SERVICE MANUAL CD RADIO CASSETTE-CORDER. US Model Canadian Model CFD-V15 AEP Model UK Model CFD-V24 E Model. Ver

Transcription

1 CFD-V15/V24 SERVICE MANUAL Ver With SUPPLEMENT 1 ( ) With SUPPLEMENT 2 ( ) US Model Canadian Model CFD-V15 AEP Model UK Model CFD-V24 E Model CFD-V15/V24 Photo : CFD-V15 SPECIFICATIONS AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm, loads, both channels driven from ,000 Hz ; rated 2W per channel-minimum RMS power, with no more than 10% total harmonic distortion in AC operation. (US model) Aerials Other Specification CD player Section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration : Continuous Laser output : Less than 44.6 µw (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) General Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Outputs Number of channels 2 Frequency response 20 20,000 Hz +1 / 2 db Wow and flutter Below measurable limit Model Name Using CD Section NEW Similar Mechanism Tape Section CFD-V10 Optical Pick-up Type KSM-213CDM Tape Transport Mechanism Type MF-V AM : 530 1,710 khz (US, Canadian, Central & South America model) 531 1,602 khz (Singapore, E, Saudi Arabia, AEP, UK, East European, Russian model) ,606.5 khz (Italian model) FM: Telescopic aerial AM : Built-in ferrite bar aerial Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 70 l0,000 Hz Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Headphones jack (stereo minijack) For ohms impedance headphones Power output (excluding US model) 2.3 W W (at 3.2 ohms, 10% harmonic distortion) Continued on page 2 Radio section Frequency range FM : MHz (US, Canadian, Central & South America, E, Singapore model) MHz (AEP, UK, Saudi Arabia, Russian model) MHz (Italian model) MHz (East European model) CD RADIO CASSETTE-CORDER MICROFILM

2 Power requirements For CD radio cassette-corder 120V AC, 60Hz (US, Canadian, Central & South America model) 230V AC, 50Hz (AEP, UK, Italian, East European, Russian, Singapore model) V, V AC selectable 50/60Hz (E, Saudi Arabia model) 9V DC, 6 size D (R20) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder : FM recording Sony R20P : approx h Sony alkaline LR20 : approx. 20 h Tape playback Sony R20P : approx. 7.5 h Sony alkaline LR20 : approx. 15 h CD playback Sony R20P : approx. 2.5 h Sony alkaline LR20 : approx. 7 h Dimensions Approx. 425 x 160 x 246 mm (w/h/d) (16 3 /4 x 6 3 /8 x 9 3 /4 inches) (incl. projecting parts) Mass Approx. 4.0 kg (8 lb. 13 oz) (incl. batteries) Supplied accessories AC power cord (1 ) Design and specifications are subject to change without notice. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. TABLE OF CONTENTS Specifications SERVICING NOTES GENERAL Location and Function of Controls DISASSEMBLY 3-1. Front Cabinet, Contorl Board Removal Power Board, AC Inlet Board, BATT Board, VOL SEL Board Removal Upper Cabinet Removal Optical pick-up Section, Mechanism Deck, Main Board, REC SW Board, CD Motor Board, MONO/ST SW Board Removal DIAL POINTER INSTALLATION ADJUSTMENTS 5-1. Mechanical Adjustments Electrical Adjustments DIAGRAMS 6-1. Explanation of IC Terminals Block Diagrams Printed Wiring Boards Schematic Diagram (Main Section) Schematic Diagram (CD Section) EXPLODED VIEWS 7-1. Front Cabinet Section Upper Cabinet Section Rear Cabinet Section Mechanism Deck Section (1) Mechanism Deck Section (2) Optical pick-up Section ELECTRICAL PARTS LIST MODEL IDENTIFICATION Model Number Label SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK! OR DOTTED LINE WITH MARK! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. MODEL NO. CD RADIO CASSETTE-CORDER CFD-V15 CFD-V24 ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. US, Canadian, Central & South America model : AC120V 60Hz AEP, UK, Italian, East European, Russian, Singapore model : AC230V 50Hz E, Saudi Arabia model : AC V, V selectable. 50/60Hz 2

3 SECTION 1 SERVICING NOTES SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer : Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens. CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. Code number of Chuck Plate Jig : X To Exposed Metal Parts on Set 0.15 µf 1.5kΩ AC voltmeter (0.75V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. LASER DIODE AND FOCUS SEARCH OPERATION CHECK 1. Press CD open knob. 2. Open the lid for CD. 3. Push on SWITCH (S801) as following figure. 4. Confirm the laser diode emission while observing the objecting lens. When there is no emission, Auto Power Control circuit or Optical Pick-up is broken. Objective lens moves up and down once for the focus search. Insert a precision screw driver and push SWITCH (S801) 3

4 SECTION 2 GENERAL LOCATION AND FUNCTION OF CONTROLS MAIN UNIT 1 2! ! 1 Tape operation buttons 2 CD operation buttons button ± button PLAY MODE button DISPLAY/ENTER button fl button p button 3 OPEN / CLOSE button 4 Information display 5 MEGA BASS switch 6 2 Phones jack 7 VOL knob 8 TONE knob 9 OPR / BATT indicator!º FUNCTION switch! TUNE knob! FM MODE switch (AEP, UK, Italian, East European, Russian model) 4

5 r The equipment can be removed using the following procedure. SECTION 3 DISASSEMBLY Set Front cabinet Rear cabinet Control board E, Saudi Arabia model Power board, AC inlet board, BATT board, VOL SEL board Upper cabinet Optical pick-up section Main board, CD motor board Mechanism deck REC SW board MONO/ST SW board AEP, UK, Italian, East European, Russian model Note : Follow the disassembly procedure in the numerical order given FRONT CABINET, CONTROL BOARD REMOVAL 4 Knob, VOL Front cabinet Control board 7 6 Screws +BVTP (2.6X8) Screws +BVTP (3X14) Rear cabinet 3 Screws +BVTP (3X14) 3-2. POWER BOARD, AC INLET BOARD, BATT BOARD, VOL SEL BOARD REMOVAL 3 4 BATT board AC inlet board Power board 2 1 Screws +BVTP (3X10) VOL SEL board 5 Screws +BVTP (3X10) E, Saudi Arabia model Rear cabinet 5

6 3-3. UPPER CABINET REMOVAL 3 Screws +BVTP (3X10) Upper cabinet 2 PUSH OPEN/CLOSE 4 Screws +BVTP (3X10) 2 Handle 1 STOP/EJECT Rear cabinet 3-4. OPTICAL PICK-UP SECTION, MECHANISM DECK, MAIN BOARD, REC SW BOARD, CD MOTOR BOARD, MONO/ST SW BOARD REMOVAL 5 Screws +BVTP (3X10) 8 Remove solder CD motor board Mechanism deck 9 7 Screws +BVTP (3X10) Optical pick-up section REC SW board Wire (Flat type) (16 core) to MAIN board (CNP702) 2 CNP707 (6pin) AEP, UK, Italian, East European, Russian model!º Screw +BVTP (3X8) MONO/ST SW board Main board 4 Rear cabinet 6

7 SECTION 4 DIAL POINTER INSTALLATION Note : Follow the installation procedure in the numerical order given. 1Align the pointer with the groove of front cabinet and insert it as shown in the illustration. 2Align knob (TU) with front cabinet and fasten the screw. Front cabinet 1 Pointer Knob (TU) 2 Screw +BVTP (2.6x8) 3Turn the knob (TU) fully in the direction of the allow as shown in the illustration. 4Turn the tuning capacitor gear fully in the direction of the allow as shown in the illustration. 5Fasten the front cabinet and rear cabinet with the screws. Front cabinet 5 Rear cabinet 4 Tuning capacitor gear 3 Knob (TU) 7

8 SECTION 5 ADJUSTMENTS 5-1. MECHANICAL ADJUSTMENTS PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan 2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase head.) 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Adjustment Value : Speed checker Digital frequency counter 1 to +1% 2,970 3,030Hz Frequency difference between the beginning and the end of the tape should be within 1.5% (45Hz). Adjustment Location : Torque Measurement Torque Torque Meter Meter Reading Forward Forward Back Tension Fast Forward Rewind CQ-102C CQ-102C CQ-201B CQ-201B g cm ( oz inch) g cm ( oz inch) more than 60 g cm (more than 0.84 oz inch) more than 60 g cm (more than 0.84 oz inch) Tape Tension Measurement Torque Meter CQ-403A Meter Reading more than 100g (more than 3.53 oz) TUNER SECTION Tape speed adjustment control inside motor 5-2. ELECTRICAL ADJUSTMENTS TAPE RECORDER SECTION Standard Output Level Output terminal HP OUT load impedance 32 Ω output signal level 0.25V ( 10dB) AM Section Function switch : AM Volume : MIN AM RF signal generator Put the lead-wire antenna close to the set. Test Tape Type Signal Used for WS-48A 3kHz, 0dB Tape Speed Adjustment 0dB = 0.775V Tape Speed Adjustment Procedure : Mode : Playback 30% amplitude modulation by 400Hz signal. Output level : as low as possible FM Section Function switch : FM Volume : MIN FM RF signal generator test tape WS-48A (3kHz, 0dB) set 32Ω speed checker LFM-30 or digital frequency counter 22.5kHz frequency deviation by 400Hz signal. Output level : as low as possible 0.01µF level meter telescopic antenna terminal J301 (phones) set 32Ω J301 (phones) 8

9 Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors. < > : AEP, UK, Singapore, Russian model only << >>: East European model only [ ]: Italian model only (( )) : Saudi Arabia model only AM IF ADJUSTMENT Adjust for a maximum reading on level meter. T2 455kHz VCO Adjustment Procedure : FM RF signal generator Carrier frequency : 98MHz Modulation : No modulation Output level : 1.38mV ( 55dB) 0.01µF telescopic antenna terminal set AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L4 520kHz [516kHz] ((516kHz)) CT4 1,780kHz <1,680kHz> <<1,680kHz>> [1,630kHz] ((1,630kHz)) AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L3 620kHz CT3 1,400kHz FM IF ALIGNMENT Adjust for a maximum reading on level meter. T1 10.7MHz 1. Connect the frequency counter to 4 and 7 pin of IC 1 as shown the figure below. 2. Turn the set to 98MHz. 3. Adjust RV1 for 76kHz±500Hz reading frequency counter. [ MAIN BOARD] (Conductor side) 30 IC µF 33kΩ R6 frequency counter FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L2 86.5MHz <87.0MHz> <<64.0MHz>> [87.35MHz] ((87.35MHz)) CT MHz <108.3MHz> [108.25MHz] ((107.8MHz)) 7 C14 C FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L1 CT1 86.5MHz <87.0MHz> <<68.0MHz>> [87.35MHz] ((87.35MHz)) 109.5MHz <102MHz> [108.25MHz] ((107.8MHz)) Adjustment Location : Main board (See page 10) Adjustment Location : Main board (See page 10) How to put the set into CD Test Mode 1. Set the function switch to power off. 2. Set the function switch to CD while key and p key pressing. The set is into CD test mode (88 is displayed). 3. Turn the power off to release test mode. 9

10 Adjustment Location [MAIN BOARD] (Component side) T1 : FM IF Alignment L3 : AM Tracking Adjustment L4 : AM Frequency Coverage Adjustment RV1 : VCO Adjustment L1 : FM Tracking Adjustment L2 : FM Frequency Coverage Adjustment T2 : AM IF Alignment [MAIN BOARD] (Conductor side) CT4 : AM Frequency Coverage Adjustment CT2 : FM Frequency Coverage Adjustment CT1 : FM Tracking Adjustment CT3 : AM Tracking Adjustment 10

