Power Connectors for Industrial and Commercial Applications

Transcription

1 Table of Contents AMP, AMPINNERGY, AMPOWER, AMP-O-LECTRIC, AMP-TAPETRONIC, DIAMOND GRIP, ELCON, RAYCHEM, SOLISTRAND, and TYCO are trademarks. AMP Power Series Connectors Selection Guide and Overview 3,4 Series 15/30/45 (Single-Pole) 5 Series 50 (2-Pole Battery) 6 Series 50 Finger Probe Resistant (FPR) 7 Series 75 (Single-Pole) 8 Series 120 (Single-Pole) 9 Series 120 (2-Pole Battery) 10 Series 175 (2-Pole Battery) 11 Series 180 (Single-Pole) 12 Series 350 (2-Pole Battery) 13 Accessories 14,15 Application Tooling 16,17 AMPINNERGY Connectors Wire-To-Wire Introduction and Technical Documents 18 1-Pole Housing and Accessories 19 Contacts and Application Tooling 20 Wire-To-Board Introduction and Technical Documents 21 PC Board Receptacles 22,23 Plug Housings (2- to 8-Position) 24 Contacts and Application Tooling 25 Technical Documents 26 Part Number Index 27 Related Product Catalogs 28,29 Engineering Notes 30 Global Contacts 31 PICO is a trademark of Pacific Industrial Components Corporation. Other products, logos, and company names mentioned herein may be trademarks of their respective owners by Tyco Electronics Corporation. All Rights Reserved. 2 While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this catalog, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult Tyco Electronics for the latest dimensions and design specifications.

2 AMP Power Series Connectors Product Facts Single-pole and 2-pole (battery) quick connect/disconnect connectors Eight Series, based on approximate currentcarrying capability: Series 15/30/45 (Single-Pole) Series 50 (2-Pole Battery) Series 50 Finger Probe Resistant (FPR) Series 75 (Single-Pole) Series 120 (Single- and 2-Pole) Series 175 (2-Pole Battery) Series 180 (Single-Pole) Series 350 (2-Pole Battery) Voltage rating: 600 V AC/DC Color-coded housings, UL 94V-0 Hermaphroditic (genderless) housings reduce inventory Modular, single-pole housings are stackable in four directions Polarity (+ and -) molded into 2-pole housings promotes proper wiring Mechanical keys help prevent two different colorcoded housings from mating Stainless steel retaining springs secure contacts in housings Stamped and formed, open barrel contacts (6-20 AWG) on reels for automatic and semiautomatic machine termination Loose piece, cold-headed contacts (6 AWG 300 MCM) for manual and hydraulic hand tools; reducing bushings accommodate smaller wire sizes Compatible with industry standard crimp tooling from PICO Corporation ( Connectors intermateable with similar connectors from other manufacturers Series 15/30/45, single-pole connectors designed to meet Amateur Radio Emergency Service (ARES)/Radio Amateur Civil Emergency Service (RACES) Standard Power Connector requirements Accessories available for mounting, vibration protection, and strain relief Component Recognized by Underwriters Laboratories Inc. to US and Canadian Standards, File No. E28476 C US AMP Power Series Connectors provide a durable, quick connect/disconnect means to transmit "power" levels of current and voltage ( A, 600 V AC/DC). This product family is primarily comprised of single-pole and 2-pole (battery) connector housings, crimp snap-in contacts, and accessories. Housings are offered in various colors. Two-pole housings have different polarization configurations; with the exception of black housings, each color identifies a different keying configuration. In general, only like color housings will mate. Contacts are either cold-headed or stamped and formed, depending upon the connector Series. AMP Power Series Connectors are divided into eight Series, based on approximate current-carrying capability. Applications AC/DC Power Supplies and Charging Systems, Rechargeable Batteries, Material Handling Equipment (e.g. forklift trucks), Electric Vehicles (e.g., golf carts, sweepers, wheelchairs), Office Furniture/Panels, Amateur Emergency Radios, and Industrial Equipment Technical Documents See page 26 3

3 4 AMP Power Series Connectors (Continued) AMP Power Series 15/30/45 Single-pole connector housings are stackable side-to-side and top-to-bottom. For example, Series 30 red and black housings joined side-to-side, are commonly used as standard power connectors for handheld, mobile, or base amateur radio equipment. Modular housings can also be grouped into plug frames with or without latches, which mate with receptacle housings. Typically, these are used as quick disconnects for electrical power distribution in office furniture and panels. AMP Power Series 50 Two-pole (battery) housings are available in bulk quantities or in kit form (i.e., 1 housing and 2 contacts). These high durability connectors are designed for repeated mating and unmating. AMP Power Series 75 Single-pole, stackable housings, in locking and non-locking versions, are available in a variety of colors. Housings accept stamped and formed or cold-headed contacts. Bulk quantities and connector kits (1 housing and 1 contact) can be ordered. Accessories include: mounting wings for through-panel or surface mounting and mounting clamp sets for ganging housings. Selection Guide AMP Power Series 50 Finger Probe Resistant (FPR) This new, 2-pole, FPR version helps prevent finger access, which allows it to be more safely used at elevated voltages and in user access areas. AMP Power Series 120 This Series includes both singleand 2-pole (battery) versions. Single-pole housings with molded-in dovetails allow stacking. Housing retaining pins provide more vibration protection. Two-pole housing have slots designed to accept mounting clamp sets for easier panel mounting. AMP Power Series 175 Two-pole (battery) housings accept coldheaded contacts (4-1/0 AWG). Basically, these connectors offer the same features as the two-pole Series 50 connectors. AMP Power Series 180 Stamped & Housing Stackable Current Voltage, Max. Cold-headed Housing Series Formed Contact Approvals Type Housing Max. (A) (V, AC or DC) Contact (AWG) Colors (AWG) 15 Single-Pole Yes Blue, Black, White, Red C US Green, Yellow, Orange, Gray File No. E Single-Pole Yes Blue, Black, White, Red C US Green, Yellow, Orange, Gray File No. E Single-Pole Yes 40* Blue, Black, White, Red C US Green, Yellow, Orange, Gray File No. E Pole No , 8, ,10-12 Red, Gray, Blue, Black, C US Yellow File No. E Single-Pole Yes , 8, ,10-12 Blue, Black, White, Green, C US Red (Single-Pole) File No. E Single-Pole Yes , 4, 6 Blue, Black, White, Green, C US Red (Single-Pole) File No. E Pole No , 4, 6 Blue, Gray (2-Pole) C US File No. E Pole No /0, 1, 2, 4 Blue, Gray, Orange, Yellow, Red 180 Single-Pole Yes /0, 1, 2, 4 Blue, Black, White, Green, Red Pole No 275** 600 1/0, 2/0, 3/0, Blue, Green, Red, Yellow, 4/0, 300 MCM Orange, Gray *Performance equivalent to competition **Tested to 275 amps with 4/0 AWG wire These stackable, single-pole connectors accept cold-headed contacts (4-1/0 AWG). Most features are similar to the smaller, single-pole, Series 120 connectors. AMP Power Series 350 Rugged, 2-pole housings accept only loose piece, cold-headed contacts (1/0 300 MCM). Rated at 275 A, these connectors have been tested up to 275 A, with 4/0 AWG wire. C C C US US US File No. E28476 File No. E28476 File No. E28476

4 Product Facts Color-coded UL 94V-0 housings: blue, black, white, green, red, yellow, orange and gray Genderless housings reduce inventory 3 contact offerings available: Series 15, 30 and 45 Built-in interlocking features (dovetails) allow stacking Series 15/30/45, single-pole connectors designed to meet Amateur Radio Emergency Service (ARES)/Radio Amateur Civil Emergency Service (RACES) Standard Power Connector requirements Plug frames (with or without latches) and receptacle housings accept stacked single-pole housings (2 to 8 poles) File No. E28476 C Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver or tin plating Mounting Wings & Spacers Polycarbonate, UL 94V-0 Retaining Pins Stainless steel Electrical Characteristics Current Carrying Capability 40 A w/10 AWG wire (Series 45) 30 A w/12 AWG wire (Series 30) 20 A w/16 AWG wire (Series 15) Operating Voltage 600 V, AC or DC Dielectric Withstanding Voltage 2200 VDC Average Initial Contact Resistance 525 micro-ohms Mechanical Characteristics Contact Retention 25 lbs. [111.2 N] Average Mating/Unmating Force 4.7 [20.9 N] Max. Wire Insulation Diameter 175 [18.16] Wire Size Range AWG [5-0.5 mm 2 ] Related Product Data Accessories page 14 US Power Connectors for AMP Power Series 15/30/45 Connectors (Single-Pole) Single-Pole Housing.311 [7.9].311 [7.9] AMP Power Series [7.9].968 [24.6].331 [8.4] Stamped and Formed Contact (Strip).141 ± 004 [ 3.58 ± 0.1] Closed Barrel Contact (Loose Piece) Housing 1 Contact Part Number Color Part Number Strip Form (16, 18, 20 AWG) Loose Piece (16-20 AWG) Blue Black White Green (silver) 2 Red (tin) Yellow Orange Gray AMP Power Series 30 Housing 1 Contact Part Number Color Part Number Strip Form (12, 14, 16 AWG) Loose Piece (12-16 AWG) Blue Black White Green (silver) Dimensions Red (tin) 3 shown above. Yellow Orange Gray AMP Power Series [3.81] Housing 1 Contact Part Number Color Part Number Strip Form (10, 12, 14 AWG) Blue Black White Green (silver) 4 Red (tin) 4 Yellow Orange Gray Housings are bulk packaged. 3 Use Applicator Part No Use Applicator Part No Use Applicator Part No [6.99].630 [16.00] Note: Tyco Electronics does NOT recommend intermating connectors with different contact platings..290 [7.36].152 [3.86] Dia. 5

5 AMP Power Series 50 Connectors (2-Pole Battery) Product Facts Color-coded UL 94V-0 housings: gray, red, blue, yellow and black; other colors available upon request Note: Black color housing has the same mechanical key as the gray housing Mechanical keys help prevent two different voltage color- coded housings from mating Polarity (+ and -) molded into housings Genderless housings reduce inventory Cold-headed contact wire range: 6, 8, AWG (Taped version of the cold-headed contacts available.) File No. E28476 C Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating Electrical Characteristics Current Carrying Capability 50 amp per circuit w/6 AWG wire Max. Operating Voltage 600 V, AC or DC Dielectric Withstanding Voltage 2200 VDC Average Initial Contact Resistance 200 micro-ohms Mechanical Characteristics Contact Retention 50 lbs. [222.4 N] Average Mating/Unmating Force 15 lbs. [66.7 N] Max. Wire Insulation Diameter.44 [11.18] Wire Size Range 6-12 AWG (also 6-16 AWG w/reducing Bushings) Related Product Data Accessories page 14 US 2-Pole Housing 1.38 [35.05] 1.90 [48.23].625 [15.88] Cold-headed Contact.323 [8.2] Series 50 (2-Pole) Housing 2,3 Contact 2 Connector Kit Color Part Number Wire Size Part Number Part Number 1 Red AWG AWG Gray AWG AWG Blue AWG AWG Black AWG AWG Yellow AWG AWG Cold-headed Contact 8 AWG Stamped and Formed contacts, on Reel 6-8 AWG strip (tin) 8 6Stamped and Formed contacts, on Reel AWG (strip) 8 6 AWG Taped version of Cold-headed contacts 8 AWG AWG Housing and 2 contacts. 2 Housings and contacts are bulk packaged. 3 Mechanical keys molded in housings will engage only with housings of same color. 4 Black color housing has the same mechanical key as the gray housing. 5 Use Heavy Duty Mini-Applicator (HDM) for 6 to 8 AWG - Part Number (Use with AMP-O-LECTRIC Model K Terminator) 6 Use Heavy Duty Mini-Applicator (HDM) for 10 to 12 AWG - Part Number (Use with AMP-O-LECTRIC Model K Terminator) 7 Hand Tool for Cold-headed Contact - Part Number Taped version can be terminated using the AMP-TAPETRONIC Machine 8 Use Power Lock Machine Part Number Voltage Key Color Chart Housing Color Voltage Yellow 12V Red 24V Gray 36V Blue 48V Black 80V Color code given for various voltages is only a suggestion, other codes and keys available upon request. *.290 [7.37] Ref [31.2].50 [12.7] *Inside Diameter 6 AWG.222 [5.64] 8 AWG.187 [4.75] AWG.150 [3.81] Stamped and Formed Contact (on Reel) 1.28 [32.64] 6

6 AMP Power Series 50 FPR (Finger Probe Resistant) Connectors Product Facts Complies with UL finger probe requirements Utilizes AMP Power Series 50 contacts Brown and white housing colors available (other colors possible) Two keying configurations available (up to 6 keying configurations possible) 2-Pole Housing.323 [8.2] * Cold-headed Contact.290 [7.37] Ref [31.2].50 [12.7] *Inside Diameter 6 AWG.222 [5.64] 8 AWG.187 [4.75] AWG.150 [3.81] File No. E28476 C US Stamped and Formed Contact (on Reel).672 [17.08] 1.28 [32.64] Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper Reducing Bushings Copper with silver plating Electrical Characteristics Current Capability 50 A max. Voltage Rating 600 V, AC or DC Dielectric Withstanding Voltage 2200 VDC Mechanical Characteristics Designed to defeat UL finger probe as outlined in UL Contact Retention 50 lbs. [222.4 N] Wire Size 6-12 AWG [15-3 mm 2 ] Max. Wire Insulation Diameter.44 [11.18] Series 50 FPR (2-Pole) Contact Part Number Housing 1,2 1 Wire Size Cold-headed 5 Stamped and Formed/Strip 3,4,6 Color Part Number Loose Piece On Tape On Reel 6 AWG Brown AWG (tin) 8 AWG White AWG AWG Housings and contacts are bulk packaged. 2 Mechanical keys molded in housings will engage only with housings of same color. 3 Use Heavy Duty Mini-Applicator (HDM) for 6 to 8 AWG - Part Number (Use with AMP-O-LECTRIC Model K Terminator) 4 Use Heavy Duty Mini-Applicator (HDM) for 10 to 12 AWG - Part Number (Use with AMP-O-LECTRIC Model K Terminator) 5 Hand Tool for Cold-headed Contact - Part Number Taped version can be terminated using the AMP-TAPETRONIC Machine 6 Use Power Lock Machine Part Number Related Product Data Accessories page 14 Applications Uninterruptible Power Supplies Power Supplies Battery Banks 7

7 AMP Power Series 75 Connectors (Single-Pole) Product Facts Color-coded UL 94V-0 housings: blue, black, white, green and red Genderless housings reduce inventory Cold-headed contact wire range: 6, 8, AWG Stamped and formed contacts available: 6-8 AWG Part Number (strip); AWG Part Number (strip) File No. E28476 C US Housing without Locking Feature Contact Cold-headed Contact.50 [12.7] 1.23 [31.2] Housing/Spring Subassembly.290 [7.37] Ref. Housing with Locking Feature Contact Housing/Spring Subassembly Stamped and Formed Contact (on Reel) 1.28 [32.64] Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating Mounting Wings Polycarbonate, UL 94V-0 Retaining Pins Stainless steel Electrical Characteristics Current Carrying Capability (with 6 AWG) Configuration: Single-Pole 75 A 1x2 Stacked 62 A 2x2 Stacked 60 A 1x3 Stacked 58 A 2x3 Stacked 52 A Operating Voltage 600 V, AC or DC Dielectric Withstanding Voltage 2200 VDC Average Initial Contact Resistance 200 micro-ohms Mechanical Characteristics Contact Retention 50 lbs. [222.4 N] Average Mating/Unmating Force 15 lbs. [66.7 N] Max. Wire Insulation Diameter.44 [11.18] Wire Size Range 6-12 AWG [15-3 mm 2 ] Related Product Data Accessories page 14 Application Tooling page [8.2] * *Inside Diameter 6 AWG.222 [5.64] 8 AWG.187 [4.75] AWG.150 [3.81] Series 75 (Single-Pole) Housing 2 Cold-headed Contact 2 Connector Kit Color Part Number Wire Size Part Number Part Number 1 Non-Locking Version Blue AWG Black AWG White AWG Green AWG Red AWG Locking Version Blue AWG Black AWG White AWG Green AWG Red AWG *Samples available on loose housing and contacts only. Contacts Description Wire Size Part Number Applicator Part No. Die Set for AMP-O-LECTRIC Part Number 3 Model K Terminator Cold-headed 6 AWG (Loose Piece) 4 8 AWG AWG Cold-headed 6 AWG (Tape) 3, 4 8 AWG AWG Stamped and Formed 6-8 AWG (Strip) AWG housing and 1 contact 2 Housings and contacts are bulk packaged. 3 Taped version can be terminated using the AMP-TAPETRONIC machine Part Number Use hand tool Part Number for Cold-headed contacts 8

8 AMP Power Series 120 Connectors (Single-Pole) Single-Pole Housing Cold-headed Contact [26.89].415 [10.5] Product Facts Color-coded modular housings: blue, black, white, green and red Genderless housings reduce inventory Cold-headed contact wire range: 2, 4, and 6 AWG Built-in interlocking features (dovetails) allow stacking and wire routing Self-wiping contacts increase product life and improve conductivity Integral stainless steel locking spring in housing for contact retention Rugged design File No. E28476 C Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating Mounting Clamp Sets Aluminum US.883 [22.42].094 [2.4] Series 120 (Single-Pole).883 [22.42] [69.74].480 [12.2] *.921 [23.4] 1.99 [50.5] *Inside Diameter 6 AWG.222 [5.64]; 4 AWG.295 [7.5]; 2 AWG.344 [8.74] Housing Contact Connector Kit Color Part Number Wire Size Part Number Part Number 1 Blue AWG Black AWG White AWG Green AWG Red AWG AWG AWG Housing and 1 contact. Electrical Characteristics Current Carrying Capability Single-Pole 120 A 2x1 Stacked Array 115 A 2x2 Stacked Array 115 A Voltage Rating 600 V (both AC and DC) Dielectric Withstanding Voltage 2200 VDC Average Initial Contact Resistance 136 micro-ohms Related Product Data Accessories page 15 Application Tooling page 16 Technical Documents page 26 Mechanical Characteristics Contact Retention 100 lbs. [444.8 N] Average Mating/Unmating Force 8 lbs. [35.6 N] Temperature Rating -4 F to 221 F [-20 C to 105 C] Max. Wire Insulation Diameter.6 [15.24] Wire Size Range 2-6 AWG 9

9 AMP Power Series 120 Connectors (2-Pole Battery) 2-Pole Housing Cold-headed Contact 1.74 [44.31].415 [10.5] Product Facts Color-coded UL 94V-0 housings: gray and blue Keying feature helps prevent two different voltage color-coded housings from mating Genderless housings reduce inventory Contact wire range: 2, 4, 6 and 8 AWG Molded-in panel mount grooves Integral stainless steel locking spring in housing for contact retention Rugged design File No. E28476 C Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating US Panel Mount Grooves 2 Plc. Series 120 (2-Pole) 2.50 [63.45].811 [20.6].480 [12.2] *.921 [23.4] 1.99 [50.5] *Inside Diameter 6 AWG.222 [5.64]; 4 AWG.295 [7.5]; 2 AWG.344 [8.74] Housing 2,3 Contact 2 Connector Kit Color Part Number Wire Size Part Number Part Number 1 Gray AWG Blue AWG Gray AWG Blue AWG Gray AWG Blue AWG Housing and 2 contacts. 2 Housings and contacts are bulk packaged. 3 Mechanical keys molded in connectors will engage only with connectors of same color. Electrical Characteristics Current Carrying Capability 115 A with 2 AWG Voltage Rating 600 V (both AC and DC) Dielectric Withstanding Voltage 2200 VDC Avg. Initial Contact Resistance 136 micro-ohms Voltage Key Color Chart Housing 2,3 Color Gray Blue Voltage 36 V 48 V Color code given for various voltages is only a suggestion, other codes and keys available upon request. Mechanical Characteristics Contact Retention 100 lbs. [444.8 N] Average Mating/Unmating Force 18 lbs. [80.1 N] Temperature Rating -4 F to 221 F [-20 C to 105 C] Max. Wire Insulation Diameter.6 [15.24] Wire Size Range 2-8 AWG 10 Related Product Data Accessories page 15 Application Tooling page 16 Technical Documents page 26

10 AMP Power Series 175 Connectors (2-Pole Battery) Product Facts Color-coded UL 94V-0 housings: yellow, orange, red, gray, blue, and black Keying feature helps prevent two different voltage color-coded housings from mating Genderless housings reduce inventory Contact wire range: 1/0, 1, 2, 4 AWG Integral stainless steel locking spring in housing for contact retention Reducing bushings down to 10 gauge 2-Pole Housing 2.11 [53.5] 3.08 [78.2] 1.0 [25.4] Cold-headed Contact TYCO 2.35±.03 [59.8±0.8].5±.016 [12.7±0.4] Dia. Inside Diameter.516±.005 [13.1±0.13] for 1/0 AWG.512±.005 [13.0±0.13] for 1 AWG, 2 AWG, and 4 AWG File No. E28476 C US Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating Electrical Characteristics Current Carrying Capability F [26.9 C] T-Rise with 1/0 AWG wire Voltage Rating 600 V (both AC and DC) Dielectric Withstanding Voltage 2200 VDC Avg. Initial Contact Resistance 100 micro-ohms Mechanical Characteristics Average Mating/Unmating Force 25 lbs. [ N] Max. Wire Insulation Diameter.750 [19.05] Wire Size Range 1/0, 1, 2, 4 AWG [53, 40, 35, 21 mm 2 ] Contact Retention 300 lbs. [1, N] Temperature Rating -4 F to 221 F [-20 C to 105 C] Related Product Data Accessories page 15 Application Tooling page 16 Technical Documents page 26 Series 175 (2-Pole) Housing Connector Kit Part Numbers 1, 2 Color Part Number 4 AWG 2 AWG 1 AWG 1/0 AWG Yellow Orange Red Gray Blue Black Housing and 2 contacts. 2 Housings and contacts are bulk packaged. 3 Black housing mates with any other housing. Contacts (Cold-headed) Wire Size Part Number 4 AWG AWG AWG /0 AWG Voltage Key Color Chart Housing Color Yellow Orange Red Gray Blue Black Voltage 12 V 18 V 24 V 36 V 48 V 80 V Color code given for various voltages is only a suggestion, other codes and keys available upon request. 11

11 AMP Power Series 180 Connectors (Single-Pole) Product Facts Color-coded modular housings: blue, black, white, red and green Genderless housings reduce inventory Contact wire range: 1/0, 1, 2, 4 AWG Integral stainless steel locking spring in housing for contact retention Built-in interlocking features (dovetails) allow stacking and wire routing Reducing bushings down to 10 gauge Single-Pole Housing 1.07 [27.2] 3.25 [82.6].93 [23.5] 1.01 [25.6] Cold-headed Contact TYCO 2.35±.03 [59.8±0.8].5±.016 [12.7±0.4] Dia. Inside Diameter.516±.005 [13.1±0.13] for 1/0 AWG.512±.005 [13.0±0.13] for 1 AWG, 2 AWG, and 4 AWG File No. E28476 C US Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Mounting Clamp Sets Aluminum Reducing Bushings Copper with silver plating Electrical Characteristics Current Carrying Capability (1/0 AWG Wire) 1 x A, 84.9 F [29.4 C] T-Rise 2 x A, 78.3 F [25.7 C] T-Rise 2 x A, 76.6 F [24.8 C] T-Rise Voltage Rating 600 V (both AC and DC) Dielectric Withstanding Voltage 2200 VDC Avg. Initial Contact Resistance 100 micro-ohms Series 180 (Single-Pole) Housing Connector Kit Part Numbers 1,2 Color Part Number 4 AWG 2 AWG 1 AWG 1/0 AWG Blue Black White Red Green Housing and 1 contact. 2 Housings and contacts are bulk packaged. Contacts (Cold-headed) Wire Size Part Number 4 AWG AWG AWG /0 AWG Mechanical Characteristics Average Mating/Unmating Force 20 lb. [89 N] Max. Wire Insulation Diameter.900 [22.86] Wire Size Range 1/0, 1, 2, 4 AWG [53, 40, 35, 21 mm 2 ] Contact Retention 170 lb. [756 N] Temperature Rating -4 F to 221 F [-20 C to 105 C] Related Product Data Accessories page 15 Application Tooling page 16 Technical Documents page 26

12 AMP Power Series 350 Connectors (2-Pole Battery) Product Facts Color-coded UL 94V-0 housings: yellow, orange, red, gray, blue, and green Keying feature helps prevent two different voltage color-coded housings from mating Genderless housings reduce inventory Contact wire range: 1/0, 2/0, 3/0, 4/0, 300 MCM Replaceable contacts Integral stainless steel locking spring in housing for contact retention File No. E28476 C Material and Finish Housing Polycarbonate, UL 94V-0 Retaining Spring Stainless Steel Contacts Copper with silver plating Reducing Bushings Copper with silver plating Electrical Characteristics Current Carrying Capability F [28.5 C] T-Rise with 4/0 AWG wire Voltage Rating 600 V, AC or DC Dielectric Withstanding Voltage 2200 VDC Average Initial Contact Resistance 50 micro-ohms Mechanical Characteristics Contact Retention 500 lbs. [ N] Average Mating/Unmating Force 30 lbs. [133.5 N] Max. Wire Insulation Diameter 1.10 [27.94] Temperature Rating -4 F to 221 F [-20 C to 105 C] Wire Size Range 1/0, 2/0, 3/0, 4/0, 300 MCM [53, 67, 85, 107, 152 mm 2 ] Related Product Data Accessories page 15 Application Tooling page 16 Technical Documents page 26 Reducing Bushing (1/0 to 2/0 AWG) Part No Cable Clamp Part No US 2-Pole Housing 1.38 [35.0].256 Dia. [6.5] 2 holes 1.14 [29.0] 4.23 [107.46] Series 350 (2-Pole) 1.31 [33.2] Cold-headed Contact *Inside Diameter.437±0.004 [ /- 0.10] for 1/0 AWG.488±0.004 [ /- 0.10] for 2/0 AWG.579±0.004 [ /- 0.10] for 3/0 AWG.642±0.004 [ /- 0.10] for 4/0 AWG.752±0.004 [ /- 0.10] for 300 MCM Note: 300 MCM contact dimensions shown, unless otherwise noted. Housing Connector Kit Part Numbers 1,2 Color Part Number 1/0 AWG 2/0 AWG 3/0 AWG 4/0 AWG 300 MCM Yellow Orange Red Gray Blue Green Housing and 2 contacts. 2 Housings and contacts are bulk packaged..811±.016 [20.6±0.4] 3.083±.004 [78.3±1.0] 1.299±.02 [33.0±0.5] Contacts (Cold-headed) Wire Size Part Number 1/0 AWG /0 AWG /0 AWG /0 AWG MCM Voltage Key Color Chart Housing Color Yellow Orange Red Gray Blue Green Voltage 12V 18V 24V 36V 48V 72V Color code given for various voltages is only a suggestion, other codes and keys available upon request. *.961 [24.4] Dia. 13

13 AMP Power Series Accessories Series 15/30/45 Hardware Kits Series 15/30/45 Accessories Part Number Description Mounting Wings Red, UL 94V-0 Spacers Red, UL 94V-0, Short Red, UL 94V-0, Long Retaining Pins for use with 15 A/30 A/45 A [6.35] length [11.18] length [21.6] length Part Number Description Plug and Receptacle Housings Receptacle, 2, 3, 4 pole Receptacle, 5, 6 pole Receptacle, 7, 8 pole Plug Frame without Latch, 2, 3, 4 pole Plug Frame without Latch, 5, 6 pole Plug Frame without Latch, 7, 8 pole Plug Frame with Latch, 2, 3, 4 pole Plug Frame with Latch, 5, 6 pole Plug Frame with Latch, 7, 8 pole Series 15/30/45 Mounting Wings Part Number Description Hardware Kits (Cable clamp, screws & retaining pins) pole pole pole Series 50 Accessories Part Number Description Plastic Handle & Screw Kit, Red Dust Cover, Black Strain Relief Cable Clamp Kit, #6 & #8 AWG Strain Relief Cable Clamp Kit, #10 & #12 AWG Strain Relief Cable Clamp Kit, Single Conductor #6 Please contact Product Engineering or Product Management for availability. Reducing Bushings Wire Size (AWG) Part Number 6 to to to (permits use of smaller wires with 6 AWG contact Part Number ) Series 75 Accessories Part Number Description Mounting Wings Blue, oval mounting hole Blue, round mounting hole Retaining Pins for use with 75 A/120 A/180 A A/120 A/180 A hsgs, 1 high block A/120 A/180 A hsgs, 2 high block A/120 A/180 A hsgs, 3 high block Reducing Bushings for Series 50 A and 75 A to 8 AWG to AWG to AWG Mounting clamp set part numbers available. 14

14 AMP Power Series Accessories (Continued) Series 120 Panel Mounting Clamp Series 120 Accessories Part Number Type Description Retaining Pins for use with 75A/120A/180A Single-Pole 1 high block Single-Pole 2 high block Reducing Bushings Single/2-Pole 2 to 4 AWG Single/2-Pole 2 to 6 AWG Single/2-Pole 2 to 8 AWG Mounting Clamp Sets Single-Pole 2- & 4- pole configuration Single-Pole 3-pole configuration Panel Mounting Clamp Pole Series 175 & 350 Handle Kit Series 175, 180 & 350 Accessories Part Number Type Description Reducing Bushings / to 1/0 AWG /180 6 to 1/0 AWG /180 4 to 1/0 AWG /180 2 to 1/0 AWG /180 1 to 1/0 AWG /0 to 2/0 AWG Handle Kit Pole Red Pole Gray Pole Red Pole Gray Series 175 Dust Cover Assembly Series 175 & 180 Accessories Part Number Type Description Cable Clamps Clamp Single Conductor Clamp 2 Single Conductors Clamp Twin Conductor Cable Cable Clamp Single pole version pole version pole version Dust Cover Dust Cover Assembly (Shown) Dust Cover Housing 15

15 AMP Power Series Tooling AMP-O-LECTRIC Model G Terminating Machines, Part Nos , -9, -11 ( ) Semiautomatic bench machines for crimping reeled terminals and contacts, featuring a quiet and reliable direct motor drive, microprocessor controls for ease of setup and operation, and guarding and lighting designed for operator convenience and safety. All models are equipped with either manual or automatic precision adjustment of crimp height. Machinemounted sensors are available for crimp quality monitoring using conventional miniature-style applicators. For more information, request Catalog 65828, Video , Catalog [Crimp Quality Monitor (CQM)], Video AMP 3K/40 and AMP 5K/40 Terminating Machines ( ) The AMP 3K/40 and AMP 5K/40 Terminators are designed for customers that require the increased output and quality of a semiautomatic machine at a competitive price. By incorporating the most commonly requested features as standard and offering a long list of optional equipment, these terminators offer flexibility to meet the specific needs of various applications at the lowest possible cost. 3,000 lb [1361 kg] max. crimp force (AMP 3K/40); 5,000 lb [2268 kg] max. crimp force (AMP 5K/40) Toolless removal of applicators and guards Jog capability Quiet, fast operation 80/76 dba and cycle time less than seconds Accepts Heavy Duty Mini stye applicators Wide range of optional equipment such as toolless precision crimp height adjust, batch counter, CQM capability and work light For more information, request Catalog AMP-O-LECTRIC Model K Terminating Machine Part No ( ) AMP-O-LECTRIC Model K Terminating Machine with a permanently-mounted applicator that accepts interchangeable die sets to apply a variety of tapemounted terminals and splices. Many of the die sets can also be used in AMP-O-LECTRIC Terminating Machines with a tape applicator. For more information, contact Tyco Electronics. Stripping Module (for the AMP 3K/40 and AMP 5K/40 Terminating Machines and AMP-O-LECTRIC Model G Terminator) The combination of the Stripping Module with the AMP 3K/40 and AMP 5K/40 Terminating Machines or the AMP-O-LECTRIC Model G Terminator provides an economic and proficient method of stripping the wire and crimping terminals on the same machine. The module accepts Endand Side-Feed HDM Applicators (32-14 AWG) and operates in three modes: crimp only, strip only, or strip and crimp. It can be installed on existing machines in the field or purchased as one unit from the factory. For more information, request Catalog

