HYDRA ANTENNA INSTALL INSTRUCTIONS. A step by step guide for self-installation of the Hydra antenna
|
|
- Annabel Cole
- 5 years ago
- Views:
Transcription
1 HYR NTENN INSTLL INSTRUTIONS step by step guide for self-installation of the Hydra antenna
2 ONTENTS NTENN SPEIFITION... WHT YOU NEE TO PROVIE... SITE SURVEY SITE SELETION OR THE SHIP... HYR TYPIL MOUNTING EXMPLE... USE OF PEESTL... ) REMOVE NTENN FROM PKGING...7 ) REMOVE KIT G FROM OX...8 ) REMOVE OME LI...9 ) REMOVE SFETY OLTS...0 ) SEURE OME... ) LIGNING THE NTENN... 7) TTH OME TO PEESTL N ING LOKTITE TO THE OLTS... 8) SET UP ONNETION WIRING... 9) SET UP ETHERNET ONNETION WIRING... 0) USE OF RIMP TOOL... ) ONNET THE ONNETORS...7 ) ONNET TO NTENN ETHERNET...8 ) POWER THE NTENN...9 FREE OFFER...0 Page
3 HYR SPEIFITIONS ish iameter: cm ntenna imension: 79.cm(H) x.cm() ntenna Weight (With ome): Kg Radome Material: Plastic Rx Frequency: GHz Tx Frequency:.7-.GHz Rx Tx Gain: U: LN: W Quad and LN Stabilisation: -axis active stabilisation Skew control: utomatic Elevation ngle: -0 to +00 zimuth ngle: Unlimited ross ngle: +/-0 Tracking speed: 0 per sec Ships Motion: Yaw: +/- 8 at 0sec period Pitch: +/- 7 at 8sec period Roll: +/- 0 at 8sec period Temperature: -0 to + Input Power: 90-V full range, 7-Hz ontrol Interface: Via local internet connection Packing Size: 8 x 8 x 9cm Gross Weight: Kg Packaging: ardboard Page
4 WHT YOU NEE TO PROVIE You will need to provide the following for a safe and successful install:. Your own Wi-Fi access point as this does not come in our kit.. ore Power cable must conform to marine standards. cable similar to MPRXX / MPRXX FLEXISHIP 0./ (.) should be used for the power connection. Specifications followed should be; STNRS International: IE 009-0; IE 009-; IE 009-0; IE 08; IE 0-; IE 0--; IE 07-; IE 07-; IE 0. ate cable must conform to marine standards. cable similar to ergen abling - NV Maritime LN S/FTP T cable should be used for the ethernet connection. Specifications followed should be; STNRS; EN 07-; EN ISO/IE 80; IE -. ase to install the antenna, as described in section Hydra Typical Mounting Example, see page... Power: 00 0V, 0/0Hz,.. The power requires a plug that matches your standard power system.. We recommend an on/off switch below deck. 7. lue Mobile is not responsible for manufacture and/or installation of mounting pedestal. Please see end of guide for a typical mounting example. 8. ntenna includes parts for above decks installation. Please note lue Mobile does not supply below decks equipment (i.e. routers, etc.) and is not responsible for below decks configuration. Page
5 SITE SURVEY Site Selection board the Ship What to take into consideration when selecting an appropriate position: e aware of the surroundings while mounting the antenna. ny interference or blockage between the antenna and the satellite can cause signal strength loss or worse satellite connection failure. Therefore, securing the antenna in a position where minimal blockage, allowing a clear line of sight. Make sure that the cables running are safely secured to the ship and are not hanging freely with any exposed areas. ausing no harm to anyone or the cables themselves. The antenna must be a minimum of meters away from the ship s radar The antenna must allow significant space for x band navigational radars, at around metres. The antenna must also allow significant space for high frequency antennas of around metres. The antenna must be at least metres away from any other GPS antennas. eware of a radiational hazard around the antenna. ll personal must be at least a distance of 0 metres away from this zone. Note: Hydra antenna must be out of the 0 degree zone of a typical radar system. Microwave Radiation Zone. Please keep a safe distance of 0 meters away. Thank you. Page
6 7,0 80,00 HYR TYPIL MOUNTING EXMPLE ITEM PRTS LIST QTY PRT NUMER px08-x px07-p NSI 8...M - M x.7 x ESRIPTION Ethernet onnector IP Rated - Wiring Side Power onnector IP Rated - Wiring Side Hex olt 70,00 0,00,00 H ( + 0, 7 0-0, 00) 0,00 ntenna ssembled 0,00 Iso Lowered ( : ) ow 7,0 0,00 ottom View ( : 0 ) Notes: ll Sizes in mm unless otherwise stated ntenna Weight - Kg Stand shown as "Typical" mounting able wiring for antenna must be marine grade and is specified in the installation guide Pole diameter 0 mm Standard Stand ( : ) Mounted ntenna ( : ) ate esigned by hecked by pproved by ate luemobile 8/0/08 luemobile Ltd. Hydra Typical Mounting Hydra Mounting Spec New / USE OF THE PEESTL - USTOMER RESPONSIILITY The following circumstances should be followed with the use of the pedestal: Make sure that the pedestal being used is robust enough that during ship movement or other factors such as wind do not affect it or the radome. llow for easy and safe access to the radome if its mounted to the pedestal, meaning easier access for engineers. llow easy access to plug in the power and ethernet cable into the radome. Page
7 REMOVE NTENN FROM PKGING Remove the antenna out of the box and packaging. ox: The antenna will be shipped in this ox Lid: Removable part to get access to the antenna ntenna: The antenna Small box: Parts kit will be available in here Page 7
8 REMOVE KIT G FROM OX Kit bags will be stored inside a small box, found inside the large box next to the dome. x ome Power onnector, ULGIN PX07/S x Ethernet onnector, ULGIN PX08 x Tablet x RJ onnector rimp Tool x M Pedestal olts x M ome olts 7 x M Washers 8 x M Washers 9 x M Rubber Washers 0 x M Nylock Nuts x Spare RJ Ethernet onnectors Wooden box containing kit x ottle of Locktite M Eye olt Page 8
9 REMOVE OME LI Remove the dome lid off the antenna. Page 9
10 Remove the following safety pins. llowing the antenna to move freely. Remove the following safety pins. llowing the antenna to move freely. Step Remove : the Locate following safety safety bolts. pins. llowing the antenna to move freely. Step : With Locate a nut safety securing bolts. bolt. With a nut Step securing : Locate safety bolts. With REMOVE bolt a nut securing SFETY. OLTS bolt. Notes: Feature,, : Remove these bolts. There are safety bolts that need removing to allow the antenna to freely. They can be PRTS LIST Feature,, Notes: : Remove these bolts. ate seen in the drawing PRTS above. LIST esigned by hecked by pproved by ate ate Remove ITEM QTY the following PRT NUMER safety pins. llowing ESRIPTION the antenna to move freely. /0/08 Step : NSI Locate 8...M safety - M8 x bolts.. x 80With PRTS a nut LIST securing Hex olt bolt. lue Mobile ate PRT NUMER ESRIPTION M8 Hex Nut Hydra ManualGuide Install Remove Step ITEM QTY Hex olt : the Remove PRT following the NUMER lue Mobile safety bolts pins. and llowing nut located ESRIPTION Hex Nut ManualGuide NSI 8...M - M8 x. x 80 Hex olt the antenna to move freely. lue Mobile Step here. M8 Hex Nut ManualGuide : Remove the bolts and nut located here. ITEM QTY NSI 8...M - M8 x. x 80 M8 Notes: Notes: Feature,, : Remove these bolts. Feature,, : Remove these bolts. esigned by hecked by pproved by ate /0/08 Hydra Install Manual esigned by hecked by pproved by ate /0/08 Hydra / Install Manual / / ITEM QTY PRT NUMER NSI 8...M - M8 x. x 80 M8 PRTS LIST Hex olt Hex Nut ESRIPTION esigned by hecked by pproved by ate ate /0/08 Hydra Install Manual lue Mobile ManualGuide / Page 0
11 Securing the dome lid to the dome base. SEURE THE OME. E Securing the dome lid to the dome base. Securing the dome lid to the dome base. E E ITEM OME E E E E PRTS LIST QTY PRT NUMER PRTS LIST ESRIPTION NSI 8...M ITEM QTY - M x x 0 PRT NUMER PRTS Hex LIST olt ESRIPTION NSI 8.M ITEM QTY - NSI N 8...M PRT - M NUMER x x 0 Metric Plain Hex olt Washers ESRIPTION NSI 8.M 8...M - - NM x x 0 Metric Hex olt Plain Washers M Rubber Washers esigned by hecked by pproved by ate ate M Metric Rubber Plain Washers Hex olt esigned by hecked by pproved by ate ate NSI 8..M - Property lass and Prevailing 0 - Prevailing Torque M Rubber Torque Type Washers Type Hex Hex Nut Nut - - Steel /0/08 Steel /0/08 esigned by hecked by pproved by ate ate Metric M x Metal Metric NSI Type 8..M M x Metal - Property Type lass and Metric Metric Prevailing Property - Property Torque lass lass Type,9 Hex and and Nut 0Metric Plain Washers - Steel Hydra Install /0/08 Hydra Manual Install Manual Metric M x Metal Type Metric - Property lass,9 and M 0 Rubber Washers lue lue Mobile Mobile Hydra Install Manual MRINE EYE OLTS MM X 0MM PK M Eye olts ManualGuide lue Mobile / MRINE EYE OLTS MM X 0MM PK M Eye olts ManualGuide / MRINE EYE OLTS MM X 0MM PK M Eye olts Prevailing Torque Type Hex Nut ManualGuide - Steel Metric - Property / lass,9 and 0 Securing NSI 8.M - N NSI 8..M the dome - Property lid lass to and the 0 - dome base. M Eye olts E Page
12 lignning the connectors with the front of the ship. LIGNING THE NTENN VESSEL OW VESSEL OW IMGE IMGE ligning the connectors with the front of the ship. Notes: In image you can see that the two front pedestal holes are at right angle with the front/bow of the ship. Notes: In image you can see that the two front pedestal holes are at right angle with the front/bow of the ship. ate esigned by hecked by pproved by ate luemobile /0/08 offsets / efore mounting the antenna and pedestal, it is very valuable to align with vessel bow as much as possible. Page
13 7 Securing the TTH dome OME to the TO pedestal PEESTL and N ING LOKTITE TO THE OLTS adding locktite to the bolts. F F F F M x Hex olt M Metric Plain Washers ottle of Locktite Securing the dome to the pedestal and adding locktite to the bolts. Note: Making sure you place some locktite onto the end of each of the bolts before you place them through the pedestal and dome. Note: Making sure you place some PRTS locktite LIST onto the end of each of the bolts before you place them through the pedestal and dome. ITEM QTY PRT NUMER ESRIPTION esigned by hecked by pproved by ate ate NSI 8...M - M x.7 x M x Hex olt /0/08 Hydra Install Manual NSI 8.M - N M Metric Plain Washers lue Mobile Locktite ManualGuide / 9 Page
14 8 SET UP POWER ONNETION WIRING ONNETIONS ERTH NEUTRL LIVE Power onnector ore Power cable must conform to marine standards. cable similar to MPRXX / MPRXX FLEXISHIP 0./ (.) should be used. Please note that the below deck side of this wiring requires a plug that matches your ships standard power. Page
15 9 Ethernet onnection SET UP ETHERNET ONNETION WIRING ITEM QTY PRT NUMER RP-00MM-TLM700 RJ Ethernet onnector ate cable must conform to marine standards. cable similar to -0-0 Note: Please remember to put on the black cable mount before crimping the RJ connector. abling IMGE PRTS LIST ESRIPTION Ethernet onnector onnector ate cable must conform to marine standards. cable similar to -0-0 esigned by hecked by pproved by ate ate lue Mobile 7 WIRING PROPERTIES - PRT Wiring Side Wiring Side Wiring olour Wire Gauge Pin Wiring Properties Pin - Part Orange White Wiring Side Wiring Pin Side Pin Wiring olour Orange Wire Gauge Pin Pin Pin Pin Orange Green White White Pin Pin Pin Pin Orange lue Pin Pin Pin Pin Green White lue White Pin Pin Pin Pin lue Green Pin Pin Pin 7 Pin 7 lue White rown White Pin Pin Pin 8 Pin 8 Green rown Pin 7 Pin 7 rown White Pin 8 Pin 8 rown IMGE ManualGuide 8 /0/08 Hydra Install Manual / IMGE shows the how the ate cable will line up with the RJ connector. Make sure that you have placed the connector on before moving on to the crimping step. IMGE shows the final product for the ethernet connector to the antenna, seen in the diagram on page 8 and tagged as number. Placing the wire through the connector before crimping. Page
16 0 USE OF RIMP TOOL egin by stripping back one side of the ate cable using the cable stripper part of the crimp tool (). Your cable should look something like (). Unwind the individual wires and straighten them out, ready to be inserted into the RJ connector. e sure to follow the color guide on previous page. You must make sure that all the wires are of the same length and that they are mm long (.7 mm to be precise). You can reduce the size of the wires using scissors or the cable cutter part of the crimp tool. arefully placing them into the connector, making sure they keep the same order and reach the end of the connector. Note that the connector must be the right way up, which can be seen on previous page. You are now ready to crimp the connector and wiring into place. Insert the connector while holding the cable to the crimp part of the crimp tool. It should fit nicely. Please repeat the same steps for the reversed side of the cable. Page
17 onnect the power and ethernet connectors to the ntenna. ONNET THE ONNETORS onnect the power and ethernet connectors to the antenna. otes: ake sure the cables hanging from the antenna are safely cured to either the pedestal so there are no hazards. Notes: Make sure the cables hanging from the antenna are safely secured to either the pedestal so there are no hazards. esigned by hecked by pproved by ate ate lue Mobile ManualGuide /0/08 Hydra Install Manual 8 / 9 Page 7
18 Option : irectly onnect to P ONNET TO NTENN ETHERNET Option : irectly onnect to P Option : onnect to ships IT Ethernet onnection Notes: onnect your antenna straight to your laptop via ethernet connection. Notes: onnect your antenna straight to your laptop via ethernet connection. Option : onnect to ships IT esigned by hecked by pproved by ate ate luemobile /0/08 connecttolaptop / Option of ethernet connection or wifi Notes: onnect the antenna to your ships router or IT method through ethernet. From there you can either connect your laptop via wifi or ethernet connection. Ethernet onnection Notes: onnect the antenna to your ships router or IT method through ethernet. From there you can either connect your laptop via wifi or ethernet connection. ntenna Ethernet connector provides internet connection & also access to antenna interface via web browser. ntenna provides IP address via HP. esigned by hecked by pproved by ate ate luemobile /0/08 connecttolaptop / Page 8
19 POWER THE NTENN Now you may power up your antenna. orrect installation will result in the antenna searching and locking onto a satellite. Please visit to view the antenna interface. ) ntenna Interface ntenna will search for correct satellite and lock automatically. Status can be seen on interface. If you are not getting an internet connection, please check that you are not in the shadow of the mast. On first use the system may take some time to download updates from the network. llow for 0 minutes for the system to stabilise before usage. ) Page 9
20 FREE 00 M T PKGE Enjoy your internet from lue Mobile. Please could you use your tablet to take pictures of your installation including a view towards the radar and bridge, and to support@ blue-c-mobile.com also including the IMO of the ship. In return we ll credit you with 00 M of data package for free! ONGRTULTIONS ON MKING YOUR SHIP LUE MOILE REY! FOR YOUR FREE 00M T PKGE EMIL US PHOTOS OF YOUR Page 0
