BBULTRA Basketball Tower Installation

Size: px

Start display at page:

Download "BBULTRA Basketball Tower Installation"

Oswald Johnson
5 years ago
Views:

Ph: 1300 500 314 Basketball Tower Installation Thank you for your purchase of the Ultra adjustable Basketball system.

This guide will provide information on the proper assembly and installation methods, operating procedures, and preventative maintenance of your system.

No one under the age of 18 should attempt assembly or set up of the unit, unless properly supervised.

1 Ph: Basketball Tower Installation Thank you for your purchase of the Ultra adjustable Basketball system. To ensure that our equipment will provide years of use to you, we are including this installation, operation, and maintenance guide. This guide will provide information on the proper assembly and installation methods, operating procedures, and preventative maintenance of your system. It is recommended that an individual who has been properly trained perform assembly and set up of the backstop. No one under the age of 18 should attempt assembly or set up of the unit, unless properly supervised. To prevent normal wear and tear from shortening the life of the unit, preventative maintenance inspections and repairs should be performed at least once per year. If the units are subject to high or unusual usage, inspections should be scheduled to occur more frequently. If items are found to be nonconforming, replacements can be ordered from one of our authorized dealers. Read and understand the following warnings to prevent possible personal injury and potential damage to the equipment during assembly, setup, and operation. Before proceeding with assembly, read all instructions and assembly procedures. Make sure all parts have been received and are not damaged. SAVE THESE INSTRUCTIONS FOR FUTURE USE 1

2 Parts Checklist Verify all parts listed on packing list are present prior to installation. The following parts have been packed separately Please refer to your packing slip to verify the correct board and goal has been received. Item Basic Items Qty x 5.0 Base weldment (mast) 1 2 Lower extension arm, welded 1 3 Upper extension arm assembly 1 4 Actuator brackets (plates) 2 5 Actuator, Height adjustment device 1 6 Actuator tension arm 1 7 Not supplied with this system - 8 Glass backboard 1060 x 1525 mm 1 9 Rim (1000 Breakaway Goal) 1 10 Net 1 Optional Padding 11 LSCE60 Pro Mold recreational backboard padding 1 12 PP5SQF Fitted pole pad 1 13 PP6WR Wrap-Around pole pad 1 14 BP5SQ Base pole pad 1 Template Plate & Base Mounting Hardware 15 Template plate 1 16 U-bolt, 3/4 dia. x 18 long 2 17 Hex nut, 3/ Flat washer, 3/ Split lock washer, 3/ Rebar 36 long 4 Actuator Bracket Hardware 21 Hex bolt, 16mm dia. x 180mm long 2 22 Hex bolt, 16mm dia. x 130mm long 1 23 Hex nut, 16mm 2 24 Nylon locking nut, 16mm 1 25 Flat washer, 16mm 6 26 Split lock washer, 16mm 2 27 Plastic washer, 16mm 2 2

3 Lower/Upper Extension Arm & Tension Arm Hardware 28 Hex bolt, 18mm dia. x 310mm long 2 29 Hex bolt, 18mm dia. x 235mm long 1 30 Nylon locking nut, 18mm 3 31 Flat washer, 18mm 6 32 Plastic bushing, 18mm 6 33 Hex bolt, 14mm dia. x 90mm long 1 34 Nylon locking nut, 14mm 1 35 Flat washer, 14mm 2 36 Upper arm spacer bracket 2 37 Hex bolt, 12mm dia. x 55mm long 8 38 Hex nut, 12mm 4 39 Flat washer, 12mm Split lock washer, 12mm 4 Backboard Mounting Hardware 41 Nylon locking nut, 12mm 4 42 Plastic bushing, 12mm 4 Rim (Goal) Hardware 43 #3/8-16 x 2 long hex bolts 4 44 #3/8-16 nut /8 flat washer /8 split lock washer 4 47 #10 x 1/2 self-tapping TEK screw 4 INSTALLATION INSTRUCTIONS Tools and Materials Required for Assembly: 1. 2 Adjustable Wrenches. 4. 9/16 Wrench /8 Wrench 7. Phillips Head Screwdriver 8. Electric Drill 9. 4 mm Drill Bit 10. Tape Measure 11. Hammer or Mallet 12. Sho vel 13. Post Hole Digger. 14. Carpenter s Level Ladders minimum 16. Concrete bags of pre-mix 3

4 4

5 Use the illustration below to dig and prepare the hole for anchoring the template plate & U-bolt assembly. Check is soil conditions are appropriate for footing before installing system. 5

6 Set the U-bolt assembly in the concrete as shown below. 6

7 Raise and place the main column over the U-bolts as shown below. The column is heavy. Use at least two people for this operation. Follow the steps to select the correct nuts and washers. If the column is not exactly vertical, adjust the bottom nuts to make a level base. When the column is vertical, tighten all nuts securely. 7

8 Follow the steps below to assemble the unit in the proper sequence. See the instructions on the following pages for more detailed information. 8

9 STEPS 1 & 3: Use the indicated hardware to assemble the actuator plates (4) to the main post (1). Also attach the crank end of the height actuator (5) to the plates. Tighten the hex nuts (23) securely. The nylon locking nut (24) should be snug but not over tight to allow rotation of the actuator. 9

10 STEPS 2 & 3: Attach the lower extension arms (2) and the actuator tension arm (6) using the indicated hardware. The 18mm plastic bushings (32) must be inserted first as shown. Nylon locking nuts (30) should be snug but still allow movement. 10

11 STEP 4: Assemble and attach the upper extension arms using the indicated hardware. Be sure to insert the 18mm plastic bushings (32) where shown. The nylon locking nut (30) should be snug but still allow movement. The 12mm nuts (38) should be tightened securely. 11

12 Attach the top of the Actuator device to the bottom of the Tension arm using the indicated hardware. Note: The goal height is adjustable from 2300 mm to 3050 mm 12

13 STEP 5: Attach the backboard with the 12mm hardware as indicated below. It is easiest to mount the board with the supporting arms in the full down position. *Helpful hint; Working out of the bed of a truck may be easier than using ladders. The backboard is very heavy. Note: Install the plastic bushing (42) where shown. Make sure that you have enough help to complete this operation safely! 13

14 STEP 6: Attach the goal with 3/8 (9 mm) hardware as shown below. 14

15 The following illustration shows how to attach the LSCE60 Pro Mold Recreational Backboard Padding (if purchased). The padding may be attached before or after the backboard has been mounted in final position. 15

16 Note: The padding options shown below are purchased separately. 16

17 17

Super Shot Adjustable Basketball System

Super Shot Adjustable Basketball System Model: GP5A48 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION