DESCRIPTIO FEATURES TYPICAL APPLICATIO. LTC Channel Differential Input 24-Bit No Latency Σ ADC APPLICATIO S

Transcription

1 -Channel Differential Input -Bit No Latency Σ ADC FEATURES -Channel Differential Input with Automatic Channel Selection (Ping-Pong) Low Supply Current: µa, µa in Autosleep Differential Input and Differential Reference with GND to V CC Common Mode Range ppm INL, No Missing Codes.5ppm Full-Scale Error and.ppm Offset.ppm Noise,.5 Effective Number of Bits No Latency: Digital Filter Settles in a Single Cycle and Each Channel Conversion is Accurate Internal Oscillator No External Components Required db Min, 5Hz or Hz Notch Filter Narrow SSOP- Package Single Supply.7V to 5.5V Operation APPLIC S U Direct Sensor Digitizer Weight Scales Direct Temperature Measurement Gas Analyzers Strain-Gage Transducers Instrumentation Data Acquisition Industrial Process Control -Digit DVMs DESCRIPTIO U The LTC is a -channel differential input micropower -bit No Latency Σ TM analog-to-digital converter with an integrated oscillator. It provides ppm INL and.ppm RMS noise over the entire supply range. The two differential channels are converted alternately with channel ID included in the conversion results. It uses delta-sigma technology and provides single conversion settling of the digital filter. Through a single pin, the LTC can be configured for better than db input differential mode rejection at 5Hz or Hz ±%, or it can be driven by an external oscillator for a user defined rejection frequency. The internal oscillator requires no external frequency setting components. The converter accepts any external differential reference voltage from.v to V CC for flexible ratiometric and remote sensing measurement configurations. The fullscale differential input range is from.5v REF to.5v REF. The reference common mode voltage, V REFCM, and the input common mode voltage, V INCM, may be independently set anywhere within the GND to V CC. The DC common mode input rejection is better than db. The LTC communicates through a flexible 3-wire digital interface which is compatible with SPI and MICROWIRE TM protocols., LTC and LT are registered trademarks of Linear Technology Corporation. No Latency Σ is a trademark of Linear Technology Corporation. MICROWIRE is a trademark of National Semiconductor Corporation. TYPICAL APPLIC.7V TO 5.5V U.5 Total Unadjusted Error vs Input THERMOCOUPLE µf V CC F O REF + CH + LTC 5 CH SCK 3 3 REF CH + CS 7 CH 8, 9,, 5, GND TA V CC = INTERNAL OSC/5Hz REJECTION = EXTERNAL CLOCK SOURCE = INTERNAL OSC/Hz REJECTION 3-WIRE SPI INTERFACE TUE (ppm OF V REF )..5.5 T A = 9 C. V REF = 5V V INCM =.5V T A = 5 C V IN (V) TA

2 ABSOLUTE AXI U RATI GS W W W (Notes, ) Supply Voltage (V CC ) to GND....3V to 7V Analog Input Voltage to GND....3V to (V CC +.3V) Reference Input Voltage to GND....3V to (V CC +.3V) Digital Input Voltage to GND....3V to (V CC +.3V) Digital Output Voltage to GND....3V to (V CC +.3V) Operating Temperature Range LTCC... C to 7 C LTCI... C to 85 C Storage Temperature Range... 5 C to 5 C Lead Temperature (Soldering, sec)... 3 C U U U W PACKAGE/ORDER I FOR V CC REF + REF CH + CH CH + CH GND TOP VIEW GN PACKAGE -LEAD PLASTIC SSOP T JMAX = 5 C, θ JA = C/W GND GND F O SCK CS GND GND ORDER PART NUMBER LTCCGN LTCIGN GN PART MARKING I Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Notes 3, ) PARAMETER CONDITIONS MIN TYP MAX UNITS Resolution (No Missing Codes).V V REF V CC,.5 V REF V IN.5 V REF, (Note 5) Bits Integral Nonlinearity 5V V CC 5.5V, REF + =.5V,, V INCM =.5V, (Note ) ppm of V REF 5V V CC 5.5V,,, V INCM =.5V, (Note ) ppm of V REF REF + =.5V,, V INCM =.5V, (Note ) 5 ppm of V REF Offset Error.5V REF + V CC,,.5.5 µv GND IN + = IN V CC, (Note ) Offset Error Drift.5V REF + V CC,, nv/ C GND IN + = IN V CC Positive Full-Scale Error.5V REF + V CC,,.5 ppm of V REF IN + =.75REF +, IN =.5 REF + Positive Full-Scale Error Drift.5V REF + V CC,,.3 ppm of V REF / C IN + =.75REF +, IN =.5 REF + Negative Full-Scale Error.5V REF + V CC,,.5 ppm of V REF IN + =.5 REF +, IN =.75 REF + Negative Full-Scale Error Drift.5V REF + V CC,,.3 ppm of V REF / C IN + =.5 REF +, IN =.75 REF + Total Unadjusted Error 5V V CC 5.5V, REF + =.5V,, V INCM =.5V 3 ppm of V REF 5V V CC 5.5V,,, V INCM =.5V 3 ppm of V REF REF + =.5V,, V INCM =.5V, (Note ) ppm of V REF Output Noise 5V V CC 5.5V,,,.8 µv RMS GND IN = IN + V CC, (Note 3)

3 CO VERTER CHARACTERISTICS U The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Notes 3, ) LTC PARAMETER CONDITIONS MIN TYP MAX UNITS Input Common Mode Rejection DC.5V REF + V CC,, 3 db GND IN = IN + V CC (Note 5) Input Common Mode Rejection.5V REF + V CC,, db Hz ±% GND IN = IN + V CC, (Notes 5, 7) Input Common Mode Rejection.5V REF + V CC,, db 5Hz ±% GND IN = IN + V CC, (Notes 5, 8) Input Normal Mode Rejection (Notes 5, 7) db Hz ±% Input Normal Mode Rejection (Note 5, 8) db 5Hz ±% Reference Common Mode.5V REF + V CC, GND REF.5V, 3 db Rejection DC V REF =.5V, IN = IN + = GND (Note 5) Power Supply Rejection, DC REF + =.5V,, IN = IN + = GND db Power Supply Rejection, Hz ±% REF + =.5V,, IN = IN + = GND, (Note 7) db Power Supply Rejection, 5Hz ±% REF + =.5V,, IN = IN + = GND, (Note 8) db U U U U A ALOG I PUT A D REFERE CE The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS IN + Absolute/Common Mode IN + Voltage GND.3 V CC +.3 V IN Absolute/Common Mode IN Voltage GND.3 V CC +.3 V V IN Input Differential Voltage Range V REF / V REF / V (IN + IN ) REF + Absolute/Common Mode REF + Voltage. V CC V REF Absolute/Common Mode REF Voltage GND V CC. V V REF Reference Differential Voltage Range. V CC V (REF + REF ) C S (IN + ) IN + Sampling Capacitance 8 pf C S (IN ) IN Sampling Capacitance 8 pf C S (REF + ) REF + Sampling Capacitance 8 pf C S (REF ) REF Sampling Capacitance 8 pf I DC_LEAK (IN + ) IN + DC Leakage Current CS = V CC = 5.5V, IN + = GND na I DC_LEAK (IN ) IN DC Leakage Current CS = V CC = 5.5V, IN = 5.5V na I DC_LEAK (REF + ) REF + DC Leakage Current CS = V CC = 5.5V, REF + = 5.5V na I DC_LEAK (REF ) REF DC Leakage Current CS = V CC = 5.5V, na 3

4 DIGITAL I PUTS A D DIGITAL OUTPUTS U U The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS V IH High Level Input Voltage.7V V CC 5.5V.5 V CS, F O.7V V CC 3.3V. V V IL Low Level Input Voltage.5V V CC 5.5V.8 V CS, F O.7V V CC 5.5V. V V IH High Level Input Voltage.7V V CC 5.5V (Note 9).5 V SCK.7V V CC 3.3V (Note 9). V V IL Low Level Input Voltage.5V V CC 5.5V (Note 9).8 V SCK.7V V CC 5.5V (Note 9). V I IN Digital Input Current V V IN V CC µa CS, F O I IN Digital Input Current V V IN V CC (Note 9) µa SCK C IN Digital Input Capacitance pf CS, F O C IN Digital Input Capacitance (Note 9) pf SCK V OH High Level Output Voltage I O = 8µA V CC.5 V V OL Low Level Output Voltage I O =.ma. V V OH High Level Output Voltage I O = 8µA (Note ) V CC.5 V SCK V OL Low Level Output Voltage I O =.ma (Note ). V SCK I OZ Hi-Z Output Leakage µa POWER REQUIRE E TS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS V CC Supply Voltage V I CC W U Supply Current Conversion Mode CS = V 3 µa Sleep Mode CS = V CC (Note ) 3 µa Sleep Mode CS = V CC,.7V V CC 3.3V µa (Note )

5 TI I G CHARACTERISTICS U W LTC The denotes specifications which apply over the full operating temperature range, otherwise specifications are at. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS f EOSC External Oscillator Frequency Range.5 khz t HEO External Oscillator High Period.5 39 µs t LEO External Oscillator Low Period.5 39 µs t CONV Conversion Time F O = V ms F O = V CC ms External Oscillator (Note ) 5/f EOSC (in khz) ms f ISCK Internal SCK Frequency Internal Oscillator (Note ) 9. khz External Oscillator (Notes, ) f EOSC /8 khz D ISCK Internal SCK Duty Cycle (Note ) 5 55 % f ESCK External SCK Frequency Range (Note 9) khz t LESCK External SCK Low Period (Note 9) 5 ns t HESCK External SCK High Period (Note 9) 5 ns t DOUT_ISCK Internal SCK 3-Bit Data Output Time Internal Oscillator (Notes, )..7.7 ms External Oscillator (Notes, ) 5/f EOSC (in khz) ms t DOUT_ESCK External SCK 3-Bit Data Output Time (Note 9) 3/f ESCK (in khz) ms t CS to Low Z ns t CS to High Z ns t3 CS to SCK (Note ) ns t CS to SCK (Note 9) 5 ns t KQMAX SCK to Valid ns t KQMIN Hold After SCK (Note 5) 5 ns t 5 SCK Set-Up Before CS 5 ns t SCK Hold After CS 5 ns Note : Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note : All voltage values are with respect to GND. Note 3: V CC =.7V to 5.5V unless otherwise specified. V REF = REF + REF, V REFCM = (REF + + REF )/; V IN = IN + IN, V INCM = (IN + + IN )/, IN + and IN are defined as the selected positive (CH + or CH + ) and negative (CH or CH ) input respectively. Note : F O pin tied to GND or to V CC or to external conversion clock source with f EOSC = 53Hz unless otherwise specified. Note 5: Guaranteed by design, not subject to test. Note : Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 7: F O = V (internal oscillator) or f EOSC = 53Hz ±% (external oscillator). Note 8: F O = V CC (internal oscillator) or f EOSC = 8Hz ±% (external oscillator). Note 9: The converter is in external SCK mode of operation such that the SCK pin is used as digital input. The frequency of the clock signal driving SCK during the data output is f ESCK and is expressed in khz. Note : The converter is in internal SCK mode of operation such that the SCK pin is used as digital output. In this mode of operation the SCK pin has a total equivalent load capacitance C LOAD = pf. Note : The external oscillator is connected to the F O pin. The external oscillator frequency, f EOSC, is expressed in khz. Note : The converter uses the internal oscillator. F O = V or F O = V CC. Note 3: The output noise includes the contribution of the internal calibration operations. Note : Guaranteed by design and test correlation. 5

6 TYPICAL PERFOR A CE CHARACTERISTICS TUE (ppm OF V REF ).5..5 Total Unadjusted Error vs Temperature (, V REF = 5V) U W.5 T A = 9 C. V REF = 5V V INCM =.5V T A = 5 C V IN (V) TUE (ppm OF V REF ) Total Unadjusted Error vs Temperature (, V REF =.5V) T A = 9 C T A = 5 C REF + =.5V V REF =.5V V INCM =.5V.5.5 V IN (V) TUE (ppm OF V REF ) 8 8 Total Unadjusted Error vs Temperature (V CC =.7V, V REF =.5V) V CC =.7V REF + =.5V V REF =.5V V INCM =.5V T A = 9 C T A = 5 C.5.5 V IN (V) G G G3 Integral Nonlinearity vs Temperature (, V REF = 5V) Integral Nonlinearity vs Temperature (, V REF =.5V) Integral Nonlinearity vs Temperature (V CC =.7V, V REF =.5V) INL ERROR (ppm OF V REF ) V REF = 5V V INCM =.5V T A = 5 C T A = 9 C V IN (V) INL ERROR (ppm OF V REF ) REF + =.5V V REF =.5V V INCM =.5V T A = 5 C T A = 9 C.5.5 V IN (V) INL ERROR (ppm OF V REF ) 8 8 V CC =.7V REF + =.5V V REF =.5V V INCM =.5V T A = 9 C T A = 5 C.5.5 V IN (V) G G5 G Noise Histogram (Output Rate = 7.5Hz,, V REF = 5V) Noise Histogram (Output Rate =.5Hz,, V REF = 5V) Noise Histogram (Output Rate = 5.5Hz,, V REF = 5V) NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF = 5V V IN = V IN + =.5V IN =.5V GAUSSIAN DISTRIBUTION m =.5ppm σ =.53ppm NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF = 5V V IN = V IN + =.5V IN =.5V F O = 8Hz GAUSSIAN DISTRIBUTION m =.7ppm σ =.5ppm NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF = 5V V IN = V IN + =.5V IN =.5V F O = 75Hz GAUSSIAN DISTRIBUTION m = 8.85ppm σ =.3ppm OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) G7 G8 G9

7 TYPICAL PERFOR A CE CHARACTERISTICS U W Noise Histogram (Output Rate = 7.5Hz,, V REF =.5V) Noise Histogram (Output Rate =.5Hz,, V REF =.5V) Noise Histogram (Output Rate = 5.5Hz,, V REF =.5V) NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V GAUSSIAN DISTRIBUTION m =.33ppm σ =.93ppm NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V F O = 8Hz GAUSSIAN DISTRIBUTION m =.ppm σ =.9ppm NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V F O = 75Hz GAUSSIAN DISTRIBUTION m = 3.85ppm σ =.3ppm OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) G G G Noise Histogram (Output Rate = 7.5Hz, V CC =.7V, V REF =.5V) Noise Histogram (Output Rate =.5Hz, V CC =.7V, V REF =.5V) Noise Histogram (Output Rate = 5.5Hz, V CC =.7V, V REF =.5V) NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V CC =.7V V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V GAUSSIAN DISTRIBUTION m =.79ppm σ =.98ppm NUMBER OF READINGS (%) 8, CONSECUTIVE READINGS V CC =.7V V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V F O = 8Hz GAUSSIAN DISTRIBUTION m =.77ppm σ =.97ppm NUMBER OF READINGS (%) , CONSECUTIVE READINGS V CC =.7V V REF =.5V V IN = V REF + =.5V IN + =.5V IN =.5V F O = 75Hz GAUSSIAN DISTRIBUTION m = 3.7ppm σ =.95ppm OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) OUTPUT CODE (ppm OF V REF ) G3 G G5 Long-Term Noise Histogram (Time = Hrs,, V REF = 5V) Consecutive ADC Readings vs Time RMS Noise vs Input Differential Voltage NUMBER OF READINGS (%) 8 GAUSSIAN DISTRIBUTION m =.837ppm σ =.555ppm ADC CONSECUTIVE READINGS V REF = 5V V IN = V IN + =.5V IN =.5V OUTPUT CODE (ppm OF V REF ) ADC READING (ppm OF V REF ) V REF = 5V V IN = V REF + IN + =.5V = 5V REF IN =.5V = GND TIME (HOURS) RMS NOISE (ppm OF V REF ) V REF = 5V V INCM =.5V INPUT DIFFERENTIAL VOLTAGE (V) G G7 G8 7

8 TYPICAL PERFOR A CE CHARACTERISTICS U W RMS Noise vs V INCM RMS Noise vs Temperature (T A ) RMS Noise vs V CC RMS NOISE (nv) V REF = 5V IN + = V INCM 7 IN = V INCM V IN = V V INCM (V) RMS NOISE (nv) IN + =.5V IN =.5V 75 V IN = V TEMPERATURE ( C) RMS NOISE (nv) REF + =.5V V REF =.5V IN + = GND IN = GND V CC (V) G9 G G RMS Noise vs V REF Offset Error vs V INCM Offset Error vs Temperature (T A ) RMS NOISE (nv) IN + = GND IN = GND V REF (V) OFFSET ERROR (ppm OF V REF ).3... V REF = 5V IN + = V INCM IN = V INCM. V IN = V V INCM (V) OFFSET ERROR (ppm OF V REF ).3... IN + =.5V. IN =.5V V IN = V TEMPERATURE ( C) G G3 G Offset Error vs V CC Offset Error vs V REF +Full-Scale Error vs Temperature (T A ) OFFSET ERROR (ppm OF V REF ).. REF + =.5V. V REF =.5V IN + = GND. IN = GND V CC (V) OFFSET ERROR (ppm OF V REF ).. V. CC = 5V IN + = GND. IN = GND V REF (V) +FULL-SCALE ERROR (ppm OF V REF ) IN + =.5V IN = GND TEMPERATURE ( C) G5 G G7 8

