Series HMPA and HHPA Power Amplifiers
|
|
|
- Elinor Daniel
- 5 years ago
- Views:
Transcription
1 DESCRIPTION The HMPA and HHPA Series of cover the frequency range from GHz. A wide variety of gain and bandwidth combinations are available to provide the designer with a solution for most applications. Custom designs are available and in most cases, NRE is not required. MMIC technology is employed for high reliability and repeatability. The amplifiers can be used in transmitters for communication and radar systems and also as gain blocks in LO chains and test equipment. Multiple devices can be combined to increase output power where necessary. For example, several watts of power have been obtained at 35 GHz. The amplifiers can also be packaged with other components for custom configurations. Each power amplifier contains a voltage regulator and bias sequencing circuitry allowing the use of a single bias to power the amplifier. Applications Communications Equipment Radar Transmitters Test Equipment Features High P1dB or PSAT Multiple Gain / P1dB options Single Bias / Internal Regulation Internal Bias Sequencing Custom power combining available
2 Power Amplifier Specifications - 18 to 70 GHz This is just a sample listing of available power amplifiers. Please choose from these models or contact factory with your requirements. Please identify your required frequency range with any inquiry. Model Number Frequency Range (GHz) Input/Output P 1dB (dbm) Gain (db) HMPAAK mm, Female HHPAAK mm, Female HHPAKK mm, Female HHPAKK mm, Female HHPAA WR-28, UG-599/U HMPAAK mm, Female HHPAA WR-28, UG-599/U HHPAA WR-28, UG-599/U HHPAA WR-28, UG-599/U HHPAB WR-22, UG-599/U-M HMPAB mm, Female HHPAVC mm Female HHPAV WR-15, UG- 385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG-385/U HHPAV WR-15, UG-385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG- 385/U HHPAV WR-15, UG-385/U See next 2 pages for above 50 GHz C T CASE, Specifications subject to change w/o notice.
3 Power Amplifier Specifications - 70 to 100 GHz This is just a sample listing of available power amplifiers. Please choose from these models or contact factory with your requirements. Please identify your required frequency range with any inquiry. Model Number Frequency Range (GHz) Input/Output P 1dB (dbm) Gain (db) HHPAE WR-12, UG-387/U HHPAE WR-12, UG-387/U HHPAE WR-12, UG-387/U HHPAW WR-10, UG-387/U-M HHPAE WR-12, UG-387/U HHPAW WR-10, UG-387/U-M HHPAW WR-10, UG-387/U-M HHPAW WR-10, UG-387/U-M HHPAE WR-12, UG-387/U HHPAE WR-12, UG-387/U HHPAE WR-12, UG-387/U HHPAW WR-10, UG-387/U-M +20 (P SAT ) 30 HMPAW WR-10, UG-387/U-M HMPAW WR-10, UG-387/U-M HMPAW WR-10, UG-387/U-M HHPAW WR-10, UG-387/U-M +15 (P SAT ) 18 HHPAW-262* WR-10, UG-387/U-M +24 (P SAT ) C T CASE, Specifications subject to change w/o notice. * This model is not available outside the USA.
4 Power Amplifier Outlines Coaxial Power Amplifier (2.9 and 2.4 mm connectors) Q-Band (B-Band, WR-22) Power Amplifier (Outline is also valid for Ka-Band.)
5 Power Amplifier Outlines V-Band (WR-15) Power Amplifier Coaxial Power Amplifier (1.85 mm connectors)
6 Power Amplifier Outlines E-Band (WR-12) Power Amplifier W-Band (WR-10) Power Amplifier
7 Requesting quotes When requesting a quote for HMPA or HHPA High, please specify required frequency range and any other required specifications. The amplifiers are built to order and will be optimized for the bandwidth specified by the customer. The part number guide below can also be used as a reference for requesting quotes. HHPA V - XXX Interface Options SMA female connectors available to 20 GHz. 2.9 mm connectors available through 40 GHz. 2.4 mm connectors available through 50 GHz mm connectors available through 65 GHz. Assigned by factory Frequency Band HXI Model #
Series HLNA Low Noise Amplifiers
DESCRIPTION The HLNA Series of covers the frequency ranges from 18 to 110 GHz. A wide variety of gain and bandwidth combinations are available to provide the designer with a solution for most applications.
