Colonial Classic Bar

Transcription

1 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List A. Top B. Leaf Top C. Leg 4 pcs. For assembly see instructions in carton Home Styles Consumer Assistance: servicedesk@homestyles-furniture.com, ,

2 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List I. Shelf J. Stretcher D. Side Panel L. Door Hardware List E. Middle Panel M. Foot Rest 1 pc. F. Side Panel G. Front Panel H. Front Panel 2 pcs. K. Shelf 3 pcs. N. Drawer (Refer of the last page of instruction for steps to complete drawer assembly) Small Hex Wrench 35 pcs. (+6 extra) M3.5x25 Wood Screw (long) 8 pc. (+1 extra) Magnet M4x25 Machine Screw 2 pcs. Knob 2 pcs. Hex Wrench M6x10 Head Cap Bolt 2 pcs. (+1 extra) M6x12 Flat Head Cap Bolt 4 pcs. (+1 extra) Screw 35 pcs. (+2 extra) M3.5x12 Wood Screw(short) 6 pcs. (+1 extra) Adjustable Pin 12 pcs. (+1 extra) For assembly also need the following : Foot Rest Support 2 pcs. Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level Home Styles Consumer Assistance: servicedesk@homestyles-furniture.com, ,

3 Assembly Instruction 2 / 7 IMPORTANT * Do not tighten up all the screws until each part is properly assembled. * You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Use a soft cloth between these parts and the floor. * After assembly, item must be level to work properly. Use the included adjustable levelers to level. Screw A B D Screw E F Screw G I STEP 1 Insert Screws into the pre-drilled holes of Top (A), Base (B), Side Panels (D), (F), Middle Panel (E), Front Panel (G) and Shelf (I) (see Figure 1) Figure 1

4 Assembly Instruction 3 / 7 STEP 2 H Attach Front Panels (H) to Front Panel (G) using Cam Locks. (see Figure 2) G H STEP 3 Attach Side Panel (D) to Front Panel unit using s. Attach Shelf (I) to Side Panel (D) with s. Attach Middle Panel (E) to Shelf (I) with s. I Figure 2 E D

5 STEP 4 Attach Stretcher (J) to Middle Panel (E) with. Attach Side Panel (F) to unit with s. F J Assembly Instruction 4 / 7 STEP 5 Attach Base (B) to unit with Cam Locks. Attach Legs (C) to unit. (see Figure 3) C C B C C Figure 3

6 A Assembly Instruction 5 / 7 STEP 6 Turn the unit over to its upright position. Attach Top (A) to unit with s. Attach Magnet to middle panel with Wood Screws (short). (see Figure 4) Figure 4 Wood Screw (short) Magnet STEP 7 Figure 5 Figure 6 Slide Drawer (N) into position. Insert Adjustable Pins into side panels and middle panel at the desired level, then place Shelves (K) into position. Attach Door (L) to side panel by sliding the door lift hinges into the side panel lift hinges. (see Figure 5) L N Assemble Knob to Door (L) with Machine Screw. (see Figure 6) Adjustable Pin K K K

7 STEP 8 Assembly Instruction 6 / 7 Insert Foot Rest (M) into Foot Rest Supports. Attach Foot Rest Supports to unit with Flat Head Cap Bolts and tighten With Hex Wrench. (see Figure 7) Attach Foot Rest (M) to Foot Rest Supports with Head Cap Bolts leaving same amount of Foot Rest (M) protruding on outside of the outer Foot Rest Supports. (see Figure 8 ) M Flat Head Cap Bolt Figure 7 Flat Head Cap Bolt Figure 8 Flat Head Cap Bolt STEP 9 To level the unit, adjust the adjustable levelers on the bottom of unit. (see Figure 9) Note: Unit must be level to work properly. Figure 9

8 Drawer (N) Assembly Instruction 7 / 7 N3 N1 Figure 1 STEP 1 Attach N1 to N2 and N4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. Attach N2 to N3 and N4 using long wood screws (4X), tighten halfway. (see Figure 1) N3 N2 N5 N1 N4 MAKE SURE ROLLER IS ON THE BACK Figure 2 N5 N3 N4 N1 STEP 2 Slide N5 into the grooves in N3 and N4. Be sure to push N5 all the way forward so it meets N1. (see Figure 2) N2 N4 Figure 3 STEP 3 Insert short wood screws (4X) into the pre-drilled holes in N5 and tighten. (see Figure 3) Part List Figure 4 STEP 4 Assemble Pull Handle with machine screws. (see Figure 4) Tighten all screws used in drawer assembly. N1. N2. N3. Front Part Back Part Side Part 1 pc. N4 Side Part N5. Base Part

9