11 SECTION 6 DIAGRAMS 6-1. EXPLANATION OF IC TERMINALS IC702 CD DIGITAL SIGNAL PROCESSOR, LED DRIVE, SYSTEM CONTROL (CXP R) Pin No. Pin name I/O Description 1 SEIN I CD SENS input. 2 CNIN I CD SENS input. 3 DATO O CD DSP command data output. 4 XLTO O Latch output. 5 CLKO O Clock output for CD DSP command. 6 DVSS Digital ground. 7 DVDD Digital power supply (+5V). 8 MON Not used (Open). 9 MDP O Spindle motor drive control. 10 MDS Not used (Open). 11 LOCK O Lock signal output. 12 VPCO2 Not used (Open). 13 VPCO1 Not used (Open). 14 VCKI Not used (Connect to! pin). 15 V16M Not used (Connect to! pin). 16 VCTL Not used ( H level). 17 PCO O Decoder PLL phase comparator output. 18 FILI I Decoder PLL filter input. 19 FILO O Decoder PLL filter output. 20 AVSS Analog ground. 21 CLTV I Decoder PLL VCO control voltage input. 22 AVDD Analog power supply (+5V). 23 RF I CD RF signal input. 24 BIAS I Playback EFM asymmetry current constant input. 25 ASYI I Playback EFM asymmerty comparater voltage input. 26 ASYO O Playback EFM full swing output. 27 TEST1 I Test terminal (Fixed at L ). 28 TEST2 I Test terminal (Fixed at L ). 29 XRST I CD reset input. 30 XRSTO O CD reset output. L : Reset 31 FOK I FOK signal input. 32 LRCK O L/R clock signal output. 33 LRCKI I L/R clock signal input. 34 PCMD O PCM data output. 35 PCMDI I PCM data input. 36 BCK O Bit clock signal output. 37 BCKI I Bit clock signal input. 38 GTOP Not used (Open). 39 XPCK Not used (Open). 40 GFS Not used (Open). 41 RFCK Not used (Open). 42 C2PO Not used (Open). 43 DVSS Digital ground. 44 DVDD Digital power supply (+5V). 45 XROF Not used (Open). 11

12 Pin No. Pin name I/O Description 46 MNT3 Not used (Open). 47 MNT1 Not used (Open). 48 MNT0 Not used (Open). 49 C4M Not used (Open). 50 DOUT Not used (Open). 51 EMPHI Not used (Open). 52 WFCK Not used (Open). 53 SCOR Not used (Open). 54 SBSO Not used (Open). 55 EXCK Not used (Open). 56 DTEST I Test terminal (Fixed at L ). 57 CTEST I Test terminal (Fixed at L ). 58 FR I key input. 59 PLAY/PAUSE I fl key input. 60 FF I ± key input. 61 STOP I p key input. 62 MODE I PLAY MODE key input. 63 DISP/ENTER I DISPLAY/ENTER key input. 64 AU MUTE O Audio mute signal output. 65 BTL MUTE O BTL mute signal output. 66 SENCE2 I CD SENCE input. 67 REC I Function REC input. 68 LIMIT SW I LIMIT switch input. 69 OPEN/CLOSE I CD door open/close switch input. 70 RMC Not used (Fixed at H ). 71 DVSS Digital ground. 72 DVDD Digital power supply (+5V). 73 SEG 15 Not used (Open). 74 SEG 14 Not used (Open) SEG 1 13 O LCD segment output COM 0 3 O LCD common output VCL 1 3 I LCD drive device voltage input. 96 AVSS1 Analog ground. 97 AVDD1 Analog power supply (+5V). 98 AOUT1 O Audio output. 99 AIN1 I Audio input. 100 LOUT1 O L-CH audio output. 101 AVSS1 Analog ground. 102 XVDD Oscillator power supply (+5V). 103 XTAI I Oscillator connect terminal ( MHz). 104 XTAO O Oscillator connect terminal ( MHz). 105 XVSS Oscillator ground. 106 AVSS2 Analog ground. 107 LOUT2 O R-CH audio output. 108 AIN2 I Audio input. 109 AOUT2 O Audio output. 110 AVDD2 Digital power supply (+5V). 111 AVSS2 Ground terminal. 112 NC Not used (Open). 12

13 CFD-V15/V BLOCK DIAGRAM r CIRCUIT BOARDS LOCATION AC INLET board POWER board REC SW board BATT board MONO/ST SW board (AEP, UK, Italian, East European, Russian model) VOL SEL board (E, Saudi Arabia model) CONTROL board MAIN board CD MOTOR board Signal path. F : FM E : PB a : REC J : CD

14

15 CFD-V15/V SCHEMATIC DIAGRAM (MAIN SECTION) r Refer to page 29 for IC Block Diagrams. Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. 2 : nonflammable resistor. : internal component. : e t o N : e t o N The components identi- Les composants identifiés fied by mark! or dotted par une marque! sont criline with mark! are cri- tiques pour la sécurité. tical for safety. Ne les remplacer que par Replace only with part une piéce portant le number specified. numéro spécifié. U : B+ Line. Power voltage is dc 9V and fed with regulated dc power supply from battery terminal. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM (RADIO SECTION) CD STOP (CD SECTION) PLAY (TAPE SECTION) ( ) : AM (RADIO SECTION) REC (TAPE SECTION) Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Signal path. F : FM E : PB a : REC J : CD Abbreviation CND : Canadian SP :Singapore EA : Saudi Arabia IT :Italian EE : East European C&SA : Central and South America CIS : Russian

16 CFD-V15/V24 r WAVEFORMS 6-5. SCHEMATIC DIAGRAM (CD SECTION) r Refer to page 30 for IC Block Diagrams. 1 PLAY MODE ± 0.2 Vp-p 4.8Vp-p 2 IC701 # (RFO) VOLT/DIV : 200mV AC TIME/DIV : 0.5µsec µsec IC702 $ (MNT3) VOLT/DIV : 1V AC TIME/DIV : 50µsec 5Vp-p 4.9Vp-p 3 IC702 #ª (XPCK) 484nsec VOLT/DIV : 1V AC TIME/DIV : 0.1µsec µsec IC702 $ (MNT1) VOLT/DIV : 1V AC TIME/DIV : 50µsec 5Vp-p 2.5Vp-p 237nsec IC702 $ (RFCK) VOLT/DIV : 1V AC TIME/DIV : 50nsec MHz IC702 ` (XTAO) VOLT/DIV : 0.5V AC TIME/DIV : 20nsec Note: All capacitors are in µf unless otherwise noted. pf: µµf 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specified. Note: Note: The components identi- Les composants identifiés fied by mark! or dotted par une marque! sont criline with mark! are cri- tiques pour la sécurité. tical for safety. Ne les remplacer que par Replace only with part une piéce portant le number specified. numéro spécifié. U : B+ Line. Power voltage is dc 9V and fed with regulated dc power supply from battery terminal. Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD STOP ( ) : REC Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD Abbreviation CND : Canadian SP :Singapore EA : Saudi Arabia IT :Italian EE : East European C&SA : Central and South America CIS : Russian