Series HAFM Active Frequency Multipliers
DESCRIPTION The HAFM Series of active multipliers is available in models ranging from 30 to 100 GHz. A wide variety of multiplication factors from X2 up to X6 provide the customer with design flexibility
SERIES LNA LOW NOISE AMPLIFIERS DESCRIPTION. Millimeter-Wave Technology & Solutions
LOW NOISE AMPLIFIERS FEATURES: Wideband coverage Modular compact design Military or commercial units available 2.92, 2.4, 1.85 mm or Waveguide interfaces as required Internal voltage regulation and bias
Features. The HMC-C072 is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT. = +25 C, Vdc = +7V
amplifiers Typical Applications The is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram Features Ultra Low Phase Noise: -67 dbc/hz @ khz Noise Figure: 4.5 db Gain:
Features. = +25 C, +Vdc = +6V, -Vdc = -5V
v3.7 WIDEBAND LNA MODULE, - 2 GHz amplifiers Typical Applications The Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Industrial Sensors Functional
Features. Gain Variation Over Temperature db/ C
HMC-C26 Features Typical Applications The HMC-C26 Wideband PA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Gain: 3 db
Clarke & Severn Electronics Ph
Clarke & Severn Electronics Ph +612 9482 1944 Email sales@clarke.com.au www.cseonline.com.au POWER AMPLIFIER FPA-22-0001 - 43-46GHz FPA-15-0001- 55-65GHz FPA-12-0001- 71-77GHz FPA-10-0003 - 75-110GHz FPA-10-0004
Features. = +25 C, Vdc = +7V
amplifiers Typical Applications The is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram Features Ultra Low Phase Noise: -7 dbc/hz @ khz Noise Figure: 6 db Gain:
SPA SMA DATA SHEET
43 db Gain Medium Power High Gain Amplifier at 3 Watt P1dB Operating From 14.4 GHz to 15.4 GHz with 41 dbm IP3 and SMA SPA-154-43-03-SMA is a 3 Watt Ku Band high gain power coaxial amplifier operating
Features. = +25 C, +Vdc = +6V, -Vdc = -5V
HMC-C59 v.59 WIDEBAND LNA MODULE, - 2 GHz Typical Applications The HMC-C59 Wideband LNA is ideal for: Telecom Infrastructure Features Noise Figure:.8 db @ 8 GHz High Gain: 6 db @ 8 GHz PdB Output Power:
FMAM4032 DATA SHEET. 10 MHz to 6 GHz, Medium Power Broadband Amplifier with 900 mw, 24 db Gain and SMA. Features: Applications:
FMAM432 1 MHz to 6 GHz, Medium Power Broadband Amplifier with 9 mw, 24 db Gain and SMA FMAM432 two stage amplifier operates across a wide frequency range from 1 MHz to 6 GHz The design utilizes GaAs PHEMT
Features. = +25 C, Vs= +8V to +16V
v2.17 Typical Applications The Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Features Electrical Specifications,
Features. = +25 C, Vdc = +5V
amplifiers Typical Applications The HMC-C is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram v.7 HMC-C Features Ultra Low Phase Noise: -6 dbc/hz @ khz Noise Figure:
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier AM14344WM-BM-R AM14344WM-FM-R Aug Rev DESCRIPTION AMCOM s is part of the GaAs HiFET MMIC power amplifier series. This high efficiency MMIC is a 2-stage GaAs phemt power amplifier
PCS Base Station High output power, P1dB = 38 dbm. GPS Applications High gain > 20 db. WLAN Repeaters Efficiency > 30%
AM143438WM-BM-R AM143438WM-FM-R DESCRIPTION AMCOM s AM143438WM-BM-R and AM143438WM-FM-R are part of the GaAs HiFET MMIC power amplifier series. These high efficiency MMICs are 2-stage GaAs phemt power
CTT Technical Proposal
CTT Technical Proposal 6-1 GHz 0 W Power Amplifier (GaAs and GaN approaches) SECTION 1: 6-1 GHz 0 W power amplifiers A) Specification and comparison SECTION 2: GaAs 6-1 GHz Solid State Power Amplifier
SERIES AMC ACTIVE MULTIPLIER CHAIN FEATURES: APPLICATIONS: DESCRIPTION. Millimeter-Wave Technology & Solutions
