Front View Side View Top View

Size: px
Start display at page:

Download "Front View Side View Top View"

Transcription

1 Instructions: Below is a detailed instructional guide to producing a functioning Brace assembly from the provided CAD files. Sizing guide Measurements for brace sizing are best taken using a flexible measuring tape. Ideal dimensions will vary between individuals, and care should be taken to ensure the accuracy of recorded measurements. The current brace revision is designed as a generic and symmetrical assembly that is capable of being worn on either leg. Advanced CAD modeling skills in conjunction with in-depth knowledge of the anatomy of the lower leg could lead to a very precise end product. As the model stands now, the sizing instructions for the critical dimensions are outlined below Model Manipulation The dimensions discussed below must be obtained prior to CAD file manipulation to ensure a proper fit to each individual. The current model was constructed using Solidworks as the CAD software. All size adjustments can be conducted within the top level assembly file Front View Side View Top View The vertical distance between the center of the upper and lower cross supports and the center of the hinges (dimension 1, seen in the front view) can be adjusted by manipulating the distance2 mate for the upper and distance5 mate for the lower in the assembly mate group. To adjust, right click on the mate, click on edit feature, and input the desired dimension in the distance box.

2 The horizontal spacing between the inside wall of the two hinges (dimension 2, seen in the front view) can be adjusted by manipulating the distance1 mate in a similar fashion as outlined above. The offset distance of the upper and lower cross support from the center of the hinge (dimension 3, seen in the side view) can be adjusted by manipulating the distance4 mate for the upper and distance6 mate for the lower in a similar fashion as outlined above. The Radius and wrap angles of the upper and lower cross support (dimensions 4 & 5, seen in the top view) can be manipulated by editing the individual part files of each component. To edit a part file while inside of the assembly file, double click on the component of interest to display all internal feature dimensions than can be edited. After editing, initiate a rebuild (CTRL + Q) to implement the changes into the assembly. Part files will automatically be updated but will require a save for the changes to permanently take effect. It should be noted that as currently designed, the size of the upper and lower connectors are derived based on the position of other components in the assembly. Manipulating any of the above dimensions should automatically update the size and shape of the four connectors after performing a rebuild. Also of note, the two hinge assemblies are designed to be printed as a pre-assembled component on a printer with dissolvable support material. If such resources are not available, the hinges will likely need to be redesigned as two separate components (inner component and outer component). File Creation Upon updating the CAD files to satisfactory sizes, the assembly must be saved in a format that can be interpreted by the 3D printer being used to produce the parts. Different printers require different file formats, but for this guide the.stl file type will be highlighted. STL files are widely used and are accepted on many of the printers in production today. If the printer being used requires a file type other than an STL, consult the instructional guide for that specific printer model to obtain information about the necessary file type. To save a file as an STL, select Save As from the File tab, and select STL from the drop down file type box. Click on the options button to edit specifics of the STL like resolution and unit type. Of special note, the save all components of an assembly as a single file box should be checked when saving STL s for the left and right hinge if dissolvable support material is being utilized. Otherwise, the box should be unchecked to produce STL s of the individual components. An STL file is required for each individual component of the Brace assembly. The process is demonstrated by the following figure:

3

4 Printer setup After STL files have been produced, they can be imported into the 3D printer interface software. The Makerbot Replicator 2X was used to print several prototype pieces for this project, and will be the focus of this section. The Replicator 2X uses the Makerbot Desktop as its user interface software, which will be briefly outlined below. To begin the printing process, import the appropriate STL files by clicking Add File. The size and orientation of the STL can be manipulated using the buttons on the left-hand side of the screen. The print settings can be manipulated by opening the settings menu, located next to the import button. The status of the printer can be displayed by clicking on the monitor button at the bottom left of the desktop. After all settings are adjusted, click on the Print button to begin printing. The process is demonstrated by the following figures.

5 Trial and error is often necessary to obtain the optimal printer settings for different print jobs. The prototype pieces for this project were printed at an extruder temperature of 240 C, standard extrusion speeds, and with a diamond infill pattern. Post Print Treatment The only post print treatment involved with this project is the removal of excess material. If the piece was printed on a raft, it should be removed along with any breakaway support. If dissolvable filament was used for the support material, it should be allowed to soak for several hours. A small amount of force may be required to help break loose and dissolve the support material inside of the hinges. Brace Assembly Prior to assembly, all components should be examined for defects. If all parts are of satisfactory quality, apply a light layer of adhesive to the connector posts and firmly push the joints together. Apply pressure to each joint for several minutes, until set. After initial bonding, allow the joints to cure for 24 hours before applying forces to the brace. ABS cement or a similar type of plastic resin is recommended as the bonding agent for best results. Supplementary Components

BYOE: A Method for Creating CAD-based, Two-sided Molded Prototype Parts

BYOE: A Method for Creating CAD-based, Two-sided Molded Prototype Parts Paper ID #18086 BYOE: A Method for Creating CAD-based, Two-sided Molded Prototype Parts Dr. Christopher P. Pung, Grand Valley State University Dr. Pung has interests in experiential learning, design processes

More information

1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second)

1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second) Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may not fit in the pump housing. 1. Change

More information

LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets

LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets Set units Create Sketch Add relations Linear patterns Mirror Fillet Extrude Extrude cut First, set units. click Option on top of main menu Open Document Properties

More information

Introduction to Revolve - A Glass

Introduction to Revolve - A Glass Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required

More information

Introduction to 3D CAD with SolidWorks. Jianan Li

Introduction to 3D CAD with SolidWorks. Jianan Li Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,

More information

Lulzbot Taz Workflow Computation + Construction Lab Iowa State University

Lulzbot Taz Workflow Computation + Construction Lab Iowa State University Lulzbot Taz Workflow Computation + Construction Lab Iowa State University 3D Printing on the Lulzbot Taz - Guidelines - The following steps that will guide the user on how to 3D print using the Lulzbot

More information

Below are the desired outcomes and usage competencies based on the completion of Project 4.

Below are the desired outcomes and usage competencies based on the completion of Project 4. Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements

More information

Table of Contents CONTENTS

Table of Contents CONTENTS Table of Contents CONTENTS Introduction... 2 Contact TKI... 2 Printer Features & Definitions... 3 Software Parameter Setup... 8 Setting Up A Printer Profile in Cura... 8 Printing Settings... 13 Printing

More information

User Manual Creatr HS

User Manual Creatr HS 1 Leapfrog BV Dear customer, Congratulations with the purchase of your very own Leapfrog Creatr HS! We would like to help you get started so you can make your first 3D print on the Creatr HS and many more.

More information

For rapid-prototyping and production of low volume, low cost plastic objects.

For rapid-prototyping and production of low volume, low cost plastic objects. 3D Printer Standard Operating Procedure Jonathan M. Cabot 10 January 2016 For rapid-prototyping and production of low volume, low cost plastic objects. 1.0 Material Requirements 1.1 Equipment needed for

More information

Modeling Basic Mechanical Components #1 Tie-Wrap Clip

Modeling Basic Mechanical Components #1 Tie-Wrap Clip Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely

More information

SolidWize. Online SolidWorks Training. Simple Sweep: Head Scratcher

SolidWize. Online SolidWorks Training. Simple Sweep: Head Scratcher SolidWize Online SolidWorks Training Simple Sweep: Head Scratcher Step 1: Creating the Handle: Sketch Using Inches as the unit create a sketch on the Front plane. Start with the sketch shown below: Create

More information

J. La Favre Fusion 360 Lesson 4 April 21, 2017

J. La Favre Fusion 360 Lesson 4 April 21, 2017 In this lesson, you will create an I-beam like the one in the image to the left. As you become more experienced in using CAD software, you will learn that there is usually more than one way to make a 3-D

More information

Intro to 3D Printing. Anatomy of the Printer. Intro to 3D Printing & Certification imagine create learn grow