17 r IC BLOCK DIAGRAMS (MAIN SECTION) IC1 CAX1538S IC304 LA4597 IC701 CXA1992BR GND PLL LPF2 VCO PLL LPF 1 PILOT DET LPF 1 PILOT DET LPF 2 ST IND/ VCO CHECK IC301 TA2068N MPX REG VCO MONO/ST SELECT FM DISCRI MUTE MPX REG. AM OSC AFC FM OSC REG OUT /2 COUNTER 1/2 COUNTER MUTING DECORD AMP RCH OUT LCH OUT REG PD 1 PD 2 AUTOBLEND RIPPLE FILTER RIPPLE FILTER AFC/AGC 1 FM RF AM RF IN FM RF IN FM FRONT-END AM FRONT-END BAND PASS MUTE AFC/AGC 2 AM IF / DET TUNING INDICATOR LIN 24 15k MIC I/EX 23 L. RAD 22 10k 6k REC 21 10k 1k L. LO 20 7dB 19 LOGIC 20 R. LO 18 7dB 19 1k 18 FM IF / DISCRI GND TUND IND 10k LINE 17 FE GND 17 FM/AM FE OUT 16 FM IF IN AM IF IN BAND SELECT 1k 10k 6k R. RAD 16 TAPE 15 10k R. LIN 14 MIC IN 13 r IC BLOCK DIAGRAMS (CD SECTION) IC703 BA6898FP DRIVE 1 GND DRIVE F LEVEL SHIFT LEVEL SHIFT DRIVE GND F + BIAS CIRCUIT STANDBY SWITCH DRIVE FIN (FIN) THERMAL SHUT DOWN VREF CH-2 CH-2 T.S.D REG VOLTAGE DOWN, BIAS VOLTAGE DOWN, THERMAL SHUT DOWN MONITOR DRIVER MUTE LEVEL SHIFT LEVEL SHIFT GND (TIN) TIN DRIVE DRIVE T T + DRIVE DRIVE VREF SP I FE_ BIAS F E EI VEE TEO LPF1 TEI ATSC TZC TDFCT VEE BAL1 PD2 IV AMP E IV AMP BAL2 BAL3 BAL4 TOG1 TOG2 TOG3 TOG4 ATSC WINDOW COMP. TZC COMP. PD2 39 F IV AMP PD1 IV AMP TGFL PD1 PDO LD RFTC RF_M RF_O VEE DFCT VEE E-F BALANCE WINDOW COMP. TM1 APC IFB1 IFB2 IFB3 IFB4 IFB5 IFB6 VEE LASER POWER CONTROL TG1 FE AMP TRK. GAIN WINDOW COMP. FO. BIAS WINDOW COMP. RF SUMMING AMP FOH FOL TGH TGL BALH BALL ATSC TZC FZC FOK TRACKING PHASE COMPENSATION RF_I VEE LEVEL S VEE LDON LPCL LPC TGFL MIRR CP DFCTO IFB1-6 BAL1-4 TOG1-4 VEE LINE TAPE TAPE RADOI BUF AMP 10k 10k MONITOR AMP MUTE BUF AMP B1 ON ON MONITOR AMP MUTE BUF AMP B2 10k 10k RADIO TAPE TAPE BUF AMP LINE A1 10k 10k 10k 10k MUTE A2 MIC AMP1 ALC1 ALC2 ON NAB AMP1 26dB REC AMP1 DET REC AMP2 26dB NAB AMP2 10k 1k REF AMP AGC L. PO L. NF L. RO L. IN REF GND R. IN R. RO R. NF R. PO MIC NF CB MIRR IIL TTL IIL DATA REGISTER, INPUT SHIFT REGISTER, ADDRESS DECODER, SENS SELECTOR, OUTPUT DECODER DFCT DFCT1 CC1 CC1 FS1-4 TG1-2 TM1-7 PS1-4 CC2 TM4 FOK TM6 IIL TTL TTL IIL ISET SENS2 SENS1 C. OUT XRST DATA XLT CLK LOCK ISET SL_O SL SL + SL IN RESET REGB REGO MUTE GND (SP IN) SP IN SP SP + GND SPO VC FZC FZC COMP. VEE DFCT FS4 FOCUS PHASE COMPENSATION FS2 FS1 VEE Charge up TG2 TM7 FSET TM3 VEE VEE TM5 TM SL_M SL_P FEO FEI FDFCT FGD FLB FE_O FE_M SRCH TGU TG2 FSET TA_M TA_O