ACTIVE MULTIPLIER CHAIN FEATURES: Full waveguide bandwidths Optional Removable Heatsink Compact package APPLICATIONS: LO source for up/down converters Frequency extenders DESCRIPTION Millitech s line of
SERIES MXP BALANCED MIXERS FEATURES: APPLICATIONS: DESCRIPTION
BALANCED MIXERS FEATURES: Low conversion loss and noise figure 13 dbm LO drive power Matched IF amplifier and LO offered Small, rugged package APPLICATIONS: DESCRIPTION Millitech series MXP balanced mixers
FMAM1035 DATA SHEET. 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA. Features: Applications:
FMAM13 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA The FMAM13 is a low phase noise amplifier that operates across the frequency range from 3 GHz
SERIES DET GENERAL PURPOSE DETECTORS DESCRIPTION. Millimeter-Wave Technology & Solutions
GENERAL PURPOSE DETECTORS FEATURES: Full waveguide bandwidth High sensitivity No tuning required Zero bias APPLIC ATIONS: Instrumentation Power monitoring DESCRIPTION Millitech series DET detectors, utilizing
AM002535MM-BM-R AM002535MM-FM-R
AM002535MM-BM-R AM002535MM-FM-R December 2008 Rev. 1 DESCRIPTION AMCOM s AM002535MM-BM-R is part of the GaAs MMIC power amplifier series. It has 24 db gain, 34 dbm output power over most of the 0.03 to
Linear High Power Amplifiers
PRODUCTS Linear High Power Amplifiers Aethercomm designs and manufactures high power class A and AB linear amplifiers to transmit voice, data and video for military systems, wireless customers and industrial
and GHz. ECE Radiometer. Technical Description and User Manual
E-mail: sales@elva-1.com http://www.elva-1.com 26.5-40 and 76.5-90 GHz ECE Radiometer Technical Description and User Manual November 2008 Contents 1. Introduction... 3 2. Parameters and specifications...
Features. = +25 C, Vdd = 5V
v3.117 HMC1LH5 Typical Applications The HMC1LH5 is a medium PA for: Telecom Infrastructure Military Radio, Radar & ECM Space Systems Test Instrumentation Functional Diagram Features Gain: 5 db Saturated
BROADBAND DISTRIBUTED AMPLIFIER
ADM1-26PA The ADM1-26PA is a complete LO driver solution for use with all Marki mixers up to 26. GHz. This single-stage packaged GaAs MMIC distributed amplifier integrates all required biasing circuitry.
Features. = +25 C, Vdd= +12V, Vgg2= +5V, Idd= 400 ma*
Typical Applications The HMC637LP5(E) wideband PA is ideal for: Features P1dB Output Power: +29 dbm Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional
Features. = +25 C, Vdd= 8V, Idd= 75 ma*
HMC46LC5 Typical Applications v3.11 AMPLIFIER, DC - 2 GHz Features The HMC46LC5 is ideal for: Noise Figure: 2.5 db @ 1 GHz Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation
Features. = +25 C, Vdd= 5V. Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units. Frequency Range GHz
Typical Applications The HMC62LP / HMC62LPE Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C 3 I Test Instrumentation Fiber Optics Functional Diagram Features
Features OBSOLETE. = +25 C, as a function of Vdd. Vdd = +3V Vdd = +5V Vdd = +5V Vdd = +5V Parameter
v5.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER,. - 3. GHz Typical Applications Broadband or Narrow Band Applications: Cellular/PCS/3G Fixed Wireless & Telematics Cable Modem Termination Systems
8 11 GHz 1 Watt Power Amplifier
Rev. 1.1 December 2 GHz 1 Watt Power Amplifier Features Frequency Range : GHz 3 dbm output P1dB. db Power gain 3% PAE High IP3 Input Return Loss > db Output Return Loss > db Dual bias operation No external
27-31 GHz 2W Balanced Power Amplifier TGA4513-CP
27-31 GHz 2W Balanced Power Amplifier Key Features 27-31 GHz Bandwidth > 32 dbm Nominal P1dB 33 dbm Nominal Psat 22 db Nominal Gain IMD3 is 32 dbc @ 18 dbm SCL 12 db Nominal Return Loss Bias: 6 V, 84 ma
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier AM324036WM-BM-R AM324036WM-FM-R Aug 10 Rev 6 DESCRIPTION AMCOM s is part of the GaAs MMIC power amplifier series. It has 29dB gain and 36dBm output power over the 3.2 to 4.0GHz
Features = +5V. = +25 C, Vdd 1. = Vdd 2
v7.11 HMC1LC3 POWER AMPLIFIER, - GHz Typical Applications The HMC1LC3 is ideal for use as a medium power amplifier for: Microwave Radio & VSAT Military & Space Test Equipment & Sensors Fiber Optics LO
10 W, GaN Power Amplifier, 2.7 GHz to 3.8 GHz HMC1114
9 13 16 FEATURES High saturated output power (PSAT): 41.5 dbm typical High small signal gain: db typical High power gain for saturated output power:.5 db typical Bandwidth: 2.7 GHz to 3.8 GHz High power
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier AM1327MM-BM-R AM1327MM-FM-R Aug 2010 Rev 2 DESCRIPTION AMCOM s is part of the GaAs HiFET MMIC power amplifier series. It is a 2-stage GaAs HIFET MESFET MMIC power amplifier biased
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier AM14MM-BM-R AM14MM-FM-R Aug 10 Rev 8 DESCRIPTION AMCOM s is part of the GaAs HiFET MMIC power amplifier series. It is a 2-stage GaAs MESFET MMIC power amplifier biased at 14V.
>10 W, GaN Power Amplifier, 0.01 GHz to 1.1 GHz HMC1099
9 1 11 12 13 14 1 16 32 GND 31 29 28 27 26 FEATURES High saturated output power (PSAT):. dbm typical High small signal gain: 18. db typical High power added efficiency (PAE): 69% typical Instantaneous
Terabeam/HXI Millimeter Wave Product Availability
Terabeam/HXI was founded as Harmonix Corporation in 1992. The company was a pioneer in the development of 60 GHz, high data rate communication links between buildings where connection to fiber was not
Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2]
![Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2]](/thumbs/94/119028866.jpg "Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2]")
Typical Applications This is ideal for: Features Low Noise Figure: 1.8 db Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram High Gain: 19 db High
Features. Parameter Min. Typ. Max. Units. Frequency Range 8 12 GHz Insertion Loss* db. Input Return Loss* 10 db
v4.711 HMC-C Features Low RMS Phase Error: Low Insertion Loss: 7 db Excellent Flatness 3 Coverage, LSB = 22. Hermetically Sealed Module Field Replaceable SMA Female Connectors Typical Applications The
Features. = +25 C, Vdd = +7V, Idd = 1340 ma [1]
![Features. = +25 C, Vdd = +7V, Idd = 1340 ma [1]](/thumbs/89/100552958.jpg "Features. = +25 C, Vdd = +7V, Idd = 1340 ma [1]")
Typical Applications The HMC591LP5 / HMC591LP5E is ideal for use as a power amplifi er for: Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment & Sensors Military End-Use Space Features Saturated
Engineering the high quality cost effective solutions. Short form selection catalogue
Engineering the high quality cost effective solutions Short form selection catalogue 19 Rack mountable systems NML offers variety of upconverters, downconverters, multicouplers, synthesisers for various
1-24 GHz Distributed Driver Amplifier
Features Functional Block Diagram Wide bandwidth High linearity Single positive supply voltage On chip bias choke Description The CMD197C4 is a wideband GaAs MMIC driver amplifier housed in a leadless
HMC997LC4. Variable Gain Amplifier - SMT. VARIABLE GAIN AMPLIFIER GHz. Typical Applications. General Description. Functional Diagram
v2.14 Typical Applications The is ideal for: Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM Subsystems Ka-Band Radar Test Equipment Functional Diagram Features Wide Gain Control Range: 1 db Single
0.5-4GHz Low Noise Amplifier
.5-4GHz Low Noise Amplifier Features Frequency Range:.5-4 GHz Better than 2.dB Noise Figure Single supply operation db Nominal Gain dbm Nominal P1dB Input Return Loss > db Output Return Loss > db DC decoupled
