PT8A2511 Toaster Controller
|
|
- Lindsey Short
- 6 years ago
- Views:
Transcription
1 P PT8A2511PE PT8A2511 Features Defrost mode for frozen bread Reheat mode Operating voltage: 3.5~5.5V Few external components DIP-8 and SOIC-8 package Description The PT8A2511 is a CMOS LSI chip designed for toaster. Besides normal heating, it also provides defrost and reheat work modes. It provides low cost solution for toaster. Applications Toaster Pin Configuration DEFROST 1 8 GND 2 7 CX RELAY 3 6 Vcc 4 5 RX Pin Description DIP-8 and SOIC-8 (Top View) Top view Name Pin No. Type Description DEFROST 1 I/O 2 I/O RELAY 3 O RELAY drive output. High active. Vcc 4 - Power supply As input, requires a negative pulse to active "Defrost" function. As output, gives a "Defrost" function indicator As input, requires a negative pulse to active "Reheat" function. As output, gives a "Reheat" function indicator RX 5 O Shorts to VCC once an active negative pulse appears at Reheat 6 I/O Oscillator input/output, oscillator's Frequency of 1024Hz with an external R1,C1 CX 7 O Shorts to GND once an active negative pulse appears at Defrost GND 8 - Power Ground 1
2 Block Diagram V CC DEFROST Controller RX CX Power On Reset system oscillator Frequency divider RELAY 2
3 Maximum Ratings Storage Temperature o C to +125 o C Ambient Temperature with Power Applied... 0 o C to +85 o C Supply Voltage to Ground Potential (Inputs & V CC Only) to +5.5V Supply Voltage to Ground Potential (Outputs & D/O Only) to +5.5V DC Input Voltage to +5.5V DC Output Current...20mA Power Dissipation mW Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended operation conditions Symbol Description Min Type Max Unit T A Operation Temperature C V CC Supply voltage V V IH Input High Voltage 0.8V CC - 0 V V IL Input Low Voltage V CC V Electrical Characteristics (T A = 0 ~ 85ºC, unless otherwise noted) Symbol Description Test Conditions Min Type Max Unit V IL I OH I OL Input High Voltage Output Source Current Output Sink Current PIN: DEFROST, PIN: DEFROST, PIN: DEFROST, I OH Output Source Current PIN: RELAY I OL Output Sink Current PIN: RELAY I IH I IL I CC Input High Leakage Current Input Low Leakage Current Frequency of normal oscillator Power supply Current - - V CC =4.0V V V OH =3.0V V OL =0.5V V OH =2.0V V OL =0.5V V CC =4.0V V IH =3.5V V CC =4.0V V IL =0.5V ma ma ma ma µa µa V CC =4.0V, R1=56kΩ, C1= Hz V CC =4.0V, R1=56kΩ, C1=223, all output floating µa 3
4 Application Circuit VCC CONTROL BOARD R1 D2 HEATER R16 R2 R14 R17 R12 C3 47UF VZ1 3.9V 240 R5 1N4007 C1 220UF/16V R8 SLOT1 SLOT2 R9 R15 R10 DEFROST R11 R DFROST SW1 1 SW2 2 R3 2K 3 VCC 4 R4 TEM NTC PT8A2511P DFROST RELAY VCC R6 250k GND CX RX R C2 C R7 56k D1 1N4148 CANCEL SW3 Q1 L LEVER S1 It's better to make C2 less than 563 and R7 larger than 30k 220V 4
5 Mechanical Information PE (DIP-8) 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-001D/BA Symbol Dimensions In Millimeters Min Max A A A B B BSC c D E E e BSC L E
6 WE (SOIC-8) 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012E/AA Symbol Dimensions In Millimeters Min Max A A A b c D E E e 1.27 BSC L θ 0 8 Ordering Information Part No. Package Code Package PT8A2511PE P Lead free 8-pin DIP PT8A2511WE W Lead free and Green 8-pin SOIC E = Pb-free or Pb-free and Green Adding X Suffix= Tape/Reel Pericom Semiconductor Corporation Pericom Technology Incorporation reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom Technology does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom Technology product. The company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom Technology Incorporation. 6
O FF G ATE C LK PT8A324 4/5/6/7. 1 NTC1 NTC1 I I NTC voltage input, NTC open detection input.