18 NOTE : -XX, -X mean standardized parts, so they may have some difference from the original one. Color indication of Appearance Parts Example : KNOB, BALANCE (WHITE) (RED) Parts color Cabinet's color Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items FRONT CABINET SECTION 2 SP301 LCD SECTION 7 EXPLODED VIEWS The mechanical parts with no reference number in the exploded views are not supplied. Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. Abbreviation CND : Canadian SP : Singapore EA : Saudi Arabia IT : Italian EE : East European CIS : Russian C&SA : Central & South America The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X CABINET (FRONT) SUB ASSY (SP) 1 X CABINET (FRONT) SUB ASSY (EA) 1 X CABINET (FRONT) SUB ASSY (EE) 1 X CABINET (FRONT) SUB ASSY (C&SA) 1 X CABINET (FRONT) SUB ASSY (IT) #1 1 X CABINET (FRONT) SUB ASSY (E) 1 X CABINET (FRONT) SUB ASSY (DARK GRAY) (US) 1 X CABINET (FRONT) SUB ASSY (AEP,UK,CIS) 1 X CABINET (FRONT) SUB ASSY (WHITE) (US) 1 X CABINET (FRONT) SUB ASSY (CND) KNOB (VOL) (DARK GRAY) (EXCEPT SP,EA) KNOB (VOL) (SP,EA) KNOB (VOL) (WHITE) (US) POINTER 9 # #1 12 #1 #6 SP302 8 #6 # KNOB (TU) (DARK GRAY) (EXCEPT SP,EA) KNOB (TU) (SP,EA) KNOB (TU) (WHITE) (US) * CHASSIS (TU) * CONTROL BOARD SCREW (2.6X8), +BVTP STOPPER, WIRING HOLDER (LCD) BUTTON (MEGA BASS) * CHASSIS (DUCT) LCD DISPLAY PANEL, LIQUID CRYSTAL #6 SP SPEAKER (10cm) (L-CH) SP SPEAKER (10cm) (R-CH) EXCEPT WHITE model #6 #11 WHITE model 7-2. UPPER CABINET SECTION EXCEPT WHITE model WHITE model #10 # Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SPRING, CASSETTE UP DAMPER CABINET (UPPER) CABINET (UPPER) (WHITE) (US) SPRING, CD UP PLATE, CHUCKING MAGNET LID, CD LID, CD (WHITE) (US) 58 X HOLDER SUB ASSY, CASSETTE 58 X HOLDER SUB ASSY, CASSETTE (WHITE) (US) BUTTON (REC) BUTTON (REC) (WHITE) (US) BUTTON (PLAY) BUTTON (PLAY) (WHITE) (US) 58 # #10 # BUTTON (REW) BUTTON (REW) (WHITE) (US) BUTTON (FF) BUTTON (FF) (WHITE) (US) BUTTON (STOP) #1 # S EXCEPT WHITE model WHITE model #1 AEP, UK, IT, EE, CIS model BUTTON (STOP) (WHITE) (US) BUTTON (PAUSE) BUTTON (PAUSE) (WHITE) (US) * SHAFT (MD) SPRING, REC SCREW (2.6X8), +BVTP * REC SW BOARD (US,CND, C&SA) * REC SW BOARD (EXCEPT US,CND, C&SA) HANDLE HANDLE (WHITE) (US) COVER, CD RUBBER, VIBRATION PROOF (RED) RUBBER, VIBRATION PROOF (GREEN) WIRE (FLAT TYPE) (16 CORE) CD MOTOR BOARD # CUSHION (CD) CUSHION, RUBBER * MONO/ST SW BOARD (AEP,EE,IT,CIS,UK) S SWITCH, PUSH (1 KEY) (DOOR OPEN/CLOSE) REAR CABINET SECTION 107 F902 T901 # #1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * TERMINAL (ANALOG), ANTENNA * 102 A A MAIN BOARD, COMPLETE (US) * 102 A A MAIN BOARD, COMPLETE (EA) * 102 A A MAIN BOARD, COMPLETE (IT) * 102 A A MAIN BOARD, COMPLETE (CND) * 102 A A MAIN BOARD, COMPLETE (E) * 102 A A MAIN BOARD, COMPLETE (AEP,CIS,UK) * 102 A A MAIN BOARD, COMPLETE (EE) * 102 A A MAIN BOARD, COMPLETE (C&SA) * 102 A A MAIN BOARD, COMPLETE (SP) KNOB (FUN) (DARK GRAY)(EXCEPT SP,EA) KNOB (FUN) (SP,EA) KNOB (FUN) (WHITE) (US) * VOL SEL BOARD (E,EA) GEAR, TUNING CAPACITOR 106 X CABINET (REAR) (CND,C&SA) 106 X CABINET (REAR) (SP) 106 X CABINET (REAR) (EA,E) 106 X CABINET (REAR) (EE) 106 X CABINET (REAR) (DARK GRAY) (US) 106 X CABINET (REAR) (WHITE) (US) 106 X CABINET (REAR) (AEP,IT,UK,CIS) HOLDER, FUSE * POWER BOARD (US,CND, C&SA) #1 not supplied #1 107 F E, EA model #4 104 # ANT1 The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. 112 Ver * POWER BOARD (EXCEPT US,CND, C&SA) * AC INLET BOARD (US,CND, C&SA) * AC INLET BOARD (EXCEPT US,CND, C&SA,E,EA) * AC INLET BOARD (E,EA) SPRING, BATTERY TERMINAL COIL SPRING, BATTERY TERMINAL COIL * BATT BOARD(US,CND, C&SA) * BATT BOARD(EXCEPT US,CND, C&SA) LID, BATTERY CASE(DARK GRAY) LID, BATTERY CASE (WHITE) (US) * PLATE (CD), SHIELD CUSHION (AIR) STOPPER, WIRING ANT ANTENNA, TELESCOPIC!F FUSE, TIME LAG (T0.315AL/250V) (E,EA)!F FUSE, TIME LAG (T2.5AL/250V) (EXCEPT US,CND,C&SA)!F FUSE, GLASS CYLINDERICAL (3.15A/250V) (US,CND,C&SA)!T TRANSFORMER, POWER (AEP,EE,IT,CIS,UK,SP,AR)!T TRANSFORMER, POWER (US)!T TRANSFORMER, POWER (CND,C&SA)!T TRANSFORMER, POWER (E,EA) # Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié

19 7-4. MECHANISM DECK SECTION (1) (MF-V10-117) HRP HE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SPRING (S/P), TORSION SPRING (P), TORSION LEVER (P) ROLLER, PINCH SPRING (F/R), TORSION SPRING (FWD), TORSION GEAR (S REEL) SLIDER (REC) BASE (H), HEAD * SLIDER (REW) * SLIDER (FF) * SLIDER (STOP) * SLIDER (PAUSE) CLAW, REEL * SLIDER (FRP) * SLIDER (EJECT) SPRING (FRP) SPRING (BT) PLATE, LOCK * LEVER (FR) HE HEAD (ERASE) HRP HEAD,MAGNETIC(RECORD/PLAYBACK) 35

20 7-5. MECHANISM DECK SECTION (2) (MF-V10-117) S M # Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LEVER, ERASING PREVENTION SPRING, CASSETTE GEAR (MID) 204 X CLUTCH ASSY GEAR (CAM) * SLIDER (SW) SPRING (GROUND), TORSION LEVER (S.OFF) LEVER (K) 210 X REEL ASSY (N), T BELT 212 X FLYWHEEL ASSY CHASSIS, OUTSERT RING, RETAINING SPRING (CAM), COMPRESSION SPRING, COMPRESSION SPRING (GROUND), COMPRESSION BEARING SPRING (K), COMPRESSION WASHER M601 A A MOTOR ASSY S SWITCH, LEAF (MD POWER) 36