2 GHz to 6 GHz, 500 W Power Amplifier HMC8113
Data Sheet FEATURES 2 GHz to 6 GHz frequency range 85 db typical small signal gain 57 dbm typical saturated output power 61 db gain control range with 1 db LSB Standard 5U 19-inch rack chassis (per EIA-310D)
Small Integrated Transmitter Unit SITU2400-XZ
Small Integrated Transmitter Unit SITU2400-XZ 0.05 1 GHz, ITU-Grid DWDM Directly Modulated Self-Contained Transmitter Applications Cellular and PCS Antenna- Remoting Microwave Delay Lines Frequency Distribution
0.5-4GHz Low Noise Amplifier
ASL P3.5-4GHz Low Noise Amplifier Features Frequency Range:.5-4 GHz Better than 2.dB Noise Figure Single supply operation db Nominal Gain dbm Nominal P1dB Input Return Loss > db Output Return Loss > db
TEL: FAX: v.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER, GHz Broadband Gain & Return Vdd =
TEL:7-339622 FAX:7-337612 E-MAIL: szss@3.com v.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER,. - 3. GHz Typical Applications Broadband or Narrow Band Applications: Cellular/PCS/3G Fixed Wireless
Features. = +25 C, Vdd =+28V, Idd = 850 ma [1]
![Features. = +25 C, Vdd =+28V, Idd = 850 ma [1]](/thumbs/87/97234843.jpg "Features. = +25 C, Vdd =+28V, Idd = 850 ma [1]")
v1.413 HMC87F POWER AMPLIFIER, 2 - GHz Typical Applications The HMC86F is ideal for Test Instrumentation General Communications Radar Functional Diagram Features High Psat: +38. dbm Power Gain at Psat:
Features. Output Power for 1 db Compression (P1dB) dbm Saturated Output Power (Psat) dbm
v1.314 Typical Applications Features The is ideal for: Test Instrumentation Microwave Radio & VSAT Telecom Infrastructure Military & Space Fiber optics Functional Diagram P1dB Output Power: +27 dbm Psat
SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER,
v2.617 AMPLIFIER, - 12 GHz Typical Applications The is ideal for use as a power amplifier for: Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment and Sensors Military End-Use Features Saturated
AM003536WM-BM-R AM003536WM-FM-R
AM0036WM-BM-R AM0036WM-FM-R DESCRIPTION AMCOM s is an ultra broadband GaAs MMIC power amplifier. It has 23 db gain, and 36 dbm output power over the 0.01 to 3.5 GHz band. This MMIC is in a ceramic package
S Band 7 Bit Digital Attenuator
S Band 7 Bit Digital Attenuator Features Frequency Range: 2.8-3.8 GHz Low Insertion Loss 4 db(typ.) Max. Attenuation of 31.75 db RMS Amplitude Error < 0.3 db Input & Output Return Loss > 12 db 32 Lead
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier December 2012 Rev0 DESCRIPTION AMCOM s AM357039WM is a broadband GaAs MMIC Power Amplifier. It has a nominal CW performance of 21dB small signal gain, and 38.5dBm (7W) saturated
11-15 GHz 0.5 Watt Power Amplifier
11-15 GHz 0.5 Watt Power Amplifier Features Frequency Range : 11-15GHz 27.5 dbm output Psat 13 db Power gain 25% PAE High IP3 Input Return Loss > 11 db Output Return Loss > 6 db Dual bias operation No
Parameter Symbol Units MIN MAX. RF Input power (CW) Pin dbm +20
AMT-A0142 1 GHz to 18 GHz Broadband Medium Power with Low Noise Amplifier Data Sheet Features 1 GHz to 18 GHz Frequency Range Typical P1dB power > +23 dbm Gain 18 db Typical Gain Flatness ± 1 db Typical
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v3.38 POWER AMPLIFIER, 2-2 GHz Typical
SERIES PLS PHASE LOCKED SYNTHESIZER. FEATURES: Small Size, Low Cost, Simple to use Low Phase Noise Auto-sensing Internal or External 10MHz Reference
PHASE LOCKED SYNTHESIZER FEATURES: Small Size, Low Cost, Simple to use Low Phase Noise Auto-sensing Internal or External 10MHz Reference Can be utilized as a synthesizer, or a fixed frequency oscillator
87415A microwave system amplifier A microwave. system amplifier A microwave system amplifier A microwave.
