Electrical submittal no data received July 2, 2015 has been reviewed by this office with the following disposition:

Transcription

1 SUBMITTAL REVIEW July 6, 2015 Melissa Guarin Beaverton School District SW Merlo Road Beaverton, OR Project: BSD Sunset High School Athletic Center Project No.: Dear Melissa: Electrical submittal no data received July 2, 2015 has been reviewed by this office with the following disposition: Item Manufacturer Action Structured Cabling Cable Manager Chatsworth No Exceptions Taken Cable Commscope No Exceptions Taken Flush Mounted Faceplate Commscope No Exceptions Taken Information Outlet Commscope No Exceptions Taken Patch Panel Commscope No Exceptions Taken The above submittal data has been reviewed only for conformance with the design concept and for compliance with information given in the Contract Documents, and this review does not extend to means, methods, techniques, sequence of construction, dimensions, quantities, or safety precautions thereto. Review does not relieve the contractor from responsibility for variations from the requirements of the Contract Documents. Returned herewith is one (1) copy of the above data. We are retaining one copy for our files. Please include a copy of this letter with each submittal package. Sincerely, Todd Thayer TDT/mmb P:\2014\ BSD Sunset HS Athletic Center\04 Construction Administration\Submittals\ \ _PAE Submittal Letter.docx

2 SUBMITTAL REVIEW PROJECT NAME Sunset HS Title IX Compliance Interiors and Concessions PROJECT # 7928 SUBMITTAL NAME Structured Cabling SUBMITTAL NUMBER DATE 07/07/15 REVIEWERS Jessica Faust Project Manager Chris Sandberg Inspector (Previous electrical lead) Jordan Beveridge IT Administrator COMMENTS: Approved as submitted. All okay. Chris 07/06/ in part 2. The below statement should be (2) cables for WAP. Part Modular Jack Outlets: A. Provide one (1) cable at all WAP locations Jordan 07/13/15 Reviewed. Jessica 07/13/15 District Goal: All students will show continuous progress toward their personal learning goals, developed in collaboration with teachers and parents, and will be prepared for post-secondary education and career success. The Beaverton School District recognizes the diversity and worth of all individuals and groups. It is the policy of the Beaverton School District that there will be no discrimination or harassment of individuals or groups based on race, color, religion, gender, sexual orientation, gender identity, gender expression, national origin, marital status, age, veterans' status, genetic information or disability in any educational programs, activities or employment.

3 Sunset High School NW Cornell Rd. Portland, OR To: BLRB ARCHITECTS, P.S. Date: 07/01/2015 Attn: RICHARD HIGGINS 1001 SW 5TH AVE., SUITE 1100 Contact Phone: PORTLAND, OR Contact CC d: SUBMITTAL TRANSMITTAL FOR APPROVAL Submittal #: 75 Rev.#: 0 In Accordance with Specification Section #: This is a submittal for Structured Cabling items per the table below as reviewed and noted by Pavilion Construction NW, LLC, and provided by. Please provide a response to this submittal by 07/11/2015. Pavilion Status: Sent/Submitted Notes: Submitted By: Riley Tobin Phone: (503) Address: rtobin@pavilionconstruction.com Fax: (503) Architect s Response SUBMITTAL RESPONSE Schedule Tracking Proceed Date Received from Sub/Sup 06/30/2015 Proceed, as noted Date Requested to be returned 07/11/2015 Revise and Resubmit Date Returned from Architect Material Return without Review Date Returned to Sup/Sup Comments: PAVILION CONSTR JCTION LLC o APPROVED AS SUBMITTEO o OISAPPROVEO, PlIASE SUBMIT COPlES o APPRDVEOAS NOTEO o F()R THE RECORD RY: _ Riley _ Tobin DATED: 06/23/15 7/1/15 This submittal has been reviewed for general "onformil."'.ce with ttle contract documents. Tn's review does not reuevs the supplier of responsibility for erro~, omissions or any dtviition tram the requirem ents of the ",..... r?c! :!vr:umems. Pavilion Construction NW, LLC 4700 SW Macadam Ave. Portland, OR Phone: (503) Fax: (503) Page 1 of 1

4 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 SECTION STRUCTURED CABLING PART 1 - GENERAL A. This document describes general scope, products and execution requirements relating to furnishing and installing the internal Telecommunications Cabling. B. Backbone and horizontal cabling comprised of Copper and Fiber Cabling, and support systems are covered under this document. All installations are warrantied and are required to be pre-registered with approved manufacturers before work begins. C. The Horizontal (workstation) Cabling System shall consist of a minimum of (1) Category 6, 4-pair Unshielded Twisted Pair (UTP) Copper Cable to each work area outlet unless otherwise noted for specific locations. The cables shall be installed from the Work Area Outlet to the designated Telecommunications located in the building, and routed to the designated rack or backboard serving that area and terminated as specified in this document. D. All cables and related pathways, supports, terminations, and grounding hardware shall be furnished, installed, wired, tested, labeled, and documented by the Telecommunications Contractor as detailed in this document. E. Product specifications, general design considerations, and installation guidelines are provided in this document. Quantities of telecommunications outlets, typical installation details, cable routing and outlet types are provided as project specific information by contract specification and/or contract drawings. The Contractor shall meet or exceed all requirements for any infrastructure system as detailed within this document. This document shall be referenced within the projects specific scope of work. F. This document does not replace any code, either partially or wholly. The contractor must be aware of local codes that may affect the project. 1.2 REGULATORY REFIDFENCES A. All work and materials shall conform in every detail to the rules and requirements of the National Fire Protection Association, the local Electrical Code and present manufacturing standards. B. All materials shall be UL Listed and shall be marked as such. If UL has no published standards for a particular item, then other national independent testing standards shall apply and such items shall bear those labels. Where UL has an applicable system listing and label, the entire system shall be so labeled. C. The cabling system described in this is derived from the recommendations made in recognized telecommunications industry standards. The most recent versions of the following documents are incorporated for reference: 1. ANSI/TIA/EIA B: Optical Power Loss Measurements of Installed Multimode Fiber Cable Plant 2. ANSI/TIA/EIA-568-C.1-: Commercial Building Telecommunications Cabling Standard, Part 1: General Requirements, 3. ANSI/TIA/EIA-568-C.2-: Commercial Building Telecommunications Cabling Standard, Part 2: Balanced Twisted Pair Cabling, BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

5 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, ANSI/TIA/EIA-568-C.3-: Commercial Building Telecommunications Cabling Standard, Part 3: Fiber optic Cabling Components Standards, 5. TIA -569-C: Commercial Building Standard for Telecommunications Pathways and Spaces, 6. ANSI/TIA/EIA-598-C: Color Coding of Fiber-Optic Cables, 7. ANSI/TIA/EIA-606-B: The Administration Standard for the Telecommunications infrastructure of Commercial Building, 8. TIA-607-B: Commercial Building Grounding and Bonding Requirements for Telecommunications, 9. ANSI/TIA/EIA-758-B: Customer Owned Outside Plant Telecommunications Cabling Standard, D. NFPA-70: National Electric Code (NEC) 1. BICSI (Building Industries Consulting Services International) - Telecommunications Distribution Methods Manual (TDMM) 2. National Fire Protection Agency (NFPA 70), National Electrical Code (NEC) National Fire Protection Agency (NFPA 70), National Electrical Code (NEC) 4. Beaverton School District (BSD) Division 27 Communications and Technology Design Standard. E. If this document and any of the documents listed above are in conflict, then the more stringent requirement shall apply. All documents listed are believed to be the most current releases of the documents. The Contractor has the responsibility to determine and adhere to the most recent release when developing the proposal for installation. 1.3 WORK INCLUDED A. Demolition of existing telecommunications cabling, connectivity and supports B. Contractor work consists of furnishing all labor, equipment, materials, and supplies and performing all operations necessary to complete the installation of a structured cabling system in compliance with the specifications and drawings. C. The Work shall include, but not be limited to the following: 1. Furnish and install a complete telecommunications wiring infrastructure and ANSI/TIA/EIA 607-B compliant Grounding and Bonding system as specified in Grounding AND Bonding for Communications systems. 2. Furnish, install, test and label all UTP and Optical Fiber cables, splice cables, 110 IDC termination blocks, interdict, ports, faceplates, inserts, connector panels and patch panels. 3. Furnish and install all racks, cabling supports, work area outlets, inserts, patch panels, and patch cords (when specified). 4. Furnish all material and labor required to form a complete system. 5. Perform link and channel testing (100% of horizontal and/or backbone links/channels) and certification of all components. 6. Furnish test results of all cabling to the Architect and the Owner in electronic format, listed by each communication closet, then by workstation ID. Test results shall be tabbed per Equipment Room. 7. Provide Owner training and documentation. (Testing documentation and As-built drawings). 1.4 SUBMITTALS A. General: 1. Work shall not proceed without Architect and Owner approval of the submitted items. BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

