INSTRUCTION MANUAL LCD TV BRACKET WM-3968

Size: px

Start display at page:

Download "INSTRUCTION MANUAL LCD TV BRACKET WM-3968"

Cory Simon
5 years ago
Views:

instruction manual carefully before using, and keep it for future

1 INSTRUCTION MANUAL LCD TV BRACKET WM-3968 DEAR CUSTOMER In order to achieve the best performance of your product, please read this instruction manual carefully before using, and keep it for future reference. If you need extra support, please write to P-1

2 IMPORTANT: Ensure you have received all parts against the component checklist prior to installing.if any parts are missing or faulty, telephone the special franchiser for a placement. Do not begin to installation of the product on you have read and understand the instructions and warnings contained in this Installation Sheet. If you have any question regarding any of the instruction or warning, Please contact your local distributor. Please refer to manufacturer s installation guide recommendation for required distance from to avoid risk of property damage. This product should only be installed by someone of good mechanical aptitude, with experience and basic building, and fully understands. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Package M mount (x1) A 3mm Allen key (x1) B Never exceed the Maximum Load Capacity. (20kg/44lbs) If mounting to wood studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge to edge stud finder is highly recommended. M4x14 (x4) M-A M5x14 (x4) M-B M6x14 (x4) M-C M8x20 (x4) Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power. This products intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. D 5 washer (x4) D8 washer (x4) small spacer (x8) M-E Package W ST 5.5x50 lag bolt (x3) concrete anchor (x3) W-B P-2 Tools required Phillips Head Screw driver(200mm length exclude the handle) Electric drill and 8mm masonry bit for concrete installation Marking Pen Hammer P-3

3 1 Separate VESA Plate from the Wall Mount: Stud Loosen fig a WOOD STUD WALL MOUNTING: 2b SOLID BRICK AND CONCRETE BLOCK MOUNTING: Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws firmly, but do not over tighten. Over tightening can damage the screws, greatly reducing their holding power. Make sure that mounting screws are anchored into the center of the studs. Use of an edge to edge stud finder is highly recommended. Hardware provided is for attachment of mount through standard thickness dry or plaster into studs. Installers are responsible to provide hardware for other types of mounting situations. When installing mounts on cinder block, verify that you have a minimum of 1-3/8 of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1 minimum from the side of the block. It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud s center. Place plate on as a template. And mark the center of the three mounting holes. Make sure that the mounting holes are on the stud centerline. Drill three 1/8 (3mm) dia. Holes 1.2 (30mm) deep. Make sure that the plate is level, secure it using three wood screws () as shown in fig P-4 Use the Wall Plate as a template to mark 3 holes locations on the, as shown in fig.2.2. Pre-drill these holes with a 8mm masonry bit to at least 50mm in depth. Insert a Concrete Anchor (W-B) into each of these holes. Attach the Wall Plate to the using 3 wood screws () as shown in fig.2.3. P-5

4 M-E W-B M-A M-B M-C or fig. 2.2 fig. 3.2 fig Installing the Display 3 Installing Adapter Bracket To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. Place the adapter bracket on the back of screen, align to holes, as shown in fig.3.1 Attach the adapter bracket to the back of the screen using appropriate combination of washers and screws. as shown in fig.3.2 Slide the head of VESA plate along VESA plate mount rail until it snug fits into the VESA plate mount. Then tighten screws(just removed) by hand. as shown in fig.4.1 Tighten by hand fig. 3.1 P-6 fig. 4.1 P-7

5 5 Adjustment It is necessary to slightly loosen or tighten the adjustment screws using a supplied Allen key according to the different weight of display. as shown in fig.5.1. B fig Adjust to desired location or tilt. fig. 5.2 Maintenance Check that the bracket is secure and safe to use at regular intervals(at least every three months). Please contact your dealer if you have any questions. P-8

Full-motion Wall Mount

Full-motion Wall Mount MD120409-01 AWM1521- AU Safety Instruction Component Checklist WARNING IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing.