AAE Model No. PVS-HSX High School Premier Pole Vault Standards

Transcription

1 E Model No. PVS-HSX High School Premier Pole Vault Standards luminum thletic Equipment 1000 Enterprise rive, Royersford, P Toll Free: (800) Fax: (610)

2 PVS-HSX - Premier Pole Vault Standards (High School) Standard Features and Specifications Offset rm ap Heavy-duty HPE (top and bottom) Standard Upright ap Heavy-duty UHMW djustment Post ap Heavy-duty HPE 1" Spacing b/w offset arm pins Offset rm 1-1/4" dia. heavy wall aluminum tube, 6061T6 welded one-piece powder-coated high-visibility yellow Scale ecal Measures feet/inches and metric up to 1'-0" or 6.4M high, clear vinyl w/ black print Standard Upright ustom luminum Extrusion, 6061T6, powder-coated silver djustment Knob -1/" dia. ergonomic star pattern grip, rubber-coated black w/ threaded male insert ETIL SLE 1 : 5 10'-0" High ETIL SLE 1 : 5 Offset rm Pins 1/" dia. luminum, 6061T6 w/ threaded female insert and 1/4" stainless steel bolt attachment Standard Upright Support luminum 6061T6, fully welded reinforcement both sides of upright to mounting plate djustment ody ustom luminum Extrusion 6061T6, black vinyl coating Standard djustment Post 1-3/4" dia. heavy wall aluminum tube, 6061T6 djustment ase 18"sq. x 1/4" thick 36 HRS, powder-coated dark grey ETIL SLE 1 : 5 ETIL E SLE 1 : 5 Standard Upright Mounting Hardware 3/8"-16 stainless steel bolts w/ ss locknut Standard Upright Mounting Plate luminum 6061T6, 1/4" thick material w/ mounting holes opyright ase Wheels High Performance rubber wheels, grey 01 luminum thletic Equipment o. ETIL SLE 1 : 5 Wheel xle 1/" dia. stainless steel with 3/8" thread luminum Runway Frame Model No. RF-5 ustom luminum Extrusion, 6061T6, with 1/4" thick welded mounting straps ESRIPTION: NOTE: MOEL: luminum thletic Equipment 1000 Enterprise rive, Royersford, P Toll Free: (800) Fax: (610) PVS-HSX - Standard Features and Specifications Upright Standards Meet and/or Exceed all NFHS Specifications TEGORY: PVS-HSX USTOMER 0/09/1 WN. Y: FILE: WG. NO. RP PVS-HSX Packet PVS-HSX TE:

3 PVS-HSX - Premier Pole Vault Standards (High School) ssembly ESRIPTION: luminum thletic Equipment 1000 Enterprise rive, Royersford, P Toll Free: (800) Fax: (610) PVS-HSX - ssembly NOTE: High School Premier Pole Vault Standards opyright 011 luminum thletic Equipment o. 11 MOEL: WN. Y: RP PVS-HSX FILE: TEGORY: PVS-HSX Packet USTOMER TE: 0/09/1 WG. NO. PVS-HSX--00

4 PVS-HSX - Premier Pole Vault Standards (High School) Plan View Layout oncrete base 18'-6" L to L 16'-8 1/" oncrete base 16'-6" 14'-" L to L 57" 4" Offset rm 3" 5" 10" 4" 1 1/" The 0" mark on the runway frame must be in line with the inside edge of the bault box Vault ox & Vault ox ollar (Sold Separately) Notes: imensions listed are for 1'-6" wide E pits only. onsult E for different width pits. Runway frame must be anchored to concrete base opyright NOT LL RWINGS TO SLE 01 luminum thletic Equipment o. ESRIPTION: NOTE: MOEL: luminum thletic Equipment 1000 Enterprise rive, Royersford, P Toll Free: (800) Fax: (610) PVS-HSX - Plan View Layout High School Premier Pole Vault Standards TEGORY: PVS-HSX USTOMER 0/09/1 WN. Y: FILE: WG. NO. RP PVS-HSX Packet PVS-HSX TE:

5 PVS-HSX HIGH SHOOL PREMIER POLE VULT STNR PRTS LIST Pt.# Item escription Qty. 1 Inner Tube 1-3/4" dia. x.100 wall x 10 lg. 6061T6 aluminum tube Offset rm 1-1/4" x.15 wall x -1/ X T6 luminum stay, U shape 3 End ap -1/" x 3" x 1/4" cast aluminum end cap 4 Outer Tube " x 5" x.150" custom aluminum extrusion, 6063T6, 10-0" lg. 5 H-pad luminum "H" adjustment pad, cast 6 Slider luminum rectangular adjustment body, cast 7 Knob 1-7/8" dia. x 3/8"-16 x 1" adjustment knob, 9 series, ribbed 9 Nut 3/8-16 nylon-insert lock nut, SS rossbar Pin 1/" dia. x 4-1/" lg. aluminum rod, 1/4"-0 tapped end 8 11 ase Steel base 13 Washer 1/4-0 washer, SS 14 olt 1/4"-0 x 1/" hex bolt, SS 4 15 Loop Velcro Loop, adhesive back, 1" x 5" 4 16 ap Plastic cap, aplug #17-S 17 olt 1/4"-0 x -1/" socket cap screw, SS 4 18 onnector 1-1/4" metal tube connector, 1/4"-0, gage 4 19 olt 3/8"-16 x steel hex bolt, SS 8 0 Washer 3/8" flat washer, SS 8 1 oncrete nchor 3/8"-16 x ouble expansion shield 8 4 olt 3/8-16 x 1 steel hex bolt, SS 5 Runway Frame Welded aluminum runway frame, -1/" wide x 5" lg., w/ decal 6 olt 5/16-18 x 3/4" hex bolt, SS 4 7 Nut 5/16-18 wiz-lock nut, SS 4 8 Wheel 1 5/8 High performance rubber wheel 8 9 xel olt Machined bolt, 1/ dia. x 1 1/ unthreaded axel and 3/8 dia. x 3/4 threaded end; accepts 1/ open wrench or adjustable wrench for tightening 8 Note: Starting in 011, the ase Glider ssembly (Item Nos., 3, & 4) has been replaced with the Roller Wheel ssembly (Item Nos. 9, 8, & 9). The Roller Wheel ssembly can be purchased to replace old ase Glider ssemblies FOR TEHNIL SSISTNE, LL K:\E ata\product Instructions & Parts Lists\PVS-HSX\PVS-HSXParts List 011.doc opyright 011 luminum thletic Equipment o. Page 1 of 1

