Flat Panel Mobile Cart and Accessories

Size: px

Start display at page:

Download "Flat Panel Mobile Cart and Accessories"

Amice Hodge
5 years ago
Views:

1 INSTALLATION MANUAL Flat Panel Mobile Cart and Accessories Optional Accessories TCH01 TDV01 TLP01 TCR01 Note: The accessories are not standard. The accessories will be selected according to user requirement. CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! All accessories 200x200/300x x200/400x x400 60" MAX 60kgx2 (132lbsx2) RATED 10kg (22lbs) RATED

2 NOTE: Read the entire instruction manual before you start installation and assembly. WARNING Component Checklist IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement. Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. base (x1) A column (x1) B This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. wheel caster/brake (x2) C wheel caster (x2) D cable clip (x6) E Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. fixing piece (x1) F top cover (x1) G big universal plate (x1) H This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. universal plate (x2) I adapter bracket (x4) J wrench (x1) Package M x 2 M5x14 (x4) M-A M6x14 (x4) M-B M6x30 (x4) M-C M8x30 (x4) M-D M8x50 (x4) M-E washer (x4) small spacer (x8) big spacer (x8) M8x15 (x14) P-A M8x40 (x3) P-B M8x15 (x3) P-C 6mm Allen key (x1) P-D D8 washer (x6) P-E D8 washer (x8) P-F 1 2

3 TCH01 1. Assembling the Base D host machine rack (x1) 5mm Allen key (x1) P-F A C TDV01 Each castor can be adjusted independently for fine tuning. Slightly turn the nut to lower or raise the base. iron shelf (x1) L shelf support (x1) M M5x10 (x3) P-G 5mm Allen key (x1) P-H Insert the casters into the holes of legs and hand thread to secure. Attach the casters with brake to the long legs. Attach the casters without brake to the short legs. NOTE: Lock the brakes on the casters to avoid sudden movements during installation. 2.Attaching the Column to the Base TLP01 B laptop box (x1) N key (x1) P-I 5mm Allen key (x1) P-J TCR01 P-D support rod (x2) O camera shelf (x1) P M5x12 (x4) P- 2mm Allen key (x1) P-L P-B Attach the column to the base using three screws and tighten all screws to secure them. 3 4

4 3. For the model TCH01 installation (Assembly based on the accessories selected by user) Installing the Host Machine Rack 4. For the model TDV01 installation (Assembly based on the accessories selected by user) Installing the Iron Shelf M 4mm Loosen the both washers leaving 4mm space from the iron plate. P-F P-H Insert the host machine rack to the desired position along the column slots, Tighten all screws with an Allen key to secure. buckle Insert the shelf support to the desired position along the front slots of the column. Tighten the two screws to secure it. L P-G Loosen the kn obs to pull one side of the rack to make it keep the maximum space. Put the host machine in the rack and push gently one side of the rack to keep it close to the host machine then tighten the knobs to secure. For security, please buckle up the belt. Attach the iron shelf to the shelf support using three screws,thighten them with a proper screwdriver. 5 6

5 5. For the model TLP01 installation (Assembly based on the accessories selected by user) 6. Installing the Universal Plates Installing the Laptop Box. P-I N Loosen the two knobs on the fixing piece to make it easy to insert the column. F Use the key to open the laptop box. Insert the fixing piece to the desired position along the back slots of the column. Level the fixing piece and tighten both knobs. Insert the laptop box to the desired position along the column slots. Then tigten all screws to secure. P-E P-A X X I P-D P-A P-F P-J +3-3 P-D I H Put the laptop into the box gently then close the box and lock it. Attach the big universal plate to the fixing piece using screws and washers provided. Level the big universal plate then tighten all screws with an Allen key. Then attach the universal plates to the big universal plate using screws and washers(determine the position for the universal plates keeping in mind display sizes).tighten all screws to scecure. 7 8

6 7. For the model TCR01 installation (Assembly based on the accessories selected by user) 8. Installing the Top Cover Installing the Camera Shelf. G O P G Insert the top cover into the both support rods. Remove the two caps from the camera shelf, Attach the camera shelf to the support rods using four screws and tighten all screws to secure it and then reattach the caps to the camera shelf. P-C P- P-L Use three screws to fasten the top cover. 9. Installing the Adapter Brackets Loosen the screws(but don't remove) on the bottom of support rods. J P-C P-L Top of the display Insert the support rods to the desired position (Determine the position for support mount keeping in mind display size.)along the column slots and tighten both screws to secure the support mount. Use three screws to fasten the top cover. 9 10

7 9-1 For Flat Back Screens 10. Hanging the Displays onto the Universal Plates M-A M-B Tighten the bottom bolts to secure the brackets to the universal plates. 9-2 For Recessed Back Screens or to Access A/V Inputs 11. Cable Management M-C M-D M-C M-D or M-C M-D M-E M-E M-E or or Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen. Position the adapter brackets as close as possible to the center of the display. Screw the adapter brackets onto the display. Tighten all screws but do not over tighten

8 Maintenance Check that the bracket is secure and safe to use at regular intervals(at least every three months). Please contact your distributor if you have any questions. E Use the cable clips for routing cables

TV Floor Cart and Accessories

TV Floor Cart and Accessories 11. Adjustment INSTALLATION MANUAL Flo Cart and Accessies Loosen the knobs to adjust the display to the desired angle and tighten the knobs to secure. +5 /-12 + - + - 1200mm 1250mm 1300mm 1350mm 1400mm