Slicer"CURA" User Instructions for Olivetti S2 3D Printer

Transcription

1 Slicer"CURA" User Instructions for Olivetti S2 3D Printer 1

2 Cura Install - 1 Click Next 2

3 Cura Install - 2 Check all components. Then click Install 3

4 Cura Install - 3 Click Next 4

5 Cura Install - 4 The Wizard installs the Arduino drivers, to enable the PC to recognize the printer. Then click Finish 5

6 Cura Install - 5 At the end of Setup, click Finish, keeping the flag on Start Cura, as shown in the figure. 6

7 Printer Setup- 1 The Configuration Wizard starts automatically. Click Next 7

8 Printer Setup - 2 Select Other. Then click Next 8

9 Printer Setup - 3 Select Custom. Then click Next 9

10 Printer Setup - 4 Enter the Olivetti S2 data as shown in the Figure: Width: 455 Depth: 400 Height: 400 Nozzle size: 0,5 Flag Heated Bed Click Finish to end the Printer Setup 10

11 Software Setup - 1 In the first screen you can see a small robot on the printing bed. Right-click to delete this or any other object 11

12 Software Setup - 2 The black triangle at the lower left corresponds to the zero point of the 3D printer. At the printing start, the axes will move to the zero point. 12

13 Software Setup - 3 The Cura default setting is for single extruder printers. To set also the S2 second extruder, click on the menu "Machine" and select "Machine Settings" 13

14 Software Setup - 3 In the Machine settings window, modify the Extruder count item from 1 to 2. Click OK 14

15 Software Setup - 4 Select again Machine Settings. Now appear the offsets of the second extruder. Modify the Offset Y from 21.6 to 0.0 (the offsets are set in the S2 firmware) 15

16 Choose and prepare the object - 1 Click on Load to select the object file and place it on the printing bed. The compatible file formats are: STL OBJ AMF 16

17 Choose and prepare the object - 2 Once imported the object, you need to position it and set the printing parameters. The object is placed by default in the middle of the printing bed. 17

18 Choose and prepare the object - 3 Right-click to center, delete, multiply.. the object. 18

19 Choose and prepare the object - 4 Clicking on the object, three icons appear at the bottom left. The icon 'Rotate' enables to rotate the object on the printing bed by using the mouse. The rotation is of 15 Hold down the shift key to rotate of 1 19

20 Choose and prepare the object - 5 The Lay Flat option allows to change the object position and choose the side of the object that stands on the printing bed. 20

21 Choose and prepare the object - 6 The Reset option allows to reset changes and start over. 21

22 Choose and prepare the object - 7 The Scale icon allows to modify the object size. Scaling can be uniform or single axis. WARNING: excessively increasing the scale can lower the resolution and deteriorate print quality. 22

23 Choose and prepare the object - 8 The To Max option allows to increase the object size up to the maximum print size. 23

24 Choose and prepare the object - 9 The Reset option allows to reset changes and start over. 24

25 Choose and prepare the object - 10 The Mirror option allows to mirror the object in different positions. 25

26 View Mode - 1 Click on View Mode icon to open the related Menu. Select "Layers" to access the mode that allows you to view the object growth and to set all the printing parameters 26

27 View Mode - 2 It s advisable to work on Layers mode to enter the printing parameters, as they are displayed in an optimal way. Use the shift key and the arrow keys on the numeric string to see each layer and therefore the progressive growth of the object. 27

28 Print Setup - Basic/Quality section - 1 Layer height corresponds to the height of the layers that make up the object. Thinner layers enable higher resolution, but require a longer printing time. 28

29 Print Setup - Basic/Quality section - 2 Shell thickness This parameter sets the object perimeter thickness. The shell setting is a function of the nozzle diameter. With a 0,5 mm nozzle diameter: 1 perimeter 0,5 2 perimeters 1,0 3 perimeters 1,5 So the entered data must be a multiple of the nozzle diameter. The outer perimeter is shown in red; the internal perimeters in green. 29

30 Print Setup - Basic/Quality section - 3 Enable retraction It enables the material retraction. This parameter must be flagged because it allows the control of material retraction during the printing. 30

31 Print Setup - Basic/Fill section - 1 Bottom/Top thickness This parameter is related to bottom and top faces of the object. This parameter has to be set as a function of the layer thickness. With layer at 0.2 mm: 1 lower and upper layer: lower and upper layers: lower and upper layers: 0.6 Then the entered data must be a multiple of the layer thickness. 31