6 PVS-HSX HIGH SHOOL PREMIER POLE VULT STNR INSTLLTION N OPERTION INSTRUTIONS Please note: These instructions are for 1-6 wide E pits only. Please consult E, or make the necessary adjustments for different width pits. INSTLLTION: Refer to rawing No. PVS-HSX--003 (oncrete Pads for Runway Frames) 1. Locate proper location of concrete pads to be poured that will anchor the PVS-HSX runway frames (Item No. 5).. ig two holes approximately 30" x 66" x 6" deep and 16'-6" apart (18-6 on center). (onsult local building codes for concrete depth and drainage requirements.) 3. Make () wooden concrete forms 4" x 57" (inside dimensions) around the openings. Make the forms level and flush with the ground. Pour the concrete into the forms, making sure the concrete is level with the ground. 4. fter the concrete has hardened, locate runway frames (Item No. 5) in their proper location: / apart (18-6 on center), centered on each pad. Runway frames should have the "0" mark in line with the top inside edge of the vault box, (inside edge closest to the rear of the landing pit). Once proper location has been established, mark hole locations for fixing runway frames to the pads. 5. Remove frames. Using a 3/4" Masonry rill it, drill a hole deep. Using a hammer, tap 3/8-16 x ouble Expansion Shield (Item No. 1) in with threaded side down, flush with concrete surface. SSEMLY: 1. olt runway frames to concrete pads using 3/8"-16 x " hex bolts (Item No. 19) and 3/8" flat washers (Item No. 0). Note: Each runway frame must be bolted into the concrete in all 4 bolting locations. Re-check all bolts for tightness.. ttach four (4) roller wheels (Item No. 8) to base (Item no. 11) using machined axel bolts and 3/8"-16 serrated hex nuts (Item Nos. 9 & 9). Refer to rawing No. PVS-N--00. Repeat procedure for the other base. 3. ttach offset arm (Item No. ), to Inner tube (Item No. 1) using 1/4"-0 x 1-1/" socket cap screws (Item No. 17). Repeat procedures for other upright. 4. ttach crossbar pins (Item No. 10) to offset arms (Item No. ) using 1/4"-0 x 1/" hex bolts (Item No. 14) and 1/4 washers (Item No. 13). There are 4 crossbar pins for each offset arm. 5. ttach completed main upright assembly to base (Item No. 11) using 3/8-16 x 1 hex bolts and 3/8-16 serrated hex nuts (Item No. 4 & 9). Repeat procedure for other upright & base. Page 1 of

7 PVS-HSX HIGH SHOOL PREMIER POLE VULT STNR INSTLLTION N OPERTION INSTRUTIONS 6. Slide completed units into their respective frames. Offset arms should face towards the center of the pit with the adjustment knob on the outside of the pit and the crossbar pins pointing away from the runway. OPERTION: 1. The PVS-HSX Premier Pole Vault Standard is designed to measure jumps from 7'-0" - 19'-0". The lowest reading on the adjustment scale is 10'-0". The 10'-0" reading is used with the crossbar located on the top crossbar support pin. To obtain a 7'-0" measurement, move the crossbar down to the lowest crossbar pin position. Likewise, a 19'-0 reading would be taken when the reading on the scale was 19'-0" and the crossbar was on the top crossbar pin.. Pole Vault standard may be adjusted manually by loosening adjusting knob (Item No. 7) and raising or lowering the upright to the desired height. Pole Vault standard may also be adjusted in a 1'-0" increments by moving crossbar from pin to pin. (rossbar pins are 1" apart.) RE N SPEIL INSTRUTIONS: 1. t the end of the season, as well as after each event (dependent upon the risk of vandalism or injury), the upright assemblies should be removed and the runway frames unbolted and removed for storage. Frequent storage and proper care of the PVS-HSX will greatly improve the life and functionality of the unit.. While the PVS-HSX is in use, the runway frame must be bolted into the concrete for safety of the participants as well as for proper operation. 3. Properly installed, the PVS-HSX can be adjusted laterally from 15-1/ 30 (with 0 being the inside edge of the vault box) away from the vaulter. FOR TEHNIL SSISTNE, LL K:\E ata\product Instructions & Parts Lists\PVS-HSX\PVS-HSX ssembly Instructions 011.doc opyright 011 luminum thletic Equipment o. Page of