Intro to 3D Printing. Anatomy of the Printer. Intro to 3D Printing & Certification imagine create learn grow Intro to 3D Printing 3D printing is a process of additive manufacture, this is where layers upon layers of material are built up to create a three dimensional object from a digital design. The 3D printer

More information

SolidWorks Design & Technology

SolidWorks Design & Technology SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one

More information

SolidWorks 95 User s Guide

SolidWorks 95 User s Guide SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents

More information

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B: MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing

More information

E11: Autonomous Vehicles. Lab 2: 3D CAD and Printing

E11: Autonomous Vehicles. Lab 2: 3D CAD and Printing E11: Autonomous Vehicles Lab 2: 3D CAD and Printing The goal of this lab is to create a robot chassis in SolidWorks that can be printed on HMC s 3D printer. When you are done, the chassis should look like

More information

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here. AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and

More information

SPUNKY ASSEMBLY MANUAL

SPUNKY ASSEMBLY MANUAL SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some

More information

SolidWorks & Tinkerine 3D Printing Tutorial ELEC391

SolidWorks & Tinkerine 3D Printing Tutorial ELEC391 SolidWorks & Tinkerine 3D Printing Tutorial ELEC391 Engineering Services, Dept. of Electrical and Computer Engineering University of British Columbia, Faculty of Applied Science Table of Contents Installing

More information

TAZ Lulzbot 3D Printer Standard Operating Procedure [Updated December 21, 2016]

TAZ Lulzbot 3D Printer Standard Operating Procedure [Updated December 21, 2016] TAZ 3 Lulzbot 3D Printer Location of Machine: Composites Lab, RFM 1218 Location of SOP and Machine Operating & Safety Manual: Composites Lab website under resources; Composites Lab TRACS site; and Hardcopy

More information

2.9 WINDOW & DOOR BUCKS

2.9 WINDOW & DOOR BUCKS 2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place

More information

1. Assemble in your groups. 2. Using SolidWorks create a spinning coin, suited for FDM UprintPlus/ Robo 3D R1. Import the Coin_Pattern.

1. Assemble in your groups. 2. Using SolidWorks create a spinning coin, suited for FDM UprintPlus/ Robo 3D R1. Import the Coin_Pattern. MEEN 3349 Fundamentals of Manufacturing Lab 3D Printing Lab (2 week lab) 1. Assemble in your groups. 2. Using SolidWorks create a spinning coin, suited for FDM UprintPlus/ Robo 3D R1. Import the Coin_Pattern.igs

More information

Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).

Hydro Hull. Chapter 21. Boat. A. Save as HYDRO. Step 1. Open your HULL MID PLANE file (Chapter 2). Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,

More information

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

Procedure on construction of each of the following subsystems:

Procedure on construction of each of the following subsystems: Procedure on construction of each of the following subsystems: Chest Cavity with Fittings Diaphragm with wood support Lungs Ribs + Spine Stand (including rib movement system) Section 1: Chest Cavity with

More information

Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software

Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the

More information

Slicer"CURA" User Instructions for Olivetti S2 3D Printer

SlicerCURA User Instructions for Olivetti S2 3D Printer Slicer"CURA" User Instructions for Olivetti S2 3D Printer 1 Cura Install - 1 Click Next 2 Cura Install - 2 Check all components. Then click Install 3 Cura Install - 3 Click Next 4 Cura Install - 4 The

More information

Step 1: Set up the variables AB Design. Use the top cells to label the variables that will be displayed on the X and Y axes of the graph

Step 1: Set up the variables AB Design. Use the top cells to label the variables that will be displayed on the X and Y axes of the graph Step 1: Set up the variables AB Design Use the top cells to label the variables that will be displayed on the X and Y axes of the graph Step 1: Set up the variables X axis for AB Design Enter X axis label

