. 2. The laboratories range of calibration capability for all disciplines for which they are accredited is the interval from the smallest calibrated standard to the largest calibrated standard used in performing the calibration. The low end of this range must be an attainable value for which the laboratory has or has access to the standard referenced. Verification of an indicated value of zero in the absence of a standard is common practice in the procedure for many calibrations but by its definition it does not constitute calibration of zero capacity. 3. The presence of a superscript F means that the laboratory performs calibration of the indicated parameter at its fixed location. Example: Outside Micrometer F would mean that the laboratory performs this calibration at its fixed location. 4. The presence of a superscript O means that the laboratory performs calibration of the indicated parameter onsite at customer locations. Example: Outside Micrometer O would mean that the laboratory performs this calibration onsite at the customer s location. 5. The presence of a superscript FO means that the laboratory performs calibration of the indicated parameter both at its fixed location and onsite at customer locations. Example: Outside Micrometer FO would mean that the laboratory performs this calibration at its fixed location and onsite at customer locations. 6. Measurement uncertainties obtained for calibrations performed at customer sites can be expected to be larger than the measurement uncertainties obtained at the laboratories fixed location for similar calibrations. This is due to the effects of transportation of the standards and equipment and upon environmental conditions at the customer site which are typically not controlled as closely as at the laboratories fixed location. 7. The term L represents length in inches or millimeters as appropriate to the uncertainty statement. Issue: 06/2018 This supplement is in conjunction with certificate #L Page 10 of 11

11 8. The term Wt represents weight in pounds or grams (including SI multiple and submultiple units) appropriate to the uncertainty statement. 9. The term X proceeded by a number represents the number of times a lense system magnifies an image relative to its actual size. CMC stated as % of magnification represents the CMC of magnification expressed as a percentage of the total magnification. Issue: 06/2018 This supplement is in conjunction with certificate #L Page 11 of 11