32 Print Setup - Basic/Fill section - 2 Fill density It corresponds to the fill percentage of the internal parts of the object. With the increase of filling percentage, the consistency of the object enhances. hollow object: fill density 0% partially filled object: Fill density 1%/99% Totally filled object: Fill density 100% 32

33 Print Setup - Basic/Speed and Temperature section Print Speed Basic print speed (mm/sec) to be set for printing. Printing Temperature Nozzle(s) temperature, to be set according to the material characteristics. Bed Temperature Printing bed temperature, to be set according to the material characteristics. 33

34 Print Setup - Basic/Support section - 1 Support Type When the object needs a support because the shape has some significant overhang, you can select two options: OPTION 1 Touching Buildplate The software creates the support only where it is in contact with the printing bed 34

35 Print Setup - Basic/Support section - 2 OPTION 2: Everywhere: It creates the support wherever there is any overhang 35

36 Print Setup - Basic/Support section - 3 At the line Structure type you can set whether the support should be linear (Lines) or grid (Grid). It is advisable to choose Lines, to facilitate the support material removal. 36

37 Print Setup - Basic/Support section - 4 At the line Overhang angle for support, you can set the overhang angle from which the support will be generated. It s advisable to keep this value at 60 37

38 Print Setup - Basic/Support section - 5 Support dual extrusion Since the S2 is equipped with dual-extruder, you can choose the extruder which will create the support. Choosing Second Extruder, the software will indicate how much material will be used with two extruders. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 38

39 Print Setup - Basic/Support section - 6 Platform Adesion Type Two options: BRIM OPTION This option allows to create a further basis (as shown in the figure), which will ensure better adhesion to the printing table. Opening the next dropdown you can define the width of the Brim ( Brim line amount ). 39

40 Print Setup - Basic/Support section - 7 RAFT OPTION This function creates a basis of some layers under the object, which improve the adhesion to the printing bed. This feature is especially used for objects with very small bases. The config list allows to set the Raft, managing the specific parameters. 40

41 Print Setup - Basic/Dual extrusion section - 1 Using two extruders, it is possible to choice between 2 functions to prevent material dripping during the resting phase of one extruder. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. Wipe&Prime tower option This option creates a tower next to the object. Every time that one extruder has to start printing again, it will create a small square on the tower, to avoid dripping. 41

42 Print Setup - Basic/Dual extrusion section - 2 Ooze shield option This option allows to create a protective shell around the object, that will avoid the material drops from interfering with the printed object. This option is often complex to manage, especially when the objects has complicated geometries. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 42

43 Print Setup - Basic/Filament section Diameter It indicates the filament diameter. The Olivetti S2 works only with 1,75 mm filaments. Flow It s the material flow to be set for printing. For not-experted users, it is advisable to keep the default value of 100% 43

44 Print Setup - Advanced/Machine section Select the ADVANCED Menu Nozzle Size (nozzle hole diameter): enter the millimeter value of the mounted nozzle diameter. On Olivetti S2 it is mounted by default a nozzle of 0.5 mm. 44

45 Print Setup - Advanced/Retraction section Retraction If the Retraction feature was flagged in the Basic section (see the slide n. 30), now it s possible to set the retraction Speed and Distance (ie quantity of retracted material). 45

46 Print Setup - Advanced/Quality section - 1 Initial Layer Thickness It means the first layer height. It s advisable to keep the value at 0,2 mm. Initial layer line width This item indicates the line width for first layer. It s advisable to keep the value at 100% 46

47 Print Setup - Advanced/Quality section - 2 Cut Off object It allows to cut the object, starting from the printing bed. This feature is useful especially to check the print quality of the top section of the object. Cutting off the object, printing starts directly at the height set. 47

48 Print Setup - Advanced/Quality section - 3 Dual extrusion overlap Using both extruders, this feature adds a material overlay, improving adhesion quality between two materials. The following slides show how to use this feature N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 48

49 Print Setup - Advanced/Quality section - 4 Dual extrusion overlap The object was divided into 2 parts, sectioning at the material change. Right click, select "Dual Extrusion Merge". The two parts merge (see next slide) N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 49

50 Print Setup - Advanced/Quality section - 5 Dual extrusion overlap The figure shows the object combined with different colors, which indicate the part of each extruders. This way, it is possible to create a two-colour and/or twomaterial object. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 50