More information

Instructions for using the CRR10: Creality 3D - Our Trustworthy 3D printer

Instructions for using the CRR10: Creality 3D - Our Trustworthy 3D printer Instructions for using the CRR10: Creality 3D - Our Trustworthy 3D printer FABLAB BRIGHTON 2018 Installing Curamaker software The first step is to download the software for this machine. The one we ve

More information

Solid Part Four A Bracket Made by Mirroring

Solid Part Four A Bracket Made by Mirroring C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude

More information

Hephestos 2 Levelling Guide

Hephestos 2 Levelling Guide Hephestos 2 Levelling Guide Version: V0.0.0 Author(s): BQ May 18 th 2018 Revised by: Approved by: Jon Goitia Effect date: 18/05/2018 Project: Hephestos 2 Changelog Version Date Changes Author V0.0.0 May

More information

Ornamental Pro 2010 Component Drawing Manual

Ornamental Pro 2010 Component Drawing Manual Ornamental Pro 2010 Component Drawing Manual Introduction This manual explains the methods for creating your own components for the component library. Component mode is for advanced users only. You must

More information

Pro/DESKTOP Tutorial Drafting Bow Compass

Pro/DESKTOP Tutorial Drafting Bow Compass Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.

More information

Datum Tutorial Part: Cutter

Datum Tutorial Part: Cutter Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis

More information

ideamaker Manual

ideamaker Manual ideamaker Manual Using ideamaker... 2 1 Basic information... 2 1.1 What is ideamaker?... 2 1.2 Where to download ideamaker?... 2 2 Install ideamaker... 3 3 Let s Print!... 6 4 How to use ideamaker?...

More information

Using Siemens NX 11 Software. The connecting rod

Using Siemens NX 11 Software. The connecting rod Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open

More information

Slicer"CURA" User Instructions for Olivetti 3D DESK

SlicerCURA User Instructions for Olivetti 3D DESK Slicer"CURA" User Instructions for Olivetti 3D DESK 1 Cura Install - 1 Click Next 2 Cura Install - 2 Check all components. Then click Install 3 Cura Install - 3 Click Next 4 Cura Install - 4 The Wizard

More information

Autodesk Inventor. In Engineering Design & Drafting. By Edward Locke

Autodesk Inventor. In Engineering Design & Drafting. By Edward Locke Autodesk Inventor In Engineering Design & Drafting By Edward Locke Engineering Design Drafting Essentials Working Drawings: Orthographic Projection Views (multi-view, auxiliary view, details and sections)

More information

Engineering Innovation Center Autodesk Fusion 360

Engineering Innovation Center Autodesk Fusion 360 Engineering Innovation Center Autodesk Fusion 360 Introduction The Engineering Innovation Center is a large academic maker space with plenty of tools and equipment. In order to use these items you must

More information

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define. BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of

More information

Siemens NX11 tutorials. The angled part

Siemens NX11 tutorials. The angled part Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure

More information

Shaft Hanger - SolidWorks

Shaft Hanger - SolidWorks ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric

More information

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch. Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.

More information

Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder

Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic

More information

XYZware User Manual. XYZware User Manual P 1

XYZware User Manual. XYZware User Manual P 1 XYZware User Manual P 1 Announcement Limitation of Liability Clause Although it is our intention to produce a manual and product functions that are correct and stable, in no event shall XYZprinting be

More information

Diane Burton, STEM Outreach.

Diane Burton, STEM Outreach. 123D Design Tutorial: LED decoration Before using these instructions, it is very helpful to watch this video screencast of the CAD drawing actually being done in the software. Click this link for the video

More information

How to Draw a New York Beauty Block

How to Draw a New York Beauty Block How to Draw a New York Beauty Block We start by opening the Block Wizard. Click Options, Screen settings. In the Grid tab, choose Circular for the Grid Type. Set the Size to be.50 Number of Rings: 15 Radials:

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

XYZware User Manual. XYZware User Manual P 1

XYZware User Manual. XYZware User Manual P 1 XYZware User Manual P 1 Announcement Limitation of Liability Clause Although it is our intention to produce a manual and product functions that are correct and stable, in no event shall XYZprinting be

