Assembly Instructions-C1 Amphenol UHF
|
|
- Anthony Ward
- 6 years ago
- Views:
Transcription
1 Assemly Instrutions-C1 Amphenol UG STANDARD SOLDER TYPE PLUGS 83-1SP, 83-1SP-1050, 83-1SP-15RFX, oupling ring plug su-ssemly Amphenol Connetor Cle Atthment Dt Stripping Dimensions, inhes (mm) Numer Type RG-/U Outer Inner 83-1SP-1050 Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) 83-1SP Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) 83-1SP-15RFX Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.13(28.6).689(17.5).625(15.9) Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) Angle Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder.844(21.4).391(9.9).250(6.4) Angle Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder.844(21.4).391(9.9).250(6.4) A B C Slide oupling ring onto le. Cut end of le even nd strip jket, rid nd dieletri to dimensions shown in tle. All uts re to e shrp nd squre. Do not nik rid, dieletri or enter ondutor. Tin exposed enter ondutor nd rid, voiding exessive het. SOLDER solder HERE here Srew the plug su-ssemly on le. Solder ssemly to rid through solder holes, mking good ond etween rid nd shell. Solder ondutor to ontt. Do not use exessive het. For finl ssemly on stright plugs, move oupling ring forwrd nd srew in ple on plug su-ssemly. 274
2 Assemly Instrutions-C2 Amphenol UG STANDARD SOLDER TYPE WITH REDUCING ADAPTER FOR PLUGS 83-1SP, 83-1SP-1050, 83-1SP-15RFX, , USING RFX, OR , RFX REDUCING ADAPTER oupling ring or RFX for RG-59 plug su-ssemly or RFX for RG-58 reduing dpter Cle RG-/U Cle RG-/U Atthment Dt Using or Using RFX or RFX Amphenol Connetor (using (using Numer Type Stripping Dims, inhes (mm) Stripping Dims, inhes (mm) or RFX) or RFX) Outer Inner 83-1SP Plug Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-1SP-1050 Plug Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-1SP-15RFX Plug Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) Plug Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) Plug Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) Assemly A B Slide oupling ring nd dpter onto le. Cut end of le even nd strip jket to dimension shown in tle. C Position dpter flush with end of le jket. Fn rid slightly nd fold k over ody of dpter s shown. Press rid down over ody nd trim to dimension. Bre ondutor to dimension shown in tle. Tin exposed enter ondutor nd rid, voiding exessive het. solder SOLDER HERE here Srew plug su-ssemly onto dpter. Solder rid to shell through solder holes, mking good ond etween rid nd shell. Solder ondutor to ontt. Do not use exessive het. Step 4 STEP 4 Step 4 For finl ssemly, srew oupling ring onto plug su-ssemly. 275
3 Assemly Instrutions-C4, C5 Amphenol C4 BRAID CRIMP - SOLDER CENTER CONTACT ferrule oupling nut ody ssemly Amphenol Connetor Cle Cle Atthment Hex Crimp Dt Stripping Dims, inhes (mm) Numer Type RG-/U Cvity for Die Set CTL Series Outer Inner Outer Ferrule Tool Tool No SP Plug 58, 141 Crimp Solder.213(5.4) CTL (29.0).780(19.9).250(6.4) 83-58SP-1002 Plug 400 Crimp Solder.213(5.4) CTL (29.0).780(19.9).250(6.4) 83-59DCP-RFX Plug 59 Crimp Solder.255(6.5) CTL (30.9).574(22.6).543(13.8) 83-58SCP-RFX Plug 58 Crimp Solder.213(5.4) CTL (30.9).574(22.6).543(13.8) 83-59SP Plug 59 Crimp Solder.255(6.5) CTL (30.9).574(22.6).543(13.8) 83-8SP-RFX Plug 8 Crimp Solder.429(10.9) CTL (30.9).574(22.6).543(13.8) A B C Cut end of le even. Strip le to dimensions shown in tle. All uts re to e shrp nd squre. Do not nik rid, dieletri or enter ondutor. Tin enter ondutor voiding exessive het. BRAID rid AFTER fter FLARINGflring ody ssemly BODY ASSEMBLY Slide oupling nut nd ferrule over le jket. Flir rid slightly s shown. Instll le into ody ssemly, so inner ferrule portion slides under rid, until rid utts shoulder. Slide outer ferrule over rid until it utts shoulder. Crimp ferrule with tool nd die set indited in tle. Soft solder enter ondutor to ontt. Avoid heting ontt exessively to prevent dmging insultor. Slide/srew oupling nut over ody. C5 CRIMP-CRIMP TYPE-C5 outer ferrule oupling nut ody ssemly Cle Atthment Hex Crimp Dt CTL Die Set Amphenol Connetor Cle Numer Type RG-/U Cvity for Cvity for Cvity for Series for Tool Outer Inner Outer ferrule End of Ferrule Center Contt Tool # DCP-2 Plug 58 Crimp Crimp.260(6.60).210(5.33).052(1.32) sq. 1.23(31.3).791(20.2).25(6.35) DCP-2RFX Plug 58 Crimp Crimp.255(6.5).213(5.4).068(1.7) 1.12(28.4).685(17.4).236(5.99) CTL , (31.3).791 (20.2).250 (6.4) Strip le to dimensions shown. Slide ferrule nd oupling nut over le jket nd flir rid slightly s shown. rid BRAID AFTER fter FLARINGflring ody ssemly CRIMP (3) rimp (3) CRIMP (1) rimp (2) CRIMP (2) rimp Slide ody ssemly into ple so inner ferrule portion slides under rid. Brid must utt k of ody. Slide oupling nut forwrd. Slide ferrule over rid until it utts ginst ody. Using tools indited in tle ove: (1) rimp enter ontt (2) rimp outer ferrule to rid (3) rimp outer ferrule to le jket 276
4 Assemly Instrutions-C6 Amphenol FCP TERMINATION FOR PLUGS 83-58FCP, 83-58FCP-RFX on RG-58 BARB r enter CENTER CONTACT ontt shoulder SHOULDER ferrule oupling nut ody ssemly TIP tip Amphenol Connetor Cle Stripping Dimensions, inhes (mm) Tools Numer Type RG-/U 83-58FCP FCP Plug 58 Pliers & Fier Grommet in Bg 1.00(25.4).812(20.6).500(12.7) 83-58FCP-RFX FCP Plug 58 Pliers & Fier Grommet in Bg.673(17.0).547(14.0).236(6.0) Assemly A B C Strip le to dimensions shown in tle. rid BRAID AFTER fter FLARINGflring Slide ferrule nd oupling nut over le. Flir rid slightly. Insert ody under flred rid until shoulder is ginst le jket. rid BRAID trim ondutor fter ssemly TRIM CONDUCTOR AFTER ASSEMBLY Slide nut onto ody. Grsp le. Push ferrule over r nd up ginst ody. Crimp tip of enter ontt with pliers, or if you prefer, solder. Then trim enter ondutor even with end of ontt. 277
5 Assemly Instrutions-C7 Amphenol HOODS FOR ADAPTING PANEL RECEPTACLES TO COAXIAL CABLES 83-1H (UG-106/U) for RG-8, 10, 11, 12, 63, 79, 115, 149, 213, (UG-177/U) for RG-58, H 83-1H Amphenol Connetor Cle Cle Atthment Stripping Dimensions Numer Type RG-/U Outer Inner 83-1H Hood 8, 10, 11, 12, 63, 79, 115, 149, 213, 205 Solder Solder.625(15.8).500(12.7).312(7.92) Hood 58, 141 Solder Solder.750(19.0).687(17.4).312(7.92) Strip le to dimensions shown. Do not nik enter ondutor. Tin exposed rid nd enter ondutor. SOLDER solder CABLE CENTER le enter ondutor CONDUCTOR INTO SOLDER CUP TERMINAL into solder up terminl Slide hood over rid. When using doule-rided le, hood goes over inner rid only. Then, in step 3, solder outer rid to outside of hood. Solder Center Condutor into solder up terminl. tpe or tuing over this setion TAPE OR TUBING OVER THIS SECTION TACK SOLDER FLANGES TOGETHER tk solder flnges together Slide hood flush ginst reeptle nd tk-solder hood flnge to reeptle flnge. Solder hood to rid s shown. Use tpe or tuing over setion shown. solder here for SOLDER HERE FOR ALL AROUND BACK OF HOOD SOLDER solder HERE FOR here 83-1H for 83-1H THREE SOLDER HOLES three solder holes 278
D Subminiature Combo D
Cable ( 8) Loose Contacts Coaxial 75 Ohm Stamped Crimp/Crimp Recommended Wire Trim Dimensions Kit (ody, Ferrule, Center Contact) Stamped Crimp/Crimp Kit Kit 30 in. Kit 50 in. RG Cable Number D130322-2
More informationAmphenol RF UHF. UHF Connector Series UHF. Description. Features/Benefits. Applications
Amphenol RF 136 Connector Series Description Invented in the 1930 s by an Amphenol Engineer named E. Clark Quackenbush, coaxial connectors are general purpose units developed for use in low frequency systems
More informationBNC Connectors. General Description. BNC Configurations. BNC Specifications* Plug Interface** Jack Interface**
N onnectors General Description Delta N connectors are compact, economical, 50Ω impedance connectors with two-stud bayonet coupling. They are best suited for use with cables in the range of.150" to.50"
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationAmphenol RF Interconnects BNC 31 Series Bayonet Lock RF Connector System
BNC 31 Series Bayonet Lock RF Connector System Materials Body/Finish /Nickel Centre MALE Centre FEMALE Phosphor Bronze Centre Finish Gold 30µ Insulator Delron/PBT Gasket Silicone Rubber Crimp s Annealed
More information711 Series Single Way DB-1a
711 Series Single Way DB-1a Data Bus Interconnection System Data Bus Interconnection System designed for data transmission as defined by MIL-STD-1553B, STANAG 3838 and DEF STAN 00-18 (Part 2). This system
More informationMobile Gain Antennas MHz Models RRA-4935/RRA-4936
890-960 MHz Models RRA-4935/RRA-4936 Installation See Table 1 for recommended antenna location for various vehicles. The installation procedure which follows is for a typical passenger car. The procedure
More informationTNC Connectors. General Description. TNC Configurations. TNC Specifications* Plug Interface** Jack Interface**
TN onnectors General Description Delta TN connectors are compact, 50 Ω impedance connectors with 7 16-28 threaded coupling, similar in size to N connectors but with better electrical characteristics. They
More informationGORE Aerospace Ethernet Cables
Termination Instructions The following procedures are based on Gore s best practices for terminating GORE Aerospace with the Amphenol Oval Contact System (OCS) for both plug and receptacle versions. These
More informationUPC-LL Power Connection Kit
Installation Instructions UPC-LL Power Connection Kit for Series Long Line Heating Cables 1 PJ951 161-562681-020 July 2015 UPC-LL End Termination Kit Kit Contents Item Qty Description Item Qty Description
More informationTNC SERIES General... 4 Interface... 5 Characteristics...6-7
CONTENTS PAGE TNC SERIES General... 4 Interface... 5 Characteristics...6-7 TNC 50 Ω SERIES Plugs...8-9 Jacks...0- Jacks and receptacles... Receptacles...-4 Adapters... 5 Caps... 6 TNC 75 Ω SERIES Plugs...
More informationGORE Aerospace Ethernet Cables
Termination Instructions The following procedures are based on Gore s best practices for terminating GORE Aerospace with the Carlisle Octax Connector System for both socket and plug versions. These procedures
More information1/8" Balsa 8B 7B 6B. For Radio Control. Wingspan - 25" CAD Drawing by Paul Bradley Sheet 1 of 12 INCHES. Cowl pattern.
R1 1/8" alsa R2 owl pattern 1/16" Square enter Windshield Pattern 1/16" Square filler forward of stab 9T 8T 7T R3 10 R4 T1 T2 9 Side Windows Pattern Fuselage sides are built using 1/16" square stock 8
More informationSKDG Cable Repair Kit Instructions
SKDG Cable Repair Kit Instructions Description Having to repair your EasyHeat cable is an extremely rare occurrence. Damage is almost always a function of field conditions, such as impacts with tools.
More informationUltimate Flip Lever Astragal Prehanger Installation Instructions
Ultimte Flip Lever Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Tpe Mesure Kit Includes: Full Astrgl Full Length Trim Strip Screw Pck Field Pck
More informationTools for crimp contacts
Tools for crimp termination D-Sub-S, D-Sub-HD, DIN 41 612 Identification Service crimp tool standard contacts high density contacts Part No. 09 99 000 0175 09 99 000 0596 HARTING- Crimp tool for 500 bandoliered
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationWater Level Meter: Op Instructions
Equipment Check 1. Turn sensitivity switch fully clockwise. Notes: 1. Clockwise rotation of sensitivity swsitch turns meter on and increases sensitivity. 2. Always set switch to highest sensitivity position,
More informationNo crimping is required just solder the the wire to the crimp piece and use some heat shrink tubing to cover the end of the crimp.
In this section we will be wiring up the IEC socket (AC plug) with the rocker switch and the Mains transformer primaries. Follow these instructions if you live in an area with 100, 110, 220 or 230 Volts!"
More informationRFX. Type N RG58, 141, 142 Straight Plug Type N Connectors» Cable Straight. Jack 50 Ohm Yes
Please note: Images are for reference only Amphenol Part Number: Description: Product Series: Product Type: Connector Body Style: Gender: Impedance: RoHS Compliant: 082-5376-RFX RG58, 141, 142 Straight
More informationBel Stewart Connector
Page 1 of 8 PLUG ASSEMBLY INSTRUCTIONS FOR Cable with INDIVIDUALLY SHIELDED PAIRS (PIMF or SFTP) T568B Wiring Pattern For Cable with Overall Foil Shield (FTP), See Page 9 1 2 Cut cable to length. If you
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationBroadband performance with low reflection DC to 4 GHz provides low cost connector combined with high quality.
Amphenol RF 36 Connectors Description The name derives from SubMiniature B (the second subminiature design). Developed in the 1960 s, this sub miniature interface has snap-on coupling. Amphenol s connectors
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationTechnical Information
UTO Series Technical Information Tooling... 2 Crimping Instructions... 3 Handle & Interchangeable Heads... 5 Extraction Tools... 6 Assembly Instructions... 7 1 Tooling Standard contacts Contact size #12
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationMODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS
MODEL POWERGLIDE SERIES INSTRUTIONS FOR INSTLLING SRGENT LOSERS WITH "H" HOLDER S SERIES NON SIZED DJUSTLE SIZES THRU 6 UTION: FILURE TO INSTLL OR DJUST PROPERLY MY RESULT IN INJURY OR DMGE. FOR SSISTNE,
More informationMale Cable Connectors / Female Receptacles Male cable connector straight, with internal strain relief clamp and/or clamping ring, cable diameter 6-12,5 mm No. of contacts 3 + PE 3 + PE Termination technique
More informationPowerpole General Assembly Instructions
Powerpole General Assembly Instructions The contacts go in the housings in only one way. Insert the contacts with their sharp edge down against the flat spring that is in the housing. They should slide
More informationSMB Connectors, 50 Ohm
SM Connectors, 50 Ohm Straight Plugs Max. 21.10 [.830] Max. Outer Other Metal s Dielectric Style 178, 178, 178, 196, 196 Gold Gold Nickel TEFLON MIL 413985-6 MIL 413985-1 Gold Gold Nickel TEFLON MIL 413985-3
More informationMIL-STD B (SH) UPDATE
MIL-STD-2042-5B (SH) UPDATE Method 5A1 Insert Equipment and materials (to be added to table 5A1-I) Pliers 3.2.2.2 Cable and fiber preparation for Fiber Systems International backshells. Step 1: Ensure
More informationWater Line and Water Line Assembly Gasket
1 Preparation for Repair 1) Remove tip from scaler 2) Remove scaler from air supply 3) Remove gasket from back end of scaler. Examine gasket for obvious wear or disfigurement. Replace if necessary. 2 Remove
More informationSpiderbeam Balun Construction Guide
BALUN CONSTRUCTION GUIDE Ver. 1.0 1 The components of the Balun Kit are in a plastic bag. Most of the components are inside the plastic case of the balun. The aluminum U-profile and the RG-142 Teflon Coax
More informationSUPERSEDED REVISION. Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.