16 AMP Power Series Tooling (Continued) Power Applicator Part Number (Customer Manual ) The Semiautomatic Power Applicator is designed to produce a carefully controlled uniform pressure crimp while providing a high rate of production. The applicator features matching dies that fully bottom at the completion of the crimp to provide proper crimp height. The one die set is fully adjustable to provide the full range of crimp heights for all wire sizes. 500 MCM Heavy Duty Cable Cutter Part No ( ) Designed to cut aluminum or copper cable up to 500 MCM. Light weight tubular steel handles with hand grips 21 overall length Cable Insulation Stripper/Slitter Part No ( ) Used on single or multiple conductor cable up to 1.75 in diameter Contact Extraction Tool Part No or standard insulated screwdriver Hand Tools for Cold-headed Contacts and Heavy-Duty Lug Terminals (Single-Indent Crimp) Tyco Electronics American Electrical Terminal (AET) For AMP Power Also For Heavy-Duty Lug Crimp Tool Part No Crimp Tool Part No. T-406 Series 50 and 75 Contacts OR Terminals (See pages 28, 29) Includes Adapter Includes Adapter Wire Size Wire Size Strip Length Part No. Part Number Marking Part Number Marking (AWG) (AWG) Strip Length /16 [11.11] A 5992 A [ ] /2 [12.70] B 5991 B 1/0 11/16 [17.46] 2/0 11/16 [17.46] 2 9/16 [14.29] C 5989 C 1 5/8 [15.87] No Adapter No Adapter 3/0 3/4 [19.05] 4/0 13/16 [20.64] Pneumatic Tools for Cold-headed Contacts (Dual-Indent Crimp) and Heavy-Duty Lug Terminals (See pages 28, 29) PICO* Pneumatic Tools** AMP Power Series Contacts 400 Series Power Unit Locator Series Wire Size (AWG) Part No. Preferred Alternate Die Preferred Alternate Closure Dim DA [3.86] 50/50 FPR/ BEC 400-BHD 414DA [3.86] DA [3.40] BEC 400-BHD 414DA None.200 [5.08] Series Power Unit DA [3.86] 50/50 FPR/ DEC 500-D 514DA [3.86] DA [3.40] DEC 500-D 514DA None.200 [5.08] / DA DA / DEC 500-D 514DA None.250 [6.35] DA MCM DA [13.34] 4/ DA [10.16] 350 3/ DEC 500-D 514DA None.360 [9.14] 2/ DA [8.26] 1/ DA [6.35] * Pacific Industrial Components (PICO) Corporation, 444 Constitution Ave., Camarillo, CA ; Tel: (805) ** Pneumatic Tool consists of a power unit, die, and locator; it can be used as a portable hand tool, bench-mounted hand tool, or foot-controlled unit. 17

17 AMPINNERGY Wire-To-Wire Connectors Product Facts Rated to 600 VAC (RMS) Flame retardant housings 94V-0 Housings, adapters, and power terminals keyed for proper assembly Stackable housings provide easy wire routing and neat wire dressing Built-in interlocking features better resist shock and vibration Usable as in-line connector, or as panel and surface mount connector Available in six different colors for circuit coding and identification Choice of two power terminals accommodates AWG and AWG conductors Recognized R under the Component Program of Underwriters Laboratories Inc., File No. E28476 CSA Certified, File No. LR7189 VDE Registered #5133 R AMPINNERGY Wire-To- Wire (WTW) Connectors provide a reliable and efficient means of interconnecting conductors employed to carry up to 600 VAC in power circuits or networks. The WTW Connectors consist of mating hermaphroditic, flame retardant polycarbonate housings into which customer terminated power contacts are inserted. Stackable in four directions through the use of molded interlocking keyways, the connectors make wire routing and dressing orderly and easy to accomplish. More importantly, the built-in interlocking features on the connectors and the accessory mounting adapters provide better resistance to the effects of shock and vibration, keeping the interconnect more stable and secure. The design features of the WTW Connector make it easily applicable to free hanging, surface mounted or panel mounted applications. By simply sliding the accessory mounting adapters into the molded keyways of the connector housing, a free hanging connector can be transformed into a surface mount connector or a panel mount connector. Customer supplied 8-32 screws and nuts may be used to secure the connectors configured with the mounting adapters to printed circuit boards or distribution panels. The same hardware may be used to secure the connectors to pre-cut openings in the panels. Furthermore, WTW Connector housings, mounting adapters and power terminals are all provided with alignment or keying features that make it difficult to improperly assemble and apply the connector. Alignment slots and tabs on the plastic connector housings provide for easy mating of the housings, even in the dark! Mounting adapters have a keyway on one side and a key on the other side providing for easy assembly to the connector by touch alone if necessary. And the power terminals have a side tab that helps prevent the incorrect insertion of the terminated conductor into the housing. Once inserted, the contacts firmly latch within the connector housing. The WTW Connector system is available in six different and distinctive colors which makes circuit differentiation and identification possible. The crimped power terminals will accommodate either AWG or AWG stranded conductors. Depending upon the conductor size and the number of conductors in the connector configuration, the current rating ranges from 10 amperes to 55 amperes. Technical Documents Product Specification AMPINNERGY WTW Connectors Application Specification Instruction Sheets AMPINNERGY Wire-To-Wire Stackable Connectors Inspection of AMPINNERGY System Power Contacts 18

18 AMPINNERGY Wire-To-Wire Connectors (Continued) Housings Material and Finish Housing Polycarbonate, 94V-0 For surface mounting and panel mounting information, see Instruction Sheet , AMPINNERGY Wire-To-Wire Stackable Connectors. Customer terminated power contacts are inserted into housings Free Hanging Interconnections Color Housing Part Numbers [36.91] Key Keyway White Black Green Red Blue Gray [9.80].386 [9.80] Wire-To-Wire Connector Housing Mounting Adapters Part Number Material and Finish: Housing Polycarbonate, Black.466 [11.84].696 [17.68].294 [7.47].177 [4.50].200 [5.08] Two mounting adpaters can be used with one or more connector housings to provide thru-panel or horizontal surface mounting capability of the completed assembly..190 [4.83].211 [5.36].405 [10.29] Keyway.231 [5.87] External Locking Latch Clip Part Number AMPINNERGY Wire-To-Wire Connector Housings have an integral locking feature designed to keep housings mated in most applications. Hower, the External Locking Latch Clip may be used as needed in applications where severe vibration or tension may pull mated housings apart. AMPINNERGY Wire-To-Wire Clips Part Number AMPINNERGY Wire-To-Wire Clips (Installed) Part Number

19 AMPINNERGY Wire-To-Wire Connectors (Continued) Power Terminals Material and Finish Contacts Copper alloy plated with [ ] minimum tin Loose Piece Part Number The Wire-To-Wire Connector Power Contacts are available in either strip form or in loose piece form. Contacts in strip form are terminated on continuous feed type terminators and the loose piece contacts are terminated with the hand tool or pneumatic tool. For wire preparation and crimped contact inspection information, refer to Instruction Sheet , Inspection of AMPINNERGY System Power Contacts. Part Number Contact Wire Size Hand Tool Pneumatic Tool Die Set Part Numbers (AWG) Part Number Part Numbers Part Numbers (loose piece) * (loose piece) *Requires C Head Adapter Part No and Adapter Holder Part No See Catalog for more information. Note: The same Hand Tool or Pneumatic Tool and Die Sets may be used to apply the Wire-To-Board Connector Terminals. Strip Form.145 [3.69] Part Number [6.74].730 [18.54] Nominal Feed Length.145 [3.69] Part Number [3.56] Part Number [6.68].730 [18.54] Nominal Feed Length.140 [3.56] Part Number Contact Part Numbers Wire Size (AWG) AMP-O-LECTRIC Model G Terminating Machine Applicator Part Numbers (strip) (strip) (strip) (strip)

20 AMPINNERGY Wire-To-Board Connectors Product Facts Ratings: 600 VAC (RMS), current ratings range from amps Receptacles polarized to plug Receptacles and plugs available in contact configurations of 2 through 8 positions Vertical receptacle polarized to PCB Receptacle contacts have dual solder posts for efficient heat dissipation, low millivolt drop and mechanical strength Receptacles may be mounted on PCBs.062 to.125 inch thick Plugs have positive latching to receptacles Removable crimp contacts latch firmly in plug Plugs are one-piece design Two ranges of crimped contacts accommodate either AWG or AWG conductors UL Recognized, File No. E28476 CSA Certified, File No. LR Technical Documents Product Specification AMPINNERGY WTB Connectors Application Specification AMPINNERGY WTB Connectors Instruction Sheets Installation of AMPINNERGY WTB Connectors Inspection of AMPINNERGY Contacts R R AMPINNERGY Wire-To-Board (WTB) Connectors Connectors provide a convenient and efficient means of delivering up to 600 VAC to component printed circuit boards and other power distribution devices in computers and peripherals, telephone systems and appliances. The WTB connectors also have automotive and industrial applications. Receptacles The AMPINNERGY WTB connector receptacles can be installed on pc boards varying in thickness from.062 inch to.125 inch. A polarizing pin is provided on the vertical receptacle assembly to aid in proper positioning on the pc board. Both the vertical and right-angle assemblies are polarized for accurate mating to the plug assemblies. The receptacle assemblies are available in contact configurations ranging from two to eight positions. Plugs The single piece plug housings are available in contact configurations to mate with the receptacles. The plug is equipped with positive latches to allow full and more secure mating to the respective receptacle. A make-first/break-last feature is designed into position 1 of the plug assemblies to provide grounding protection. Contacts The crimp contacts will accommodate either AWG or AWG conductors. The contacts latch firmly within the plug housing. 21

21 AMPINNERGY Wire-To-Board Connectors (Continued) Vertical PCB Receptacles Product Facts Withstands vapor phase, infrared and wave soldering processes.040 minimum standoff to PCB Polarized to PCB; to plug Contact centerline spacing:.440 Overall height on PCB:.600 Fits PCB thickness.062 through.125 Contacts have dual solder posts for efficient heat dissipation, low millivolt drop and mechanical strength Positive latching to mating plug.451 [11.46] Material and Finish Housing Polyphenylene Sulfide, Black, 94V-0 Contacts Tin Plated Copper Alloy.440 [11.18] Dim. A.050 [1.27] Typ. Housing.568 [14.43].192 [4.90].050 [1.27] Typ..065 [1.66].100 [2.54] Typ..130±.005 [3.30±.13] Dim. B Dim. C Contact.070±.003 [1.78±.08].130±.005 [3.30±.13].175 [4.45].110±.005 [2.79±.13].510 [12.95].440 [11.18] Typ. Dim. B.100 [2.54] Typ. 22 PCB Thickness.250 No. of Receptacle Positions Part Numbers PCB Thickness No. of Dimensions Receptacle Positions A B C Part Numbers

22 AMPINNERGY Wire-To-Board Connectors (Continued) Right-Angle PCB Receptacles Product Facts Withstands vapor phase, infrared and wave soldering processes.040 minimum standoff to PCB Receptacles polarized to plug Contact centerline spacing:.440 Overall height on PCB:.600 Fits PCB thickness.062 through.125 Contacts have dual solder posts for efficient heat dissipation, low millivolt drop and mechanical strength Positive latching to mating plug.568 [14.43].200 [5.08] Typ. Dim. A Dim. B.065 [1.66] Material and Finish Housing Polyphenylene Sulfide, Black, 94V-0 Contacts Tin Plated Copper Alloy.501 [12.73] Dim. C.440 [11.18].192 [4.90] Typ. Housing.050 [1.27] Typ. Contact.100 [2.54] Typ..200 [5.08].510 [12.95].440 [11.18].100 [2.54].063±.003 [1.60±.08].130±.005 [3.30±.13].130±.005 [3.30±.13] PCB Thickness No. of Dimensions Receptacle Positions A B C Part Numbers Dim. B 23

23 AMPINNERGY Wire-To-Board Connectors (Continued) Plug Housings Product Facts One-piece housing Polarized to mating receptacles Positive latching to mating receptacles Accepts crimp contacts P/N and Internal latching of crimp contact Material Housing Polycarbonate, Black, 94V-0 Dim. A [36.66] Dim. B.305 [7.75].371 [9.43].440 [11.18] 24 No. of Dimensions Plug Positions A B Part Numbers

24 AMPINNERGY Wire-To-Board Connectors (Continued) Crimp Contacts Product Facts Contacts are dual beam design Material and Finish Contacts Tin Plated Copper Alloy Wire barrel accepts one 10 or 12 AWG stranded copper conductor Part Number Strip Part Number Loose Piece.244 [6.20].735 [18.67] Application Tooling Applicator Part No (for Lead Makers) (for AMP-O-LECTRIC Model K Machine) (for AMP-O-LECTRIC Model G Machine).145 [3.70] [27.26].256 [6.51] Wire barrel accepts one 14, 16 or 18 AWG stranded copper conductor Part Number Loose Piece Part Number Strip Application Tooling Part No Hand Tool Die Set (14 AWG) Die Set (18-16 AWG) Extraction Tool.244 [6.20].145 [3.70] [27.26].735 [18.67].169 [4.30] 25

25 Technical Documents Various technical documents are available for your use: Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer AMPINNERGY WTB Connectors AMPINNERGY WTW Connectors Application Specifications describe requirements for using the product in its intended application and/or crimping information. They are intended for the Packaging and Design Engineer and the Machine Setup Person AMPINNERGY WTB Connectors AMPINNERGY WTW Connectors AMP Power Series 50 (Double-Pole) and 75 (Single Pole) Connector Assemblies AMP Power Series 120 (Single- and Double-Pole) Connector Assemblies AMP Power Series 175 (Double-Pole) and 180 (Single-Pole) Connector Assemblies AMP Power Series 350 (Double-Pole) Connector Assemblies AMP Power Series 15, 30 and 45 (Single-Pole) Connector Assemblies AMP Power Series 180 (Single-Pole) Connector Assemblies Instruction Sheets provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator Inspection of AMPINNERGY System Power Contacts Installation of AMPINNERGY WTB Connectors AMPINNERGY Wire-To-Wire Stackable Connectors AMP Power Series 50 Connector Assemblies AMP Power Series 175 and 350 Connector Assemblies with Cable Clamp Kits Heavy Duty Cable Cutter Hand Tool Heavy Duty Cable Cutter Hand Tool Heavy Duty Cable Cutter Hand Tool Crimp Tool Cable Stripper/Slitter Tool Handling of Reeled Products Test Summary /75 Product Evaluation /30/45 Product Evaluation Product Evaluation Competitive Evaluation AMP Power Series 175/180 Product Evaluation AMP Power Series 350 Product Evaluation Customer Manual AMP-O-LECTRIC Model K Terminator Machine

26 Part Number Index Note: This numerical index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. Page , , , ,7, ,7, ,7, ,7,8, ,7, ,7, , ,10, ,10, ,10, Part No. Page ,12, ,12, ,12, ,12, , , , , , , ,7, Tooling Part No. Page , , ,7, , , , , , ,7, ,7, ,7,8,17, T

27 Related Product Catalogs Heavy Duty Seamless Terminals and Splices Catalog The Heavy Duty Seamless and Copper Compression Lug and Splice line provides a robust terminal line for applications in the many industries. The product is used in applications including industrial and welding equipment, transportation/ marine cable harness, and general-purpose harnesses. The Heavy Duty Seamless line utilizes deep-draw stamping technology to create a robust terminal without butted seams along the wire barrel or along the outer edge of the ring tongue. The Heavy Duty Splice line offers butt splice versions with either flared or chamfered wire barrels for ease of wire entry and dimpled wire stops to assist in proper wire placement. The Copper Compression Lug and Splice line is a formed tubular line for use on cable assemblies in Commercial equipment and Industrial machinery. The thicker tongue and wire barrel of this line provide added strength and rigidity for more challenging applications. The Battery Lug and Splice line offers the thickest material and strength for your industrial equipment and transportation harness applications. Tyco Electronics has extensive drawn sleeve capabilities to help meet your customized electrical sleeve needs. The company manufactures specialized sleeves used in general electrical application and electrical components. Tyco Electronics has the capability to manufacture sleeves in a range of copper alloys and has extensive post electroplating capabilities. Contact us to review your application and discuss the benefits we can provide. Standard Terminals and Splices Catalog AMP solderless terminals and splices meet or exceed today s standards for reliable termination in applications ranging from control circuits to heavy duty power wiring. The catalog describes only standard terminals and splices accommodating wire sizes from 26 AWG through 4/0 AWG The terminals are pre-insulated and color coded by wire size for easy identification. Funnel entry on many terminals allows for easy wire insertion for high speed production Nylon or vinyl insulation provides high dielectric strength The serration or dimple feature inside the terminal barrel provides maximum barrel contact and tensile strength AMP s special plating process creates a high resistance to corrosion Use of AMP application tooling is designed for uniform high quality terminations UL, CSA, Military Approved AMPOWER Terminals and Splices Catalog The AMPOWER product line is available in a variety of terminal and splice styles to suit your design requirements. AMPOWER terminals and splices are ideally suited for power generation and distribution. This makes electrical equipment subject to continuous operation, such as generators, motors and welders, a perfect application for AMPOWER products. In addition, other applications include interconnections of power supplies to computers and peripheral equipment. 28

28 Related Product Catalogs (Continued) SOLISTRAND, Budget and DIAMOND GRIP Uninsulated Terminals and Splices Catalog SOLISTRAND and Budget terminals and splices are specially designed to terminate solid and stranded wire, irregular shaped conductors, and combinations of these retaining the superior performance characteristics of single-purpose terminals and splices. Corrosion resistance, vibration resistance and tensile strength of these terminals and splices are well within the limits of commercial and military specifications. The Budget terminal is primarily the same as the SOLISTRAND terminals without the brazed seam in the wire barrel. These terminals and splices fulfill the need for an economical and electrically superior termination where extreme vibration and tension on the wires are not present. DIAMOND GRIP utilizes a tin plated copper insulation support sleeve with "V" notches. The sleeve eliminates fraying of the insulation or breaking of the conductor. The "V" notches lock the wire insulation against vibration and pullout. Tyco Electronics Power Connectors and Interconnection Systems Catalog Tyco Electronics Power Connectors and Interconnection Systems Catalog features the largest grouping of high performance power connectors from Tyco Electronics. Most of the products are geared specifically for the high-end computer and telecommunications equipment markets, however, products for Industrial applications are included as well. The catalog includes power connectors mounted to printed circuit boards, discrete wires/cable assemblies and bus-bars. The "applications served" includes bulk power distribution from modular power supplies, low inductance connectors designed for microprocessor power delivery, backplane power interconnects meeting today s latest industry standards, and more. The newest products sold under the AMP and ELCON brands are now combined into a single comprehensive catalog. 29