51 Print Setup - Advanced/Speed section - 1 This section allows to set the different printing speed (in mm/sec) for each activity. Travel Speed It means speed of the extruder during the nonprinting movements (travels). These movements are highlighted in blue. 51

52 Print Setup - Advanced/Speed section - 2 Bottom Layer Speed Printing speed for the first full layer Infill Speed Printing speed for intermediate layers Top/Bottom Speed Printing speed for bottom and top full layers. 52

53 Print Setup - Advanced/Speed section - 3 Outer Shell Speed Printing speed for outer shell (highlighted in red) Inner Shell Speed Printing speed for inner shell (highlighted in green) 53

54 Print Setup Advanced/Cool section Cool Minimal layer time It means the minimum time at which you want to print the single layer. This feature is useful especially for very small pieces/very small parts, when the material cooling can be critical. Enable cooling fan This item must be flagged 54

55 Plugins section It s advisable to NOT use these plugins 55

56 Start/End G-Code Section - 1 Start/End G- Code These are strings of machine-code to implement specific printing features. Some specific strings was created/modified for S2, especially for double extruder printing. Next slides show the specific items where changes have been made 56

57 Start/End G-Code Section - 2 End g.code Modified string. The inserted value is G28 X0 Y400 57

58 Start/End G-Code Section - 3 Preswitch Extruder Modified String. Printing with two extruders, it allows to set the temperature of the pausing extruder. The temperature is set 30 C lower than the printing temperature. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 58

59 Start/End G-Code Section - 4 Postswitch Extruder Modifies string. It allows to set at the right printing temperature the extruder which is going to resume printing. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 59

60 Start/End G-Code Section - 5 Start2 gcode Modified String. At the printing beginning, it manages the second extruder temperature. N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 60

61 Start/End G-Code Section - 6 End2 Modified string At the printing end, it moves the extruder in a position ideal to facilitate the object removal. G28 X0 Y400 61

62 EXPERT section - 1 From the Expert Menu, select Open expert setting 62

63 EXPERT/Dual Extrusion section Wipe&prime Printing with two extruders, it allows to set the volume of the Wipe&Prime tower (see slide 41) N.B.: to print with both the extruders, it is recommended to set the slicing with "Simplify3D" software instead of Cura. 63

64 EXPERT/Retraction section - 1 Minimum travel Minimum nonprinting extruder movement (travel) for which a retraction is activated. Minimal extrusion before retracting Minimum estrusion which has to be made before a subsequent retraction. 64

65 EXPERT/Retraction section - 2 Z hop when retracting It corresponds to the downward and upward axis Z movement (printing bed), when the printer makes a retraction. This feature is useful especially to avoid friction between nozzle and bed, when the extruder makes a long travel (nonprinting movement) 65

66 Sezione EXPERT/Skirt At the printing beginning, the skirt feature allows to create outer perimeters, to improve the initial printing quality Line count It sets how many lines make the skirt. Start distance It sets the distance between the skirt and the object Minimal length Skirt minimal length 66

67 EXPERT/Cool section On the S2 this section can t be used, because the cooling fan are controlled via hardware (button). 67

68 EXPERT/Infill section - 1 Infill Solid infill Top Solid infill Bottom Flagging these items, the Top and bottom faces of the object will be filled; unflagging them, the faces will be empty. 68

69 EXPERT/Infill section - 2 Infill overlap Overlappping percentage between perimeters and filled layers of the object. Infill print after perimeters It allows to create the filled layers before/after the perimeters. 69

70 EXPERT/Support and Black Magic section Support Features already described at slides 34 and following Black Magic option available only for objects not filled (only perimeters), as the Z axis constantly moves down and not layer after layer. 70

71 EXPERT/Brim, Raft and Foxx Horrible sections Brim and Raft Features already described at slides and following Fix Horrible Features not available for the Olivetti S2 71

72 File saving - 1 Once the printing setup is complete, the file has to be saved, selecting File Save Gcode, to save the file on your PC or directly on the SD Card. The file extension is Tollpath (Gcode) 72

73 File saving - 2 Once the Gcode was saved, it s advisable to save also the printing profile, selecting File Save Profile. This way, it s possible to save the printing setup used for each object and/or object groups. 73

74 Slicer"CURA" User Instructions for Olivetti S2 3D Printer 74