More information

Straw support Fusion 360

Straw support Fusion 360 Straw support Fusion 360 Before using these instructions, watch the video screencast of the CAD drawing actually being done in the software. Click this link for video tutorial This design works on a variety

More information

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. Engineering Design with SolidWorks 2003 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com

More information

Assembly Guide for Printrbot - Simple Maker s Edition 1405

Assembly Guide for Printrbot - Simple Maker s Edition 1405 Assembly Guide for Printrbot - Simple Maker s Edition 1405 Last update: March 2016 Please Note: be careful on the steps that are underlined 1 Contents Tools Needed:... 3 First step: Check components and

More information

Official Guide to Certified SolidWorks Associate Exams: CSWA, CSDA, CSWSA-FEA

Official Guide to Certified SolidWorks Associate Exams: CSWA, CSDA, CSWSA-FEA Official Guide to Certified SolidWorks Associate Exams: CSWA, CSDA, CSWSA-FEA SolidWorks 2012-2015 An authorized CSWA preparation exam guide with additional information on the CSDA and CSWSA-FEA exams

More information

WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer

WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer 1. Creating the Shaft Model 1. File> New> Part, Name: C51X01> OK 2. Insert> Revolve> Placement> Define> select TOP datum plane> Sketch

More information

SETUP INSTRUCTIONS If you would like to tell us about your experience with your setup instructions please us at

SETUP INSTRUCTIONS If you would like to tell us about your experience with your setup instructions please  us at 207 VK-964 General Layout 0 0 Plan View www.classicexhibits.com SETUP INSTRUCTIONS If you would like to tell us about your experience with your setup instructions please email us at info@classicexhibits.com

More information

Purlin Roof. Create a New Folder in your chosen location called Purlin Roof. The nine parts that make up the project will be saved here.

Purlin Roof. Create a New Folder in your chosen location called Purlin Roof. The nine parts that make up the project will be saved here. Purlin Roof Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Add Relations, Dimensioning), Inserting Planes, Extrude,

More information

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05 Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating

More information

Foreword. If you have any questions about these tutorials, drop your mail to

Foreword. If you have any questions about these tutorials, drop your mail to Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what

More information

AM8 Printer A metal frame for your Anet A8 By Pheneeny v1.0 April 20, 2017

AM8 Printer A metal frame for your Anet A8 By Pheneeny v1.0 April 20, 2017 AM8 Printer A metal frame for your Anet A8 By Pheneeny v1.0 April 20, 2017 Please read this entire document before printing parts or building this frame Disclaimer: This guide is for informational purposes

More information

Provided: 1.3, 1.5 and 2 mm hex wrenches. Not Provided: Small flat head screw driver, pliers/adjustable. wrench.

Provided: 1.3, 1.5 and 2 mm hex wrenches. Not Provided: Small flat head screw driver, pliers/adjustable. wrench. Note: These instructions are a work in progress, and DualStrusion is intended only for bleeding-edge experimenters. The MakerBot Stepstruder MK7 is the first extruder for the MakerBot Thing-O-Matic to

More information

Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge

Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored

More information

UNIT 11: Revolved and Extruded Shapes

UNIT 11: Revolved and Extruded Shapes UNIT 11: Revolved and Extruded Shapes In addition to basic geometric shapes and importing of three-dimensional STL files, SOLIDCast allows you to create three-dimensional shapes that are formed by revolving

More information

Introduction to Autodesk Inventor for F1 in Schools (Australian Version)

Introduction to Autodesk Inventor for F1 in Schools (Australian Version) Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital

More information

Fibre Cement Board The first tile backing system with a lifetime guarantee

Fibre Cement Board The first tile backing system with a lifetime guarantee Installation Guide NoMorePly.net NoMorePly - Guarantee and guidance Lifetime Guarantee Terms The NoMorePly board lifetime guarantee only applies when the correct installation procedures, as set out in