PRO BEAM Jr. EB cable plug connectors are designed to be installed onto jacketed fiber optic cable with KEVLAR strength members. The connector must be assembled using a cable plug connector shell kit,
More informationR/L, AND LXE TYPE CABLE
OFS Fitel Figure 1. FOR CROSSPLY, R/L, AND LXE TYPE CABLE 636-299-110-05 Comcode: 847 815 297 12A1 Cable Clamp Issue 2 March 2002 2002 OFS Fitel All Rights Reserved Printed in U.S.A. Page 1 of 6 12A1 CABLE
More informationCannon Trident Connectors
Power Contacts APK Power Contacts Socket Pin 30 A current rating. For use with Neptune connectors. Part Number Wire Range Wire Loose (100) Reeled (3000) Insulation Strip mm 2 Size Contact Description*
More informationAMPHENOL CORPORATION Amphenol Industrial. Termination Instructions: L-1295 SAE AS50151, AC, ACA and GT Series Solder and Crimp
AC and SAE AS50151 AMPHENOL CORPORATION Industrial ACAB and GT Series Threaded Standard Cylindrical Connectors AMPHENOL CORPORATION Industrial Phone: 8883649011 191 Delaware Avenue Sidney, NY 138381395
More informationProduct Manual MNX10050 / REV B MODELS:
VIBRATION ANALYSIS HARDWARE Product Manual MNX10050 / REV B MODELS: CC-AXX & JXX CC-C2X & C3X Field Installable Connector Kits Contents Section I Overview Introduction... 2 Description... 2 Section II
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationNORTH STAR 4-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T Phone: (519) 637-7899 Toll Free: (800) 65-5701 Fax: (519) 637-3403 Web Site: www.northstarwindows.com NORTH STR 4-PNEL PTIO DOOR SSEMLY INSTRUCTIONS (JN/P-Dr04/4Panssy
More informationSSMC Connectors. Microminiature, screw-on mating High performance to 12.4 GHz. General Description
SSMC Connectors Microminiature, screw-on mating High performance to 12.4 GHz General Description Delta SSMC connectors are microminiature, 50Ω impedance connectors with 6-40 threaded coupling. SSMC connectors
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationSplice-In Sequential Tail Lights Installation Guide (96-04)
Splice-In Sequential Tail Lights Installation Guide (96-04) The below installation instructions work for the following products: Mustang Sequential Taillights Kit - Splice-in (96-04) Please read through
More informationBuilder s Log Helicycle N750G
Here you can see the very tight clearance between the rod end and the top of the shortened castle nut (red arrow.) The last step will be to drill the cotter pin hole in the end of the bolt. NOTE: Accepted
More informationTermination of D-621 Triaxial Connectors to Shielded Twisted Pair Cable for MIL-STD-1553B Applications
1 of 18 Termination of D-621 Triaxial Connectors to Shielded Twisted Pair Cable for MIL-STD-1553B Applications This Engineering Standard forms a part of Engineering Standard ES-61162: "D-621 Connectors
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationITT Cannon Combination D-Sub Connectors
PPLICTIONS Video Coaxial Transmission (75Ω) RF and Telecom Transmission (50Ω) Power Interconnects (Up to 40) ITT Cannon Combination D-Sub Connectors RECTNGULR CONNECTOR SUITED FOR NETWORK ND COMMUNICTION
More informationAMPLIMITE Cable Connectors and Shielding Hardware Kits
AMPLIMITE Cable Connectors and Shielding Hardware Kits Quick Reference Guide We offer one of the broadest, most versatile portfolios of D-subminiature connectors in the market with unrivaled engineering
More informationReasons for reissue are in Section 6, REVISION SUMMARY.
Figure 1 This instruction sheet covers the application of OPTIMATE FSMA Fiber Optic Connector Types 905 and 906 for data and telecommunications applications. Base part numbers which apply to each type
More informationsealed mini usb connectors
QUICK CONNECT CABLE END MATES WITH PANEL MOUNT PANEL MOUNT MATES WITH CABLE END REAR VIEW - PC TAIL REAR VIEW - FEED-THRU TERMINATION REAR VIEW - SOLDER HOLES SPECIFICATIONS Mechanical Specifications Life:
More informationSERIESN50, COAXIAL CONNECTORS
SERIESN50, COAXIAL CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER N connectors are available with 50 and 75 impedance. The frequency range extends to 18 GHz, depending on the connector and cable type.
More informationProduct Manual MNX10050 / REV C MODELS:
VIBRATION ANALYSIS HARDWARE Product Manual MNX10050 / REV C MODELS: CC-AXX & JXX CC-C2X & C3X CC-V2R & V3R Field Installable Connector Kits Contents Section I Overview Introduction... 2 Description...
More informationContacts, Tools, and Accessories
ontacts, Tools, and ccessories able reduction sleeve REDUTION SLEEVEs FOR BLE Reduction Sleeve Length for use with Mechanical able lamp or Basketweave able Grip Shell Sleeve P/N Sleeve inner diameter [mm]
More informationCRIMP CONNECTORS & ACCESSORIES Universal Crimp Termination System. Heavy-duty lightweight stamped steel frame.
Universal Crimp Termination System Extron Universal Crimp Tool Four in One Coax BNC Connector Crimp Tool The affordable heavy-duty Universal BNC Crimp Tool was designed by Extron to be the single tool
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Ultra Antenna These instructions will lead
More informationCABLE-MONITOR (REF) ROUTE THRU ROOF COVE, DOWN A-POST TO RADIO ROUTE TEMPERATURE SENSOR THROUGH FIREWALL BOOT IN THIS AREA SENSOR-TEMPERATURE (REF)
LE-MONITOR ROUTE THRU ROOF OVE, OWN -POST TO RIO ROUTE TEMPERTURE SENSOR THROUGH FIREWLL OOT IN THIS RE SENSOR-TEMPERTURE LG SREEN-INFO/GPS SIRIUSXM OES/STNRS-S/MVSS OES/STNRS US OPYRIGHT 0 WINNEGO INUSTRIES,
More information1.0 Receiver TAC Contact Insertion/Extraction. 2.0 TAC (Receiver) Module Installation/Removal. 3.0 Wiring Contact Insertion/Extraction
Downloadable Documents (Adobe Acrobat (TM) format) Click on the links below to view or download copies of VPC User Manual in Adobe Acrobat (.PDF) format. Note: If you would like printed copies of any of
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationHydraulics are AMAZING! Use the power of water to control a machine. This guide will help you create your own Advanced Hydraulic Arm.
Hydraulics are AMAZING! Use the power of water to control a machine. This guide will help you create your own Advanced Hydraulic Arm. Perfect for Grades: 7+ Difficulty: Advanced Download Documents at teachergeek.com
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS UTS LC Series BT 304 BT304 UTS LC Series Contents Tool & Material... 4 UTS LC Component details... 5 UTS LC Dimensions... 5 Assembly Instructions for UTS1JC18LCN & UTS6JC18LCN...
More informationC WIRE ASM-IP,MAIN
WIRE SM-E LIFT 90-0-000 TO GROUN STU PIN HOUSING TO ROOF PIN HOUSING TO ROOF SPEKER 909-0-000 () G-0-0U () N FN-EFROSTER -0-HT () G9-0-E () UTT SPLIE TO FNS LE-GRN LF-YEL XW-LK PIN HOUSING ONNETS TO WIRE
More informationFooter & Base Plate Assembly. installation guide. ILINE power/data beam
Phase Footer & Base Plate Assembly installation guide ILINE power/data beam Phase Materials and Tools. ILINE Postsleeve Components Top Cap Data Face Plate Post Sleeve Post Sleeves shipped with orders after
More informationIT - ITS - ITS-RG - ITZ Connectors
CONNECTOR CONTCTS Series Presentation Contacts in this chapter can be used for the following circular connector series: IT, ITZ, ITS and ITS RG. Threaded IT series have been designed to be fully conform
More informationPage 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with
More informationElectrical dielectric withstanding voltage. sea level Vrms Vrms m Vrms Vrms
Applications Mechanical and electrical interface between on-board civil avionics equipments and racks Standards Arinc 600 Characteristics Mechanical material finish aluminum alodine 00 shells alloy to
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Antenna diagram showing configuration and lengths when assembled 7 8 16 9 16 9 Description The Pacific Antenna lightweight dual band dipole kit provides
More informationJewelry Basics 101. Basic Wire Loops For best results, use both chain-nose and round-nose pliers. Method 2 Bend then cut. Method 1 Cut then bend
Jewelry Basics 101 #68-007-01 Basic Wire Loops For best results, use both chain-nose and round-nose pliers. Method 2 Bend then cut Use non-serrated chain-nose pliers to bend the wire just above the bead.
More informationAssembly Instructions Beta Prusa Standard & Deluxe
13/11/12 Assembly Instructions Beta Prusa Standard & Deluxe 3D Printer Version 1.0 Date 13/11/12 Page 1 / 66 General data about the assembly instructions for an incomplete machine according to appendix
More informationSSRLS-3 / SSRLU-3 Installation Instructions
5mm Hex Nut Upper Telescoping hannel & Screws Packing List QTY. ITM 1 Top Telescoping hannel 1 ottom Telescoping hannel w/ self drilling screw 15" 18" 1 Top and ottom Rod with connecting arm 25-½ 2 ¼ -
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationAmphenol RF- BNC Connector Series
Page 1 of 7 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC
More informationQUALITY MANAGEMENT SYSTEM
Not controlled in hard copy Rev. 1.0 Date: Page 1 of 18 Subject The following instructions provide a step-by-step procedure to replace the heating element for DEF/SCR/UREA/ADBLUE/DIESEL After Treatment
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationAssembling Instruction. S418 PV Connector M16 Cable Mount
Assembling Instruction S418 PV Connector M16 Cable Mount Electrical Rating: 1000V DC 30A Max. Operation Temperature Range: -40~+90 degree C Caution: 1. Connectors are to be used only to interconnect firmly
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationSUPERSEDED. NOT the LATEST REVISION
Figure 1 OPTIMATE 2.5mm bayonet ceramic connector kits listed in Figure 1 are designed to be applied to fiber optic cable. Coupling Receptacle Kit 501381 1 is used to mate two bayonet connectors in free
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More information* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service
*24017501* 24017501 Coneled Vertil Devie for Wood Doors 98/9949WDC Instlltion Instrutions 1-Point Lth (LBL) 2-Point Lth inludes these dditionl prts NOTE: If door does not hve utout for ling inside lok
More informationOCT 15 Rev E
ORIGINAL INSTRUCTIONS Coaxial Cable Stripper Kits 603995-[ ] Instruction Sheet 408-2766 09 OCT 15 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered
More informationXkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ Rev 1.15 An Optional accessory for the Xkitz XLO-5 or XLO-5DC 5 Channel Color Light Organs Introduction This kit contains all the electronics
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationSYSTIMAX 12A1 Cable Clamp Kit Instructions For Crossply-, R/L-, and LXE-Type Cable