Thuraya Orion IP Satellite Terminal. Maritime Installation Guide
Thuraya Orion IP Satellite Terminal Maritime Installation Guide 3500867-0001 Revision 2 November 27, 2013 Copyright 2013 Hughes Network Systems, LLC All rights reserved. This publication and its contents
More informationINTRODUCTION TOOLS AND SUPPLIES
INTROUTION 1 The MFJ Ground-oupled gives you a stable way to mount your vertical antenna and provides an effective ground by just setting the base down and standing on it to push the legs firmly into the
More informationCopyright 2013 Hughes Network Systems, LLC
Copyright 2013 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary to Hughes Network Systems, LLC. No part of this publication may be reproduced in any form
More informationCSA-450 Multi Fully automatic, auto-tracking marine Satellite antenna with 3 outputs
CSA-450 Multi Fully automatic, auto-tracking marine Satellite antenna with 3 outputs Instruction Manual Ver. 1.2 Thank you for purchasing our product. Please read this instruction manual carefully before
More informationHughes 9450 Mobile Satellite Terminal. Installation Guide
Hughes 9450 Mobile Satellite Terminal Installation Guide 3004129 Revision A September 15, 2010 Copyright 2010 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary
More informationNevco Indoor Accessory Driver IAD Installation Manual
Nevco Indoor ccessory river I Installation Manual Retain this manual in your permanent file. 0//7 5-00R Installation Instructions Installation consists of three steps: Unpacking the equipment, Indoor ccessory
More informationDME Final Project Brief Project Summary
Matthew radley Omar Ghani ME Final Project 0070 rief Project Summary Objective To design a retracting mechanism for a communication board that is to be attached to a mobile wheelchair, with the following
More informationGMR 420/620/1220 xhd2 Series Installation Instructions
GMR 420/620/1220 xhd2 Series Installation Instructions To obtain the best performance and to avoid damage to your boat, install the device according to these instructions. Read all installation instructions
More informationGMR FANTOM 50/120 SERIES INSTALLATION INSTRUCTIONS
GMR FANTOM 50/120 SERIES INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important
More informationOhio - TV Unit MADE IN BRITAIN. Assembly Instructions - Please keep for future reference 309/6561
Ohio - TV Unit ssembly Instructions - Please keep for future reference 09/6561 Dimensions Width - 120cm Depth - 9.5cm Height - 61.5cm MDE IN RITIN Important - Please read these instructions fully before
More informationAAE Model No. PVS-HSX High School Premier Pole Vault Standards
E Model No. PVS-HSX High School Premier Pole Vault Standards luminum thletic Equipment 1000 Enterprise rive, Royersford, P 19468 Toll Free: (800) 53-5471 Fax: (610) 85-378 www.esports.com 8 7 6 5 4 3 1
More information10/17/2011. I have an Air-Card. I have Satellite Internet. Why would I use Wi-Fi? Just for
How much do you use the Internet? Just for e-mail Or. 2011 National HDT Rally How much do you use the Internet? How much do you use the Internet? E-mail Face Book Google Plus Blog reading Blog Writing
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationLinear Motion and Assembly Technologies Aluminum Framing /07. Die-Cast Foundation Brackets 3-10 & 3-11
-0 Linear Motion and ssembly Technologies luminum Framing 91 500 1 /07 Section : Profile onnectors Overview One of the greatest strengths of the osch Rexroth structural aluminum framing system is the wide
More informationArducopter 3DR-B Hardware
Arducopter 3DR-B Thank you for purchasing an Arducopter 3DR kit. The Arducopter 3DR is a stable and supported quadrotor frame in the ongoing development of the Arducopter code on DIYDrones. It features
More informationLS7 CHEVROLET TOP MOUNT Installation Manual For Systems with A/C #13460 / #13490
LS7 CHEVROLET TOP MOUNT Installation Manual For Systems with /C #13460 / #13490 PLESE RED LL INSTRUCTIONS EFORE INSTLLING NY COMPONENTS OF THE TRU TRC SERPENTINE SYSTEM Important: Thoroughly read the instructions,
More informationThe Nantucket Legacy Arbor
SSEMLY INSTRUTIONS The Nantucket Legacy rbor Please read through before starting assembly. IMPORTNT: HEK THE INSIDE OF YOUR POSTS FOR LL MTERILS. heck ox for These ontents In. the Keystone event of missing
More informationHotspot OEM INSTALLATION MANUAL
Hotspot OEM INSTLLTION MNUL TLE OF ONTENTS Introduction 2 Safety Information 2 Resources Required 2 Installation 3 Power Supply 5 Troubleshooting 6 Notes 7 Introduction Hotspot was designed and engineered
More informationMIMO AP-DOUBLE CELL/LTE. The Perfect All-In-One Solution for your In-Vehicle Mobile Access Router ANTENNA AP-CC 3G/4G NEW.