More information

Introducing SolidWorks

Introducing SolidWorks Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions

More information

Applications Engineering Notes

Applications Engineering Notes Applications Engineering Notes Document Title Document Number Operating Instructions for the US Conec AEN-1408 Revision Number 1.0 Effective Date December 15, 2011 THE USE OF SAFETY GLASSES FOR EYE PROTECTION

More information

Introduction to Sheet Metal Features SolidWorks 2009

Introduction to Sheet Metal Features SolidWorks 2009 SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to

More information

Design Analysis Process

Design Analysis Process Prototype Design Analysis Process Rapid Prototyping What is rapid prototyping? A process that generates physical objects directly from geometric data without traditional tools Rapid Prototyping What is

More information

Using Cura for the first time

Using Cura for the first time Cura User manual Using Cura for the first time Initial startup When you start Cura you will be greeted by the following wizard: This wizard will guide you through your initial checkup and calibration of

More information

Ornamental Pro 2004 Instruction Manual (Drawing Basics)

Ornamental Pro 2004 Instruction Manual (Drawing Basics) Ornamental Pro 2004 Instruction Manual (Drawing Basics) http://www.ornametalpro.com/support/techsupport.htm Introduction Ornamental Pro has hundreds of functions that you can use to create your drawings.

More information

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects Engineering Design with SolidWorks 2010 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Introductory Level

More information

Engineering & Computer Graphics Workbook Using SolidWorks 2014

Engineering & Computer Graphics Workbook Using SolidWorks 2014 Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

MakerBot Replicator+ 3D Printer

MakerBot Replicator+ 3D Printer MakerBot Replicator+ 3D Printer Quick Start Guide *Safety Warning* During the course of normal operation of the Replicator+ a couple potentials for injury will arise. The extruder (or print nozzle) will

More information

How to 3D Print molds for custom

How to 3D Print molds for custom How to 3D Print molds for custom Stamps @ustreasury Created by phillip torrone Last updated on 2017-10-04 01:23:10 AM UTC Guide Contents Guide Contents Overview Parts Two part mold putty Ultimaker 2+ 3D

More information

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing a Bloodhound Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks

More information

CURA WANHAO EDITION USER MANUEL

CURA WANHAO EDITION USER MANUEL CURA WANHAO EDITION USER MANUEL 1.1 Cura Overview We recommend that new users start with Cura as it includes a slicing engine. Host software we recommend to use Repitator. There is separate introduction

More information

g. Click once on the left vertical line of the rectangle.

g. Click once on the left vertical line of the rectangle. This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required

More information

Manual Leapfrog Creatr

Manual Leapfrog Creatr 1 Leapfrog BV Dear customer, Congratulations with the purchase of your very own Leapfrog Creatr Single or Dual Extruder! We would like to help you get started so you can make your first 3D print on the

More information

Sentinel Armor Kit Assembly Guide

Sentinel Armor Kit Assembly Guide 1 Sentinel Armor Kit Assembly Guide 2 Thank you for purchasing the Mynock s Den Collection Sentinel Armor Kit by Vader s Vault. This guide will help you assemble your new kit, so be sure to keep it close

More information

Engineering & Computer Graphics Workbook Using SOLIDWORKS

Engineering & Computer Graphics Workbook Using SOLIDWORKS Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

3D Printing with the Lulzbot 4 Alyssa Schwartz on 7/2/2018

3D Printing with the Lulzbot 4 Alyssa Schwartz on 7/2/2018 3D Printing with the Lulzbot 4 Alyssa Schwartz on 7/2/2018 1. Find or Design your Object. This can come from almost any source, but needs to be in a.stl file format. a. Thingiverse.com b. https://3dprint.nih.gov/

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better

More information

Installation - Sub Cills

Installation - Sub Cills Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings

More information

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered

More information

The Nantucket Legacy Arbor

The Nantucket Legacy Arbor ASSEMBLY INSTRUCTIONS 0. in 9 in 0. in 68 in 7 in in *Nantucket Legacy with Trim Kit Shown Above. Please read through before starting assembly. in 60 in 0 in 8 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS

More information

Toothbrush Holder Project 2D Machining

Toothbrush Holder Project 2D Machining Toothbrush Holder Project 2D Machining Prerequisite Toothbrush Holder drawn and saved as a DXF file in SolidWorks Focus of the Lesson On completion of this exercise you will have: Used the Techsoft 2D

More information

TABLE OF CONTENTS. About Ultimaker. Fused Filament Fabrication. Capabilities. Considerations

TABLE OF CONTENTS. About Ultimaker. Fused Filament Fabrication. Capabilities. Considerations Ultimaker Tutorial TABLE OF CONTENTS About Ultimaker... 1 Prepare Your File for Printing... 2 Logging the Print... 8 Preparing the Machine... 9 Paying for Your Part... 11 Printing Your Part... 12 Removing

More information

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. 2001Plus A Competency Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com Project 2 Below are the desired

More information

B A T H R O O M G L A S S

B A T H R O O M G L A S S mistley B A T H R O O M G L A S S vaug16 Page 2 Thank you for purchasing this Trinity shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts

More information

CURA WANHAO EDITION USER MANUEL

CURA WANHAO EDITION USER MANUEL CURA WANHAO EDITION USER MANUEL 1.1 Cura Overview We recommend that new users start with Cura as it includes a slicing engine. Host software we recommend to use Repitator. There is separate introduction

More information

Timberflex & Flexboard Technical Guide

Timberflex & Flexboard Technical Guide Timberflex & Flexboard Technical Guide A bendable substrate material that can be formed first and laminated last Patent #5,618,601; #5,232,762; #5,824,382 Doors Larger radius and small doors are easily

More information

CONTENTS OVERVIEW. For a complete set of CAD drawing details, please visit LaminatorsInc.com. 1 Essential Equipment. 1 Essential Supplies

CONTENTS OVERVIEW. For a complete set of CAD drawing details, please visit LaminatorsInc.com. 1 Essential Equipment. 1 Essential Supplies LaminatorsInc.com CONTENTS 1 Essential Equipment 1 Essential Supplies 2 Panel Preparation 4 Panel Extrusion Preparation 5 Panel Assembly 6 Wall Sheathing Preparation (Over Plywood) 6 Wall Sheathing Preparation

More information

Essentials of SOLIDWORKS 2015 (4+ Days) * Ve-I Bonus! * File Management + SimulationXpress

Essentials of SOLIDWORKS 2015 (4+ Days) * Ve-I Bonus! * File Management + SimulationXpress Essentials of SOLIDWORKS 2015 (4+ Days) * Ve-I Bonus! * File Management + SimulationXpress Overview What is SOLIDWORKS? Interface Tour View Manipulation Provides some background info on the SOLIDWORKS

More information

BUILD 3 Tri-Color Candy Corn

BUILD 3 Tri-Color Candy Corn BUILD 3 Tri-Color Candy Corn 1. Go to www.tinkercad.com and SIGN UP for a free account then Sign In 2. Select the Create new design button to open the editing screen 3. Select Properties from the Design

More information

Solidworks Tutorial Pencil

Solidworks Tutorial Pencil The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following

More information

Curium 19H Installation Instructions & Parts List

Curium 19H Installation Instructions & Parts List Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified

More information

Separation Connector. Prototyping Progress Update March 1, 2013

Separation Connector. Prototyping Progress Update March 1, 2013 Separation Connector By Koll Christianson, Luis Herrera, and Zheng Lian Team 19 Prototyping Progress Update March 1, 2013 Submitted towards partial fulfillment of the requirements for Mechanical Engineering

More information

Advance Dimensioning and Base Feature Options

Advance Dimensioning and Base Feature Options Chapter 4 Advance Dimensioning and Base Feature Options Learning Objectives After completing this chapter you will be able to: Dimension the sketch using the autodimension sketch tool. Dimension the sketch

More information