A500 ASSEMBLY & INSTALLATION INSTRUCTIONS
|
|
- Eleanor Stephens
- 5 years ago
- Views:
Transcription
1 ASSEMBLY & INSTALLATION INSTRUCTIONS 1
2 CONTENTS 2
3 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety Cable Nut (2) J K Ground Screw Cupped Washer L Supply/Support Cable (2) M Gripper (2) N Countersunk Screws (8) O Wireway Cover Plate (2) P LED Assembly (2) Q Acrylic Rod R O-Ring (4) S Inner Tube Assembly (3) T Outer Tube (3) U Collar (2) V Set Screw (12) W Tube/Acrylic Rod Assembly X Cover Tube (2) 3
4 Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products and options. To Attach to Ceiling (Figures 1 & 2 on following page) CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION. 1. Carefully unpack the fixture from the carton. 2. Mounting plate (B) is shipped installed in canopy (A). Remove caps (C) to separate canopy (A) and mounting plate (B). Retain for use later. 3. Adjust cable lengths to set LED assemblies (P) to a height that will make it easy to reach when installing the tubes. 4. Loosen safety nut on gripper (M). It is not necessary to completely remove. Push supply/support cable (L) into gripper (M) until desired height is reached. Repeat for remaining supply/support cable (L). 5. Fixture is shipped at max height. If a short height is desired, remove the countersunk screws (N) and wireway cover plate (O). Pull supply/support cable (L) up through gripper (M). Coil supply/support cable (L) in compartment, replace wireway cover plate (O) and reinstall countersunk screws (N). (Figure 1) 6. Center mounting plate (B) over the electrical box keeping center slots lined up with threaded holes in electircal box. With a pencil, mark the location of all mounting holes on the ceiling. 7. Put the mounting plate (B) down. Drill 1/4" holes in the locations marked on the ceiling. Place the tapered end of the anchors (F) into the holes and gently tap them flush to the ceiling using a light weight hammer. 8. Thread the wires in the electrical box through the center hole in mounting plate (B) while moving it into position. Using two machine screws (not provided) fasten mounting plate (B) to the electric box. Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture. 9. Using the #10 screws (G), screw mounting plate (B) securely to the ceiling. Be careful not to over-tighten or strip the anchors (F). 10. Raise canopy (A) close to mounting plate (B). Attach safety cables (H) to mounting plate (B) using safety cable nuts (I) to temporarily support canopy (A) while wiring. 11. Using suitable wire connectors (not provided) connect fixture wires to supply wires (white to white, black to black). Attach a pigtail lead to ground screw (J) and cupped washer (K). Connect all ground wires (bare copper or green to bare copper or green). Ground screw (J) and cupped washer (K) are shipped in the mounting kit bag. CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED. 12. Slide canopy (A) over threaded nipple (D) and threaded standoffs (E). Secure canopy (A) with (3) caps (C). CONTINUED 4
5 To Attach to Ceiling (Figures 1 & 2) continued N O D A M K J F B L E I P G H (Figure 1) A M C L (Figure 2) CONTINUED 5
6 To Assembly Tubes (Figures 3 & 4) Q S (Figure 3) 1. Locate acrylic rod (Q) and o-rings (R). Install two o-rings (R) onto each end of acrylic rod (Q). There are grooves in the acrylic rod (Q) for the o-rings (R) to set in. 2. Carefully slide (1) inner tube assembly (S) onto acrylic rod (Q) and roughly center on rod (Q). Slide remaining inner tube assemblies (S) onto acrylic rod, one from each end. U V R 3. Slide a collar (U) onto each end and push up tight to end of inner tube assemblies (S). Make sure tubes are pushed tightly together, but not overlapping. Center everything on acrylic rod (Q), making sure each end has roughly the same amount of rod (Q) exposed. 4. Using hex wrench provided, tighten set screws (V) in both collars (U) evenly. This will secure the inner tube assemblies (S). 5. Slide outer tubes (T) over inner tube assemblies (S). 6. Figure 4 shows completed tube/acrylic rod assembly (W). U T S S T S T U Q (Figure 4) W- TUBE/ACRYLIC ROD ASSEMBLY CONTINUED 6
7 To Complete Installation (Figure 5) CAUTION: THE FOLLOWING STEPS REQUIRE TWO PEOPLE. 1. Slide cover tube (X) over LED assembly (P). Be sure to slide on far enough so that set screws (V) are exposed. 2. Move outer tubes (T) to one end of tube/rod assembly (W) to expose end of acrylic rod (Q). 3. Slide exposed end of acrylic rod (Q) into the LED assembly (P) until it stops. 4. Tighten set screws (V) in LED assembly (P) evenly to secure end of tube/acrylic rod assembly (W). Note: Ensure both supply/support cables (L) are pointing up from LED Assembly (P). 5. Move cover tube (X) up against tube/rod assembly (W) to cover set screws (V). 6. Repeat steps (1 thru 5) for other side of fixture. 7. To Raise Fixture: Loosen safety nut on gripper (M). It is not necessary to completely remove. Push supply/support cable (L) into gripper (M) until desired height is reached. Repeat for remaining supply/support cable (L). 8. To Lower Fixture: Loosen safety nut, push up on gripper (M) and gently pull down on supply/ support cable (L). 9. Retighten safety nuts on grippers (M). 10. Restore electricity at the main breaker. (Figure 5) Safety Nut M L T W V P X If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture! * Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture. 7