Instruction Sheet 860063510 Issue 4, June 2013 SYSTIMAX Solutions SYSTIMAX 12A1 Cable Clamp Kit Instructions For Crossply-, R/L-, and LXE-Type Cable General The SYSTIMAX 12A1 cable clamp kit is used to
More informationExtraction Tool for Buss Contact
Tooling Akey feature of the Cannon DL connector series is easy contact termination, both in the field and in high-volume production. An ergonomically designed hand crimp tool is available for the low volume
More informationET 51 EXTERIOR ROOF DRIP SIDE FINISH MOULDING INSTALLATION
EXTERIOR ROOF DRIP SIDE FINISH MOULDING 51 INSTALLATION The procedure descried elow is for the LH side. Use the sme procedure for oth the RH nd LH sides, unless otherwise specified. 1. INSTALL ROOF SIDE
More informationCatalog Navigation Guide
atalog Navigation Guide We have configured this online version of our catalog to take advantage of crobat navigation shortcuts (links). However, these links are not visible on the pages making them visible
More informationKit 102 Series Installation Instructions for Wood or Metal Posts on Level Runs
Kit 102 Series Installation Instructions for Wood or Metal Posts on Level Runs A. Drill Posts Hole size for 1/8" or 3/16" cable installation This kit may also be used for stairs or runs that exit the end
More informationF i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1
F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares
More informationEH-20 20m antenna. By VE3RGW
EH-20 20m antenna By VE3RGW Equivalent circuit of EH-20 antenna system. Upper cylinder Lower cylinder Phasing coil Common mode radiator Tune coil RF choke or 14MHz trap 50ohm coaxial cable 0-150pF (case
More informationMiniature Waterproof Shielded Connectors
Miniature Waterproof Shielded Connectors LF Series Mated dimensions 8.9 mm max. ( pos.). Ø Receptacle Plug Short turn bayonet lock Features. Ease of shielded termination and connector assembly All components
More informationAmphenol RF MCX. MCX Connectors MCX. Description. Features/Benefits. Applications
Amphenol RF 20 Connectors Description connectors conform to the European CECC 22000 spec and were introduced in the 1980 s. While the uses identical inner contact and insulator dimensions as the SMB, the
More information75 Ω SSMB Type Connectors
7 Ω SSMB Type Connectors SSMB7 Series FEATURE SSMB7 series are connectors for 7 Ω group of SSMB series ( Ω group). DDK s originally developed 7 Ω group connectors are super mini size push on type. Frequency
More informationSet Part # Rev
Set Part # 21007 Rev-3 06-06-11 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to
More information3 Shielded Compact Ribbon (SCR) Wiremount Plug, XX, and Shell Kit, F200-XXX
3 Shielded Compact Ribbon (SCR) Wiremount Plug, 36110-3000XX, and Shell Kit, 36310-F200-XXX Instructions June 2007 78-9100-4282-5 General This instruction manual explains the method of assembling the 3M
More informationFord Ranger / Bronco II Set Part # Rev B 5-04
Ford Ranger / Bronco II Set Part # 21008 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).
More informationSMB Connectors. RF Coax Connectors. Product Facts
SMB Connectors Product Facts SMB offers snap-fit coupling for quick connect/disconnect Choice of Commercial or High Rel Connectors 50 and 75 Ω MIL-Type connectors available Straight plugs and jacks are
More informationSTEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationELECTRICAL CABLE SPLICE KIT. Roctest Limited, All rights reserved.
INSTRUCTION MANUAL ELECTRICAL CABLE SPLICE KIT Roctest Limited, 2014. All rights reserved. This product should be installed and operated only by qualified personnel. Its misuse is potentially dangerous.
More informationCONCEALED ROD CRASH BAR PR-7085 SERIES EXIT DEVICE ASSEMBLY DETAILS PR mm. 10mm. Lock cylinder. 10mm. Cross bar length (see note #8) Dogging
Floor line TITLE ASSEMLY DETAILS PR-7085 4:02 Hinge stile (inside) Lock stile (inside) Lock stile (outside) Drill 5mm (.20) and tap 1/4-20 (2) Drill 7mm (.266) holes (2) 9mm 12mm See note #6 160mm 9.5mm
More information