21 7-6. OPTICAL PICK-UP SECTION (KSM-213CDM) not supplied #5 M702 M Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SHAFT, SLED GEAR (B) (RP) The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié GEAR (A) (S)! OPTICAL PICK-UP KSS-213C 255 X CHASSIS ASSY (MB) (RP), MOTOR (INCLUDING M702) (SPINDLE) M701 X GEAR ASSY (MB) (RP), MOTOR (SLED) 37

22 AC INLET BATT CD MOTOR SECTION 8 CONTROL MAIN ELECTRICAL PARTS LIST NOTE : Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms METAL : Metal-film resistor METAL OXIDE :Metal oxide-film resistor F : nonflammable Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : µ, for example : ua... : µ A..., upa... : µ PA... upb... : µ PB..., upc... : µ PC... upd... : µ PD... CAPACITORS uf : µ F COILS uh : µ H Abbreviation CND : Canadian SP : Singapore EA : Saudi Arabia IT : Italian EE : East European CIS : Russian C&SA : Central & South America KR : Korean The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * AC INLET BOARD (US,CND,C&SA) < LIQUID CRYSTAL DISPLAY > * AC INLET BOARD (EXCEPT US,CND,C&SA) * AC INLET BOARD (E,EA) ************** LCD DISPLAY PANEL, LIQUID CRYSTAL < SWITCH > HOLDER, FUSE (E,EA) S SWITCH, PUSH (1 KEY) (MEGA BASS) < CONNECTOR > S SWITCH, KEYBOARD ( ) S SWITCH, KEYBOARD (±) * CNP PIN, CONNECTOR (WITH LOCK) 3P (E,EA) S803 S SWITCH, KEYBOARD (PLAY MODE) SWITCH, KEYBOARD (DISPLAY/ENTER) < FUSE > S SWITCH, KEYBOARD (fl)!f FUSE, TIME LAG (T0.315AL/250V) (E,EA) S SWITCH, KEYBOARD (p) ************************************************************ < JACK > * A A MAIN BOARD, COMPLETE (US)!J INLET, AC ( AC IN) (C&SA) * A A MAIN BOARD, COMPLETE (EA)!J INLET, AC 2P ( AC IN) (EXCEPT US,CND,C&SA) * * A A MAIN BOARD, COMPLETE (IT) A A MAIN BOARD, COMPLETE (CND)!J INLET, AC ( AC IN) (US,CND) * A A MAIN BOARD, COMPLETE (E) < CABLE, HOLDER > * KH HOLDER, CABLE 2P * KH HOLDER, CABLE 2P * KH HOLDER, CABLE 2P ************************************************************ * BATT BOARD (US,CND,C&SA) * BATT BOARD (EXCEPT US,CND,C&SA) *********** ************************************************************ CD MOTOR BOARD ************** CNP < CONNECTOR > PIN, CONNECTOR (SMALL TYPE) 6P < SWITCH > S SWITCH, LEAF (LIMIT) ************************************************************ * CONTROL BOARD ************** HOLDER (LCD) * A A MAIN BOARD, COMPLETE (AEP,CIS,UK) * A A MAIN BOARD, COMPLETE (EE) * A A MAIN BOARD, COMPLETE (C&SA) * A A MAIN BOARD, COMPLETE (SP) ******************** GEAR, TUNING CAPACITOR KNOB (FUN) (EXCEPT KR,EA) KNOB (FUN) (KR,EA) * PLATE (CD), SHIELD < CAPACITOR > C CERAMIC 47PF 5% 50V (US,CND,C&SA) C CERAMIC 0.01uF 20% 16V C ELECT 47uF 20% 10V C CERAMIC 18PF 5% 50V (EXCEPT EE) C CERAMIC 4.7PF 10% 50V (EE) C CERAMIC 27PF 5% 50V (CFD-V15/CFD-V24:IT,KR,EA) C CERAMIC 30PF 5% 50V (AEP,CIS,UK,SP) C CERAMIC 10PF 5% 50V (EE) C CERAMIC 5.6PF 10% 50V (EXCEPT IT,EA) 38

