FMAM1035 DATA SHEET. 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA. Features: Applications:
|
|
- Cecilia Scott
- 6 years ago
- Views:
Transcription
1 FMAM13 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA The FMAM13 is a low phase noise amplifier that operates across the frequency range from 3 GHz to 8 GHz. The design utilizes GaAs HBT MMIC technology and exhibits ultra low phase noise of khz offset frequency. The design also exhibits high dynamic range with typical performance that incudes 11 db of small signal gain, 6 db noise figure, up to +14 dbm of output power at P1dB, +2 dbm output IP3, while using a +7V single DC supply. The wideband distributed amplifier design input/output ports are internally matched to ohms and are DC blocked. The drop-in package is hermetically sealed with field replaceable SMA connectors and has an operating temperature range of - C to +8 C. And for added confidence, this rugged package assembly is designed to meet MIL-STD-883 test conditions for Hermeticity and Temperature Cycle.. Functional Block Diagram Electrical Specifications (TA = +2 C, DC Voltage = 7Vdc, DC Current = 2mA). Description Min Typ Max Unit Features: Low Phase Noise Amplifier Wide Frequency band Highly Linear GaAs HBT MMIC Technology Phase Noise -162 dbc/ 1KHz offset Gain 11 db High Output IP3 +2 dbm P1dB up to +14 dbm Hermetically Sealed Module Mil Spec Compliant Field Replaceable SMA Connectors - C to +8 C Operating Temperature Applications: Electronic Warfare Microwave Radio VSAT Radar Space Systems Test Instrumentation Telecom Infrastructure Frequency Range 3 8 GHz Small Signal Gain 11 db Output at 1 db Compression Point +14 dbm Output 3rd Intercept Point +2 dbm Noise Figure 6 db Operating DC Voltage 7 Volts Operating DC Current 2 ma Operating Temperature Range - +8 C.. Fairview Microwave 113 Junction Dr. #1 Allen, TX 713 Tel: / (972) Fax: (972) sales@fairviewmicrowave.com REV 1. Page 1 of 6 Copyright 217
2 FMAM13 Performance by Frequency Description Min. Typ. Max. Units Frequency Range 3-8 GHz Vdc Range V Gain 9 11 db Gain Variation Over Temperature.1 db/ C Noise Figure 6 db Input Return Loss 18 db Output Return Loss 2 db Output Power For 1 db Compression (P1dB) dbm Saturated Output Power (Psat) +21 dbm Output Third Order Intercept (IP3) +2 dbm Phase 1 Hz, Psat, 6 GHz -148 dbc/hz Phase 1 KHz, Psat, 6 GHz -162 dbc/hz Phase 1 KHz, Psat, 6 GHz -168 dbc/hz Supply Current (Quiescent) 11 ma Supply Current (Under RF Drive) 2 ma Mechanical Specifications Size Length 1.14 in [28.96 mm] Width 1.9 in [48.26 mm] Height.6 in [14.22 mm]. Weight.417 lbs [189. g] Connector Option Input Connector Output Connector Field Replaceable SMA Female SMA Female Environmental Specifications Temperature Operating Range Storage Range Temperature Cycling Hermetic Seal ESD Sensitivity - to +8 deg C -6 to + deg C MIL-STD-883, Method 11C, Cond B Gross Leak MIL-STD-883 Method 114C1/Fine Leak MIL-STD-883, Method 114A2, x 1-8 atm cc ESD Sensitive Material, Transport material in Approved ESD bags. Handle only in ESD Workstation. Compliance Certifications (see product page for current document) Plotted and Other Data Notes: Values at 2 C, sea level 113 Junction Dr. #1 Allen, TX 713 Tel: / (972) / Fax: (972) REV 1. Page 2 of 6
3 FMAM13 Typical Performance Data Broadband, Gain & Return Loss Gain vs. Temperature 1 13 RESPONSE (db) S21 S11 S22 GAIN (db) Input Return Loss vs. Temperature Output Return Loss vs. Temperature - - RETURN LOSS (db) ISOLATION (db) Reverse Isolation vs. Temperature -2 Noise Figure vs. Temperature 1 8 ISOLATION (db) NOISE FIGURE (db) Junction Dr. #1 Allen, TX 713 Tel: / (972) / Fax: (972) REV 1. Page 3 of 6
4 FMAM13 Phase Noise at Pout = 1 GHz Phase Noise at Pout = GHz Phase Noise at Pout = GHz Phase Noise at Pout = 1 7 GHz Phase Noise at Pout = 7 GHz Phase Noise at Pout = 7 GHz 113 Junction Dr. #1 Allen, TX 713 Tel: / (972) / Fax: (972) REV 1. Page 4 of 6
5 FMAM13 Output P1dB vs. Temperature 2 Output Psat vs. Temperature P1dB (db) 1 P1dB (db) 1 Output IP3 vs. Temperature 3 Phase Noise at Pout = 1 3. GHz IP3 (db) Phase Noise at Pout = 3. GHz Phase Noise at Pout = 3. GHz 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA from Fairview Microwave is in-stock and available to ship same-day. All of our RF/microwave products are available off-the-shelf from our ISO 91:28 certified facilities in Allen, Texas. Fairview Microwave is RF on-demand. For additional information on this product, please click the following link: 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA FMAM13 URL: Junction Dr. #1 Allen, TX 713 Tel: / (972) / Fax: (972) REV 1. Page of 6
6 FMAM13 6 db NF Low Phase Noise Amplifier Operating From 3 GHz to 8 GHz with 11 db Gain, 14 dbm P1dB and SMA REV 1. Page 6 of 6
FMAM4032 DATA SHEET. 10 MHz to 6 GHz, Medium Power Broadband Amplifier with 900 mw, 24 db Gain and SMA. Features: Applications:
FMAM432 1 MHz to 6 GHz, Medium Power Broadband Amplifier with 9 mw, 24 db Gain and SMA FMAM432 two stage amplifier operates across a wide frequency range from 1 MHz to 6 GHz The design utilizes GaAs PHEMT
More informationFMMX9003 DATA SHEET. Field Replaceable SMA IQ Mixer From 11 GHz to 16 GHz With an IF Range From DC to 3.5 GHz And LO Power of +19 dbm.
FMMX93 Field Replaceable SMA IQ Mixer From 11 GHz to 16 GHz With an IF Range From DC to 3.5 GHz And LO Power of +19 dbm FMMX93 is an I/Q double balanced millimeter-wave mixer module that operates across
More informationSPA SMA DATA SHEET
43 db Gain Medium Power High Gain Amplifier at 3 Watt P1dB Operating From 14.4 GHz to 15.4 GHz with 41 dbm IP3 and SMA SPA-154-43-03-SMA is a 3 Watt Ku Band high gain power coaxial amplifier operating
More informationSLA SMA DATA SHEET
SLA-6-8-4-SMA 8 Gain Limiting Amplifier Operating From 2 GHz to 6 GHz with -61 to 1 Pin, 1 Psat and SMA The SLA-6-8-4-SMA is a 2 to 6 GHz high gain wide-band coaxial limiting amplifier. The model operates
More informationSDA SMA DATA SHEET
0 to 60 db 10 Bit Programmable TTL Controlled Step Attenuator With a 006 db Step SMA Female To SMA Female From 500 MHz To 18 GHz The is a Non-Reflective 10 Bit Programmable 60 db Pin Diode Attenuator with
More informationFrequency Divider, Divide by 2 Prescaler Module, 500 MHz to 18 GHz, Field Replaceable SMA
Features Divide by 2 Prescaler Wide Frequency Band GaAs HBT MMIC Technology Low Phase Noise -15 dbc/hz @ 1 khz offset Output Power -4 dbm Low Reverse Leakage Level 55 db typical Applications Electronic
More informationFMAM5032 DATA SHEET. 48 db Gain High Power High Gain Amplifier at 50 Watt Psat Operating From 500 MHz to 3 GHz with 52 dbm IP3 and SMA.
48 Gain High Power High Gain Amplifier at 50 Watt Psat Operating From 500 MHz to 3 GHz with 52 m IP3 and SMA FMAM5032 is a high gain Class A/AB GaN Linear Power Amplifier operating in the 500 to 3000 MHz
More informationFMSW6124 DATA SHEET. Transfer Latching Electro-Mechanical Relay Switch From DC to 40 GHz, 5 Watts with Indicators, TTL, Self Cut Off, Diodes, 2.
Transfer Latching Electro-Mechanical Relay Switch From DC to 40 GHz, 5 Watts with Indicators, TTL, Self Cut Off, Diodes, 2.92mm The FMSW6124 is a Transfer Electromechanical Relay Switch that operates over
More informationFMSW6097 DATA SHEET. SPDT Failsafe Electro-Mechanical Relay Switch From DC to 26.5 GHz, 20 Watts with TTL, Diodes, Indicators, SMA.
SPDT Failsafe Electro-Mechanical Relay Switch From DC to 26.5 GHz, 20 Watts with TTL, Diodes, Indicators, SMA The FMSW6097 is an SPDT Electromechanical Relay Switch that operates over a wide frequency
More informationFMSW6129 DATA SHEET. SP4T Normally Open Electro-Mechanical Relay Switch From DC to 22 GHz, 20 Watts with Indicators, TTL, Diodes, SMA.