9 TYPICAL PERFOR A CE CHARACTERISTICS U W +Full-Scale Error vs V CC +Full-Scale Error vs V REF Full-Scale Error vs Temperature (T A ) +FULL-SCALE ERROR (ppm OF V REF ) 3 REF + =.5V V REF =.5V IN + =.5V IN = GND V CC (V) +FULL-SCALE ERROR (ppm OF V REF ) 3 REF + = V REF IN + =.5 REF + IN = GND V REF (V) FULL-SCALE ERROR (ppm OF V REF ) 3 IN + = GND IN =.5V TEMPERATURE ( C) G8 G9 G3 Full-Scale Error vs V CC Full-Scale Error vs V REF PSRR vs Frequency at V CC FULL-SCALE ERROR (ppm OF V REF ) 3 REF + =.5V V REF =.5V IN + = GND IN =.5V FULL-SCALE ERROR (ppm OF V REF ) 3 REF + = V REF IN + = GND IN =.5 REF + REJECTION (db) 8 V CC =.V DC ±.V REF + =.5V IN + = GND IN = GND V CC (V) G V REF (V) G3.. FREQUENCY AT V CC (Hz) G33 PSRR vs Frequency at V CC PSRR vs Frequency at V CC PSRR vs Frequency at V CC REJECTION (db) 8 V CC =.V DC REF + =.5V IN + = GND IN = GND REJECTION (db) 8 V CC =.V DC ±.V REF + =.5V IN + = GND IN = GND REJECTION (db) 8 V CC =.V DC ±.7V P-P REF + =.5V IN + = GND IN = GND k k k M FREQUENCY AT V CC (Hz) FREQUENCY AT V CC (Hz) FREQUENCY AT V CC (Hz) G3 G35 G3 9

10 TYPICAL PERFOR A CE CHARACTERISTICS U W Conversion Current vs Temperature Conversion Current vs Output Data Rate Sleep Mode Current vs Temperature CONVERSION CURRENT (µa) 3 V CC = 5.5V 9 8 CS = GND SCK = NC = NC V CC = 3V 7 V CC =.7V TEMPERATURE ( C) SUPPLY CURRENT (µa) V REF = V CC IN + = GND IN = GND SCK = NC = NC CS = GND F O = EXT OSC V CC = 3V OUTPUT DATA RATE (READINGS/SEC) SLEEP MODE CURRENT (µa) V CC = 5.5V V CC = 3V V CC =.7V CS = V CC SCK = NC = NC TEMPERATURE ( C) G37 G38 G39 PI FU CTIO S U U U V CC (Pin ): Positive Supply Voltage. Bypass to GND with a µf tantalum capacitor in parallel with.µf ceramic capacitor as close to the part as possible. REF + (Pin ), REF (Pin 3): Differential Reference Input. The voltage on these pins can have any value between GND and V CC as long as the reference positive input, REF +, is maintained more positive than the reference negative input, REF, by at least.v. CH + (Pin ): Positive Input for Differential Channel. CH (Pin 5): Negative Input for Differential Channel. CH + (Pin ): Positive Input for Differential Channel. CH (Pin 7): Negative Input for Differential Channel. The voltage on these four analog inputs (Pins to 7) can have any value between GND and V CC. Within these limits the converter bipolar input range (V IN = IN + IN ) extends from.5 (V REF ) to.5 (V REF ). Outside this input range the converter produces unique overrange and underrange output codes. GND (Pins 8, 9,, 5, ): Ground. Multiple ground pins internally connected for optimum ground current flow and V CC decoupling. Connect each one of these pins to a ground plane through a low impedance connection. All five pins must be connected to ground for proper operation. CS (Pin ): Active LOW Digital Input. A LOW on this pin enables the digital output and wakes up the ADC. Following each conversion the ADC automatically enters the Sleep mode and remains in this low power state as long as CS is HIGH. A LOW-to-HIGH transition on CS during the Data Output transfer aborts the data transfer and starts a new conversion. (Pin ): Three-State Digital Output. During the Data Output period, this pin is used as serial data output. When the chip select CS is HIGH (CS = V CC ) the pin is in a high impedance state. During the Conversion and Sleep periods, this pin is used as the conversion status output. The conversion status can be observed by pulling CS LOW. SCK (Pin 3): Bidirectional Digital Clock Pin. In Internal Serial Clock Operation mode, SCK is used as digital output for the internal serial interface clock during the Data Output period. In External Serial Clock Operation mode, SCK is used as digital input for the external serial interface clock during the Data Output period. A weak internal pullup is automatically activated in Internal Serial Clock Operation mode. The Serial Clock Operation mode is determined by the logic level applied to the SCK pin at power up or during the most recent falling edge of CS.

11 PI FU CTIO S U U U F O (Pin ): Frequency Control Pin. Digital input that controls the ADC s notch frequencies and conversion time. When the F O pin is connected to V CC (F O = V CC ), the converter uses its internal oscillator and the digital filter first null is located at 5Hz. When the F O pin is connected to GND (F O = OV), the converter uses its internal oscillator and the digital filter first null is located at Hz. When F O is driven by an external clock signal with a frequency f EOSC, the converter uses this signal as its system clock and the digital filter first null is located at a frequency f EOSC /5. FU CTIO AL BLOCK DIAGRA U U W V CC INTERNAL OSCILLATOR GND AUTOCALIBRN AND CONTROL F O (INT/EXT) CH + IN + CH CH + CH MUX IN DIFFERENTIAL 3RD ORDER Σ MODULATOR + DECIMATING FIR SERIAL INTERFACE SCK CS REF + REF CH/CH PING-PONG FD Figure. Functional Block Diagram TEST CIRCUITS V CC.9k.9k C LOAD = pf C LOAD = pf Hi-Z TO V OH V OL TO V OH V OH TO Hi-Z TA3 Hi-Z TO V OL V OH TO V OL V OL TO Hi-Z TA

12 APPLIC S I FOR CONVERTER OPERN Converter Operation Cycle The LTC is a low power, Σ ADC with automatic alternate channel selection between the two differential channels and an easy-to-use 3-wire serial interface (see Figure ). Channel is selected automatically at power up and the two channels are selected alternately afterwards (ping-pong). Its operation is made up of three states. The converter operating cycle begins with the conversion, followed by the low power sleep state and ends with the data output (see Figure ). The 3-wire interface consists of serial data output (), serial clock (SCK) and chip select (CS). Initially, the LTC performs a conversion. Once the conversion is complete, the device enters the sleep state. The part remains in the sleep state as long as CS is HIGH. While in this sleep state, power consumption is reduced by nearly two orders of magnitude. The conversion result is held indefinitely in a static shift register while the converter is in the sleep state. Once CS is pulled LOW, the device exits the low power mode and enters the data output state. If CS is pulled HIGH before the first rising edge of SCK, the device returns to the low power sleep mode and the conversion result is still held in the internal static shift register. If CS remains LOW POWER UP IN + = CH +, IN = CH FALSE CONVERT SLEEP CS = LOW AND SCK TRUE DATA OUTPUT SWITCH CHANNEL F Figure. LTC State Transition Diagram after the first rising edge of SCK, the device begins outputting the conversion result. Taking CS high at this point will terminate the data output state and start a new conversion. There is no latency in the conversion result. The data output corresponds to the conversion just performed. This result is shifted out on the serial data out pin () under the control of the serial clock (SCK). Data is updated on the falling edge of SCK allowing the user to reliably latch data on the rising edge of SCK (see Figure 3). The data output state is concluded once 3 bits are read out of the ADC or when CS is brought HIGH. The device automatically initiates a new conversion and the cycle repeats. Through timing control of the CS and SCK pins, the LTC offers several flexible modes of operation (internal or external SCK and free-running conversion modes). These various modes do not require programming configuration registers; moreover, they do not disturb the cyclic operation described above. These modes of operation are described in detail in the Serial Interface Timing Modes section. Conversion Clock A major advantage the delta-sigma converter offers over conventional type converters is an on-chip digital filter (commonly implemented as a Sinc or Comb filter). For high resolution, low frequency applications, this filter is typically designed to reject line frequencies of 5Hz or Hz plus their harmonics. The filter rejection performance is directly related to the accuracy of the converter system clock. The LTC incorporates a highly accurate on-chip oscillator. This eliminates the need for external frequency setting components such as crystals or oscillators. Clocked by the on-chip oscillator, the LTC achieves a minimum of db rejection at the line frequency (5Hz or Hz ±%). Ease of Use The LTC data output has no latency, filter settling delay or redundant data associated with the conversion cycle. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing multiple analog voltages is easy.

13 APPLIC S I FOR The LTC performs offset and full-scale calibrations every conversion cycle. This calibration is transparent to the user and has no effect on the cyclic operation described above. The advantage of continuous calibration is extreme stability of offset and full-scale readings with respect to time, supply voltage change and temperature drift. Power-Up Sequence The LTC automatically enters an internal reset state when the power supply voltage V CC drops below approximately V. This feature guarantees the integrity of the conversion result and of the serial interface mode selection. (See the -wire I/O sections in the Serial Interface Timing Modes section.) When the V CC voltage rises above this critical threshold, the converter creates an internal power-on-reset (POR) signal with a typical duration of ms. The POR signal clears all internal registers and selects channel. Following the POR signal, the LTC starts a normal conversion cycle and follows the succession of states described above. The first conversion result following POR is accurate within the specifications of the device if the power supply voltage is restored within the operating range (.7V to 5.5V) before the end of the POR time interval. Reference Voltage Range This converter accepts a truly differential external reference voltage. The absolute/common mode voltage specification for the REF + and REF pins covers the entire range from GND to V CC. For correct converter operation, the REF + pin must always be more positive than the REF pin. The LTC can accept a differential reference voltage from.v to V CC. The converter output noise is determined by the thermal noise of the front-end circuits, and as such, its value in nanovolts is nearly constant with reference voltage. A decrease in reference voltage will not significantly improve the converter s effective resolution. On the other hand, a reduced reference voltage will improve the converter s overall INL performance. A reduced reference voltage will also improve the converter performance when operated with an external conversion clock (external F O signal) at substantially higher output data rates (see the Output Data Rate section). Input Voltage Range The analog input is truly differential with an absolute/ common mode range for the CH + /CH or CH + /CH input pins extending from GND.3V to V CC +.3V. Outside these limits, the ESD protection devices begin to turn on and the errors due to input leakage current increase rapidly. Within these limits, the LTC converts the bipolar differential input signal, V IN = IN + IN, from FS =.5 V REF to +FS =.5 V REF where V REF = REF + REF, with the selected channel referred as IN + and IN. Outside this range, the converter indicates the overrange or the underrange condition using distinct output codes. Input signals applied to the analog input pins may extend by 3mV below ground and above V CC. In order to limit any fault current, resistors of up to 5k may be added in series with the pins without affecting the performance of the device. In the physical layout, it is important to maintain the parasitic capacitance of the connection between these series resistors and the corresponding pins as low as possible; therefore, the resistors should be located as close as practical to the pins. The effect of the series resistance on the converter accuracy can be evaluated from the curves presented in the Input Current/Reference Current sections. In addition, series resistors will introduce a temperature dependent offset error due to the input leakage current. A na input leakage current will develop a ppm offset error on a 5k resistor if V REF = 5V. This error has a very strong temperature dependency. Output Data Format The LTC serial output data stream is 3 bits long. The first 3 bits represent status information indicating the conversion state, selected channel and sign. The next bits are the conversion result, MSB first. The remaining 5 bits are sub LSBs beyond the -bit level that may be included in averaging or discarded without loss of resolution. The third and fourth bit together are also used to indicate an underrange condition (the differential input voltage is below FS) or an overrange condition (the differential input voltage is above +FS). 3

14 APPLIC S I FOR Bit 3 (first output bit) is the end of conversion (EOC) indicator. This bit is available at the pin during the conversion and sleep states whenever the CS pin is LOW. This bit is HIGH during the conversion and goes LOW when the conversion is complete. Bit 3 (second output bit) is the selected channel indicator. The bit is LOW for channel and HIGH for channel selected. Bit 9 (third output bit) is the conversion result sign indicator (SIG). If V IN is >, this bit is HIGH. If V IN is <, this bit is LOW. Bit 8 (fourth output bit) is the most significant bit (MSB) of the result. This bit in conjunction with Bit 9 also provides the underrange or overrange indication. If both Bit 9 and Bit 8 are HIGH, the differential input voltage is above +FS. If both Bit 9 and Bit 8 are LOW, the differential input voltage is below FS. The function of these bits is summarized in Table. Table. LTC Status Bits Bit 3 Bit 3 Bit 9 Bit 8 Input Range EOC CH/CH SIG MSB V IN.5 V REF or V V IN <.5 V REF or.5 V REF V IN < V or V IN <.5 V REF or Bits 8-5 are the -bit conversion result MSB first. Bit 5 is the least significant bit (LSB). Bits - are sub LSBs below the -bit level. Bits - may be included in averaging or discarded without loss of resolution. Data is shifted out of the pin under control of the serial clock (SCK), see Figure 3. Whenever CS is HIGH, remains high impedance and any externally generated SCK clock pulses are ignored by the internal data out shift register. In order to shift the conversion result out of the device, CS must first be driven LOW. EOC is seen at the pin of the device once CS is pulled LOW. EOC changes real time from HIGH to LOW at the completion of a conversion. This signal may be used as an interrupt for an external microcontroller. Bit 3 (EOC) can be captured on the first rising edge of SCK. Bit 3 is shifted out of the device on the first falling edge of SCK. The final data bit (Bit ) is shifted out on the falling edge of the 3st SCK and may be latched on the rising edge of the 3nd SCK pulse. On the falling edge of the 3nd SCK pulse, goes HIGH indicating the initiation of a new conversion cycle. This bit serves as EOC (Bit 3) for the next conversion cycle. Table summarizes the output data format. As long as the voltage on the analog input pins is maintained within the.3v to (V CC +.3V) absolute maximum operating range, a conversion result is generated for any differential input voltage V IN from FS =.5 V REF to +FS =.5 V REF. For differential input voltages greater than +FS, the conversion result is clamped to the value corresponding to the +FS + LSB. For differential input voltages below FS, the conversion result is clamped to the value corresponding to FS LSB. CS BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT 5 BIT Hi-Z EOC CH/CH SIG MSB LSB SCK SLEEP DATA OUTPUT CONVERSION Figure 3. Output Data Timing F3

15 APPLIC S I FOR Table. LTC Output Data Format Differential Input Voltage Bit 3 Bit 3 Bit 9 Bit 8 Bit 7 Bit Bit 5 Bit V IN * EOC CH/CH SIG MSB V IN *.5 V REF ** /.5 V REF ** LSB /.5 V REF ** /.5 V REF ** LSB / / LSB /.5 V REF ** /.5 V REF ** LSB /.5 V REF ** / V IN * <.5 V REF ** / *The differential input voltage V IN = IN + IN. **The differential reference voltage V REF = REF + REF. LTC Frequency Rejection Selection (F O ) The LTC internal oscillator provides better than db normal mode rejection at the line frequency and all its harmonics for 5Hz ±% or Hz ±%. For Hz rejection, F O should be connected to GND while for 5Hz rejection the F O pin should be connected to V CC. The selection of 5Hz or Hz rejection can also be made by driving F O to an appropriate logic level. A selection change during the sleep or data output states will not disturb the converter operation. If the selection is made during the conversion state, the result of the conversion in progress may be outside specifications but the following conversions will not be affected. When a fundamental rejection frequency different from 5Hz or Hz is required or when the converter must be synchronized with an outside source, the LTC can operate with an external conversion clock. The converter automatically detects the presence of an external clock signal at the F O pin and turns off the internal oscillator. The frequency f EOSC of the external signal must be at least 5Hz (Hz notch frequency) to be detected. The external clock signal duty cycle is not significant as long as the minimum and maximum specifications for the high and low periods t HEO and t LEO are observed. While operating with an external conversion clock of a frequency f EOSC, the LTC provides better than db normal mode rejection in a frequency range f EOSC /5 ±% and its harmonics. The normal mode rejection as a function of the input frequency deviation from f EOSC /5 is shown in Figure. Whenever an external clock is not present at the F O pin, the converter automatically activates its internal oscillator and enters the Internal Conversion Clock mode. The LTC operation will not be disturbed if the change of conversion clock source occurs during the sleep state or during the data output state while the converter uses an external serial clock. If the change occurs during the conversion state, the result of the conversion in progress may be NORMAL MODE REJECTION (db) DIFFERENTIAL INPUT SIGNAL FREQUENCY DEVIN FROM NOTCH FREQUENCY f EOSC /5(%) F Figure. LTC Normal Mode Rejection When Using an External Oscillator of Frequency f EOSC 5

16 APPLIC S I FOR outside specifications but the following conversions will not be affected. If the change occurs during the data output state and the converter is in the Internal SCK mode, the serial clock duty cycle may be affected but the serial data stream will remain valid. Table 3 summarizes the duration of each state and the achievable output data rate as a function of F O. SERIAL INTERFACE PINS The LTC transmits the conversion results and receives the start of conversion command through a synchronous 3-wire interface. During the conversion and sleep states, this interface can be used to assess the converter status and during the data output state it is used to read the conversion result. Serial Clock Input/Output (SCK) The serial clock signal present on SCK (Pin 3) is used to synchronize the data transfer. Each bit of data is shifted out the pin on the falling edge of the serial clock. In the Internal SCK mode of operation, the SCK pin is an output and the LTC creates its own serial clock by dividing the internal conversion clock by 8. In the External SCK mode of operation, the SCK pin is used as input. The internal or external SCK mode is selected on power-up and then reselected every time a HIGH-to-LOW transition is detected at the CS pin. If SCK is HIGH or floating at powerup or during this transition, the converter enters the internal SCK mode. If SCK is LOW at power-up or during this transition, the converter enters the external SCK mode. Serial Data Output () The serial data output pin, (Pin ), provides the result of the last conversion as a serial bit stream (MSB first) during the data output state. In addition, the pin is used as an end of conversion indicator during the conversion and sleep states. When CS (Pin ) is HIGH, the driver is switched to a high impedance state. This allows sharing the serial interface with other devices. If CS is LOW during the convert or sleep state, will output EOC. If CS is LOW during the conversion phase, the EOC bit appears HIGH on the pin. Once the conversion is complete, EOC goes LOW. Chip Select Input (CS) The active LOW chip select, CS (Pin ), is used to test the conversion status and to enable the data output transfer as described in the previous sections. In addition, the CS signal can be used to trigger a new conversion cycle before the entire serial data transfer has been completed. The LTC will abort any serial data transfer in progress and start a new conversion cycle Table 3. LTC State Duration State Operating Mode Duration CONVERT Internal Oscillator F O = LOW 33ms, Output Data Rate 7.5 Readings/s (Hz Rejection) F O = HIGH ms, Output Data Rate. Readings/s (5Hz Rejection) External Oscillator F O = External Oscillator 5/f EOSC s, Output Data Rate f EOSC /5 Readings/s with Frequency f EOSC khz (f EOSC /5 Rejection) SLEEP As Long As CS = HIGH DATA OUTPUT Internal Serial Clock F O = LOW/HIGH As Long As CS = LOW But Not Longer Than.7ms (Internal Oscillator) (3 SCK cycles) F O = External Oscillator with As Long As CS = LOW But Not Longer Than 5/f EOSC ms Frequency f EOSC khz (3 SCK cycles) External Serial Clock with As Long As CS = LOW But Not Longer Than 3/f SCK ms Frequency f SCK khz (3 SCK cycles)

17 APPLIC S I FOR anytime a LOW-to-HIGH transition is detected at the CS pin after the converter has entered the data output state (i.e., after the first rising edge of SCK occurs with CS = LOW). Finally, CS can be used to control the free-running modes of operation, see Serial Interface Timing Modes section. Grounding CS will force the ADC to continuously convert at the maximum output rate selected by F O. SERIAL INTERFACE TIMING MODES The LTC s 3-wire interface is SPI and MICROWIRE compatible. This interface offers several flexible modes of operation. These include internal/external serial clock, - or 3-wire I/O, single cycle conversion and autostart. The following sections describe each of these serial interface timing modes in detail. In all these cases, the converter can use the internal oscillator (F O = LOW or F O = HIGH) or an external oscillator connected to the F O pin. Refer to Table for a summary. External Serial Clock, Single Cycle Operation (SPI/MICROWIRE Compatible) This timing mode uses an external serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 5. The serial clock mode is selected on the falling edge of CS. To select the external serial clock mode, the serial clock pin (SCK) must be LOW during each CS falling edge. Table. LTC Interface Timing Modes Conversion Data Connection SCK Cycle Output and Configuration Source Control Control Waveforms External SCK, Single Cycle Conversion External CS and SCK CS and SCK Figures 5, External SCK, -Wire I/O External SCK SCK Figure 7 Internal SCK, Single Cycle Conversion Internal CS CS Figures 8, 9 Internal SCK, -Wire I/O, Continuous Conversion Internal Continuous Internal Figure.7V TO 5.5V µf V CC F O LTC REFERENCE REF + VOLTAGE.V TO V CC 3 REF SCK 3 5 CH + CH CS 7 CH + CH GND 8, 9,, 5, ANALOG INPUT RANGE.5V REF TO.5V REF V CC = 5Hz REJECTION = EXTERNAL OSCILLATOR = Hz REJECTION 3-WIRE SPI INTERFACE CS TEST EOC BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT BIT 5 BIT TEST EOC Hi-Z Hi-Z EOC CH/CH SIG MSB LSB SUB LSB Hi-Z SCK (EXTERNAL) CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION F5 TEST EOC (OPTIONAL) Figure 5. External Serial Clock, Single Cycle Operation 7

18 APPLIC S I FOR The serial data output pin () is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. While CS is pulled LOW, EOC is output to the pin. EOC = while a conversion is in progress and EOC = if the device is in the sleep state. With CS high, the device automatically enters the low power sleep state once the conversion is complete. When the device is in the sleep state (EOC = ), its conversion result is held in an internal static shift register. Data is shifted out the pin on each falling edge of SCK. This enables external circuitry to latch the output on the rising edge of SCK. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 3nd rising edge of SCK. On the 3nd falling edge of SCK, the device begins a new conversion. goes HIGH (EOC = ) indicating a conversion is in progress. At the conclusion of the data cycle, CS may remain LOW and EOC monitored as an end-of-conversion interrupt. Alternatively, CS may be driven HIGH setting to Hi-Z. As described above, CS may be pulled LOW at any time in order to monitor the conversion status. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first rising edge and the 3nd falling edge of SCK, see Figure. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for systems not requiring all 3 bits of output data, aborting an invalid conversion cycle or synchronizing the start of a conversion. External Serial Clock, -Wire I/O This timing mode utilizes a -wire serial I/O interface. The conversion result is shifted out of the device by an externally generated serial clock (SCK) signal, see Figure 7. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The external serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded ANALOG INPUT RANGE.5V REF TO.5V REF.7V TO 5.5V µf V CC F O LTC REFERENCE REF + VOLTAGE 3 3.V TO V CC REF SCK 5 CH + CH CS 7 CH + CH GND 8, 9,, 5, V CC = 5Hz REJECTION = EXTERNAL OSCILLATOR = Hz REJECTION 3-WIRE SPI INTERFACE CS BIT TEST EOC BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT 9 BIT 8 TEST EOC EOC Hi-Z Hi-Z Hi-Z EOC CH/CH SIG MSB Hi-Z SCK (EXTERNAL) SLEEP DATA OUTPUT CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION F TEST EOC (OPTIONAL) 8 Figure. External Serial Clock, Reduced Data Output Length