6 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, The guidelines set forth in this section pertain to all Division 27 specifications included in this project. 3. The following guidelines and deliverables shall be submitted to the Owner and Architect prior to installation commencement. 4. Submit all proposed products for use in communications systems in accordance to the guidelines set forth herein. See Pages 9-22 B. Informational Submittals: 1. Proposed labeling examples for Patch Panels, Faceplates and Work Area Outlet jacks. 2. Field Test Reports: Submit sample cable test reports showing report format and parameters tested. Will be included under seperate cover C. Shop Drawings: 1. The Drawings that accompany this Division 27 Specifications are diagrammatic. They do not show every offset, bend, tee, or elbow that may be required to install work in the space provided and avoid conflicts. Offsets and transitions shall be assumed at a minimum at each duct crossing, structural penetrations through shear walls or beams, structural grids where ceiling heights are restricted. Follow the Drawing as closely as is practical to do so and install additional bends, offsets and elbows where required by local conditions from measurements taken at the Building, subject to approval, and without additional cost to the Owner. The right is reserved to make any reasonable changes in outlet location prior to roughing-in, without cost impact. D. The Contract Drawings indicate the general layout of the major communications pathways, and various items of equipment. Coordination with other trades and with field conditions will be required. For this purpose, prepare Shop Drawings of all equipment installations. Shop Drawings shall be new drawings prepared by Contractor and not reproductions or tracings of Architect s Drawings. Overlay drawings with shop drawings of other trades and check for conflicts. All drawings shall be same size as Architect s Drawings with title block similar to Contract Drawings and identifying Architect s drawing number or any reference drawings. All drawings shall be fully dimensioned including both plan and elevation dimensions. Shop drawings cannot be used to make scope changes. E. Equipment / Products: 1. Submit at one time the related submittals for the products called out in all Division 27 specifications. 2. Two indexed sets of manufacturer's technical data for each product including product description, specifications including labeling or listing by an agency acceptable to the Owner, and storage requirements. 3. Where more than one product is called out on the same sheet, clearly highlight or mark which product is proposed for use. F. Firestop design basis documentation that shall include each type of communication penetration, type of building construction being penetrated including the hourly resistance rating of floor, wall, or other partition of building construction into which Firestop design will be installed, and Firestop device or system proposed for use. G. All submittals shall be approved by Owner authorized representative before installation implementation. BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

7 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 H. Project Closeout 1. Manufacturer's Installation, Start-Up and Adjustment Instructions. 2. Operation and Maintenance Data. 3. Special Warranty: Contractor shall not offer a special warranty to owner to supplement the standard warranty requirement covered in this specification. a. With respect to the installation of Approved Manufacturers cabling system, furnish Approved Manufacturers Cabling System application / system standard warranty. I. The Telecommunications Contractor shall receive written approval from the Architect and Owner on all substitutions of material. No substituted materials shall be installed except by written approval from the Architect and Owner s authorized representative. Substitution requests shall be made in writing prior to bid closing as required by the solicitation documents, but in no case less than five working days before bid closing. Requests for substitution shall also have manufacturer product specification sheets along with any cost changes attached for every product being requested. The Architect and Owner reserve the right to approve or deny requests at their discretion. J. All substitution requests shall be submitted under the guidelines set forth in Division 1 documents. K. The Category 6 portion of the cabling system shall comply with the proposed link and channel performance requirements of the latest revision of ANSI/TIA-568-C.1 Performance Specifications for 4-pair 100 Ohm Category 6 Cabling. The system warranty shall be facilitated by the Contractor and be established between the Customer and the cabling system manufacturer. Contractor derived warranties will not be accepted. PART 2 - PRODUCTS 2.1 Horizontal Distribution A. Copper Distribution Cables: B. Category 6 Horizontal Cable 1. Horizontal cabling shall be AWG, 4-pair UTP, UL/NEC/NFPA CMP rated. 2. Cable jacketing shall be lead-free. 3. Cable shall be 3rd party verified to ANSI/TIA/EIA-568-B.2.1 and meet the performance requirements listed in the table below in addition to all other standard Category 6 performance requirements. Cable shall be safety listed to ANSI/UL Color: Blue a. Approved Manufacturers 1) Panduit 2) Commscope 3) Or approved equal 2.2 Modular Jack Faceplates: A. Wall mounted Faceplates: 1. Faceplates shall be constructed of ABS molding compound and be 4.53 X 2.77 X.60 in size. Each faceplate shall contain three (3) jack ports. Each port shall be provided with an icon to indicate its function. 2. Faceplates shall accommodate two labels and provide a clear polycarbonate cover for each. 3. Provide blank inserts for all unpopulated ports. a. Approved Manufacturer BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

8 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, ) Panduit 2) Commscope 3) Or approved equal 2.3 Modular Jack Outlets: A. Provide one (1) cable at all WAP locations. B. Provide specified cable amount at all other locations. C. Provide one (1) cable at all clock locations shown. D. All modular jacks shall be wired to the T568B wiring pattern. E. Modular jacks shall be terminated using a 110-style pc board connector (made of 94V-0 rated polycarbonate), color-coded for both T568A and T568B wiring. The 110 connector shall terminate AWG solid conductors with a maximum insulation diameter of.050 inches. F. Category 6 modular (data) jacks shall be unkeyed 4-pair and shall meet the performance requirements listed in the table below. Modular jacks shall fit in a.790" X.582" opening. Modular jacks shall be terminated using a 110-style pc board connector, color-coded for both T568A and T568B wiring. Each jack shall be wired to T568B. G. Coordinate with the BSD authorized representative for Outlet jack colors. 2.4 pathway systems A. The contractor is responsible for providing all pathway systems to provide the owner a complete and functional system. 2.5 Firestopping systems A. The contractor is responsible for providing all firestopping systems as shown on the drawings or as required as specified by the mechanical and architectural egress plans. B. Firestops shall provide F ratings which meet or exceed those specified in Architectural plans. C. Firestops shall be provided with the same usable area as the open pathway system it is serving. D. All firestopping systems used for communications cabling use shall be reusable type and provide access to all cabling through it. E. Cementitous firestopping systems are not permitted for communications use. 1. Approved Manufacturers a. STI EZ-Path b. Hilti CPS BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

9 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, Miscellaneous Materials: A. Screws, nuts, bolts, washers, tools, sealants, sleeves, fire stop, riser collars, rack anchors, ground clips and ground wire, backboards, mushrooms, wire minders, D-brackets, labeling materials, etc., as required to provide a trim and working, turnkey system that conforms to all applicable codes and regulations. PART 3 - EXECUTION 3.1 general A. Perform all installation work in a neat, high quality manner and in conformity with local and federal building codes. B. Cable routes must be field engineered to avoid obstruction by ducts and other material in the ceiling space. C. Fire stop all core holes and sleeves used for riser and tie cable installation between floors or through fire-rated walls. D. Place cables with sufficient bending radius so as not to degrade signal carrying capacity nor to kink, shear, or damage outside sheath. E. Manufacturer's pulling tension specifications must be adhered to for installing cable so as not to stretch cable or reduce optical performance characteristics. F. Use of existing ceiling wires, plumbing, conduits, sprinkler pipes, or air handling structures for attachment of cables is expressly prohibited. G. Maintain at least 12 inches separation between all unshielded copper communications cables and light fixtures or parallel runs of conduit containing power cables. H. Ceiling tiles broken or defaced by the cabling installer during the installation and testing process must be replaced to the satisfaction of the Owner. I. Advise the Architect immediately of any conditions that might delay or impede cable installation or affect the quality of the installed cable plant. Proceed with questionable segment only after the Architect has had the opportunity to review those conditions. 3.2 FIELD EXAMINATION A. Outlet locations and other dimensions on the Electrical and Cabling drawings are only approximate. Verify locations and routes by inspecting the site prior to installation. 3.3 SITE PREPARATION A. It will be the responsibility of the cabling installer to keep the work area free of debris, trash, empty cable reels, scrap wire, etc., and to dispose of these materials on a daily basis. BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

10 Sunset High School - Title IX and Upgrades Beaverton School Dstrict No. 48 BLRB Project No.: 14.84P Permit Set May 15, INSTALLATION A. Category 6 Horizontal Station Cables: 1. Install 4-pair Category 6 cables between the appropriate IDF and each outlet as shown on the drawings. Route these cables to the IDF using conduit and/or install support wires to structure as necessary in the ceiling space. At the station end, terminate each Category 6 cable on a Category 6 jack and install in an appropriate faceplate. At the IDF end, terminate the station cables in sequential order on Category type patch panel on equipment racks. Comply with a cable numbering sequence provided by Owner. The actual number of 4-pair Category 6 cables required at each outlet are indicated on the drawings. 2. Install Category 6 patch panels on rack-mounted racks in each IDF as required to accommodate the station pairs routed to each IDF room. 3. Comply with all installation practices listed in EIA/TIA 568 B.2-1 guidelines. 4. Terminate all horizontal cable to T568B standard. 5. In terminating Category 6 cables, the amount of untwisting on each pair must be limited to 0.5 inches. 6. The amount of untwisting of jumper wire must also be limited to 0.5 inches. 7. Strip back only as much of the jacket of any Category 6 cable as is necessary to administer connecting hardware terminations. 8. Prescribed pulling tensions must be observed for all cables installed. 9. Cable bundles must be tie wrapped with minimum cinching pressure so as not to compress the dielectric. 10. Cable bend radii must be limited to eight times the cable diameter. This means that care must be taken not to kink the cable during installation, as a kink by definition violates the minimum bending radius of the cable. 11. Bend radius for cable bundles must be limited to eight times the diameter of the cable bundle. 3.5 TESTING and LABELING A. All Data Outlets shall be labeled in accordance with BSD labeling standard for data drops. The labels shall be non-removable, typed or machine-engraved. The label shall identify the Data Distribution Room, patch panel, and port number on the patch panel to which the horizontal cable terminates. Data outlet labels shall be installed into the recess label field on the faceplate. END OF SECTION BLRB Architects - Portland, Oregon PAE STRUCTURED CABLING

11 Division 27 Submittals

12 EQUIPMENT SUBMITTAL for Sunset HS Title IX Upgrades Structured Cabling System as proposed by G.B. Manchester Corp. CCB# MFG DESCRIPTION PART # CPI 2U Horizontal Wire Manager commscope Category 6 CMP Cable, Blue /10 commscope 2-port faceplates M12L-246 commscope commscope commscope Allentel Cat6 Jack, Ivory Cat6 Jack, Orange 48-port patch panel Cat6 Cat6 patch cords UNJ600-IV UNJ600-OR UNP-U-610-2U-48 AT1603-GY

13 Product Cut Sheet UNIVERSAL HORIZONTAL CABLE MANAGER Create an attractive and highly functional horizontal pathway for patch cords and multimedia applications using coax, copper and fiber optic cables. After routing the cables or cords, simply snap on the cover for a clean, professional appearance. Extra-wide and contoured cable guide fingers, spaced 1.75 (44.5 mm) apart, separate and organize patch cords for quick and easy moves, adds and changes. The cable guides are offset to ensure proper bending radii of patch cables, even hooded patch cables Patented fingers meet the requirements of UL 94V-0 flammability rating Snap-on covers are easy to use and open 180 up or down with adjacent installation Covers and panel have a black powder-coat textured finish, reducing fingerprints and smudges Estimated cable capacities: See the cable fill table at Part Number Double-Sided Cable Manager Description H x W x D in (mm) Single-Sided Cable Manager Shipping Weight lb (kg) X19 1U x 19 x (297.9) 5 (2.3) X23 1U x 23 x (297.9) 6 (2.7) X19 2U x 19 x (297.9) 6 (2.7) X23 2U x 23 x (297.9) 7 (3.2) X19 3U x 19 x (297.9) 6 (2.7) X23 3U x 23 x (297.9) 7 (3.2) Part Description Shipping Number H x W x D Weight in (mm) lb (kg) X19 1U x 19 x 4.96 (126.0) 2 (0.9) X23 1U x 23 x 4.96 (126.0) 3 (1.4) X19 2U x 19 x 5.14 (130.6) 3 (1.4) X23 2U x 23 x 5.14 (130.6) 4 (1.8) X19 3U x 19 x 5.14 (130.6) 4 (1.8) X23 3U x 23 x 5.14 (130.6) 5 (2.3) X19* 1U x 19 x 6.26 (159.0) 3 (1.4) X23* 1U x 23 x 6.26 (159.0) 3 (1.4) X19* 2U X 19 X 6.44 (163.6) 4 (1.8) X23* 2U X 23 X 6.44 (163.6) 5 (2.3) X19* 3U X 19 X 6.44 (163.6) 5 (2.3) X23* 3U X 23 X 6.44 (163.6) 6 (2.7) Part Number Dimensions 19" 23" A a B b (43.9) 1.02 (25.9) (88.4) 2.77 (70.4) (132.8) 4.52 (114.8) (43.9) 1.02 (25.9) (88.4) 2.77 (70.4) (132.8) 4.52 (114.8) (43.9) 1.00 (25.4) 1.67 (42.4) 0.85 (21.6) (87.9) 2.75 (69.9) 3.42 (86.9) 2.60 (66.0) Use Universal Horizontal Cable Manager in conjunction with the CPI Patch Panel Wire Management Bar (P/N X01) and any of CPI s vertical cabling sections for clean, organized cable management (132.8) 4.50 (114.3) (131.3) 4.44 (112.8) X=color: 7=Black, E=Glacier White. *Note: Deep Panel is used when Double-Sided MCS Master Cabling Sections are center-mounted on 3 D racks in U.S. & Canada Chatsworth Products, Inc. All rights reserved. CPI, CPI Passive Cooling, GlobalFrame, MegaFrame, Saf-T-Grip, Seismic Frame, SlimFrame, TeraFrame, Cube-iT Plus, Evolution, OnTrac, Velocity and QuadraRack are federally registered trademarks of Chatsworth Products. econnect and Simply Efficient are trademarks of Chatsworth Products. All other trademarks belong to their respective companies. Rev.3 07/13

14 Product Specifications / BLUE CPK Media Category 6 U/UTP Cable, plenum, blue jacket, 4 pair count, 1000 ft (305 m) length, CommPak Cross Section Drawing Construction Materials Conductor Material Insulation Material Jacket Material Separator Material Bare copper FEP Polyolefin PVC FEP Dimensions Cable Length Cable Weight Diameter Over Jacket Jacket Thickness 305 m 1000 ft lb/kft mm in mm in Electrical Specifications ANSI/TIA Category 6 dc Resistance Unbalance, maximum 5 % dc Resistance, maximum 6.66 ohms/100 m Delay Skew 45 ns Mutual Capacitance 5.6 nf/100 1 khz Nominal Velocity of Propagation (NVP) 73 % Operating Frequency, maximum 250 MHz Transmission Standards ANSI/TIA 568 C.2 CENELEC EN ISO/IEC Class E Safety Voltage Rating 300 V Dielectric Strength, minimum 1500 Vac 2500 Vdc 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 20, 2012 page 1 of 3 March 6, 2012

