Description IN(-) IN(+) FAN156L6X CN -40 to 85 C 6-Lead, MicroPak, 1 x 1.45 mm Wide

Transcription

1 FAN56 Low Voltage Comparator Features Low Supply Current: I DD 6 μa (Typical) Single Pow er Supply Operation Wide Common-Mode Input Voltage Range Push-Pull Output Circuit Low Input Bias Current Internal Hysteresis Packaged in MicroPak 6 Applications Description The FAN56 is a low -pow er single comparator that typically consumes less than µa of supply current. It is guaranteed to operate at a low voltage of.6 V and is fully operational up to 5.5 V, making it convenient for use in.8,. V, and 5. V systems. The FAN56 has a complementary push-pull P- and N- channel output stage capable of driving a rail-to-rail output sw ing w ith a load ranging up to 5. ma. V DD Mobile Phones Alarm and Security Systems Personal Digital Assistants IN(-) IN(+) - + Out V SS Figure. Functional Diagram Ordering Information Part Number Top Mark Operating Temperature Range Package FAN56L6X CN - to 85 C 6-Lead, MicroPak, x.5 mm Wide Packing Method 5 Units on Tape and Reel Semiconductor Components Industries, LLC. Publication Order Number: November-7, Rev. FAN56/D

2 Pin Configuration Pin Definitions OUT 6 V DD VSS 5 NC IN+ IN- Figure. Pin Configuration (Top-Through View) Pin # Name Description OUT Comparator Output VSS Negative Supply Voltage IN+ Non-Inverting Input IN- Inverting Input 5 NC No Connect 6 V DD Positive Supply Voltage Function Table Inputs IN(-) > IN(+) IN(+) > IN(-) Outputs Output LOW Output HIGH V DD V OUT V IN(-) V OUT V DD V OUT V OUT V IN (+) V IN (-) V IN(+) Figure. V IN vs. V OUT

3 Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Condition Min. Max. Unit VDD to VSS Supply Voltage V 6. DV IN Differential Input Voltage ±6 V IN Input Voltage V SS to V DD V ts Output Short Circuit Duration () Indefinite s TJ Junction Temperature +5 C TSTG Storage Temperature Range C P D Pow er Dissipation 9 mw Θ JA Thermal Resistance 5 C/W ESD IEC 6-- System ESD JEDEC JESD-A, Human Body Model JEDEC JESD-C, Charged Device Model Air Gap 5 Contact 8 All Pins 8 Pin to Pin: IN(-), IN(+) to VDD or VSS Note:. The maximum total pow er dissipation must not be exceeded. All Pins kv Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. ON Semiconductor does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Condition Min. Max. Unit V DD to V SS Pow er Supply V 5.5 V DD Pow er Supply V SS V V VIN Input Voltage VSS to VDD V V DD 5. V 5 IOH/IOL Output Sink/Source Current VDD. V VDD.6 V T A Operating Temperature, Free Air C ma

4 Electrical Characteristics Symbol Parameter Condition Min. Typ. Max. Unit VDD=5.5V, VSS=GND, and TA=+5 C VHYS Input Hysteresis VCM=.5 VDD mv V IO Input Offset Voltage () V CM=.5 V DD -5 ± +5 mv I IO Input Offset Current pa II Input Bias Current pa VCM Common Mode Input Voltage VSS VDD V CMRR Common Mode Rejection Ratio () VCM=VDD 68 db I DD Supply Current 6 7 µa PSRR Pow er Supply Rejection Ratio () ΔVDD=.5 V 5 8 db IOS Output Short Circuit Current V O=V DD 6 V O=V SS 9 V OL Low -Level Output Voltage I SINK=5. ma.. V V OH High-Level Output Voltage I SOURCE=5. ma V t PLH t PHL Propagation Delay (Turn-On) Propagation Delay (Turn-Off) Overdrive mv, CL=5 pf Overdrive= mv, C L=5 pf t TLH Response Time, Output Rise/Fall ( ). C L=5 pf t THL 5. VDD=V, VSS=GND, and TA=+5 C ma. µs. µs V HYS Input Hysteresis V CM=.5 V DD mv V IO Input Offset Voltage () V CM=.5 V DD -5 ± +5 mv I IO Input Offset Current pa I I Input Bias Current pa V CM Common Mode Input Voltage V SS V DD V CMRR Common Mode Rejection Ratio () V CM=V DD 6 db IDD Supply Current µa PSRR Pow er Supply Rejection Ratio () ΔV DD=.5 V 5 8 db I OS Output Short Circuit Current V O=V DD 7 VO=VSS 5 VOL Low -Level Output Voltage ISINK=. ma.5.5 V V OH High-Level Output Voltage I SOURCE=. ma V ns ma tplh Propagation Delay (Turn-On) Overdrive= mv, CL=5 pf.5 µs t PHL ttlh Propagation Delay (Turn-Off) Response Time, Output Rise/Fall () Overdrive= mv, CL=5 pf C L=5pF tthl 6..7 µs 6. ns Continued on the following page

5 Electrical Characteristics (Continued) Symbol Parameter Condition Min. Typ. Max. Unit VDD.6V, VSS GND, and TA=+5 C VHYS Input Hysteresis VCM=.5 VDD.5 mv V IO Input Offset Voltage () V CM=.5 V DD -5 ± +5 mv I IO Input Offset Current pa II Input Bias Current pa VCM Common Mode Input Voltage VSS VDD V CMRR Common Mode Rejection Ratio () VCM=VDD 56 db I DD Supply Current 5 5 µa PSRR Pow er Supply Rejection Ratio () ΔVDD=.5 V 5 8 db IOS V O=V DD 5.5 Output Short Circuit Current ma V O=V SS 7.5 V OL Low -Level Output Voltage I SINK=. ma..5 V V OH High-Level Output Voltage I SOURCE=. ma.5.5 V t PLH Propagation Delay (Turn-On) Overdrive= Mv, C L=5pF.5 µs t PHL Propagation Delay (Turn-Off) Overdrive= Mv, C L=5 pf t TLH Response Time, Output Rise/Fall () 6.5 C L=5 pf t THL..5 µs Notes:. Differential input sw itching level is guaranteed at the minimum or maximum offset voltage, minus or plus half the maximum hysteresis voltage.. Guaranteed by design and characterization data.. Input signal: khz, square-w ave signal w ith ns edge rate. ns 5

6 Typical Performance Characteristics IDD, Sopply Current (µa) VDD=.6V VDD=.V VDD=5.5V -55 ⁰C - ⁰C -5 ⁰C 5 ⁰C 85 ⁰C 95 ⁰C T A, Ambient Temperature VDD 6. VDD VDD.. Temp. =5C C L = 5pF Frequency (Khz) Figure. Supply Current vs. Temperature Figure 5. Supply Current vs. Output Transition Frequency ICC (µa) IDD, Supply Current (µa) ⁰C 5 ⁰C 85 ⁰C V DD, Supply Voltage (V) Figure 6. Supply Current vs. Supply Voltage Figure 7. Output HIGH vs. Output Drive Current V OH, Output Voltage HIGH State (V) VDD=.6V VDD=.V VDD=5.5V 6 8 I SOURCE, Output Source Current (ma) VOL, Output Voltage Low (mv) VDD=.6V VDD=.V VDD=5.5V... I SINK, Output Sink Current (ma) tphl (ns) VDD 6.VDD 5.5VDD Temperature Figure 8. Output LOW vs. Output Drive Current Figure 9. Propagation Delay (t PHL) vs. Temperature 6

7 Typical Performance Characteristics (Continued) tplh (ns) VDD.VDD 5.5VDD Temperature tplh tphl V DD =.V Temp. =5 C Overdrive (mv) Delay (ns) Figure. Propagation Delay (t PLH) vs. Temperature Figure. Propagation Delay vs. Input Overdrive Input Common-Mode Voltage Range (V) T A = 5 C 5 6 Voltage (V) VDD Output Input Overdrive = 5mV Time (µs) V S, Supply Voltage (V) Figure. Input Common-Mode Voltage Range vs. Supply Voltage Figure. Pow er-up Delay 7

8 Physical Dimensions X.5 C.5 (.5) TOP VIEW PIN IDENTIFIER 5.55MAX.5 C C DETAIL A. B X.5 C..5. A.5 C (.9) 5X (.5) X PIN.5.5 6X. C B A.5 C () (.) 6X RECOMMENED LAND PATTERN.. 6X.. (.75) X Notes: (.5) 6X.5 BOTTOM VIEW...75 X 5 CHAMFER. CONFORMS TO JEDEC STANDARD M-5 VARIATION UAAD. DIMENSIONS ARE IN MILLIMETERS. DRAWING CONFORMS TO ASME Y.5M-99. FILENAME AND REVISION: MAC6AREV 5. PIN ONE IDENTIFIER IS X LENGTH OF ANY OTHER LINE IN THE MARK CODE LAYOUT. Figure. 6-Lead, MicroPak, x.5 mm Wide 5X (.) X DETAIL A PIN TERMINAL Package drawings are provided as a service to customers considering ON Semiconductor components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact an ON Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of ON Semiconductor s worldwide terms and conditions, specifically the warranty therein, which covers ON Semiconductor products. Package Designator Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 5 (Typical) Empty Sealed L6X Carrier 5 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed 8

9 ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor s product/patent coverage may be accessed at /site/pdf/patent-marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. Typical parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 95 E. nd Pkwy, Aurora, Colorado 8 USA Phone: or Toll Free USA/Canada Fax : or Toll Free USA/Canada orderlit@onsemi.com N. Amer ican Technical Support: Toll Free USA/Canada. Eur ope, Middle East and Afr ica Technical Support: Phone: 79 9 Japan Customer Focus Center Phone: ON Semiconductor Website: Or der Literature: For additional information, please contact your local Sales Representative 9