Installation and Assembly: Flat-Panel Base Lock-Down Kit for Samsung Display Models
|
|
- Lambert Moore
- 5 years ago
- Views:
Transcription
1 Installation and ssembly: Flat-Panel Base Lock-own Kit for Samsung isplay Models Models: HLG452-SM, HLG452-SM-Q10 Maximum isplay Size: 100 lb (45.35 kg) 3215 W. North ve. Melrose Park, IL (800) or (708) Fax: (708)
2 Note: Read instruction sheet before you start installation and assembly. Parts may appear slightly different than illustrated. Parts List HLG452-SM HLG452-SM-Q10 escription qty part # qty part # lock-down plate B adhesive strip /4-20 x 1 3/4" carrage bolt /4-20 sloped nut e plastic cap F rubber pad - 3/16 x 1" x 3/4" G # 10 x 3/8 phillips pan TEk screw H M4 x 16 phillips pan trilobe screw I M4 x 16 security screw J 4mm security allen wrench B E F G H I J Tools Needed for ssembly drill 1/4" drill bit 5/8" open box wrench phillips screwdriver 3M Rubber & Vinyl 80 Spray dhesive (generic name: ontact 80 Neoprene Vinyl Spray dhesive) This product can be found at hardware and craft stores, as well as on the 3M website: ccessory 939-1/4-20 x 2 1/4" replacement carriage bolts (ontact ustomer Service) Installation Template (plate only) Installation Option 1 (Fasteners) Pages 3 and 4 Installation Option 2 (dhesive Strips) Pages 5 and 6 Installation of Security Screws for Base/Screen ssembly Page 7 2 of 7
3 Installation Option 1 (Fasteners) ISPLY MOEL HOLE PTTERNS SMSUNG LN-T2353HTX LN-T2653HTX LN224501HX2 LN264501HX2 LN-T3253HTX LN-T4053HTX LN324501HXZ LN374501HXZ LN404501HXZ LN326501HXZ LN406501HXZ LN466501HXZ LN526501HXZ LN32B4506HXZ LN32B4576HXZ LN37B4576HXZ LN40B4576HXZ (4) # 10 x 3/8 phillips pan screws (self drillers) (G) (4) # 10 x 3/8 phillips pan screws (self drillers) (G) Note: Mounting hole bumpout must be placed on bottom flush with raised section on base. 1 Use lock-down plate () as a template to mark location of holes, point 1 and point 2, approximately 7" apart on table. rill two holes using a 1/4'' drill bit. 2 Slide two 1/4-20 x 1 3/4" bolts () through slots as shown below. NOTE: 2 1/4" carriage bolts (939) are available for use with thicker mounting surfaces. 7" POINT 1 (178 mm) POINT 2 TBLE TOP Skip to page five for Installation Option 2 (dhesive Strips) 3 of 7
4 3 ttach lock-down plate to display base bottom using screws provided. Refer to page three for lock-down plate/ display base stand hole pattern. NOTE: Remove existing rubber feet from display base that interfere with the lock-down plate. Larger display bases may require additional rubber pads (F) to provide additional support at the perimeter of the base. ISPLY BSE STN RUBBER FEET SREWS PROVIE NOTE: isplay base stand and mounting hole locations may appear different than illustrated. Mounting Lock down Slope Nuts 4 Hand tighten slope nuts () onto two of the 1/4-20 x 1 3/4" screw bolt () until snug against bottom of table as shown in etail 1. Thread another slope nut () upside-down, about two turns from first slope nut () as shown in etail 2. Insert a 5/8" open box wrench between both slope nuts () and tighten as shown in detail 3. fter slope nut is secure remove bottom slope nut and add plastic cap (E) as shown in figure 4.1. Repeat with remaining 1/4-20 x 1 3/4" screw bolt (). etail 1 BOTTOM OF ESK etail 3 NOTE: void jamming both slope nuts (G) together, doing so may make it difficult to remove slope nut used for tightening. fter slope nut is secure remove bottom slope nut. etail 2 LEVE SPE IN BETWEEN SLOPE NUTS BOTTOM OF ESK TIGHTENING SLOPE NUT (F) E TIGHTENING SLOPE NUT () 5/8" OPEN BOX WRENH FIG of 7