SP4T Normally Open Electro-Mechanical Relay Switch From DC to 22 GHz, 20 Watts with Indicators, TTL, Diodes, SMA The FMSW6129 is an SP4T Electromechanical Relay Switch that operates over a wide frequency
More informationSEMS-4079-SP8T-SMA DATA SHEET
SP8T Latching Electro-Mechanical Relay Switch From DC to 18 GHz, 100 Watts with Self Cut Off, Auto Reset, Indicators, Diodes, SMA The SEMS-4079-SP8T-SMA is an SP8T Terminated Electromechanical Relay Switch
More informationFMSN3902 DATA SHEET. USB Frequency Synthesizer PLL (Phase Locked Loop), Operating From 5 GHz to 10 GHz With SMA Output. Features: Applications:
USB Frequency Synthesizer PLL (Phase Locked Loop), Operating From 5 GHz to 10 GHz With SMA Output FMSN3902 is a Frequency Synthesizer Module that covers a wide frequency band from 5 GHz to 10 GHz with
More informationFeatures. = +25 C, Vdc = +7V
amplifiers Typical Applications The is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram Features Ultra Low Phase Noise: -7 dbc/hz @ khz Noise Figure: 6 db Gain:
More informationSA26B-10 DATA SHEET. 10 db Fixed Attenuator SMA Male To SMA Female Up To 26 GHz Rated To 2 Watts With Passivated Stainless Steel Body.
10 db Fixed Attenuator SMA Male To SMA Female Up To 26 GHz Rated To 2 Watts With Passivated Stainless Steel Body Fairview Microwave carries a broad selection of fixed attenuators with a wide range of attenuation
More informationSA18N-20 DATA SHEET. 20 db Fixed Attenuator N Male To N Female Up To 18 GHz Rated To 2 Watts With Passivated Stainless Steel Body.
20 db Fixed Attenuator N Male To N Female Up To 18 GHz Rated To 2 Watts With Passivated Stainless Steel Body Fairview Microwave carries a broad selection of fixed attenuators with a wide range of attenuation
More informationFeatures. The HMC-C072 is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT. = +25 C, Vdc = +7V
amplifiers Typical Applications The is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram Features Ultra Low Phase Noise: -67 dbc/hz @ khz Noise Figure: 4.5 db Gain:
More informationFeatures. = +25 C, +Vdc = +6V, -Vdc = -5V
v3.7 WIDEBAND LNA MODULE, - 2 GHz amplifiers Typical Applications The Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Industrial Sensors Functional
More informationFeatures. = +25 C, Vdc = +5V
amplifiers Typical Applications The HMC-C is ideal for: Microwave Radio Military & Space Test Instrumentation VSAT Functional Diagram v.7 HMC-C Features Ultra Low Phase Noise: -6 dbc/hz @ khz Noise Figure:
More informationSC6015 DATA SHEET. BNC Female Bulkhead Connector Crimp/Solder Attachment For.100 inch, RG316, RG174, RG188, LMR-100, LMR-100A, LMR-100-FR Cable
BNC Female Bulkhead Connector Crimp/Solder Attachment For 100 inch, RG316, RG174, RG188, LMR-100, LMR-100A, LMR-100-FR Cable BNC female bulkhead connector with crimp/solder attachment for 100 inch, RG316,
More informationFeatures. = +25 C, +Vdc = +6V, -Vdc = -5V
HMC-C59 v.59 WIDEBAND LNA MODULE, - 2 GHz Typical Applications The HMC-C59 Wideband LNA is ideal for: Telecom Infrastructure Features Noise Figure:.8 db @ 8 GHz High Gain: 6 db @ 8 GHz PdB Output Power:
More informationFeatures. = +25 C, Vs= +8V to +16V
v2.17 Typical Applications The Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Features Electrical Specifications,
More informationFeatures. Gain Variation Over Temperature db/ C
HMC-C26 Features Typical Applications The HMC-C26 Wideband PA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Gain: 3 db
More informationFeatures. = +25 C, Vdd = 5V
v3.117 HMC1LH5 Typical Applications The HMC1LH5 is a medium PA for: Telecom Infrastructure Military Radio, Radar & ECM Space Systems Test Instrumentation Functional Diagram Features Gain: 5 db Saturated
More informationFMPB1002 DATA SHEET. Coaxial RF GS Probe with 800 Micron Pitch Up to 20 GHz with 3.5mm Interface and Cable Mount. Configuration: Features:
Coaxial RF GS Probe with 800 Micron Pitch Up to 20 GHz with 3.5mm Interface and Cable Mount Coaxial RF GS probe, part number FMPB1002, from Fairview Microwave is in-stock and ships same day. This probe
More informationDC-20 GHz Distributed Driver Amplifier. Parameter Min Typ Max Min Typ Max Units
7-3 RF-LAMBDA DC-20 GHz Distributed Driver Amplifier Electrical Specifications, T A =25 Features Ultra wideband performance Positive gain slope High output power Low noise figure Microwave radio and VSAT
More informationFeatures. Output Power for 1 db Compression (P1dB) dbm Saturated Output Power (Psat) dbm
v1.314 Typical Applications Features The is ideal for: Test Instrumentation Microwave Radio & VSAT Telecom Infrastructure Military & Space Fiber optics Functional Diagram P1dB Output Power: +27 dbm Psat
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Electrical Specifications, T A =25 Ultra Wide Band Low Noise Amplifier AC 110V/220V 0.01-20GHz Parameters Min. Typ. Max. Min. Typ. Max. Units Frequency Range 0.01 10 10 20 GHz Gain 28 30 26 28 db Gain
More informationFeatures. Gain: 17 db. OIP3: 25 dbm. = +25 C, Vdd 1, 2 = +3V
v.7 HMCLC Typical Applications The HMCLC is ideal for use as a LNA or driver amplifier for: Point-to-Point Radios Point-to-Multi-Point Radios & VSAT Test Equipment and Sensors Military & Space Functional
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Ultra Wide Band Low Noise Amplifier 0.01GHz~10GHz Electrical Specifications, TA = 25, Vcc = 12V Features Gain: 28dB Typical Noise Figure: 2.5dB Typical High P1dB: 15dBm Typical Supply Voltage: 12V Parameter
More informationFeatures = +5V. = +25 C, Vdd 1. = Vdd 2
v7.11 HMC1LC3 POWER AMPLIFIER, - GHz Typical Applications The HMC1LC3 is ideal for use as a medium power amplifier for: Microwave Radio & VSAT Military & Space Test Equipment & Sensors Fiber Optics LO
More informationHMC326MS8G / 326MS8GE
v9.511 AMPLIFIER, 3. - 4.5 GHz Typical Applications The HMC326MS8G / HMC326MS8GE is ideal for: Microwave Radios Broadband Radio Systems Wireless Local Loop Driver Amplifier Functional Diagram Features
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v.51 HMC7LP5E POWER AMPLIFIER,.2
More information5W Ultra Wide Band Power Amplifier 2-18GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units
7-3 RF-LAMBDA 5W Ultra Wide Band Power Amplifier 2-18GHz Features Wideband Solid State Power Amplifier Psat: + 37dBm Gain: 35 db Supply Voltage: +24V Electrical Specifications, T A = +25⁰C, Vcc = +24V
More informationFeatures. = +25 C, Vdd= 5V, Vgg2= Open, Idd= 60 ma*
v.7 HMCLH AGC AMPLIFIER, - GHz Typical Applications The HMCLH is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C I Test Instrumentation Fiber Optics Functional Diagram Features
More informationFeatures. = +25 C, Vdd= 8V, Vgg2= 3V, Idd= 290 ma [1]
Typical Applications The is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C 3 I Test Instrumentation Fiber Optics Functional Diagram Features P1dB Output Power: + dbm Gain:
More information4W Ultra Wide Band Power Amplifier 0.1GHz~22GHz
4W Ultra Wide Band Power Amplifier 0.1GHz~22GHz Features Wideband Solid State Power Amplifier Gain: 40 db Typical Psat: +37 dbm Typical Noise Figure: 3dB Typical Supply Voltage: +24V (-NP) / +36V (-WP)
More informationFeatures. = +25 C, Vdd= 8V, Idd= 75 ma*
HMC46LC5 Typical Applications v3.11 AMPLIFIER, DC - 2 GHz Features The HMC46LC5 is ideal for: Noise Figure: 2.5 db @ 1 GHz Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation
More informationFeatures. = +25 C, Vdd= 5V. Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units. Frequency Range GHz
Typical Applications The HMC62LP / HMC62LPE Wideband LNA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military EW, ECM & C 3 I Test Instrumentation Fiber Optics Functional Diagram Features
More informationFeatures. = +25 C, Vdd= +12V, Vgg2= +5V, Idd= 400 ma*
Typical Applications The HMC637LP5(E) wideband PA is ideal for: Features P1dB Output Power: +29 dbm Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v3.38 POWER AMPLIFIER, 2-2 GHz Typical
More informationFeatures. Parameter Min Typ. Max Min Typ. Max Min Typ Max Units Frequency Range GHz Gain
Typical Applications The HMC82LP4E is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios VSAT & SATCOM Marine Radar Military EW & ECM Functional Diagram Features High Saturated Output Power:
More informationHMC659LC5 LINEAR & POWER AMPLIFIERS - SMT. GaAs PHEMT MMIC POWER AMPLIFIER, DC - 15 GHz. Features. Typical Applications. General Description
v.61 Typical Applications The wideband PA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Features P1dB Output Power: +27.5
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Ultra Wide Band Power Amplifier 0.7GHz ~ 6GHz Features Gain: 35dB typical Output power 38dBm typical High P1dB: 35 dbm Full Band Supply Voltage: 28V 50 Ohm Matched Electrical Specifications, T A = 25⁰C,
More information30W Solid State High Power Amplifier 2-6 GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units
7-3 RF-LAMBDA 30W Solid State High Power Amplifier 2-6 GHz Features Wideband Solid State Power Amplifier Psat: +45dBm Gain: 50dB Supply Voltage: +36V Electrical Specifications, T A = +25⁰C, Vcc = +36V
More informationFeatures. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2]
Typical Applications This is ideal for: Features Low Noise Figure: 1.8 db Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram High Gain: 19 db High
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v2.65 HMC455LP3 / 455LP3E Typical
More informationHMC618ALP3E AMPLIFIERS - LOW NOISE - SMT. GaAs SMT phemt LOW NOISE AMPLIFIER, GHz. Typical Applications. Features. Functional Diagram
7 Typical Applications The is ideal for: Cellular/3G and LTE/WiMAX/4G BTS & Infrastructure Repeaters and Femto Cells Public Safety Radios Functional Diagram v. Electrical Specifications T A = + C, Rbias
More information8W Wide Band Power Amplifier 1GHz~22GHz
8W Wide Band Power Amplifier 1GHz~22GHz Features Wideband Solid State Power Amplifier Gain: 50 db Typical Psat: +39 dbm Supply Voltage: +36V Electrical Specifications, T A = +25⁰C Typical Applications
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Ultra Wide Band Low Noise Amplifier 0.01GHz~30GHz Electrical Specifications, TA = 25⁰C Features Gain: 36 Typical Noise Figure: 3.5 Typical P1 Output Power: 28m Typical Supply Voltage: AC110V~220V Typical
More information100W Power Amplifier 8GHz~11GHz
100W Power Amplifier 8GHz~11GHz High output power +50dBm Aerospace and military application X band radar High Peak to average handle capability All specifications can be modified upon request Parameter
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Ultra Wide Band Low Noise Amplifier AC 1V/2V 0.0~ Electrical Specifications, T A =2 Parameters Min. Typ. Max. Min. Typ. Max. Units Frequency Range 0.01 1 1 3 GHz Gain 33 36 33 36 db Gain Flatness ±1. ±1.0
More informationFeatures. = +25 C, Vdd =+28V, Idd = 850 ma [1]
v1.413 HMC87F POWER AMPLIFIER, 2 - GHz Typical Applications The HMC86F is ideal for Test Instrumentation General Communications Radar Functional Diagram Features High Psat: +38. dbm Power Gain at Psat:
More informationUltra Wide Band Low Noise Amplifier GHz. Electrical Specifications, TA = +25⁰C, With Vg= -5V, Vcc = +4V ~ +7V, 50 Ohm System
Ultra Wide Band Low Noise Amplifier 0.5 46GHz Parameter Min. Typ. Max. Min. Typ. Max. Units Frequency Range 0.5 20 20 46 GHz Gain 13 13 db Gain Variation Over Temperature (-45 ~ +85) ±3 ±2 db Noise Figure
More informationOBSOLETE HMC5846LS6 AMPLIFIERS - LINEAR & POWER - SMT. Electrical Specifications, T A. Features. Typical Applications. General Description
v1.414 Typical Applications The HMC846LS6 is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios VSAT & SATCOM Military & Space Functional Diagram Electrical Specifications, T A = +2 C Vdd = Vdd1,
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v.51 HMC32LC Typical Applications
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v1.414 Typical Applications The HMC5846LS6
More informationFeatures. = +25 C, Vdd 1, 2, 3 = +3V
v.11 HMC6LC AMPLIFIER, 6-2 GHz Typical Applications The HMC6LC is ideal for use as a LNA or driver amplifier for: Point-to-Point Radios Point-to-Multi-Point Radios & VSAT Test Equipment and Sensors Military
More information30W Wideband Solid State Power Amplifier 6-12GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units
7-3 RF-LAMBDA 30W Wideband Solid State Power Amplifier 6-12GHz Electrical Specifications, TA = +25⁰C, Vdd = +36V Parameter Min. Typ. Max. Min. Typ. Max. Units Frequency Range 6 9 10 12 GHz Gain 60 55 db
More informationHMC997LC4. Variable Gain Amplifier - SMT. VARIABLE GAIN AMPLIFIER GHz. Typical Applications. General Description. Functional Diagram
v2.14 Typical Applications The is ideal for: Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM Subsystems Ka-Band Radar Test Equipment Functional Diagram Features Wide Gain Control Range: 1 db Single
More informationFeatures. = +25 C, Vcc = +5.0V. Vcc = +5V Parameter
Typical Applications Ideal as a Driver & Amplifier for: 2.2-2.7 GHz MMDS 3. GHz Wireless Local Loop - 6 GHz UNII & HiperLAN Functional Diagram Features P1dB Output Power: +14 dbm Output IP3: +27 dbm Gain:
More informationTEL: FAX: v.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER, GHz Broadband Gain & Return Vdd =
TEL:7-339622 FAX:7-337612 E-MAIL: szss@3.com v.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER,. - 3. GHz Typical Applications Broadband or Narrow Band Applications: Cellular/PCS/3G Fixed Wireless
More information100W Wide Band Power Amplifier 6GHz~18GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units. Frequency Range GHz Gain db
100W Wide Band Power Amplifier 6GHz~18GHz Features Wideband Solid State Power Amplifier Psat: +50dBm Gain: 75 db Typical Supply Voltage: +48V On board microprocessor driven bias controller. Electrical
More informationFeatures = +5V. = +25 C, Vdd 1. = Vdd 2
v1.11 HMC51LP3 / 51LP3E POWER AMPLIFIER, 5-1 GHz Typical Applications The HMC51LP3(E) is ideal for: Microwave Radio & VSAT Military & Space Test Equipment & Sensors Fiber Optics LO Driver for HMC Mixers
More informationHMC694LP4 / 694LP4E. Variable gain amplifiers - ANALOG - smt. GaAs MMIC ANALOG VARIABLE GAIN AMPLIFIER, 6-17 GHz. Typical Applications
v2.1 Typical Applications The HMC694LP4(E) is ideal for: Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM X-Band Radar Test Equipment Features Wide Gain Control Range: 23 db Single Control Voltage
More information2 GHz to 6 GHz, 500 W Power Amplifier HMC8113
Data Sheet FEATURES 2 GHz to 6 GHz frequency range 85 db typical small signal gain 57 dbm typical saturated output power 61 db gain control range with 1 db LSB Standard 5U 19-inch rack chassis (per EIA-310D)
More informationFeatures. = +25 C, Vdd = +10 V, Idd = 350 ma
HMC97APME v2.4 POWER AMPLIFIER,.2-22 GHz Typical Applications The HMC97APME is ideal for: Test Instrumentation Military & Space Functional Diagram Features High P1dB Output Power: + dbm High : 14 db High
More informationParameter Min. Typ. Max. Min. Typ. Max. Units
Electrical Specifications, TA = 25 C, With Vcc = 12V, 50 Ohm System Feature Gain: 36 db Noise Figure: 3.0dB P1dB Output Power: 10dB m full band Supply Voltage: 12V @185mA 50 Ohm Matched Input / Output
More informationMonolithic Amplifier CMA-84+ Wideband, High Dynamic Range, Ceramic. DC to 7 GHz. The Big Deal
Wideband, High Dynamic Range, Ceramic Monolithic Amplifier 50Ω DC to 7 GHz The Big Deal Ceramic, hermetically sealed, nitrogen filled Low profile case, 0.045 High IP3, +38 dbm High Gain, 24 db High POUT,
More informationGain Control Range db
v1.112-12 GHz Typical Applications The is ideal for: Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM Subsystems X-Band Radar Test Equipment & Sensors Functional Diagram Features Wide Gain Control
More information6-18 GHz Low Phase Noise Amplifier
-1 GHz Low Phase Noise Amplifier Features Functional Block Diagram Wide bandwidth Low phase noise Low current consumption Pb-free RoHs compliant 4x4 mm SMT package Description The CMD24C4 is a wideband
More informationParameter Symbol Units MIN MAX. RF Input power (CW) Pin dbm +20
AMT-A0119 0.8 GHz to 3 GHz Broadband High Power Amplifier W P1dB Data Sheet Features 0.8 GHz to 3GHz Frequency Range Class AB, High Linearity Gain db min 55 db Typical Gain Flatness < ± 1.2 db Typical