P-DOULE ELL/LTE NTENN P- The Perfect ll-in-one Solution for your In-Vehicle Mobile ccess Router MIMO Multiple In Multiple Out igger Wireless Footprint: y using the P-Double ell/lte ntenna, you can be farther
More informationTools & materials required for each application. Hammer drill Shovel. Masonry bits: Concrete mixing. 7/32", 5/16" equipment
Installation Guide U.S. Version Tools & materials required for each application Hard Surfaces ll pplications Soft Surfaces Mitre saw with a non-ferrous metal cutting blade Post hole digger Hammer drill
More information4-TIER SHELF RACK ITEM # , , MODEL #143654W-DS,143654B-DS,143654C-DS. Français p.9 Español p.17 ATTACH YOUR RECEIPT HERE
ITEM #01903,0062870,00601 TM -TIER SHELF RK MOEL #1365W-S,1365-S,1365-S Français p.9 Español p.17 TTH YOUR REEIPT HERE Serial Number Purchase ate Questions, problems, missing parts? efore returning to
More informationTabletop or Rolling Media Pod
U5 U5-S U6 U6-S Tabletop or Rolling Media Pod ssembly Guide For assistance, please contact us: U5-S_U6-S_2015_ heck out our other products online at www.copernicused.com WRNING 1-800-267-8494 mail info@copernicused.com
More informationGMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS
GMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other
More informationHughes 9450 Mobile Satellite Terminal Series. Installation Guide
Hughes 9450 Mobile Satellite Terminal Series Installation Guide Document No. 3004129-0001 Revision E 17 November 2017 Copyright 2013, 2017 Hughes Network Systems, LLC All rights reserved. This publication
More informationInstallation. Loader Arm Wear Strip Kit TX 1000 Compact Tool Carrier WARNING. Loose Parts. Installation Instructions
Loader Arm Wear Strip Kit TX 1000 Compact Tool Carrier Model No. 133-0241 Form No. 3406-164 Rev B Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or
More informationLINK GPS MGMT DATA. 4 GHz Licensed Backhaul Radio DATA MGMT GPS. Model: AF-4X LINK
LINK GPS MGMT DATA DATA MGMT GPS LINK 4 GHz Licensed Backhaul Radio Model: AF-4X 4 GHz Licensed Backhaul Radio Model: AF-4X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you for purchasing the
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K
K9 KIT INSTALLATION INSTRUCTIONS 1998-2011 CROWN VIC KK-K9-F7-K TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric Socket Set Screwdriver Set Torx Bit
More informationThuraya ATLAS IP+ Installation Manual
Thuraya ATLAS IP+ Installation Manual Installation Manual Revision 1.0 LIST OF CONTENT: REGULATORY INFORMATION 3 SAFETY INSTRUCTIONS 4 IMPORTANT INFORMATION TO INSTALLERS AND USERS 7 ATLAS IP+ TERMINAL
More informationSatellite Terminal. Installation Guide. Release 2.2 Ref. nr
Satellite Terminal Installation Guide Release 2.2 Ref. nr. 37628 Table of Contents Table of Contents Table of Contents... 2 1 Introduction... 3 1.1 About this Guide... 3 1.2 Material Provided in the Box...
More informationLand Station Quick Start Guide
Land Station Quick Start Guide Version 1.0 Read Installation Guide, User Manual and all safety information before installing or using Iridium Pilot Land Station. Failure to do so can result in serious
More informationHughes 9300 Series Mobile Satellite Terminal
Hughes 9300 Series Mobile Satellite Terminal Installation Guide 1038494-0001 Revision E Copyright 2011 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary
More informationCable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench
Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -
More informationMOUNTING HOLES: 4X DIA 0.20 INCH 7.6 X 6.4 INCH PATTERN
4 2 ESRIPTION TE INITIL EVELOPMENT 204/0/08 UPTE K PNEL N PINOUTS 205/0/25 256 NOTES:. ORERING INFORMTION: 02. SKU MVN-700-0-K escription MobileView 7000 NVR Kit Items PORT NVR, HRNESS, ONNETION KIT MobileView
More information20,00 20,00 3,00 TYP. R5,00 1,00 TYP. R3,00 TYP. 2X 4,00 THRU 1,00 TYP. 10,00 10,00 (5,00) 10,00 10,00 19,00 7,00 4,50 THRU R15,00 12,00
,00,00,00 0,0 70,00 0,00 R,00,00 TYP.,00 TYP. R,00 TYP.,00 TYP. X,00 THRU 0,00 0,00 0,00 0,00 0,00 0,00 0,00 (,00) 0,00 0,00 SETION - 9,00 0 0 7,00,0 THRU 0,0 R,00 R,00 R0,0 TYP. ETIL,00 ompetitor: Stainless
More informationHP ProCurve 6.9/7.7dBi Dual Band Directional Antenna (J8999A) Guide
HP ProCurve 6.9/7.7dBi Dual Band Directional Antenna (J8999A) Guide SAFETY The HP ProCurve J8999A and all associated equipment should be installed in accordance with applicable local and national electrical
More informationQUANTITY DISCOUNTS ARE AVAILABLE FOR CONNECTORS AND ADAPTORS
ONNETORS and DPTORS SUMMRY QUNTITY DISOUNTS RE VILLE FOR ONNETORS ND DPTORS ONNETORS ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ ÂÂ EI Flange 7/16" DIN N FME SM and SM TN UHF Mini-UHF MMX Micro Miniature Reverse
More informationHughes 9450 Mobile Satellite Terminal
Hughes 9450 Mobile Satellite Terminal Installation Guide 3004129-0001 Revision C Copyright 2011 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary to Hughes
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationWhite Tongue & Groove 2 Drawer Unit
White Tongue & Groove 2 rawer Unit Assembly Instructions - Please keep for future reference imensions Width - 34cm epth - 28cm Height - 56cm Important - Please read these instructions fully before starting
More informationSteady Freddy Vinyl Gate REALLY. Important stuff to know about installing your WamBam gate
Steady Freddy Vinyl Gate RELLY Important stuff to know about installing your Wamam gate. 1-877-778-5733 www.wambamfence.com CLEVER JOE Your Installation uddy This Gate is lso Designed to Fit the ig en
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS
K9 KIT INSTALLATION INSTRUCTIONS 2005-2011 CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric
More informationScanstrut Installation Instructions SC30
Scanstrut Installation Instructions SC30 Tools Required ø30-50mm (1 1/4-2 ) Drill bits to suit Radome fasteners & drainage hole if needed. Power drill Weather Seal (for use with KVH FB150/250 compact and
More informationSSRLS-3 / SSRLU-3 Installation Instructions
5mm Hex Nut Upper Telescoping hannel & Screws Packing List QTY. ITM 1 Top Telescoping hannel 1 ottom Telescoping hannel w/ self drilling screw 15" 18" 1 Top and ottom Rod with connecting arm 25-½ 2 ¼ -
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationYard & Pool Vinyl Gate REALLY. Important stuff to know about installing your WamBam gate Ver 1, February 2014
Yard & Pool Vinyl Gate RELLY Important stuff to know about installing your Wamam gate. Ver 1, February 2014 1-877-778-5733 www.wambamfence.com Reality Check 1 - Read Over Fence Instructions First Your
More informationWalton - Corner Desk MADE IN BRITAIN. Assembly Instructions - Please keep for future reference 162/8405
Walton - orner esk ssembly Instructions - Please keep for future reference 62/805 imensions Width - 20cm epth - 89.5cm Height - 7cm ME IN RITIN Important - Please read these instructions fully before starting
More informationComponents for low voltage panel boards
omponents for low voltage panel boards UTUMN UTOMTION N ONTRO EETRI ISTRIUTION OEM Products catalogue Ω OK - Unipolar terminal locks PROUTS Ω OK IT 80-11 IT 80-15 G IT 80-7 W IT-S IN35 TEHNI FETURES 31
More informationItem Name: Carlisle Mini Hall Tree SKU: DIME For assistance with assembly, please contact Hayneedle Customer Care Center /12
Item Name: arlisle Mini Hall Tree SU: IM039- For assistance with assembly, please contact Hayneedle ustomer are enter -888-880-4884 /2 PR-ASSMY PRPARATION:! WARNING: Failure to follow these directions
More informationPart No. Thread Size B Design Load Approx. Wt./100 A in. (mm) Lbs. (kn) Lbs. (kg)
ttachments Fig. 3199R - eiling Flange Fig. 3199RT - eiling Flange ura-opper oated Size Range: 3 /8"-16 & 1 /2"-13 rod Material: Malleable Iron (Stainless Steel Type 304 available) Standard 3199RT is UR-OPPER
More informationThuraya ATLAS IP Satellite Terminal
Thuraya ATLAS IP Satellite Terminal Installation Manual Revision 2.0 LIST OF CONTENT: REGULATORY INFORMATION 3 SAFETY INSTRUCTIONS 6 IMPORTANT INFORMATION TO INSTALLERS AND USERS 9 SYSTEM CONFIGURATION
More informationOhio Sideboard MADE IN BRITAIN. Assembly Instructions - Please keep for future reference 314/7128
Ohio - 6+2 Sideboard ssembly Instructions - Please keep for future reference 14/7128 Dimensions Width - 120cm Depth - 9.5cm Height - 78cm MDE IN RITIN Important - Please read these instructions fully before
More informationHughes 9450 Mobile Satellite Terminal
Hughes 9450 Mobile Satellite Terminal Installation Guide 3004129-0001 Revision C Copyright 2012 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary to Hughes
More informationPowersafe Termination Guide
Powersafe Termination Guide Contents Index 1. Introduction 2. Overview 3. Termination Methods 3.1 Set screw termination 3.2. Recommended Assembly Procedure for Panel Mounted Connectors 3.3. Crimp Termination
More informationB3199R - Ceiling Flange B3199RCT - Ceiling Flange Dura-Copper Coated. TOLCO Fig All Steel Ceiling Plate. 216 Eaton
ttachments 3199R - eiling Flange 3199RT - eiling Flange ura-opper oated Size Range: 3 /8"-16 & 1 /2"-13 rod Material: Malleable Iron (Stainless Steel Type 304 available) Standard 3199RT is UR-OPPER coated
More information1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More information08+ KAWASAKI KLR PD NERF
08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of
More informationVarioSole SE. Installation instructions
VarioSole SE Installation instructions INTRODUTION Product Information VarioSole is a universal, easy to install system for the mounting of framed PV modules on pitched roofs with a roof pitch between
More information3 GHz Carrier Backhaul Radio. Model: AF-3X. Tel: +44 (0) Fax: +44 (0) LINK GPS MGMT DATA DATA
LINK GPS MGMT DATA DATA MGMT GPS LINK 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you
More informationSole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing
More informationRotary Measurement Technology Incremental Encoders
-20 to 60 C Temperature Shock/vibration resistant Short-circuit protection Reverse polarity protection High rotational speed Rugged Balanced, stainless-steel clamping rings, special bearing-shaft connection
More informationE2500 Antenna Installation Instructions:
Thank you for purchasing the Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. We will also provide you with a tool that will help test the performance
More informationWow Raye Wooden Table
Wow Raye Wooden Table ssembly Instructions - Please keep for future reference 3/5837 345/6307 imensions Width - 8cm epth - 75cm Height - 73cm Important - Please read these instructions fully before starting
More informationProCurve 7 dbi Dual Band Directional antenna
GROUNDING System grounding and lightning protection are essential, especially for exterior-mounted antennas exposed to the elements. Never install an antenna where it may fall and contact electrical lines
More informationFIRST EDITION : FEB J : JUN. 6,2001. PUB. No. OME MODEL1731 MARK-3 ( HIMA) A ll rights reserved. Your Local Agent/Dealer
C Your Local Agent/Dealer 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 A ll rights reserved. Printed in Japan FIRST EDITION : FEB. 1997 J : JUN. 6,2001 ( HIMA) PUB.