Features Description Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Direct drive SCR Auto Heating off after heating timer timeout Low
More informationDescription O FF G ATE C LK PT8A323 4/5/6/7. 1 NTC1 NTC1 I I NTC voltage input, NTC open detection input.
Features Description Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Direct drive SCR Auto Heating off after heating timer timeout Low
More informationDEFROST and REHEAT key interlock each other, and BEGAL key is individual. Output driver. Key scan. System Oscillator.
PT8A5A Features Operating voltage:.5v~5.5v. Have Defrost, eheat and Bagel function elay output disable without external oscillator Adjustable timer: 0s~0mins Few external components Low cost 8-Pin DIP
More informationPT8A3270/1/2/3/4/5/6/7 Heating Controller
Features Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Proportional control Pulse trigger for high current SCR Internal Zener Auto Heating
More informationPT8A3514/15/16/17/18/19(A/B) Smart Iron Controller
Features Build in RC oscillator for sensor signal detection On chip shunt regulated power supply Using AC 0Hz/0Hz as timer clock can select by Part No. Accurate timer with error dropping in ±% Sensitive
More informationPT8A3252/54 5LED Ceramic Heating Controller
Features Pulse trigger with high current for SCR Quickly Heating-Up and Quickly Lost-Heat- Recover External Adjustable to fit wide range heating plates External Adjustable to different TCR of sensors Full
More informationPT8A3289x/3299x Heating Controller
Features Dual Voltage (120/240V) operations Internal 5V Zener Auto temperature control with NTC NTC open protection Multi mode LED indicator Pulse trigger for high current SCR/TRIAC Auto Heating off after
More informationPT7C4511. PLL Clock Multiplier. Features. Description. Pin Configuration. Pin Description
Features Zero ppm multiplication error Input crystal frequency of 5-30 MHz Input clock frequency of - 50 MHz Output clock frequencies up to 200 MHz Peak to Peak Jitter less than 200ps over 200ns interval
More informationPT8A2767x DC Motor Controller
Features Operation Range:.6~5.5V 0µA Maximum Standby Supply Current Thermal and Short-Circuit Protection Less than 00mΩ High-side MOSFET Filter for key input.5a current driver Protection for over temperature
More informationPT7M1818/1813 Supervisory Circuit
Features Highly accurate: 1.5% (25 C) Accurate power monitoring: 2.5V, 2.9V, 3. (PT7M1818), and 4.1, 4.3, 4.6V (PT7M1813) Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C
More informationDescription. This Clock Multiplier is the most cost-effective way to Input crystal frequency of 5-40 MHz
PT7C4512 Features Description Zero ppm multiplication error This Clock Multiplier is the most cost-effective way to Input crystal frequency of 5-40 MHz generate a high quality, high frequency clock outputs
More informationBCT5511 Toaster Controller
General is designed for toaster applications. It is basically a timer, setting by external RC components, to stop heating of toaster. Besides normal timer, it also has defrost and reheat functions. It
More informationPI5A23159 Low Voltage Dual SPDT 0.8Ω Analog Switch
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.8 at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Overvoltage Tolerance: 5.5V(Min) Fast Transition Speed:
More informationPI6ULS5V9509 Level Translating I 2 C-Bus/SMBus Repeater with Tiny Package
Features Bidirectional buffer isolates capacitance and allows 400 pf on port B of the device Port A operating supply voltage range of 1.1 V to V CC(B) - 1.0V Port B operating supply voltage range of 2.5
More informationPT7C4502 PLL Clock Multiplier
Features Low cost frequency multiplier Zero ppm multiplication error Input crystal frequency of 5-30 MHz Input clock frequency of 4-50 MHz Output clock frequencies up to 180 MHz Period jitter 50ps (100~180MHz)
More informationData Sheet PT8A2611/2621 PIR Sensor Light Switch Controller. Features. General Description. Function Comparison. Ordering Information.
