Version 1.1 TWO PEOPLE CODA BOOKCASE 10 SHELF REQUIRED.

Transcription

1 Version 1.1 TWO PEOPLE CODA BOOKCASE 10 SHELF REQUIRED

2 Enjoy Your purchase from Australia s Best Value Furniture Store PAGE 2

3 Assembly checklist Read through the instructions carefully before you begin. Make sure you have all the required tools. Never use power tools unless instructed. Identify and lay out all of the components before you begin assembly. Unless instructed, do not fully tighten screws until the item is fully assembled. Useful Information! Never use power tools unless specifically instructed. They can damage your components or hardware if used incorrectly.! The most common mistakes made during assembly are using the wrong hardware or getting components back to front.! Always use a soft surface (such as carpet or cardboard) when assembling your product to avoid scratching or damaging the surface of the product.! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be used in as they may not fit through a door once assembled.! Never use any glue until you are certain that the parts belong together.! Periodically check and re-tighten all fasteners. Check the product care label or website for product care instructions.! If you are having any difficulties assembling your product, missing any hardware or components please visit our website Help Centre for further assistance. PAGE 3

4 What you need to assemble the product Top Panel (P1) Side Panel DO NOT USE Additional Tools Required Flat head ; ; Hammer Divider Divider Shelf Panel Divider Shelf Panel (P4) Side Panel Divider Divider (P6) Shelf Panel Parts list Box 1: Top Panel (P1); 4 x Dividers ; 2 x Dividers (P6); Bottom Panel (P7); Box 2: 2 x Side Panels ; 2 x Shelf Panels ; Shelf Panel (P4); Hardware Pack Divider (P6) Bottom Panel (P7) 8 x Dowels (H1) 36 x Small Dowels () 24 x Cam Bolts () 24 x Cam Nuts () 8 x Long Screws (H5) 12 x Inside Hexagonal Bolts () 2 x Safety Strap Sets 1 x Allen Key (H7) 16 x Covers () 8 x Plastic Glides () 2 x Restraint Straps (H10) 2 x Screws (H11) 4 x Brackets (H12) PAGE 4

5 Step 1 12 x Cam Bolts () x 2 Attach 6 x Cam Bolts () into each Side Panel as shown. Step 2 8 x Cam Bolts () x 2 Attach 4 x Cam Bolts () into each Shelf Panel as shown. Step 3 2 x Cam Bolts () (P4) Attach 2 x Cam Bolts () into Shelf Panel (P4) as shown. PAGE 5

6 Step 4 4 x Small Dowels () 4 x Long Screws (H5) H5 H5 x 2 Insert 2 x Small Dowels () into the holes of Divider as shown. Attach Shelf Panel to Divider with 2 x Long Screws (H5). Tighten the screws with a. Repeat Step 4 for the other Divider and Shelf Panel. Step 5 4 x Small Dowels () 4 x Long Screws (H5) H5 H5 (P4) H5 H5 Insert 4 x Small Dowels () into the holes of Shelf Panel (P4) as shown. Attach Dividers to Shelf Panel (P4) with 4 x Long Screws (H5). Tighten the screws with a. PAGE 6

7 Step 6 10 x Small Dowels () 10 x Covers () 10 x Cam Nuts () Flat head This is how a cam nut works... The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt. (P4) (P6) (P6) TWO PEOPLE Insert 10 x Small Dowels () into the holes of Shelf Panels (P3, P4). Insert 10 x Cam Nuts () into the holes of Dividers (P5, P6). Rotate the cam nuts so the arrows point towards the incoming cam bolts. Push Dividers (P5, P6) into place and then tighten the cam nuts using a Flat head. Seal the holes with 10 x Covers () as shown. REQUIRED Step 7 (P4) 6 x Small Dowels () Flat head 6 x Cam Nuts () Insert 6 x Small Dowels () into the holes of Shelf Panels (P3, P4). Insert 6 x Cam Nuts () into the holes of Shelf Panels (P3, P4). Rotate the cam nuts so the arrows point towards the incoming cam bolts. Push Side Panel into place and then tighten the cam nuts. PAGE 7

8 Step 8 6 x Small Dowels () 6 x Cam Nuts () Flat head (P4) Insert 6 x Small Dowels () into the holes of Shelf Panels (P3, P4). Insert 6 x Cam Nuts () into the holes of Shelf Panels (P3, P4). Rotate the cam nuts so the arrows point towards the incoming cam bolts. Push Side Panel into place and then tighten the cam nuts. Step 9 2 x Cam Bolts () (P1) Attach 2 x Cam Bolts () into Top Panel (P1) as shown. PAGE 8

9 Step 10 (P1) H1 4 x Dowels (H1) 2 x Small Dowels () H1 2 x Cam Nuts () 2 x Covers () Flat head Insert 4 x Dowels (H1) into the holes of Side Panels. Insert 2 x Small Dowels () into the holes of Divider. Insert 2 x Cam Nuts () into the holes of Divider. Rotate the cam nuts so the arrows point towards the incoming cam bolts. Attach Top Panel (P1) to Side Panels and Divider. Tighten the cam nuts using a Flat head. Seal the holes with 2 x Covers () as shown. Step 11 H7 (P1) 4 x Inside Hexagonal Bolts () 1 x Allen Key (H7) 4 x Covers () Secure Top Panel (P1) to Side Panels with 4 x Inside Hexagonal Bolts () using an Allen Key (H7). Seal the holes with 4 x Covers () as shown. PAGE 9

10 Step 12 4 x Dowels (H1) 4 x Small Dowels () H1 8 x Inside Hexagonal Bolts () 1 x Allen Key (H7) (P6) H1 (P6) (P7) H7 Insert 4 x Dowels (H1) into the holes of Side Panels. Insert 4 x Small Dowels () into the holes of Dividers (P6). Attach Bottom Panel (P7) to Side Panels and Dividers (P6) with 8 x Inside Hexagonal Bolts () using an Allen Key (H7). 10mm Step 13 8 x Plastic Glides () Hammer (P7) Place glides 10mm from edge. Attach 8 x Plastic Glides () to the bottom of Bottom Panel (P7) with a Hammer. PAGE 10

11 Step 14 We strongly advise that you use the wall safety strap provided to prevent the unit toppling Seek advice from a qualified trades person on how to attach this safety strap to your specific wall. 2 x Restraint Straps (H10) 2 x Screws (H11) Wall 4 x Brackets (H12) H12 H11 Wall Screw H12 Wall Screw and Wall Plug which are not provided. Please use appropriate fixtures for your wall. (P1) Wall H12 H10 TWO PEOPLE REQUIRED Carefully turn the bookcase over to an upright position. Attach 2 x Brackets (H12) securely to back of Top panel (P1) with 2 x Screws (H11) through the smaller hole. Align the opposite wall bracket about 20mm lower than then the one attached to the bookcase so the bracket cant be seen. Using appropriate wall connection fixtures, secure the bracket to the wall and thread the restraint strap through it. Be careful not to over tighten the strap which would cause the unit to lean. PAGE 11

12 Recommended weight capacity for each shelf : 10KG. Job Complete! In the interest of our environment please dispose of all packaging thoughtfully. PAGE 12