23 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C CERAMIC 6.8PF 10% 50V (IT,EA) C CERAMIC 1.5PF 20% 50V (US,CND,C&SA) C CERAMIC 3.3PF 10% 50V (E,EE,KR,EA) C CERAMIC 2.2PF 10% 50V (AEP,IT,CIS,UK,SP) C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C ELECT 4.7uF 20% 50V C ELECT 1uF 20% 50V C ELECT 47uF 20% 10V C ELECT 47uF 20% 10V C CERAMIC 0.01uF 20% 16V C ELECT 2.2uF 20% 50V C ELECT 100uF 20% 10V C CERAMIC 0.015uF 10% 50V (US,CND,C&SA) C CERAMIC 0.01uF 10% 16V (EXCEPT US,CND,C&SA) C CERAMIC 0.015uF 10% 50V (US,CND,C&SA) C CERAMIC 0.01uF 10% 16V (EXCEPT US,CND,C&SA) C CERAMIC 0.01uF 20% 16V C CERAMIC 18PF 5% 50V C ELECT 1uF 20% 50V C ELECT 0.47uF 20% 50V C ELECT 4.7uF 20% 50V C CERAMIC 0.001uF 10% 50V (US,CND,C&SA) C CERAMIC 0.001uF 10% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.001uF 10% 50V(EE) C CERAMIC uF 20% 16V C ELECT 47uF 20% 10V C CERAMIC 0.039uF 10% 16V C CERAMIC uF 20% 16V C CERAMIC 47PF 5% 50V C ELECT 0.47uF 20% 50V C ELECT 1uF 20% 50V C ELECT 1uF 20% 50V C CERAMIC 0.033uF 10% 50V (EA,SP) C CERAMIC 0.022uF 10% 16V (EXCEPT EA,SP) C CERAMIC uF 20% 16V C CERAMIC 47PF 5% 50V C ELECT 0.47uF 20% 50V C ELECT 1uF 20% 50V C ELECT 1uF 20% 50V C CERAMIC 0.033uF 10% 50V (EA,SP) C CERAMIC 0.022uF 10% 16V (EXCEPT EA,SP) C ELECT 0.47uF 20% 50V C ELECT 47uF 20% 10V C CERAMIC 0.001uF 10% 50V C ELECT 100uF 20% 10V C ELECT 1000uF 20% 10V C FILM 0.1uF 5% 50V C CERAMIC 100PF 10% 50V C CERAMIC 0.039uF 10% 16V C CERAMIC uF 20% 16V C ELECT 100uF 20% 10V C ELECT 100uF 20% 10V C ELECT 10uF 20% 50V C ELECT 100uF 20% 10V C CERAMIC uF 20% 16V C ELECT 47uF 20% 10V C MYLAR 560PF 5% 50V C ELECT 33uF 20% 16V C CERAMIC 0.01uF 20% 16V C ELECT 10uF 20% 50V C ELECT 22uF 20% 50V C CERAMIC 0.01uF 20% 16V C ELECT 4700uF 20% 16V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C ELECT 220uF 20% 25V C ELECT % 10V C ELECT % 25V C CERAMIC 0.01uF 20% 16V C CERAMIC uF 20% 16V C CERAMIC 0.01uF 20% 16V C CERAMIC uF 20% 16V C MYLAR 0.047uF 5% 50V C CERAMIC 0.01uF 20% 16V C ELECT 47uF 20% 10V C CERAMIC 0.022uF 25V C FILM 0.1uF 5% 50V C ELECT 0.47uF 20% 50V C ELECT 47uF 20% 10V C CERAMIC 0.001uF 10% 50V C ELECT 100uF 20% 10V C ELECT 1000uF 20% 10V C FILM 0.1uF 5% 50V C CERAMIC 100PF 10% 50V C CERAMIC 0.039uF 10% 16V C CERAMIC uF 20% 16V C CERAMIC uF 20% 16V C ELECT 47uF 20% 10V C CERAMIC 0.039uF 10% 16V C CERAMIC 0.1uF 50V C CERAMIC uF 20% 16V C CERAMIC 15PF 5% 50V C CERAMIC 0.001uF 10% 50V C FILM 0.1uF 5% 50V C FILM 0.1uF 5% 50V C ELECT 1uF 20% 50V C FILM 0.1uF 5% 50V C MYLAR 0.1uF 5% 50V C TANTALUM 10uF 10% 10V C ELECT 47uF 20% 10V C CERAMIC 0.01uF 20% 16V 39

24 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C MYLAR 0.033uF 5% 50V C MYLAR 0.033uF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V < FILTER > C MYLAR 0.033uF 5% 50V C FILM 0.018uF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 10PF 5% 50V C ELECT 47uF 20% 10V C ELECT 3.3uF 20% 50V C MYLAR 0.068uF 5% 50V C CERAMIC 47PF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 100PF 10% 50V C CERAMIC 100PF 10% 50V C CERAMIC 100PF 10% 50V C CERAMIC 0.001uF 10% 50V C CERAMIC 0.022uF 25V C CERAMIC 100PF 10% 50V C CERAMIC 100PF 10% 50V C CERAMIC uF 20% 16V C CERAMIC 0.01uF 20% 16V C ELECT 47uF 20% 10V C ELECT 470uF 20% 10V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.001uF 10% 50V C CERAMIC 100PF 10% 50V (EXCEPT CFD-V15/CFD-V24 : EA) C MYLAR 0.047uF 5% 50V C ELECT 47uF 20% 10V C ELECT 22uF 20% 50V C ELECT 220uF 20% 6.3V C ELECT 4.7uF 20% 50V C ELECT 4.7uF 20% 50V C CERAMIC 680PF 10% 50V C CERAMIC 680PF 10% 50V C CERAMIC 150PF 10% 50V C CERAMIC 150PF 10% 50V C ELECT 10uF 20% 50V C CERAMIC 0.01uF 20% 16V C ELECT 47uF 20% 10V C CERAMIC 0.01uF 20% 16V C CERAMIC 15PF 5% 50V C CERAMIC 15PF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C FILM 0.47uF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 470PF 10% 50V C CERAMIC 220PF 10% 50V C FILM 0.22uF 5% 50V C CERAMIC 0.01uF 20% 16V C CERAMIC 0.01uF 20% 16V C CERAMIC 100PF 10% 50V C CERAMIC 220PF 10% 50V (C&SA,SP) C CERAMIC 0.01uF 20% 16V CF FILTER, CERAMIC CF FILTER, CERAMIC < CONNECTOR > CNP PIN, CONNECTOR (PC BOARD) 4P CNP PIN, CONNECTOR (PC BOARD) 4P CNP PIN, CONNECTOR (PC BOARD) 4P CNP PIN, CONNECTOR (PC BOARD) 5P CNP CONNECTOR, FFC/FPC 16P * CNP PIN, CONNECTOR (PC BOARD) 13P * CNP PIN, CONNECTOR (PC BOARD) 12P * CNP PIN, CONNECTOR (PC BOARD) 2P * CNP PIN, CONNECTOR (PC BOARD) 2P < TRIMMER > CT CAP, VAR (TUNING) (US,CND,C&SA) CT CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CT CAP, VAR (TUNING) (EE) CT CAP, VAR (TUNING) (US,CND,C&SA) CT CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CT CAP, VAR (TUNING) (EE) CT CAP, VAR (TUNING) (US,CND,C&SA) CT CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CT CAP, VAR (TUNING) (EE) CT CAP, VAR (TUNING) (US,CND,C&SA) CT CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CT CAP, VAR (TUNING) (EE) < VARIABLE CAPACITOR > CV CAP, VAR (TUNING) (US,CND,C&SA) CV CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CV CAP, VAR (TUNING) (EE) CV CAP, VAR (TUNING) (US,CND,C&SA) CV CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CV CAP, VAR (TUNING) (EE) CV CAP, VAR (TUNING) (US,CND,C&SA) CV CAP, VAR (TUNING) (EXCEPT US,CND, C&SA,EE) CV CAP, VAR (TUNING) (EE) CV CAP, VAR (TUNING) (US,CND,C&SA) CV CAP, VAR (TUNING)(EXCEPT US,CND, C&SA,EE) CV CAP, VAR (TUNING) (EE) < DIODE > D DIODE 1SS133T-77 D DIODE 1SS133T-77 D DIODE 1SS133T-77 D DIODE 1SS133T-77 D DIODE 1SS133T-77 40

25 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D DIODE 1SS133T-77 D DIODE 1SS133T-77 (EXCEPT US) D DIODE 1SS133T-77 (EXCEPT US) D DIODE RD5.6ESB3 D DIODE 1SS133T-77 D LED L-34HD (OPR/BATT) D DIODE RD6.8ES-B3 D DIODE 1SS133T-77 (EXCEPT US) D DIODE 1SS133T-77 D DIODE 1SS133T-77 D DIODE 1SS133T-77 Q TRANSISTOR 2SC945-P Q TRANSISTOR KRC110M Q TRANSISTOR 2SC945-P Q TRANSISTOR 2SC945-P Q TRANSISTOR 2SC1815-GR Q TRANSISTOR KRC111M-AT Q TRANSISTOR 2SA1175-HFE Q TRANSISTOR KRC101M-AT Q TRANSISTOR 2SD2396K Q TRANSISTOR KTC3203Y-AT Q TRANSISTOR KTA1271-Y-AT < FERRITE BEAD > FB FERRITE BEAD INDUCTOR FB FERRITE BEAD INDUCTOR FB FERRITE BEAD INDUCTOR FB FERRITE BEAD INDUCTOR FB FERRITE BEAD INDUCTOR < FILTER > FL FILTER, BAND PASS (E,AEP,IT,CIS,UK,EA,SP) FL FILTER, BAND PASS (EE) < IC > IC IC CXA1538S IC IC TA2068N IC IC LA4597 IC IC CXA1992BR IC IC CXP R IC IC BA6898FP < JACK > J JACK (2) < CABLE, HOLDER > * KH HOLDER, CABLE 2P (AEP,IT,CIS,UK,EE) * KH HOLDER, CABLE 2P < COIL > L COIL, AIR-CORE (US,CND,C&SA) L COIL, AIR-CORE (AEP,IT,CIS,UK,SP,EA,E) L COIL, AIR-CORE (EE) L COIL, AIR-CORE (CFD-V15) L COIL, AIR-CORE (AEP,CIS,UK,SP) L COIL (WITH CORE) (EE) L COIL (WITH CORE) (IT,EA) L ANTENNA, FERRITE-ROD (MW) (US,CND,C&SA) L ANTENNA, FERRITE-ROD (MW) (EXCEPT US,CND,C&SA) L COIL (OSC) L INDUCTOR 1uH L INDUCTOR 10uH (US,CND,C&SA,E,EA) < TRANSISTOR > Q TRANSISTOR KRC101M-AT Q TRANSISTOR KRC110M Q TRANSISTOR 2SC945-P < RESISTOR > R CARBON 220 5% 1/4W (US,CND,C&SA,EE) R CARBON 2.2K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 3.3K 5% 1/4W (US,CND,C&SA) R CERAMIC 2.2PF 10% 50V (IT) R CERAMIC 4.7PF 10% 50V (EA) R CARBON 330 5% 1/4W (EXCEPT US,CND,C&SA,EE) R CARBON 470 5% 1/4W (US,CND,C&SA) R CARBON 560 5% 1/4W (EE) R CARBON 68 5% 1/4W R CARBON 6.8K 5% 1/4W R CARBON 6.8K 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W (AEP,EE,IT,CIS,UK,SP) R CARBON 15K 5% 1/4W R CARBON 82 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 33K 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 5.6K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 470K 5% 1/4W R CARBON 470 5% 1/4W (EA,SP) R CARBON 1K 5% 1/4W (C&SA,E) R CARBON 2.2K 5% 1/4W (EXCEPT C&SA,E,EA,SP) R CARBON 100K 5% 1/4W R CARBON 1.5K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W 41

26 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R CARBON 15K 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 82 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 33K 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 5.6K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 470K 5% 1/4W R CARBON 470 5% 1/4W (EA,SP) R CARBON 1K 5% 1/4W (C&SA,E) R CARBON 2.2K 5% 1/4W (EXCEPT C&SA,E,EA,SP) R CARBON 100K 5% 1/4W R CARBON 1.5K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 100 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 1M 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 1M 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 130 5% 1/4W R CARBON 6.8K 5% 1/4W R CARBON 10 5% 1/4W R CARBON 4.7K 5% 1/4W R CARBON 22K 5% 1/4W R CARBON 3.3K 5% 1/4W!R CARBON 1 5% 1/4W F (US) R CARBON 47K 5% 1/4W R CARBON 1.5K 5% 1/4W R CARBON 680 5% 1/4W R CARBON 220 5% 1/4W R CARBON 220 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 2.2K 5% 1/4W R CARBON 560 5% 1/4W R CARBON 220K 5% 1/4W R CARBON 150K 5% 1/4W R CARBON 180K 5% 1/4W R CARBON 150K 5% 1/4W R CARBON 330K 5% 1/4W R CARBON 8.2K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1M 5% 1/4W R CARBON 680K 5% 1/4W R CARBON 10 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 20K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 510K 5% 1/4W R CARBON 68K 5% 1/4W R CARBON 150K 5% 1/4W R CARBON 75K 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 100K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 33K 5% 1/4W R CARBON 22K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 6.8K 5% 1/4W R CARBON 22K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 33K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 12K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 15K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 100 5% 1/4W R CARBON 220 5% 1/4W R CARBON 47K 5% 1/4W R CARBON 3.3K 5% 1/4W R CARBON 1K 5% 1/4W R CARBON 10K 5% 1/4W R CARBON 1M 5% 1/4W R CARBON 220K 5% 1/4W R CARBON 10K 5% 1/4W < VARIABLE RESISTOR > R CARBON 10 5% 1/4W R CARBON 82K 5% 1/4W R CARBON 68K 5% 1/4W R CARBON 68K 5% 1/4W R CARBON 68K 5% 1/4W RV RES, ADJ, METAL 22K (VCO) RV RES, VAR, CARBON 20K/20K (TONE) RV RES, VAR, CARBON 20K/20K (VOLUME) < SWITCH > R CARBON 68K 5% 1/4W R CARBON 82K 5% 1/4W 42 S SWITCH, LEVER SLIDE (FUNCTION) The components identified by mark! or dotted line with mark! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.