20 Amplifiers 83020A microwave 875A microwave 8308A microwave 8307A microwave 83006A microwave 8705C preamplifier 8705B preamplifier 83050/5A microwave The Agilent 83006/07/08/020/050/05A test s offer
HMC486LP5 / 486LP5E LINEAR & POWER AMPLIFIERS - SMT. SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 7-9 GHz. Typical Applications.
v2. Typical Applications The HMC486LP5(E) is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment and Sensors Military End-Use Features Saturated Power: +33 dbm @ 2% PAE Output IP3:
Features. = +25 C, Vdd= 5V, Vgg2= Open, Idd= 60 ma*
v.7 HMCLH AGC AMPLIFIER, - GHz Typical Applications The HMCLH is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C I Test Instrumentation Fiber Optics Functional Diagram Features
GaAs MMIC Power Amplifier for VSAT & ITU Applications
GaAs MMIC Power Amplifier for VSAT & ITU Applications AM1351642WM-XX-R April 216 Rev 4 DESCRIPTION AMCOM s AM1351642WM--R is a Ku-band GaAs MMIC power amplifier designed for VSAT ground station transmitter
GaAs MMIC Double Balanced Mixer. Description Package Green Status
GaAs MMIC Double Balanced Mixer MM1-0212SSM 1. Device Overview 1.1 General Description The MM1-0212SSM is a highly linear GaAs MMIC double balanced mixer. MM1-0212SSM is a low frequency, high linearity
MMA GHz, 0.1W Gain Block Data Sheet
Features: Frequency Range: 6 22 GHz P1dB: 18.5 dbm @Vds=5V Psat: 19.5 dbm @ Gain: 14 db Vdd =3 to 6 V Ids = 13 ma Input and Output Fully Matched to 5 Ω Applications: Communication systems Microwave instrumentations
5 6.4 GHz 2 Watt Power Amplifier
5 6.4 GHz 2 Watt Power Amplifier Features Frequency Range : 5 6.4GHz 32.5 dbm output P1dB 9 db Power gain 32% PAE High IP3 Input Return Loss > 12 db Output Return Loss > 12 db Dual bias operation No external
5 6 GHz 10 Watt Power Amplifier
5 6 GHz 10 Watt Power Amplifier Features Frequency Range : 5 6GHz 40 dbm Output Power 18 db Power gain 30% PAE High IP3 Input Return Loss > 12 db Output Return Loss > 7.5 db Dual bias operation No external
SHF Communication Technologies AG. Wilhelm-von-Siemens-Str. 23D Berlin Germany. Phone / Fax /
SHF Communication Technologies AG Wilhelm-von-Siemens-Str. 23D 12277 Berlin Germany Phone ++49 30 / 772 05 10 Fax ++49 30 / 753 10 78 E-Mail: sales@shf.de Web: http://www.shf.de Datasheet SHF 826H Broadband
Features = +5V. = +25 C, Vdd 1. = Vdd 2
v1.11 HMC51LP3 / 51LP3E POWER AMPLIFIER, 5-1 GHz Typical Applications The HMC51LP3(E) is ideal for: Microwave Radio & VSAT Military & Space Test Equipment & Sensors Fiber Optics LO Driver for HMC Mixers
Features. = +25 C, Vdd= 8V, Vgg2= 3V, Idd= 290 ma [1]
![Features. = +25 C, Vdd= 8V, Vgg2= 3V, Idd= 290 ma [1]](/thumbs/95/123095816.jpg "Features. = +25 C, Vdd= 8V, Vgg2= 3V, Idd= 290 ma [1]")
Typical Applications The is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C 3 I Test Instrumentation Fiber Optics Functional Diagram Features P1dB Output Power: + dbm Gain:
SLA SMA DATA SHEET
SLA-6-8-4-SMA 8 Gain Limiting Amplifier Operating From 2 GHz to 6 GHz with -61 to 1 Pin, 1 Psat and SMA The SLA-6-8-4-SMA is a 2 to 6 GHz high gain wide-band coaxial limiting amplifier. The model operates
Millimeter Wave Product Catalogue VivaTech Consulting S.A.R.L.
VivaTech Consulting S.A.R.L. sales@vivatech.biz Telephone: +33 04 89 01 14 61 Fax: +33 04 93 87 08 66 Table of Contents Millimeter Wave Low Noise Amplifiers VTLNA Series...3 Millimeter Wave Power Amplifiers
FREQUENCY MULTIPLIERS
MULTIPLIERS A series of broadband frequency multipliers is available with output frequencies between 18 and 110 GHz. The use of GaAs diodes on a suspended substrate circuit allows an extremely compact
12B01A L- & S-Band Solid State Power Amplifier
12B1A L- & S-Band Solid State Power Amplifier 1 Watt CW 2.5 Watts Linear, 5% EVM @ 34 dbm 1. GHz - 2.5 GHz P/N: NW-PA-12B1A (includes NW-PA-ACC-CB9MA interface cable) The NuPower 12B1A is a small, highly
GaAs MMIC Power Amplifier
GaAs MMIC Power Amplifier AM83WM-BM-R AM83WM-FM-R December 214 REV DESCRIPTION AMCOM s AM83WM-BM/FM-R is an ultra broadband GaAs MMIC power amplifier. It has 23dB gain, and >28dBm output power over the.
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v.51 HMC7LP5E POWER AMPLIFIER,.2
Low Power GaAs MMIC Double Balanced Mixer. Refer to our website for a list of definitions for terminology presented in this table.
Low Power GaAs MMIC Double Balanced Mixer MM1-0212LSM 1. Device Overview 1.1 General Description The MM1-0212LSM is a low power GaAs MMIC double balanced mixer that operates at LO powers as a low as +1
FREQUENCY MULTIPLIERS
FREQUENCY MULTIPLIERS ISO 9001 REGISTERED COMPANY PASSIVE AND ACTIVE Doublers Triplers Higher-Order Products TABLE OF CONTENTS CONTENTS PAGE INTRODUCTION 2 TECHNICAL OVERVIEW 2 Technical Discussion 3 Design
MMA GHz, 0.1W Gain Block
Total Size: 172 x 76 Scribe Alley: 7 x 7 MMA-174321 Features: Frequency Range: 17 43 GHz P1dB: 21 dbm Psat: 22 dbm Gain: 22 db Vdd =5 V (3 V to 5 V) Ids = 2 ma (15mA to 3mA) Input and Output Fully Matched
SDA SMA DATA SHEET
0 to 60 db 10 Bit Programmable TTL Controlled Step Attenuator With a 006 db Step SMA Female To SMA Female From 500 MHz To 18 GHz The is a Non-Reflective 10 Bit Programmable 60 db Pin Diode Attenuator with
Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 45 ma
v2.61 Typical Applications This is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram Features Low Noise Figure: 2. db High Gain: 22 db
Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 70 ma
v2.61 Typical Applications This is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram Features Low Noise Figure: 2.5 db Gain: 13 db P1dB
RF Integrated Solutions
Power Matters. RF Integrated Solutions NEW Gallium Nitride (GaN) Amplifiers Low, Medium & High Power Amplifiers Surface Mount Amplifiers Limiting Amplifiers Equalizer Amplifiers Variable Amplifiers High
Parameter Symbol Units MIN MAX. RF Input power (CW) Pin dbm +20
AMT-A0119 0.8 GHz to 3 GHz Broadband High Power Amplifier W P1dB Data Sheet Features 0.8 GHz to 3GHz Frequency Range Class AB, High Linearity Gain db min 55 db Typical Gain Flatness < ± 1.2 db Typical
HMC5805ALS6 AMPLIFIERS - LINEAR & POWER - SMT. Typical Applications. Features. Functional Diagram
HMC585ALS6 v2.517 GaAs phemt MMIC.25 WATT POWER AMPLIFIER DC - 4 GHz Typical Applications The HMC585ALS6 is ideal for: Test Instrumentation Microwave Radio & VSAT Military & Space Telecom Infrastructure
GaAs, phemt, MMIC, Low Noise Amplifier, 0.3 GHz to 20 GHz HMC1049LP5E
ACG ACG ACG FEATURES Low noise figure:. db PdB output power:. dbm PSAT output power: 7. dbm High gain: db Output IP: 9 dbm Supply voltage: VDD = 7 V at 7 ma Ω matched input/output (I/O) -lead, mm mm LFCSP
100W Power Amplifier 8GHz~11GHz
100W Power Amplifier 8GHz~11GHz High output power +50dBm Aerospace and military application X band radar High Peak to average handle capability All specifications can be modified upon request Parameter
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v1.14 AMPLIFIER, 18-4 GHz Typical
8W Wide Band Power Amplifier 1GHz~22GHz
8W Wide Band Power Amplifier 1GHz~22GHz Features Wideband Solid State Power Amplifier Gain: 50 db Typical Psat: +39 dbm Supply Voltage: +36V Electrical Specifications, T A = +25⁰C Typical Applications
Microwave. Accessories for Microwave Scalar and System Analyzers
Microwave Accessories for Microwave Scalar and System Analyzers The following optional accessories are designed for use with the 6200B series of Microwave Test Sets, the 6820 series Scalar Analyzers and
GaAs MMIC devices are susceptible to Electrostatic Discharge. Use proper ESD precautions when handling these items.
The is a broadband, power efficient GaAs PHEMT distributed amplifier in a 4mm QFN surface mount package. The is designed to provide optimal LO drive for T3 mixers. Typically, ADM-26-2931SM provides. db
Parameter Min. Typ. Max. Min. Typ. Max. Units
25W Wide Band Power Amplifier 20-6000MHz Features Wideband Solid State Power Amplifier Psat: +45dBm Typical Gain: 50dB Typical Supply Voltage: +60V DC Electrical Specifications, T A =25 Parameter Min.
4W Ultra Wide Band Power Amplifier 0.1GHz~22GHz
4W Ultra Wide Band Power Amplifier 0.1GHz~22GHz Features Wideband Solid State Power Amplifier Gain: 40 db Typical Psat: +37 dbm Typical Noise Figure: 3dB Typical Supply Voltage: +24V (-NP) / +36V (-WP)
Datasheet SHF 100 BPP
SHF Communication Technologies AG Wilhelm-von-Siemens-Str. 23D 12277 Berlin Germany Phone ++49 30 / 772 05 10 Fax ++49 30 / 753 10 78 E-Mail: sales@shf.de Web: http://www.shf.de Datasheet SHF 100 BPP Broadband
100W Wide Band Power Amplifier 6GHz~18GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units. Frequency Range GHz Gain db
100W Wide Band Power Amplifier 6GHz~18GHz Features Wideband Solid State Power Amplifier Psat: +50dBm Gain: 75 db Typical Supply Voltage: +48V On board microprocessor driven bias controller. Electrical
Universal/Standard Ku-band GaN 40W BUC MODEL No. NJT8371 series
< Features > * GaN Technology Amplifier Inside * RF Frequency Line-up Universal Ku-band: 13.75 to 14.5 GHz Standard Ku-band: 14.0 to 14.5 GHz * High Efficiency Output Power Saturation Output Power: +46.0
GaAs phemt MMIC Low Noise Amplifier, 0.3 GHz to 20 GHz HMC1049
ACG ACG ACG FEATURES Low noise figure:. db PdB output power:. dbm PSAT output power: 7. dbm High gain: db Output IP: 9 dbm Supply voltage: VDD = 7 V at 7 ma Ω matched input/output (I/O) -lead mm mm SMT
6-18 GHz Low Phase Noise Amplifier
-1 GHz Low Phase Noise Amplifier Features Functional Block Diagram Wide bandwidth Low phase noise Low current consumption Pb-free RoHs compliant 4x4 mm SMT package Description The CMD24C4 is a wideband
Features. = +25 C, Vdd = 5V, Idd = 85 ma*
Typical Applications The is an ideal gain block or driver amplifi er for: Point-to-Point Radios Point-to-Multi-Point Radios VSAT Functional Diagram Features Saturated Power: +23 dbm @ 27% PAE Gain: db
GHz Low Noise Amplifier
8.0-12.0 GHz Low Noise Amplifier Features Frequency Range : 8.0-12.0 GHz Low Noise Figure < 1.7 db 26 db nominal gain 12 dbm P 1dB High IP3 Input Return Loss > 10 db Output Return Loss > 10 db DC decoupled