19 APPLIC S I FOR.7V TO 5.5V µf V CC F O LTC REFERENCE REF + VOLTAGE.V TO V CC 3 REF SCK 3 CH + 5 ANALOG INPUT RANGE CH CS.5V REF TO.5V REF CH + 7 CH GND V CC = 5Hz REJECTION = EXTERNAL OSCILLATOR = Hz REJECTION -WIRE INTERFACE 8, 9,, 5, CS BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT BIT 5 BIT EOC CH/CH SIG MSB LSB SCK (EXTERNAL) CONVERSION DATA OUTPUT CONVERSION F7 Figure 7. External Serial Clock, CS = Operation (-Wire) typically ms after V CC exceeds V. The level applied to SCK at this time determines if SCK is internal or external. SCK must be driven LOW prior to the end of POR in order to enter the external serial clock timing mode. Since CS is tied LOW, the end-of-conversion (EOC) can be continuously monitored at the pin during the convert and sleep states. EOC may be used as an interrupt to an external controller indicating the conversion result is ready. EOC = while the conversion is in progress and EOC = once the conversion ends. On the falling edge of EOC, the conversion result is loaded into an internal static shift register. Data is shifted out the pin on each falling edge of SCK enabling external circuitry to latch data on the rising edge of SCK. EOC can be latched on the first rising edge of SCK. On the 3nd falling edge of SCK, goes HIGH (EOC = ) indicating a new conversion has begun. Internal Serial Clock, Single Cycle Operation This timing mode uses an internal serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 8. In order to select the internal serial clock timing mode, the serial clock pin (SCK) must be floating (Hi-Z) or pulled HIGH prior to the falling edge of CS. The device will not enter the internal serial clock mode if SCK is driven LOW on the falling edge of CS. An internal weak pull-up resistor is active on the SCK pin during the falling edge of CS; therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven. The serial data output pin () is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. Once CS is pulled LOW, SCK goes LOW and EOC is output to the pin. EOC = while a conversion is in progress and EOC = if the device is in the sleep state. When testing EOC, if the conversion is complete (EOC = ), the device will exit the sleep state during the EOC test. In order to allow the device to return to the low power sleep state, CS must be pulled HIGH before the first rising edge of SCK. In the internal SCK timing mode, SCK goes HIGH and the device begins outputting data at time t EOCtest after the falling edge of CS (if EOC = ) or t EOCtest after EOC goes LOW (if CS is LOW during the falling edge of EOC). The value of t EOCtest is 3µs if the device is using its internal oscillator (F = logic LOW or HIGH). If F O is driven by an external oscillator of frequency f EOSC, then t EOCtest is 3./f EOSC. If CS is pulled HIGH before time t EOCtest, the 9

20 APPLIC S I FOR.7V TO 5.5V µf V CC F O LTC REFERENCE REF + VOLTAGE.V TO V CC 3 REF SCK 3 5 CH + CH CS 7 CH + CH GND 8, 9,, 5, ANALOG INPUT RANGE.5V REF TO.5V REF V CC = 5Hz REJECTION = EXTERNAL OSCILLATOR = Hz REJECTION 3-WIRE SPI INTERFACE V CC k <t EOCtest CS BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT BIT 5 BIT TEST EOC EOC CH/CH SIG MSB LSB Hi-Z Hi-Z Hi-Z Hi-Z SCK (INTERNAL) CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION F8 TEST EOC (OPTIONAL) Figure 8. Internal Serial Clock, Single Cycle Operation device returns to the sleep state and the conversion result is held in the internal static shift register. If CS remains LOW longer than t EOCtest, the first rising edge of SCK will occur and the conversion result is serially shifted out of the pin. The data output cycle concludes after the 3nd rising edge. Data is shifted out the pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result on the 3nd rising edge of SCK. After the 3nd rising edge, goes HIGH (EOC = ), SCK stays HIGH and a new conversion starts. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first and 3nd rising edge of SCK, see Figure 9. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for systems not requiring all 3 bits of output data, aborting an invalid conversion cycle, or synchronizing the start of a conversion. If CS is pulled HIGH while the converter is driving SCK LOW, the internal pull-up is not available to restore SCK to a logic HIGH state. This will cause the device to exit the internal serial clock mode on the next falling edge of CS. This can be avoided by adding an external k pull-up resistor to the SCK pin or by never pulling CS HIGH when SCK is LOW. Whenever SCK is LOW, the LTC s internal pull-up at pin SCK is disabled. Normally, SCK is not externally driven if the device is in the internal SCK timing mode. However, certain applications may require an external driver on SCK. If this driver goes Hi-Z after outputting a LOW signal, the LTC s internal pull-up remains disabled. Hence, SCK remains LOW. On the next falling edge of CS, the device is switched to the external SCK timing mode. By adding an external k pull-up resistor to SCK, this pin goes HIGH once the external driver goes Hi-Z. On the next CS falling edge, the device will remain in the internal SCK timing mode. A similar situation may occur during the sleep state when CS is pulsed HIGH-LOW-HIGH in order to test the conversion status. If the device is in the sleep state (EOC = ), SCK will go LOW. Once CS goes HIGH (within the time period defined above as t EOCtest ), the internal pull-up is activated. For a heavy capacitive load on the SCK pin, the

21 APPLIC S I FOR ANALOG INPUT RANGE.5V REF TO.5V REF.7V TO 5.5V µf V CC F O LTC REFERENCE REF + VOLTAGE 3 3.V TO V CC REF SCK 5 CH + CH CS 7 CH + CH GND 8, 9,, 5, V CC = 5Hz REJECTION = EXTERNAL OSCILLATOR = Hz REJECTION 3-WIRE SPI INTERFACE V CC k >t EOCtest <t EOCtest CS BIT TEST EOC BIT 3 BIT 3 BIT 9 BIT 8 BIT 7 BIT BIT 8 TEST EOC EOC EOC CH/CH SIG MSB Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z SCK (INTERNAL) SLEEP DATA OUTPUT CONVERSION SLEEP SLEEP TEST EOC (OPTIONAL) DATA OUTPUT CONVERSION F9 Figure 9. Internal Serial Clock, Reduced Data Output Length internal pull-up may not be adequate to return SCK to a HIGH level before CS goes low again. This is not a concern under normal conditions where CS remains LOW after detecting EOC =. This situation is easily overcome by adding an external k pull-up resistor to the SCK pin. Internal Serial Clock, -Wire I/O, Continuous Conversion This timing mode uses a -wire, all output (SCK and ) interface. The conversion result is shifted out of the device by an internally generated serial clock (SCK) signal, see Figure. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The internal serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded approximately ms after V CC exceeds V. An internal weak pull-up is active during the POR cycle; therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven LOW (if SCK is loaded such that the internal pull-up cannot pull the pin HIGH, the external SCK mode will be selected). During the conversion, the SCK and the serial data output pin () are HIGH (EOC = ). Once the conversion is complete, SCK and go LOW (EOC = ) indicating the conversion has finished and the device has entered the data output state. The data output cycle begins on the first rising edge of SCK and ends after the 3nd rising edge. Data is shifted out the pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 3nd rising edge of SCK. After the 3nd rising edge, goes HIGH (EOC = ) indicating a new conversion is in progress. SCK remains HIGH during the conversion.