More informationUnderwater GPS User Manual
Underwater GPS Document number W-DN-17002-3 Project Classification - Rev Prepared by Checked by Approved by Short description 1 2017-08-03 T. Trøite O. Skisland T. Trøite Initial 2 2017-08-04 T. Trøite
More informationXTOP PRO FLIGHT PANEL
XTOP PRO FLIGHT PNEL 5.6.2011 PRTS FOR THE XTOP [ FRONT ] 20 19 18 17 16 15 01. Glare Shield [black/gray] 02. Speakers [left/right] 03. Sound system on/off led [yellow] 04. Sound system on/off [2.1 system]
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationQDV120 Operation and Pointing manual
QDV120 Operation and Pointing manual MPAD1 Plus OP-080316-E1 page 1 Contents Item Description Page 1.0 Health and Safety for Operators and Installation Staff 3 2.0 Transit case Reflector/Mount/BUC/LNB
More informationSpecification. Spartan MA650.A.AB.002
MA650.A.AB.002 on ground-plane Spartan MA650.A.AB.002 Specification Part No. Product Name Feature MA650.A.AB.002 Spartan 2in1 MA.650 with 10M cable length Low Profile Screw Mount (Permanent Mount) GPS/GLONASS
More informationWelding Thunder 2015 Fold-and-Go Picnic Table
Welding Thunder 05 Fold-and-Go Picnic Table DRWN James Veldhuis 8/0/05 rizona Western College Q PPROVED SCLE / TableFrameWithRecievers SHEET OF CUT LIST QUNTITY DIMENSION " Tubing.05 Wall 9" " Tubing.05
More informationHow To Install Weather Pack Bulkhead Wire Connectors
How To Install Weather Pack Bulkhead Wire Connectors Weather Pack wire connectors are the premium line of environmentally sealed connectors from Delphi/Packard. The bulkhead series creates a secure and
More informationFor all Davis weather consoles including Vantage Pro2,
USR MANUAL Universal Shelter For all Davis weather consoles including Vantage Pro2, Vantage Pro2 Plus R, Vantage Vue, nvoy 8X, and Weather nvoy Product Number 6618 R Davis Instruments, 3465 Diablo Avenue,
More informationCNC Router Parts PRO Machine Kit Cable Track Installation Instructions
1 1 X CABLE TRACK TRAYS & BRACKETS The cable track on the side of the system is supported by a metal tray (or multiple trays for longer systems such as a PRO4896). These trays hang from brackets on the
More informationB6300VB-207, 3, V Ball Control Valve Carbon Steel Body, Hardened Chrome Plated, Stainless Steel Ball and Stem
6300V-207, 3, V all ontrol Valve arbon Steel ody, Hardened hrome Plated, Stainless Steel all and Stem Product eatures ast quarter turn open or closed operation, Stainless steel ball and stem, Positive
More informationProjector Flush Mount
Projector Flush Mount ABtUS SIGAPORE PTE LTD Model: AV819 www.abtussingapore.com Patent Pending Revision 21/05/2012 ABtUS SINGAPORE PTE LTD www.abtussingapore.com User Operation Guide IMPORTANT NOTES Thank
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More information11 GHz FDD Licensed Backhaul Radio. Model: AF 11FX
11 GHz FDD Licensed Backhaul Radio Model: AF 11FX 11 GHz FDD Licensed Backhaul Radio Model: AF 11FX Introduction Thank you for purchasing the Ubiquiti Networks airfiber AF 11FX. This Quick Start Guide
More informationConnecting the Radio:
Connecting the Radio: Step 1: Connect the Cat5 cable from the radio into the RJ-45 jack marked CPE on the POE injector. The POE injector is not weather proof and should be installed indoors. Step 2: Connect
More informationSpecification. Hercules MA520.A.BC.008
MA520.A.BC.008 on ground-plane Hercules MA520.A.BC.008 Specification Part No. Product Name MA520.A.BC.008 Hercules 2in1 Cellular and Wi-Fi Heavy Duty Screw Mount Antenna - Cellular 2G/3G HSPA/GSM/GPRS/CDMA/EVDO/UMTS/WCDMA
More informationCoco Storage Bunk. Code: 3327 IMPORTANT-READ CAREFULLY-RETAIN FOR FUTURE REFERENCE. 3. Attach the Drawer Base. 4. Fit the Castors.