More informationGHz Low Noise Amplifier
8.0-12.0 GHz Low Noise Amplifier Features Frequency Range : 8.0-12.0 GHz Low Noise Figure < 1.7 db 26 db nominal gain 12 dbm P 1dB High IP3 Input Return Loss > 10 db Output Return Loss > 10 db DC decoupled
More informationFeatures. Parameter Min Typ. Max Min Typ. Max Min Typ Max Units Frequency Range GHz Gain
Typical Applications The is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios VSAT & SATCOM Marine Radar Military EW & ECM Functional Diagram Features High Saturated Output Power: dbm @ % PAE
More informationHMC454ST89 / 454ST89E. Features. = +25 C, Vs= +5V [1]
Typical Applications The HMC44ST8 / HMC44ST8E is ideal for applications requiring a high dynamic range amplifi er: GSM, GPRS & EDGE CDMA & W-CDMA CATV/Cable Modem Fixed Wireless & WLL Features Output IP3:
More informationHMC1040LP3CE. Amplifiers - Low Noise - smt. GaAs phemt MMIC LOW NOISE AMPLIFIER, GHz. Features. Typical Applications. General Description
v.112 HMC14LP3CE AMPLIFIER, 24-43. GHz Typical Applications This HMC14LP3BE is ideal for: Point-to-Point Radios Test Instrumentation SatCom Transponders & VSAT Industrial Sensors EW & ECM Subsystems Functional
More informationParameter Min. Typ. Max. Min. Typ. Max. Units
25W Wide Band Power Amplifier 20-6000MHz Features Wideband Solid State Power Amplifier Psat: +45dBm Typical Gain: 50dB Typical Supply Voltage: +60V DC Electrical Specifications, T A =25 Parameter Min.
More information2 GHz to 28 GHz, GaAs phemt MMIC Low Noise Amplifier HMC7950
Data Sheet FEATURES Output power for db compression (PdB): 6 dbm typical Saturated output power (PSAT): 9. dbm typical Gain: db typical Noise figure:. db typical Output third-order intercept (IP3): 6 dbm
More information150W Solid State Broadband EMC Benchtop Power Amplifier 6-18GHz. Parameter Min Typ Max Min Typ Max Units
7-3 RF-LAMBDA 150W Solid State Broadband EMC Benchtop Power Amplifier 6-18GHz Electrical Specifications, T A =25 Voltage = 110v/220v AC Features High Saturated Output Power 50~52dBm. Telecom Infrastructure
More informationHMC998. Amplifiers - Linear & Power - Chip. GaAs phemt MMIC 2 WATT POWER AMPLIFIER, GHz. Electrical Specifications, T A.
v1.811 2 WATT POWER AMPLIFIER,.1-22 GHz Typical Applications Features The is ideal for: Test Instrumentation Microwave Radio & VSAT Military & Space Telecom Infrastructure Fiber Optics Functional Diagram
More informationFeatures. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 70 ma
v2.61 Typical Applications This is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram Features Low Noise Figure: 2.5 db Gain: 13 db P1dB
More informationFeatures. = +25 C, Vdc = +12V
Typical Applications The VCO Module is ideal for: Industrial/Medical Equipment Test & Measurement Equipment Military Radar, EW & ECM Lab Instrumentation Functional Diagram Electrical Specifications, T
More informationFeatures. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 45 ma
v2.61 Typical Applications This is ideal for: Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram Features Low Noise Figure: 2. db High Gain: 22 db
More informationCHA5294 RoHS COMPLIANT
30-40GHz Medium Power Amplifier GaAs Monolithic Microwave IC CHA5294 RoHS COMPLIANT Description The CHA5294 is a high gain four-stage monolithic medium power amplifier. It is designed for a wide range
More information30 MHz to 6 GHz RF/IF Gain Block ADL5544
Data Sheet FEATURES Fixed gain of 17.4 db Broadband operation from 3 MHz to 6 GHz Input/output internally matched to Ω Integrated bias control circuit OIP3 of 34.9 dbm at 9 MHz P1dB of 17.6 dbm at 9 MHz
More informationHMC454ST89 / 454ST89E
HMC44ST8 / 44ST8E Typical Applications The HMC44ST8 / HMC44ST8E is ideal for applications requiring a high dynamic range amplifi er: GSM, GPRS & EDGE CDMA & W-CDMA CATV/Cable Modem Fixed Wireless & WLL
More informationRF Integrated Solutions
Power Matters. RF Integrated Solutions NEW Gallium Nitride (GaN) Amplifiers Low, Medium & High Power Amplifiers Surface Mount Amplifiers Limiting Amplifiers Equalizer Amplifiers Variable Amplifiers High