Features General Description 2-stage operational amplifier as filter Built-in noise rejection circuit On-chip regulator Override function (PT8A2621 only) Synchronous with AC 220V/50Hz and 110V/60Hz Pulse
More informationPI5A3158B Low Voltage Dual SPDT Analog Switch 2:1 Mux/Demux Bus Switch
2:1 Mux/Demux Bus Switch Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 8Ω at 3.0 Wide Range: 1.65 to 5.5 Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5(Min)
More informationPI6C4511. PLL Clock Multiplier. Features. Description. Block Diagram. PLL Clock Synthesis and Control Circuit. Output Buffer. Crystal Oscillator
Features ÎÎZero ppm multiplication error ÎÎInput crystal frequency range: 5-30MHz ÎÎInput clock frequency range: 2-50MHz ÎÎOutput clock frequencies up to 200MHz ÎÎPeriod jitter 150ps ÎÎ9 selectable frequencies
More informationPT7M6315US. Pin Configuration PT7M6315USxxD3F/D4F. Pin Description
Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5 in 100m increments Operating voltage range: 1.0 ~ 5.5 Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:
More informationPT7M CL/CH /NL Voltage Detector
PT7M6218-6250CL/CH /NL Features Highly precision: ±1.5% (25 C); ±2.5%(-40 C to +85 C ); Low power consumption: 1.0μA @ 3.6V Vcc Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range:
More informationPI3C V/3.3V, High Bandwidth, Hot Insertion 8-Bit, 2-Port, Bus Switch. Description. Features. Pin Configuration. Block Diagram.
Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth Operation (>400 MHz) Permits Hot Insertion 5V I/O Tolerant Rail-to-Rail 3.3V or 2.5V Switching 2.5V Supply Voltage
More informationPT7M6314US. Supervisory Circuit General Description. Features. Pin Configuration. Description
Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:
More informationPI6CL V/1.5V, 200MHz, 1:4 Networking Clock Buffer. Features. Description. Pin Description
Features High-speed, low-noise, non-inverting 1:4 buffer Maximum Frequency up to 200 MHz Low output skew < 100ps Low propagation delay < 3.5ns Optimized duty cycle 3.3 tolerent input 1.2 or 1.5 supply
More informationPI3CH200 2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail
More informationPI3CH Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching
More informationPI5C3384 PI5C3384C. 10-Bit, 2-Port Bus Switch
PI5C3384 PI5C3384C 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.2μA typical)
More informationPI5C Bit Bus Switch with Individual Enables A 1 B 1 GND. Features. Description. Pin Configuration. Block Diagram.
2-Bit Bus Switch with Individual Enables Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2μA typical)
More informationPI5V330S. Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux. Features. Description. Block Diagram. Pin Configuration.
Features High-performance solution to switch between video sources Wide bandwidth: 570 MHz (typical) Low On-Resistance: 5Ω (typical) Low crosstalk at 10 MHz: 80dB Ultra-low quiescent power (0.1µA typical)
More informationPI3CH360 3-Channel 2:1 Mux/DeMux, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching - 0 to 5V switching
More informationPT7M7803/ / μp Supervisor Circuits
Features Precision supply-voltage monitor -.6V (PT7M78xxL) -.8V (PT7M78xxM) -.08V (PT7M78xxT) -.9V (PT7M78xxS) -.6V (PT7M78xxR) -.V (PT7M78xxZ) -.0V (PT7M78xxY) -.00V (PT7M78xxJ) -.5V (PT7M78xxK) -.80V
More informationPI5A3167C Low Voltage SPST 0.8Ω Analog Switch
Features Description CMO Technology for us and nalog pplications Low On-Resistance: 0.8Ω at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail ignal Range Control Input Overvoltage Tolerance: 5.5V Fast Transition
More informationPI6CX201A. 25MHz Jitter Attenuator. Features
Features PLL with quartz stabilized XO Optimized for MHz input/output frequency Other frequencies available Low phase jitter less than 30fs typical Free run mode ±100ppm Single ended input and outputs
More informationI/O Name Descriptions
Features Output Current: 300mA or more Dropout Voltage: 270mV @ 300mA for 3.3V Operating Voltage Range: 1.8V to 5.5V Output Voltage Range: 1.2V to 3.3V (100mV Step) Low Power Consumption: 65 A Standby
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2µA typical) Ideally suited for notebook applications
More information4-Pin Microprocessor Power Supply Supervisors with Manual Reset
4-Pin Microprocessor Power Supply Supervisors with Manual Reset, CAT812 FEATURES Precision monitoring of +5.0 V (± 5%, ± 10%, ± 20%), +3.3 V (± 5%, ± 10%), +3.0 V (± 10%) and +2.5 V (± 5%) power supplies
More informationDescription. Applications
μp Supervisor Circuits Features Precision supply-voltage monitor - 4.63V (PT7A7511, 7521, 7531) - 4.38V (PT7A7512, 7522, 7532) - 3.08V (PT7A7513, 7523, 7533) - 2.93V (PT7A7514, 7524, 7534) - 2.63V (PT7A7515,
More informationPI5V330A. Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux. Features: Description. Pin Diagram. Block Diagram. Pin Description.
Features: High-performance solution to switch between video sources Wide bandwidth: >360 MHz Low On-Resistance: 3Ω Low crosstalk at 0 MHz: 58dB Ultra-low quiescent power (0.µA typical) Single supply operation:
More informationPT8A977B/978B/978BL 5-Function Remote Controller. Features. Description. Ordering Information
Features PT8A977B works as encoder and PT8A978B/ 978BL works as decoder Five pins for five control functions Operating power-supply voltage: 2.5V to 5.0V (978B), 2.0V to 5.0V (978BL), 1.8V to 5.0V(977B)
More informationMM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
More information2.5V/3.3V 500MHz Low Skew 1-to-10 Differential to LVPECL Fanout Buffer with 2 to 1 Differential Clock Input Mux
2.5V/3.3V 500MHz Low Skew 1-to-10 Differential to LVPECL Fanout Buffer with 2 to 1 Differential Clock Input Mux Features F MAX = 500MHz 10 pairs of differential LVPECL outputs Low additive jitter,
More informationFST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
More informationPI5C32X384/32X384C. 20-Bit, 2-Port Bus Switch. Features. Description. Pin Configuration. Block Diagram. Pin Description
PI5C32X384/32X384C Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power 32X384 (0.2µA typical) Ideally suited
More informationPI5C3384 PI5C3384C PI5C32384 (25Ω)
PI5C3384 PI5C3384C PI5C32384 (25Ω) 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay Low noise, 25Ω version (PI5C32384) 5Ω switches connect inputs to outputs (PI5C3384) Direct bus connection
More informationPI3C V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch
2.5V/3., High Bandwidth, Hot Insertion Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth (>400 MHz) Permits Hot Insertion. Rail-to-Rail, 3. or 2.5V ing 5V I/O
More informationPI3USB10LP-A. USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications. Description. Features.
Features USB 2.0 compliant (high speed and full speed) R ON is 5.5Ω typical @ V CC = 3.0V Low bit-to-bit skew Low Crosstalk: 40dB @ 500 Mbps Off Isolation: 35dB @ 500 Mbps Near-Zero propagation delay:
More informationOscillator fail detect - 12-hour Time display 24-hour 2 Time Century bit - Time count chain enable/disable -
Features Description Using external 32.768kHz quartz crystal Real-time clock (RTC) counts seconds, minutes hours, date of the month, month, day of the week, and year with leap-year compensation valid up
More informationFeatures. General Description. Ordering Information. Data Sheet PT8A977P/977W/978P/978LW 5-Function Remote Controller
Features PTAP/W works as encoder and PTAP/LW works as decoder Five pins for five control functions Operating power-supply voltage:.v to.0v (P, W, P),.0V to.0v (LW) Auto-power-off if no press on any button
More informationPT7M8205 LDO Regulator
PT7M8205 Features Output Current: 300mA or more Dropout Voltage: 270mV @ 300mA for 3.3V Operating Voltage Range: 1.8 to 5.5V Output Voltage Range: 1.2 to 3.3V (100mV Step) Low Power Consumption: 65A High
More informationPI74LPT244. Fast CMOS 3.3V 8-Bit Buffer/Line Driver. Features. Description. Block Diagram. Pin Configuration
Fast CMOS 3.3V 8-Bit Buffer/Line Driver Features Compatible with LCX and LVT families of products Supports 5V Tolerant Mixed Signal Mode Operation Input can be 3V or 5V Output can be 3V or connected to
More informationPI74STX2G Bit Level Shifting Buffer/Transceiver with Configurable Dual Supply Voltage. Features. Description. Block Diagram
2-Bit Level Shifting Buffer/Transceiver with Features Operation Voltage: 1.65V V DDA 3.6V 2.3V V DDB 5.5V V DDA V DDB High Speed: tpd = 5ns typical into 30pF @ 3V V DD Power down high-impedance inputs
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON ESD Protection up to 2kV HBM Ultra Low Quiescent Power (0.2μA typical) Ideally suited