3. ttach the Drawer ase. You need: 7 Screws for arcass (35mm) and a Screwdriver. Ensure the Drawer frame is square and carefully fit the Draw ase. The lip of the ase locates into the groove on the back
More informationINSTALLATION GUIDE P57T15 PARTITION CURRENT TAHOE. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE PT PRTITION 0 - URRENT THOE STRONG RELILE SEURE pro-gard.com 00.0.0 THESE OMPONENTS RE REQUIRE TO INSTLL THE PRTITION Hardware Kit Wing Kit PXXT PK WKT I. The following tools will be required
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationHEAVY DUTY WEIGH FEET KIT. Installation Instructions
HEAVY DUTY WEIGH FEET KIT Installation Instructions PUBLISHED BY Gallagher Group Limited Kahikatea Drive, Private Bag 3026 Hamilton, New Zealand www.gallagher.co Copyright Gallagher Group Limited 2010.
More informationINSTALLATION INSTRUCTIONS
INSTLLTION INSTRUTIONS For 12' Tall x 14' Wide x 35' Deep atting age Your batting cage frame kit comes with the following: (4) Three-Way orner Fittings (2) Four-Way orner Fittings (6) Ground Sleeves (20)
More informationBRU-100 Physical Installation
APPENDIX B BRU-100 In This Appendix: Warnings and Cautions, page 50, page 51 Check List, page 57 This appendix provides guidance for the physical installation of the BRU-100 Remote Unit at a subscriber
More informationTable of Contents 1 The digital satellite tracking system Installation Control elements Operation...15
Table of Contents 1 The digital satellite tracking system...4 1.1 EPAK -SatCom system overview...5 1.2 Safety recommendations...6 2 Installation...7 2.1 Standard delivery...7 2.2 Installation overview...7
More informationRB50/60 Radar ctr box w/antennas
INSTALLATION MANUAL RB50/60 Radar ctr box w/antennas 20222428 / B English Chapter 1 General Descriptions Contents Page No. 1.1 Inspections of the delivered goods... 1-1 1.2 Checking the Power Supply Voltage...
More informationCP6 6 Band Trap Vertical 80-6m
CP6 6 Band Trap Vertical 80-6m Instruction Sheet The CP6 is a multi-band trap-vertical antenna for HF bands, covering the 80*, 40, 20, 15, 10m & 6m amateur bands. Made from heavy duty aluminum, the CP6
More informationWave Bike Rack specs SPECS AND INSTALL INSTRUCTIONS. Deluxe Wave Style Bike Rack. Series Names & Model # s. Product maintenance. Thermoplastic Coating
SPES ND INSTLL INSTRUTIONS Deluxe Wave Style ike Rack SKU: Series Names & Model # s 8 F7WIRQ InGround Post Mount Wave ike Racks Wave ike Rack specs KP/G3, KP/G5, KP/G7, KP/G9, KP/G11, KP/G13 Plate Surface
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationPD30ETD10xxSA. Photoelectrics, Diffuse reflective. Main features. Description
Photoelectrics, Diffuse reflective Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments. They are designed for use in
More informationTownhouse Bookcase. Thank you for shopping with GLTC, we hope you enjoy having this product in your home.
Thank you for shopping with GLT, we hope you enjoy having this product in your home. www.gltc.co.uk Townhouse ookcase We know assembling furniture, toys or accessories is not everyone s favourite way to
More informationScan Sat Network S.L.
Scan Sat Network S.L. IPTV Issue Solver Guide No Signal on the screen with IPTV. My IPTV channels are stopping. My Radio is not working I don t get any sound on my channels No Signal on the screen with
More informationBollard Chain Eye 3/8" (Powder Coated) Quick Link Connector 5/16" (Powder Coated) Optional Accessories:
ollard R-98 General escription: 0 / R-98 Solar Light ollards increase safety and visibility for High-capacity batteries allow lights to operate for days hoose from a range of custom lighting colors, distribution
More informationAIT2000 CLASS B AIS TRANSPONDER
IMPORTANT NOTE The USB cable of the AIT2000 is designed to be used for configuring/programming the unit during installation and not for permanent connection to the boat s Navigation PC. If you intend to
More informationPHALCON 2000 Installation Guide
PHALCON 2000 Installation Guide PHAROS MARINE 1999 The copyright in this document is vested in AB Pharos Marine Ltd. and the document is issued in confidence for the purpose only for which it is supplied.
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationBB1068 / BB1099 SERIES
068 / 099 SRIS LL RING TMPLT UTT HINGS HVY WIGHT Non-handed ase material: steel for series 068, stainless steel for series 099 High grade plated finishes Standard non-rising non-removable pin (NRP) Standard
More information