More informationFeatures OBSOLETE. = +25 C, as a function of Vdd. Vdd = +3V Vdd = +5V Vdd = +5V Vdd = +5V Parameter
v5.117 HMC3 / 3E GENERAL PURPOSE 1 mw GaAs MMIC AMPLIFIER,. - 3. GHz Typical Applications Broadband or Narrow Band Applications: Cellular/PCS/3G Fixed Wireless & Telematics Cable Modem Termination Systems
More informationFeatures. = +25 C, Vcc =5V, Vpd = 5V. Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max Units
v2.917 Typical Applications Features The is ideal for: Point-to-Point Radios Point-to-Multipoint Radios VSAT LO Driver for HMC Mixers Military EW & ECM Functional Diagram High Output IP3: +28 dbm Single
More informationFeatures. = +25 C, Vcc = 5V, Vpd = 5V. Parameter Min. Typ. Max. Min. Typ. Max. Units
v2.717 MMIC AMPLIFIER, 4 - GHz Typical Applications The is ideal for: Cellular / PCS / 3G Fixed Wireless & WLAN CATV, Cable Modem & DBS Microwave Radio & Test Equipment IF & RF Applications Functional
More informationRF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
Wide Band High Power Solid State Power Amplifier 2GHz~6GHz Electrical Specifications, TA = +25⁰C, Vcc = +28V Features Gain: 42 db min Output power +47dBm typical High P1dB: +45dB m Full Band Supply Voltage:
More information20W Solid State Power Amplifier 26.2GHz~34GHz. Parameter Min. Typ. Max. Min. Typ. Max. Units. Frequency Range GHz.
20W Solid State Power Amplifier 26.2GHz~34GHz Features Wideband Solid State Power Amplifier Gain: 65dB Typical Psat: +43dBm Typical Supply : +24V Electrical Specifications, T A = +25⁰C, Vcc = +24V Typical
More informationFeatures. = +25 C, Vdd = +7V, Idd = 1340 ma [1]
Typical Applications The HMC591LP5 / HMC591LP5E is ideal for use as a power amplifi er for: Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment & Sensors Military End-Use Space Features Saturated
More informationFeatures. = +25 C, Vdd1, 2, 3 = 5V, Idd = 250 ma*
v.4 HMC498LC4 Typical Applications Features The HMC498LC4 is ideal for use as a LNA or Driver amplifier for: Point-to-Point Radios Point-to-Multi-Point Radios & VSAT Test Equipment & Sensors Military End-Use
More informationParameter Symbol Units MIN MAX. RF Input power (CW) Pin dbm +10
AMT-A0091 0.01 GHz to 6 GHz Broadband Low Noise Medium Power Amplifier Data Sheet Features 0.01 GHz to 6 GHz Frequency Range Typical Noise Figure < 1.2 db Typical Gain 45 db Gain Flatness < ± 1.2 db +20
More information20 GHz to 44 GHz, GaAs, phemt, MMIC, Low Noise Amplifier HMC1040CHIPS
Data Sheet FEATURES Low noise figure: 2 db typical High gain: 25. db typical P1dB output power: 13.5 dbm, 2 GHz to GHz High output IP3: 25.5 dbm typical Die size: 1.39 mm 1..2 mm APPLICATIONS Software
More informationBROADBAND DISTRIBUTED AMPLIFIER
ADM1-26PA The ADM1-26PA is a complete LO driver solution for use with all Marki mixers up to 26. GHz. This single-stage packaged GaAs MMIC distributed amplifier integrates all required biasing circuitry.
More informationFeatures. = +25 C, Vs = +5V, Vpd = +5V, Vbias=+5V
v4.1217 HMC49LP4E Typical Applications This amplifier is ideal for use as a power amplifier for 3.3-3.8 GHz applications: WiMAX 82.16 Fixed Wireless Access Wireless Local Loop Functional Diagram Features
More informationHMC639ST89 / 639ST89E
Typical Applications The HMC39ST9(E) is ideal for: Cellular / PCS / 3G WiMAX, WiBro, & Fixed Wireless CATV & Cable Modem Microwave Radio IF and RF Sections Functional Diagram Electrical Specifications,
More informationFeatures. = +25 C, Vdd = +5V, Idd = 63 ma
v2.213 LOW NOISE AMPLIFIER, 2-2 GHz Typical Applications Features The is ideal for: Test Instrumentation Microwave Radio & VSAT Military & Space Telecom Infrastructure Fiber Optics Functional Diagram Noise
More informationMilitary Amplified GPS Technical Product Data
MIL-AL D C B S 1 X Military Amplified GPS Technical Product Data Features Amplifier Gain 22dB typical Passes all GNSS Frequencies (Entire L-band Extremely Flat Group Delay Less than 1ns variation Military
More information