More informationMM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability
More informationPI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:
More informationPT7M mA, High PSRR, LDO Regulator Description. Features. Applications. Pin Assignment. Pin Description Pin No I/O Pin Name Description 1 I VIN
Features Input Voltage Range:.7V to 5.5V 3mA Guaranteed Output Current Stable with.47f Ceramic Output Capacitors Low Dropout Voltage 5mV@5mA (Vout=2.8V) Low Quiescent Current 36A High PSRR 75dB@kHz Auto
More informationMM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well
More informationDescription IA 3 IA 2 IA 1 GND. Truth Table (1) H X X Hi-Z Disable S 0-1. L L L I0 S1-0 = 0 L L H I1 S1-0 = 1 Y A to Y B
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (300MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 2.5V and 3.3V supply voltage
More informationMM74HC00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
More informationCD4541BC Programmable Timer
CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,
More informationFeatures. Description. Pin Configuration PT7M CL/CH/NL. Low Power Voltage Detector
Low Power Voltage Detector Features Highly accurate: 1.5% (25 C) Low power consumption: 1μA @ 3.6V Vcc Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1.2V ~ 5.5V Operating
More informationPI6C49X0204A. Low Skew 1 TO 4 Clock Buffer. Features. Description. Block Diagram. Pin Assignment
Features ÎÎLow skew outputs (250 ps) ÎÎPackaged in 8-pin SOIC ÎÎLow power CMOS technology ÎÎOperating Voltages of 1.5 V to 3.3 V ÎÎOutput Enable pin tri-states outputs ÎÎ3.6 V tolerant input clock ÎÎIndustrial
More informationPI90LV031A PI90LV027A PI90LV017A. 3V LVDS High-Speed Differential Line Drivers. Description. Features PI90LV027A PI90LV031A PI90LV017A
PI90LV03A PI90LV027A PI90LV07A 3V LVDS High-Speed Differential Line Drivers Features Signaling Rates >400Mbps (200 MHz) Single 3.3V Power Supply Design ±30mV Differential Swing Maximum Differential Skew
More informationPI3V314. Low On-Resistance, 3.3V High-Bandwidth 3-Port, 4:1 Mux/DeMux VideoSwitch. Features. Description. Pin Configuration.
3-Port, 4:1 Mux/DeMux VideoSwitch Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (375MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V
More informationMicroprocessor Supervisory Circuit ADM1232
Microprocessor Supervisory Circuit FEATURES Pin-compatible with MAX1232 and Dallas DS1232 Adjustable precision voltage monitor with 4.5 V and 4.75 V options Adjustable strobe monitor with 150 ms, 600 ms,
More informationINTEGRATED CIRCUITS. 74LVC00A Quad 2-input NAND gate. Product specification Supersedes data of 1997 Aug 11 IC24 Data Handbook.
INTEGRATED CIRCUITS Supersedes data of 1997 Aug 11 IC24 Data Handbook 1998 Apr 28 FEATURES Wide supply range of 1.2V to 3.6V Complies with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5V CMOS
More informationIDT9170B CLOCK SYNCHRONIZER AND MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET IDT9170B Description The IDT9170B generates an output clock which is synchronized to a given continuous input clock with zero delay (±1ns at 5 V VDD). Using IDT s proprietary phase-locked loop
More informationINTEGRATED CIRCUITS. PCA9515 I 2 C bus repeater. Product data Supersedes data of 2002 Mar May 13
INTEGRATED CIRCUITS Supersedes data of 2002 Mar 01 2002 May 13 PIN CONFIGURATION NC SCL0 1 2 8 V CC 7 SCL1 SDA0 3 6 SDA1 GND 4 5 EN DESCRIPTION The is a BiCMOS integrated circuit intended for application
More informationPI3CH360. Low Voltage, High-Bandwidth, 3-Channel 2:1 Mux/DeMux, NanoSwitch. Features. Description. Block Diagram. Pin Configuration.
Low Voltage, High-Bandwidth, 3-Channel 2:1 Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching 5V I/O tolerant
More informationPI5PD2068/ mΩ Current-Limited, Power-Distribution Switches
Features 7mΩ High-Side MOSFET 2.1A Continuous Current Thermal and Short-Circuit Protection Accurate Current Limit (2.85A typ.) Operating Range: 2.7V to 5.5V.6ms Typical Rise Time Under-Voltage Lockout
More informationFST Bit Low Power Bus Switch
FST3384 10-Bit Low Power Bus Switch General Description The Fairchild Switch FST3384 provides 10 bits of highspeed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to
More informationFST3253 Dual 4:1 Multiplexer/Demultiplexer Bus Switch
Dual 4:1 Multiplexer/Demultiplexer Bus Switch General Description The Fairchild Switch FST3253 is a dual 4:1 high-speed CMOS TTL-compatible multiplexer/demultiplexer bus switch. The low on resistance of
More informationCD4047BC Low Power Monostable/Astable Multivibrator
Low Power Monostable/Astable Multivibrator General Description The CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and
More informationFST Bit Bus Switch
FST3126 4-Bit Bus Switch General Description The Fairchild Switch FST3126 provides four high-speed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to be connected to
More informationICS512 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS512 Description The ICS512 is the most cost effective way to generate a high-quality, high frequency clock output and a reference clock from a lower frequency crystal or clock input. The name
More informationUNISONIC TECHNOLOGIES CO., LTD 1812A/1812B/1813
UNISONIC TECHNOLOGIES CO., LTD 2A/2B/ SINGLE SOUND GENERATOR DESCRIPTION The UTC 2A/2B/ is a CMOS LSI chip designed for use in sound effect products.it is equipped with tone circuit, noise circuit and
More informationPT7C43190 Real-time Clock Module
PT7C43190 Real-time Clock Module Features Description Low current consumption: 0.3µA typ. (V DD =3.0V, T A = 25 C) Wide operating voltage range: 1.35 to 5.5 V Minimum time keeping operation voltage: 1.25
More informationICS LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS670-02 Description The ICS670-02 is a high speed, low phase noise, Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques. Part of IDT
More informationFST Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch
September 1997 Revised November 2000 FST16233 16-Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch General Description The Fairchild Switch FST16233 is a 16-bit to 32-bit highspeed CMOS TTL-compatible
More informationCD4538 Dual Precision Monostable
CD4538 Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationSERIALLY PROGRAMMABLE CLOCK SOURCE. Features
DATASHEET ICS307-02 Description The ICS307-02 is a versatile serially programmable clock source which takes up very little board space. It can generate any frequency from 6 to 200 MHz and have a second
More information3V 10-Tap Silicon Delay Line DS1110L
XX-XXXX; Rev 1; 11/3 3V 1-Tap Silicon Delay Line General Description The 1-tap delay line is a 3V version of the DS111. It has 1 equally spaced taps providing delays from 1ns to ns. The series delay lines
More informationMM74C925 MM74C926 MM74C927 MM74C928 4-Digit Counters with Multiplexed 7-Segment Output Drivers
October 1987 Revised January 1999 MM74C925 MM74C926 MM74C927 MM74C928 4-Digit Counters with Multiplexed 7-Segment Output Drivers General Description The MM74C925, MM74C926, MM74C927 and MM74C928 CMOS counters
More informationPI6C V/3.3V 1.5GHz Low Skew 1-to-10 Differential to LVPECL Fanout Buffer with 2 to 1 Differential Clock Input Mux /Q4 /Q5 /Q6 /Q3
LVPECL Fanout Buffer with 2 to 1 Differential Clock Input Mux Features ÎÎF MAX < 1.5GHz ÎÎ10 pairs of differential LVPECL outputs ÎÎLow additive jitter, < 0.03ps (typ) ÎÎSelectable differential input pairs
More informationPI3L V Quad, 2:1 Mux/DeMux Fast Ethernet LAN Switch w/ Single Enable. Description. Features. Applications. Pin Configuration.
Features R ON is 4Ω typical Low crosstalk: 27dB @ 250 MHz Near-Zero propagation delay: 250ps Switching speed: 9ns Channel On capacitance: 9pF (typical) Operating Range: +3.0V to +3.6V >2kV ESD protection
More informationICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-51 Description The ICS180-51 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase-Locked Loop (PLL) technology
More informationFST32X Bit Bus Switch
FST32X245 16-Bit Bus Switch General Description The Fairchild Switch FST32X245 provides 16-bits of high speed CMOS TTL-compatible bus switching in a standard flow-through mode. The low On Resistance of
More informationDescription Q0+ Q0- Q1+ Q1- Q2+ Q2- VDD Q3+ Q3- Q4+ Q4- CLK_SEL CLK0. nclk0 Q5+ Q5- SYNC_OE Q6+ Q6- CLK1. nclk1 Q7+ Q7- VEE Q8+ Q8- Q9+ Q9-
LVPECL Fanout Buffer with Sync OE Features ÎÎF MAX < 1.5GHz ÎÎ10 pairs of differential LVPECL/ ECL outputs ÎÎLow additive jitter, < 0.03ps (typ) ÎÎSelectable differential input pairs with single ended
More informationSEMICONDUCTOR FAC1509 TECHNICAL DATA. 2A 150KHZ PWM Buck DC/DC Converter. General Description. Features. Applications. Package Types DIP8 SOP8
SEMICONDUCTOR TECHNICAL DATA FAC1509 General Description The FAC1509 is a of easy to use adjustable step-down (buck) switch-mode voltage regulator. The device is available in an adjustable output version.
More informationCD4538BC Dual Precision Monostable
CD4538BC Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationINTEGRATED CIRCUITS. PCA channel I 2 C hub. Product data Supersedes data of 2000 Dec 04 File under Integrated Circuits ICL03.
INTEGRATED CIRCUITS Supersedes data of 2000 Dec 04 File under Integrated Circuits ICL03 2002 Mar 01 PIN CONFIGURATION SCL0 SDA0 1 2 16 V CC 15 EN4 DESCRIPTION The is a BiCMOS integrated circuit intended
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 256K (32K x 8) Static RAM Features Temperature Ranges Commercial: 0 C to
More informationICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-01 Description The ICS180-01 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase Locked Loop (PLL) technology
More informationZ86116 CMOS Z8 PN MODULATOR WIRELESS CONTROLLER CUSTOMER PROCUREMENT SPECIFICATION FEATURES GENERAL DESCRIPTION Z86116 CP95WRL0501 PRELIMINARY
PRELIMINARY CUSTOMER PROCUREMENT SPECIFICATION CMOS Z8 PN MODULATOR WIRELESS CONTROLLER FEATURES ROM RAM* SPEED Part (Kbytes) (Kbytes) (MHz) 1 124 12 * General-Purpose 18-Pin DIP and SOIC Packages 3.0-
More information74AC04 74ACT04 Hex Inverter
74AC04 74ACT04 Hex Inverter General Description The AC/ACT04 contains six inverters. Ordering Code: Features I CC reduced by 50% on 74AC only Outputs source/sink 24 ma ACT04 has TTL-compatible inputs November
More informationCAT bit Programmable LED Dimmer with I 2 C Interface DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT
16-bit Programmable Dimmer with I 2 C Interface FEATURES 16 drivers with dimming control 256 brightness steps 16 open drain outputs drive 25 ma each 2 selectable programmable blink rates: frequency: 0.593Hz
More informationMM74C925 MM74C926 4-Digit Counters with Multiplexed 7-Segment Output Drivers
MM74C925 MM74C926 4-Digit Counters with Multiplexed 7-Segment Output Drivers General Description The MM74C925 and MM74C926 CMOS counters consist of a 4-digit counter, an internal output latch, NPN output
More information500mA CMOS Ultra Low Dropout Linear Regulator
500mA CMOS Ultra Low Dropout Linear Regulator Description The series are 500mA CMOS ultra low dropout positive voltage regulators which operate from 2.4V to 5.5V input supply. The ultra low dropout linear
More informationQuad Single Supply Comparator
TECNICAL DATA Quad Single Supply Comparator IL339 The IL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 m max for four comparators which
More informationICS502 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS502 Description The ICS502 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output and a reference from a lower frequency crystal or clock input. The
More information64K x 1 Static RAM CY7C187. Features. Functional Description. Logic Block Diagram. Pin Configurations. Selection Guide DIP. SOJ Top View.
64K x 1 Static RAM Features High speed 15 ns CMOS for optimum speed/power Low active power 495 mw Low standby power 110 mw TTL compatible inputs and outputs Automatic power-down when deselected Available
More informationICS NETWORKING AND PCI CLOCK SOURCE. Description. Features. Block Diagram DATASHEET
DATASHEET Description The is a low cost frequency generator designed to support networking and PCI applications. Using analog/digital Phase Locked-Loop (PLL) techniques, the device uses a standard fundamental
More information