5 Installation Option 2 (dhesive Strips) ISPLY MOEL HOLE PTTERNS SMSUNG LN-T2353HTX LN-T2653HTX LN224501HX2 LN264501HX2 LN-T3253HTX LN-T4053HTX LN324501HXZ LN374501HXZ LN404501HXZ LN326501HXZ LN406501HXZ LN466501HXZ LN526501HXZ LN32B4506HXZ LN32B4576HXZ LN37B4576HXZ LN40B4576HXZ (4) # 10 x 3/8 phillips pan screws (self drillers) (G) (4) # 10 x 3/8 phillips pan screws (self drillers) (G) Note: Mounting hole bumpout must be placed on bottom flush with raised section on base. 1 ttach lock-down plate to display base bottom using screws provided. Refer to page five for lock-down plate/display base stand hole pattern. NOTE: Remove existing rubber feet from display base that interfere with the lock-down plate. Larger display bases may require additional rubber pads (F) to provide additional support at the perimeter of the base. ISPLY BSE STN RUBBER FEET SREWS PROVIE NOTE: isplay base stand and mounting hole locations may appear different than illustrated. 5 of 7
6 2 lean bottom of lock-down plate () with rubbing alcohol. Spray bottom of lock-down plate () only where tape will be applied, with 3M rubber and vinyl #80 spray adhesive (not supplied). Pull apart the four adhesive strips (B) and remove red backing from one side. Wait at least 4 minutes for adhesive spray to dry before applying adhesive strip (B). ttach adhesive strips (B) firmly to bottom of lock-down plate () as shown below. lean with rubbing alcohol ried 3M rubber and vinyl #80 spray adhesive B 3 lean desk surface with rubbing alcohol. Use 3M rubber and vinyl #80 spray adhesive (not supplied) on the mounting surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before removing tape backing from lock-down plate () and placing firmly on surface. NOTE: There is a recommended 72 hour cure time for tape on lock-down plate (). Note: Once tape backing is removed be careful not to touch the sticky surface of the tape with fingers, as this can cause the tape to lose some of its holding power. NOTE: fter application of tape on lock-down plate (), the bond strength will increase as the adhesive flows onto the surface. t room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% after 24 hours, and 100% after 72 hours. In some cases, bond strength can be achieved more quickly by exposure to elevated temperatures (e.g. 150 F [66 ] for 1 hour). ISPLY BSE STN ried 3M rubber and vinyl #80 spray adhesive (not supplied) NOTE: isplay base stand may appear different than illustrated. desk surface 6 of 7
7 Installation of Security Screws for Base/Screen ssembly 4 Thread two M4 x 16 phillips pan trilobe screws (H) to top display attachment holes as shown in fig Remove the two M4 x 16 phillips pan trilobe screws (H) and attach display screen to display base using two M4 x 16 mm socket pin screws (I), as shown in figure 4.2. Tighten with 4 mm security allen wrench (J). Use TV supplied screws for remaining holes. NOTE: Screws are installed at a diagonal. isplay screen isplay screen H I fig 4.1 isplay base fig 4.2 NOTE: isplay and base may appear different than illustrated 7 of , Peerless Industries, Inc. ll rights reserved. ll other brand and product names are trademarks or registered trademarks of their respective owners.
Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400
Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More informationInstallation and Assembly: Mount - Wall/Ceiling Mount
Installation and ssembly: Mount - Wall/Ceiling Mount Model: DST360 Max oad Capacity: 150 lb (68. kg) 3215 W. North ve. Melrose Park, I 60160 (800) 729-0307 or (708) 865-8870 ax: (708) 865-2941 www.peerlessmounts.com
More informationInstallation and Assembly: Wallmount for CPA100 and Whiteboard
Installation and ssembly: Wallmount for CP100 and Whiteboard Model: 100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 Visit 3215 the
More informationInstallation and Assembly: Universal Projector Wall Arm
Installation and ssembly: Universal Projector Wall rm Models: PST-2955, PST-2955-W, PST-2955, PST-2955-W Max UL Load Capacity: 35 lb (5.8 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-22 Fax: (800)
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInstallation and Assembly:
Installation and ssembly: Model: DS508 os pd For SHPD installations, please contact Peerless Customer Service for a copy of the P. Maximum Load Capacity: 200 lb (90.7 kg) 2300 White ak Circle urora, IL
More informationInstallation and Assembly - Desktop Swivel Mount For 32" - 55" Flat Panel Display
Installation and ssembly - Desktop wivel ount For 32" - 55" Flat Panel Display odels: HP455 ax Load apacity: 75 lb (34 kg) IUED: 2012-06-28 HEET #: 125-9328-4 (2017-10-20) NOTE: Read instruction sheet
More informationInstallation and Assembly: Adjustable Extension Column (Pipe) 8" - 11"
Installation and ssembly: djustable Extension Column (Pipe) 8" - 11" Model: ELPMBC01 R This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 500
More informationInstallation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays
Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 65" Plasma Screens. Models: PLAV70, PLAV70-S
Installation and ssembly - Universal rticulating Swivel Double-rm for 42" - 65" Plasma Screens Models: PLV70, PLV70-S Max UL Load apacity: 200 lb (91 kg) 2300 White Oak ircle urora, Il 60502 (800) 865-2112
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationInstallation and Assembly: Projector Enclosure
Installation and ssembly: Projector Enclosure Models: PE 1120, PE 1120-W 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708) 865-2941 www.peerlessmounts.com ISSUED: 07-11-06
More informationInstallation and Assembly: Dual-Screen Desktop Mount for 10" to 20" LCD Monitors
nstallation and ssembly: Dual-Screen Desktop Mount for 0" to 0" LD Monitors Models: LT-0 Max Load apacity: 5 lb (.3 kg) per arm 35 W. North ve. Melrose Park, L 6060 (800) 79-0307 or (708) 865-8870 Fax:
More informationInstallation Guide Tilt/Swivel Flush Mount for 23'' and Larger Flat Panel Displays
Installation Guide Tilt/Swivel Flush Mount for 23'' and Larger Flat Panel isplays WRNING: This mounting system has a weight limit of 100 lbs [45.36 kg]. o not mount a display weighing more than 100 lbs
More informationNEC Display Solutions of America, Inc.
NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NEC NP400, NP500, NP500W, and NP600 Projectors Model: NP600CM Maximum Load Capacity: 50 lb (22.7 kg) Features:
More informationInstallation and Assembly: Projector Ceiling/Wall Mount
Installation and ssembly: Projector Ceiling/Wall Mount Models:PRG-EX, PRG-EX-S, PRG-EX-W PRG-EXB, PRG-EXB-S, PRG-EXB-W PRG-EXC, PRG-EXC-S, PRG-EXC-W R This product is intended for use with UL Listed products
More informationInstallation and Assembly - Vision Point LCD Screen Pedestal Stand - 75/100 mm Adapter Plate
Installation and ssembly - Vision Point CD Screen Pedestal Stand - 75/100 mm dapter Plate Model: CS 100, CS 100S Read instruction sheet before you start installation and assembly. Maximum oad Capacity:
More informationInstallation and Assembly: Ceiling mount for LCD screens up to 29"
Installation and Assembly: Ceiling mount for LC screens up to 29" Models: LCC 18, LCC 18-S, LCC 36, LCC 36-S Patent Pending Features: Comes in two adjustable height ranges (in 1" increments): 18"-30" and
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationNEC Display Solutions of America, Inc.
NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NP-M332XS, NP-M352WS, NP-M282X, NP-M283X, NP-M322X, NP-M323X, NP-M322W, NP-M323W, NP- M363X, NP-M363W, NP-M402X,
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
nstallation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1M, SR560M R This product is UL Listed. t must be installed by a qualified professional installer. Max UL Load Capacity: 150 lb (68 kg)
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationInstallation and Assembly: Projector Ceiling/Wall Mount
Installation and ssembly: Projector eiling/wall Mount Model# Max UL Load apacity EX, EX-S, EX-W, EX, EX-S, used with PRS projector mount 25 lb (11.3 kg) EX-W, EX, EX-S, EX-W used with PRG projector mount
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstallation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays
Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationInstallation and Assembly: Ceiling mount for LCD screens up to 29"
Installation and Assembly: eiling mount for L screens up to 29" Models: L18-, L18-S, L36-, L36-S Features: omes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48" -5 to +20 adjustable
More informationINSTALLATION GUIDE. Flat Panel Arm Mount MLA100-L. VESA 100x100 compatible. Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg)
INSTALLATION GUIDE Flat Panel Arm Mount MLA100-L Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg) VESA 100x100 compatible Note: Read entire instruction sheet before you start installation and
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
Installation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1G, SR560G R This product is U isted. It must be installed by a qualified professional installer. Max U oad Capacity: 150 lb (68 kg) screen
More informationInstallation & Assembly: Two Piece Suspended Ceiling Plate
Installation & ssembly: Two Piece Suspended Ceiling Plate Model: CMJ453 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112
More informationInstallation and Assembly: Universal Projector Wall Arm
nstallation and ssembly: Universal Projector Wall rm Model: SP-WLLRM-01 SP-CEL-UNV (sold separately) Max Load Capacity:35 lb (15.8 kg) Note: Read entire instruction sheet before you start installation
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP 850, SP 850P, SP 850-S, SP 850P-S Max Load Capacity: 150 lb (68 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or
More informationMax Load Capacity: 50 lb (22.6 kg) J K
Installation and ssembly: ptoma Universal Projector Mount y Peerless Model: M-500U Max oad apacity: 50 lb (.6 kg) R This product is intended for use with U isted products and must be installed by a qualified
More informationInstallation and Assembly: DUKANE PROJECTOR SHORT THROW WALL ARM
Installation and Assembly: DUKANE POJETO SHOT THOW WALL AM Model: UST-WALLAM3 POJETO POSITION FO 60" - 70" SEEN SIZE POJETO POSITION FO 70" - 100" SEEN SIZE 430-User Guide UST-WALLAM3-00 Do not begin to
More informationInstallation and Assembly Manual: PRS, RTR Series Projector Mount
Installation and ssembly Manual: PS, T Series Projector Mount Models: PS-UNV, PS-UNV-S, PS-UNV-W PS-UNVP, PS-UNVP-S, PS-UNVP-W T-UNB, T-UNS, T-UNW This product is intended for use with UL Listed products
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More informationCottage Picket Gate. 6 in in in in
S S E M LY I N S T R U T I O N S www.newenglandarbors.com ottage Picket Gate 1.875 in 6 in 43.75 in 22.5 in 2 48.5 in Please read through before starting assembly. heck ox for These ontents (1 ox) In the
More informationNancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual
Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Thank you for purchasing our 4 Yard Option (4YO) Upgrade Kit. To install this upgrade you are simply going to assemble
More informationVINTNER WINE TOWER HARDWARE TOOLS REQUIRED COMPONENTS cam covers cams 16 - cam screws. 1 - pull small screws.
HRDWRE 16 - cams 16 - cam s 16 - cam covers 1 - pull 1 - pull bolt 40 - wood dowels 28 - small s 8 - medium s Thank you for purchasing the Vintner Wine Tower. This page lists all the contents included
More informationInstallation and Assembly: Adjustable Suspended Ceiling Channel Kit
Installation and ssembly: djustable Suspended Ceiling Channel Kit Model: CMJ500R1 C U L US This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity:
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationInstallation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS
Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand
More informationSLOANE WHITE / COBALT / CRIMSON LEANING DESK
SLONE WHITE / OLT / RIMSON LENING ESK SSEMLY HRWRE Missing hardware? Please call 800.606.6387 for replacements. 2 - large bolts 6 - small bolts 10 - wood dowels 8 - spring washers 8 - flat washers 20 -
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationAssembly and installation help
Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first
More informationMobileTrak5 Installation Instructions
MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips
More informationSLOANE DARK LEANING BOOKCASE
SLONE DRK LENING BOOKSE HRDWRE 4 - large bolts 10 - small bolts 1 - small screw 4 - medium screws 1 - large screw 2 - wall fittings 1 - wall strap 1 - plastic anchor 8 - wood dowels Thank you for purchasing
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationInstallation and Assembly: Full Service Video Wall Mount
Installation and Assembly: Full Service Video Wall Mount Model: DS-VW765-LAND Max UL Load Capacity: 125 lb (57 kg) 1 of 12 ISSUED: 05-13-11 SHEET #: 145-9011-5 05-21-12 Note: Read entire instruction sheet
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationInstallation and Assembly Manual: Vector Pro II
Installation and ssembly Manual: Vector Pro II Models: PJF2-UNV, PJF2-UNV-S R This product is intended for use with U isted products and must be installed by a qualified professional installer. Maximum
More informationB B B
Winchester SXP Gauge Tactlite Six Position Adjustable Shotgun Stock with Scorpion Recoil System B..0.00 B..0.00 B..0.00 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment
More informationInstallation & Assembly: Suspended Ceiling Kit
Installation & ssembly: Suspended Ceiling Kit Model: CMJ450 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500
More informationINSTALLATION GUIDE Ceiling TV Mount MHP-52
ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and
More informationINSTALL LOAD BED TRACKS
Universal LOAD BED TRAY & Load BArs TRBU001 / KRLBUNI1 INSTALL TIME: 2.5 Hours READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Load Bed Rack or Load Bar Kit. Your Kit will contain the
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationHONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationTOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.
TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support
More informationModels: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens Models: PLAV70-UNL, PLAV70-UNLP Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle Aurora, Il 60502
More informationTrak-Slider Instructions
Trak-Slider Instructions 1/4-20 x 3/4" Hex Head Bolt 1/4-20 Flanged Hex Nut Gusset 1/4-20 x 1/2" Allen Cap Screw 1/4-20 Nylock Nut Rivet 1/4-20 x 3/8" Pan Head Phillips Machine Screw 1/4 USS Flat Washer
More informationParts List D E. Installation and Assembly- Encore Projector Mount Protected by U.S. Patent No. 6,042,068. Model: PJRL411
nstallation and ssembly- ncore Projector Mount Protected by U.S. Patent No. 6,042,068 Model: PRL4 MPORTNT! Read entire instruction sheet before you start installation and assembly. WRNN! nstaller must
More informationWARNING. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
All-in-one Projector Adapter Plate I5300 series, I5500 series, and SP8602 series Model: SP-CEIL-ISTALL Maximum Load Capacity: 50 lbs/22 kg Read all instructions before you start installation and assembly.
More informationO W N E R ' S M A N U A L
TABLE TENNIS TABLE MODEL NOS. T861 T861B O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may
More informationRangerWare Fiberglass Door System Installation Instructions P/N
Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationFlat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold
FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination
More informationADJUSTABLE BASKETBALL SYSTEM ASSEMBLY INSTRUCTIONS AND OWNER'S MANUAL
IRONCLAD SPORTS, INC HIGHLIGHT HOOPS ADJUSTALE ASKETALL SYSTEM ASSEMLY INSTRUCTIONS AND OWNER'S MANUAL MODEL: HIL885!! WARNING FAILURE TO COMPLY WITH ANY OF THE WARNINGS IN THESE INSTRUCTIONS MAY RESULT
More informationIN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.
Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.
More informationFranklin Mills Stackable Movable Lateral Instructions
Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11
More informationCopyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax
Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2
More informationGeneral Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized
General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium
More informationAndyMark DART 12.
AndyMark DART 12 Part Number Description QTY These Parts Are Pre-Assembled by AndyMark am-0031 Bearing, 3/16"ID (R3) 1 am-0209 Bearing, 3/8"ID 1614ZZ 2 am-1028 Screw, #10-32x3/8 Pan Head Philips 8 am-1121
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationHQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750
HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 Important Note: Upgrading the track system on the HQ Studio Frame requires the use of this 2 Extension Kit (Part #QF09750),
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationInstallation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe installation of MP40/50/60/70 mounting equipment on the anesthesia machine.
More informationSapper XYZ Monitor Arm Installation Instructions
9/5/2012 Sapper XYZ Monitor rm Installation Instructions 5900800 Step 1: ttach Mount to Work Surface Two-Piece Table lamp and eep Table lamp llen wrenches (in inches): lamp lower to upper jaw 5/32 () lamp
More informationCottage Picket Gate A S S E M B LY I N S T R U C T I O N S
S S E M LY I N S T R U T I O N S ottage Picket Gate 1 7/8 6 43 3/4 22 1/2 48 1/2 Please read through before starting assembly. heck ox for These ontents (1 ox) In the event of missing or defective parts
More information