15 Product Specifications / BLUE CPK Note All electrical transmission tests include swept frequency measurements Environmental Specifications Environmental Space Flame Test Method Installation Temperature Operating Temperature Smoke Test Method Plenum CMP 0 C to +60 C (+32 F to +140 F) 20 C to +60 C ( 4 F to +140 F) CMP General Specifications Brand Media 6 Uniprise Cable Component Type Horizontal Cable Type U/UTP (unshielded) Pairs, quantity 4 Jacket Color Blue Conductor Gauge, singles 23 AWG Conductor Type, singles Solid Conductors, quantity 8 Separator Type Tape separator Packaging Type CommPak box Product Number Mechanical Specifications Pulling Tension, maximum 11 kg 25 lb Regulatory Compliance/Certifications Agency Classification RoHS 2002/95/EC Compliant ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 20, 2012 page 2 of 3 March 6, 2012

16 Product Specifications / BLUE CPK Electrical Performance Std Standard (ANSI/TIA 568) Typ Typical IL Insertion Loss (db/100m) ACRF Attenuation to Crosstalk Ratio Far End (db/100m) NEXT Near End Crosstalk (db/100m) PSACRF Power Sum Attenuation to Crosstalk Ratio Far End (db/100m) ACR Attenuation to Crosstalk Ratio (db/100m) RL Return Loss (db) PSNEXT Power Sum Near End Crosstalk (db/100m) TCL Transverse Conversion Loss (db/100m) PSACR Power Sum Attenuation to Crosstalk Ratio (db/100m) ELTCTL Equal Level Transverse Conversion Transfer Loss (db/100m) Freq. MHz IL NEXT ACR PSNEXT PSACR ACRF PSACRF RL TCL ELTCTL Std Typ Std Typ Std Typ Std Typ Std Typ Std Typ Std Typ Std Typ Std Std CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 20, 2012 page 3 of 3 March 6, 2012

17 Product Specifications M12L-246 L Type Flush Mounted Faceplate, two port ivory l Available for use with the DYMO labeling solution Dimensions Depth 7.37 mm 0.29 in Height mm 2.81 in Weight 0.04 kg 0.09 lb Width mm 4.81 in Environmental Specifications Safety Standard cul UL General Specifications Color Ivory Mount Type Flush Total Ports, quantity 2 Product Type Flush mount modular faceplate Application Used with M Series modular information outlet Package, quantity 1 Mechanical Specifications Material Type High impact, flame retardant, UL rated 94 V 0, thermoplastic Regulatory Compliance/Certifications Agency ISO 9001:2008 Classification Designed, manufactured and/or distributed under this quality management system 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 19, 2012 page 1 of 1 March 5, 2012

18 Product Specifications CC /1 UNJ600-IV Uniprise UNJ600 Category 6 U/UTP Information Outlet, ivory Dimensions Depth Height Width mm 1.20 in mm 0.80 in mm 0.80 in Electrical Specifications ANSI/TIA Category 6 Contact Resistance Variation, maximum Contact Resistance, maximum 20 mohm 100 mohm Current Rating C F Dielectric Withstand Voltage, RMS, conductive surface Hz Dielectric Withstand Voltage, RMS, contact to contact Hz Insulation Resistance, minimum 500 MOhm Environmental Specifications Flammability Rating UL 94 V 0 Operating Temperature 10 C to +60 C (+14 F to +140 F) Relative Humidity Up to 95%, non condensing Safety Standard cul UL Storage Temperature 40 C to +70 C ( 40 F to +158 F) General Specifications Brand Uniprise Cable Type U/UTP (unshielded) Color Ivory Product Type Outlet Package, quantity 1 Mechanical Specifications Conductor Gauge, solid Conductor Gauge, stranded Conductor Type Material Type Outlet/Module Contact Plating Plug Insertion Life, minimum 22 AWG 24 AWG 26 AWG 22 AWG 24 AWG Solid Stranded (7 strands) Copper alloy High impact, flame retardant, thermoplastic Precious metals 750 times 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 19, 2012 page 1 of 2 March 5, 2012

19 Product Specifications CC /1 UNJ600-IV Plug Insertion Life, test plug Plug Retention Force, minimum Rear Termination Contact Plating Rear Termination Type Wiring IEC compliant plug 30 lbf 133 N Precious metals IDC T568A T568B Regulatory Compliance/Certifications Agency Classification RoHS 2002/95/EC Compliant ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 19, 2012 page 2 of 2 March 5, 2012

20 Product Specifications CC /1 UNJ600-OR Uniprise UNJ600 Category 6 U/UTP Information Outlet, orange Dimensions Depth Height Width mm 1.20 in mm 0.80 in mm 0.80 in Electrical Specifications ANSI/TIA Category 6 Contact Resistance Variation, maximum Contact Resistance, maximum 20 mohm 100 mohm Current Rating C F Dielectric Withstand Voltage, RMS, conductive surface Hz Dielectric Withstand Voltage, RMS, contact to contact Hz Insulation Resistance, minimum 500 MOhm Environmental Specifications Flammability Rating UL 94 V 0 Operating Temperature 10 C to +60 C (+14 F to +140 F) Relative Humidity Up to 95%, non condensing Safety Standard cul UL Storage Temperature 40 C to +70 C ( 40 F to +158 F) General Specifications Brand Uniprise Cable Type U/UTP (unshielded) Color Orange Product Type Outlet Package, quantity 1 Mechanical Specifications Conductor Gauge, solid Conductor Gauge, stranded Conductor Type Material Type Outlet/Module Contact Plating Plug Insertion Life, minimum 22 AWG 24 AWG 26 AWG 22 AWG 24 AWG Solid Stranded (7 strands) Copper alloy High impact, flame retardant, thermoplastic Precious metals 750 times 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 19, 2012 page 1 of 2 March 5, 2012

21 Product Specifications CC /1 UNJ600-OR Plug Insertion Life, test plug Plug Retention Force, minimum Rear Termination Contact Plating Rear Termination Type Wiring IEC compliant plug 30 lbf 133 N Precious metals IDC T568A T568B Regulatory Compliance/Certifications Agency Classification RoHS 2002/95/EC Compliant ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 19, 2012 page 2 of 2 March 5, 2012

22 Product Specifications CC /1 UNP610-48P Uniprise Category 6 Patch Panel, 48 port l Available for use with the DYMO labeling solution Dimensions Depth mm 1.75 in Diameter Over Dielectric, maximum mm in Diameter Over Dielectric, minimum mm in Height mm 3.50 in Width mm in Electrical Specifications ANSI/TIA Category 6 Current Rating C F Dielectric Withstand Voltage, RMS, conductive surface Hz Dielectric Withstand Voltage, RMS, contact to contact Hz Insulation Resistance, minimum 500 MOhm Environmental Specifications Flammability Rating UL 94 V 0 Operating Temperature 10 C to +60 C (+14 F to +140 F) Relative Humidity Up to 95%, non condensing Safety Standard cul Storage Temperature 40 C to +70 C ( 40 F to +158 F) UL General Specifications Brand Uniprise Cable Type U/UTP (unshielded) Modules, quantity 8 Product Type Panel Total Ports, quantity 48 Color Black Package, quantity 1 Rack Type EIA 19 in Rack Units 2 Mechanical Specifications Conductor Gauge, solid 22 AWG 24 AWG 26 AWG Conductor Gauge, stranded 22 AWG 24 AWG Conductor Type Solid Stranded (7 strands) Material Type High impact, flame retardant, thermoplastic Outlet/Module Contact Plating Precious metals Powder coated steel 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 27, 2012 page 1 of 2 March 5, 2012

23 Product Specifications CC /1 UNP610-48P Plug Insertion Life, minimum Plug Insertion Life, test plug Plug Retention Force, minimum Rear Termination Contact Plating Rear Termination Type Wiring 750 times IEC compliant plug 30 lbf 133 N Precious metals IDC T568A T568B Regulatory Compliance/Certifications Agency Classification RoHS 2002/95/EC Compliant ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system 2012 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See for the most current information. Revised: February 27, 2012 page 2 of 2 March 5, 2012

24