Version 1.0 BLAISE UTILITY 4 CUBE 2 DOOR.

Transcription

1 Version 1.0 BLAISE UTILITY 4 CUBE 2 DOOR

2 Enjoy Your purchase from Australia s Best Value Furniture Store PAGE 2

3 Assembly Checklist Read through the instructions carefully before you begin. Identify and lay out all of the components before you begin assembly. Make sure you have all the required tools. Never use power tools unless instructed. Unless instructed, do not fully tighten screws until the item is fully assembled. Useful Information! Never use power tools unless specifically instructed. They can damage your components or hardware if used incorrectly.! The most common mistakes made during assembly are using the wrong hardware or getting components back to front.! Always use a soft surface (such as carpet or cardboard) when assembling your product to avoid scratching or damaging the surface of the product.! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be used in as they may not fit through a door once assembled.! Never use any glue until you are certain that the parts belong together.! Periodically check and re-tighten all fasteners. Check the product care label or website for product care instructions.! If you are having any difficulties assembling your product, missing any hardware or components please visit our website Help Centre for further assistance. PAGE 3

4 What you need to assemble the product DO NOT USE Other tools you need P2 P6 P6 P2 8 x Dowels (H1) 12 x Large (H2) 4 x Down Rollers 8 x Medium (H7) (H8) 12 x Paper Covers (H3) 8 x Back Panel Holders (H4) 4 x Upper Rollers 8 x Small (H6) (H5) 8 x Small Round Head Screws (H9) 2 x Metal Plates 8 x Large (H10) Round Head Screws (H11) 1 x Glue (H12) PAGE 4

5 Step 1 H9 H7 4 x Upper Rollers (H6) H9 4 x Down Rollers (H7) H7 H8 H6 8 x Medium 8 x Small Round Head Screws (H8) (H9) H8 H6 - Attach 2 x Upper Rollers (H6) to Door () use 4 x Medium (H8). - Attach 2 x Down Rollers (H7) to Door () use 4 x Small RoundHead Screws (H9). - Repeat for other Door (). Step 2 H1 8 x Dowels (H1) 1 x Glue (H12) H12 - Squeeze Glue (H12) into Dowel holes in Panel (). - Insert 4 x Dowels (H1) into Panel () as shown. - Repeat for other Panel (). PAGE 5

6 Step 3 1 x Glue (H12) H12 P3 - Squeeze Glue (H12) into Dowel holes in Panel (P3). - Attach 2 x Panels () to Panel (P3). Step 4 H2 4 x Large (H2) P3 H2 - Attach 2 x Panels () to Panel (P3) use 4 x Large (H2). PAGE 6

7 Step 5 P6 - Insert 1 x Back Panel (P6) into grooves in 2 x Panels (). Step 6 1 x Glue (H12) 4 x Large (H2) H12 H2 P2 - Squeeze Glue (H12) into Dowel holes in Panel (P2). - Attach Panel (P2) to Panels ()&() use 4 x Large (H2). PAGE 7

8 Step 7 P6 - Insert 1 x Back Panel (P6) into grooves in 2 x Panels (). Step 8 H2 1 x Glue (H12) 4 x Large (H2) H12 P2 - Squeeze Glue (H12) into Dowel holes in Panel (P2). - Attach Panel (P2) to Panels ()&() use 4 x Large (H2). PAGE 8

9 Step 9 H4 H5 12 x Paper Covers (H3) 8 x Back Panel Holders (H4) 8 x Small (H5) H4 H5 H3 - Screw 8 x Back Panel Holders (H4) to Cube back use 8 x Small Flat head Screws(H5) as shown. - Stick 12 x Paper covers (H3) to cover the Screw holes. Step 10 - Put 2 x Doors () into the slide as shown. PAGE 9

10 Step 11 H7 - Slide the Doors (). You can adjust the Down Roller (H7) as shown for Door move smooth. Step 12! - Don t hang the Cube on wall. PAGE 10

11 Step 13 4 x Metal Plates (H10) 8 x Large Round Head Screws (H11) H10 H11 - You can stack the Cube maximum number 3. - Connect 2 Cube on back with 2 x Metal Plates (H10) and 4 x Large Round Head Screws (H11) Step 14!! Note:The correct type of wall screws must be used for your wall.please seek professional advice if in doubt. This is an anti-topple strap fitted to the back of Cube, Choose a suitable wall fixing, and then fasten the strap to the wall as shown. PAGE 11

12 Step 15 Job Complete! In the interest of our environment please dispose of all packaging thoughtfully. PAGE 12