A524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A B C Fixture Mounting Bracket Canopy D Threaded Standoffs (2) E Cap (2) F Anchors (4) G #10 Screws (4) H I J K Safety Cable #8 Screw Ground Screw Cupped Washer Socket Assembly (6)
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationCaution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
izz Kitchen Pendant With Brass Accent - 18700 Page 1 of 5 CAUTON: AUR TO NSTA THS XTUR PROPRY MAY RSUT N SROUS PRSONA NURY OR DATH AND PROPRTY DAMAG. We recommend installation by a licensed electrician.
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationPARTS & ASSEMBLY SHEET
PARTS & ASSEMBLY SHEET Fixture Name: Echelon 8981-3P BRI / GRM This fixture assembled PO: Date: Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationPARTS & ASSEMBLY SHEET
PARTS & ASSEMBLY SHEET Fixture Name: Echelon 8981-9 BRI / GRM This fixture assembled PO: Date: Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D
ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationInstallation Instructions
Installation Instructions Optima LED 8 Double-Sided StretchLite Perimeter Lit Graphic Display Line Voltage Connector Optima LED DS5 (Double-sided StretchLite Graphic Display) with Graphics Corner Bracket
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More information1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS 1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationINSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011
INSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011 Specifications: Installs to K-Series desk or wall mount. Accommodates K-Series mounting arms (fixed
More informationMenu Board Tilt or Fixed Mount Installation Instructions MDS1T-200, MDS1T-300, MDS1T-400 MDS2T-200, MDS2T-300, MDS2T-400 MDS3T-200, MDS3T-300, MDS3T-400 MDS4T-200, MDS4T-300, MDS4T-400 MDS5T-200, MDS5T-300,
More informationAssembly Instructions for Model: VMPR1
Assembly Instructions for Model: VMPR1 Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LC/LP
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges
More informationGLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR
GLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials,
More informationJ-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY
KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE
More informationInstalling CNC Stepper Motor Mounts On A Sherline Lathe
Installing CNC Stepper Motor Mounts On A Sherline Lathe P/N 6720 (6725 Metric) 4000/4100/4500/4600 Lathes P/N 6730 (6735 Metric) 4400/4410 Lathe USING THE TEMPLATE BLOCKS TO LOCATE NEW MOUNTING HOLES FOR
More informationInstruction page index: Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF. Page 1 of 5. Center Feed installation Side Feed installation
Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF Page 1 of 5 Instruction page index: Center Feed installation Side Feed installation 2-3 4-5 Kilo S - Instruction for center feed installation
More informationLTS. FLIRT CHANDELIER INSTALLATION INSTRUCTIONS
R 5-05 5LTS. FLIRT CHNDELIER INSTLLTION INSTRUCTIONS L I G H T I N G WRNING DISCONNECT POWER EFORE RE-LMPING OR WIRING THE FIXTURE RED LL INSTRUCTIONS COMPLETELY EFORE STRTING INSTLLTION. CUTION TO VOID
More informationREAD BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION
edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationInstallation Instructions
edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung
More informationBluetooth DRO Installation for Bench Mills
The premier source of tooling, parts, and accessories for bench top machinists. Bluetooth DRO Installation for Bench Mills These instructions describe how to install the following products: 5494: Digital
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel. Pleasegotowww.quoizel.forproductcleaningtips.GototheCare+Maintenance selection. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationClearSpan Hydroponic Table Kit
ClearSpan Hydroponic Table Kit Hydroponic Table Kit (The 109314 (4' x 16') model is shown.) Designed to grow healthy plants without soil using mineral-nutrient solutions. 2009 ClearSpan All Rights Reserved.
More informationINSTALLATION INSTRUCTIONS
STRIP DOORS AIR DOORS INSTALLATION INSTRUCTIONS BULK PVC FILM STRIP SHEET PANEL SCREENS, CURTAINS and ENCLOSURES MEGA-PRO SWINGING DOORS DOCK ACCESSORIES IMPORTANT Carefully examine the carton(s) for damage.
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationSignature Choral Riser Side Rail
Assembly/Owner s Manual Signature Choral Riser Side Rail Signature Choral 3-Step Riser with Optional Side Rail Signature Choral 4-Step Riser with Optional Side Rail CONTENTS Visit the Signature Choral
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationFully Demountable Torch Installation Instructions (Axial Version)
Fully Demountable Torch Installation Instructions (Axial Version) Introduction Applications This instruction sheet covers the installation of the fully demountable torch for axial ICP-OES instruments (Vista-PRO,
More informationAssembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationLC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More informationOriginal Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
More informationFIXED PANEL SLIDER QCI5241
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationFabric tiered drum pendant 30in Assembly and Installation Instructions
CAUTION: Fabric tiered drum pendant 30in Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More information* ** * * VIEW "A" VIEW "B" INSTALLATION INSTRUCTIONS
5105362000 ASSEMBLIES 1 2 WHICH IS CONTRARY TO THE CONTAINED HEREIN. IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE OF IT, P/C PG. OF GENERAL NOTES: 1. For all aircraft cable assemblies except
More informationConnect each sections electricity cables with a connections block or splices and heatshrink. Proceed to Myla installation manual.
MYLA L & XL ASSEMBLY 1. 2. PARTS 3-5 SECTIONS Prepare a soft clean workspace to assemble the light fixture. Carefully unpack the light fixture and other contents. Myla L consists of 3 separate sections
More informationUniversal Projector Ceiling Mount Model: DPM-45
Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationINSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY
NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationSingle Sided Height Adjustable Benching
Single Sided Height Adjustable Benching Bit Holder Power Drill Long # Square Drive Bit 5mm Hex Drive Bit T-30 Torx Drive Bit Hex Key -.5mm (Provided) SERIES 5 Hex Key - 3mm Socket Adaptor (or) If you have
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationPAM-200 Universal Projector Mount
INSTALLATION MANUAL PAM-200 Universal Projector Mount Sony Electronics 16540 West Bernardo Drive San Diego, CA 92127 www.sony.com IN-PAM200.R0 Table of Contents Parts List...- 3 - Installation Tools...-
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationSpiderbeam Balun Construction Guide
BALUN CONSTRUCTION GUIDE Ver. 1.0 1 The components of the Balun Kit are in a plastic bag. Most of the components are inside the plastic case of the balun. The aluminum U-profile and the RG-142 Teflon Coax
More informationProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath
More informationGroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property.
GroundControl TM use supplied hardware Use only hardware supplied in your GroundControl kit or supplied by an authorized YAKIMA dealer. Use of unauthorized parts in the GroundControl system could result
More informationFIXED SHOWER SCREEN For Wall Mount Hinges QCI5283
FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationAndyMark DART 12.
AndyMark DART 12 Part Number Description QTY These Parts Are Pre-Assembled by AndyMark am-0031 Bearing, 3/16"ID (R3) 1 am-0209 Bearing, 3/8"ID 1614ZZ 2 am-1028 Screw, #10-32x3/8 Pan Head Philips 8 am-1121
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationGiraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationInstall Instructions. NewAge Steel Welded Tall Locker
Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More information340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2016. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationMALEKO WALL-MOUNT FAUCET INSTALLATION
SKU(s): 934146 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the
More informationSpring Loaded All Season Roll-Up Doors
Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationMounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome
VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:
More informationFrameless Inline Door QCI5250
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationModel: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95
Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 6 16 9 16 9 8 6 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationF5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS WARNING
F5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS TROY LIGHTING DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More information