SEQUEL 6021 EXECUTIVE DESK

Transcription

1 SQUL 6021 roduct Registration Registering your new BI product allows us to send you important product updates, service information and helpful hints related to your BI products. Register today and you will be entered to win free a BINK table from BI. lacement and aintenance Sequel ffice furniture is designed for indoor use on level floors. Clean glass with glass cleaner, and steel parts and wood veneer with a moist cloth. Your Sequel ffice furniture is engineered for easy assembly. Carefully follow this procedure to prevent any damage. o not use power tools for assembly of this product. Step 1 Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. or missing hardware pieces, please contact BI Customer Service at. or all other concerns, please contact your BI retailer. C - Wire anagement Lid x 1 J 4mm Hex Wrench x 1 K 1/4-20 x 12mm Screw x 3 L 1/4-20 x 32mm Screw x 6 Barrel Nut x 4 N 1/4-20 x 15mm Screw x 4 1/4-20 x 58mm Screw x 6 1/4-20 x 87mm Screw x 2 Q Center rawer Liner x 1 R Side rawer Liner x 2 S Rubber Stem Bumper x 5 B - Top lass x 1 T 8/32 x 37mm Screw x 4 - odesty anel x 1 - rawer ssembly x 1 - Wire anagement Trough x 1 H - Removable Side anel x 2 * Remove for ssembly H - Removable Side anel x 2 * Remove for ssembly - Left Leg x 1 - Right Leg x 1 I - lide x 4 esigned by atthew Weatherly. These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BI are trademarks of Becker esigned, Inc. ll rights reserved. 2016, BI ade in Taiwan V10

2 Step 2 ligning the Colored ots on the same side, attach Wire anagement Trough () to odesty anel () using Screw (K) and Hex Wrench (J). Keep screws loose until Step 7. K x 3 Colored ots Step 3 atch Colored ot on Right Leg () with Colored ot on odesty anel ssembly and attach using Screws (L) and Hex Wrench (J). Keep screws loose until Step 5. Repeat to attach Left Leg () to odesty anel ssembly. Install lides (I) to the bottom of Legs (, ). With the help of another person, turn desk upright onto its base. I x 4 L Colored ot L x 6 2

3 Step 4 Insert Barrel Nut () into holes of odesty anel () with the elongated slot sitting horizontally, and secure with Screw () through side of Legs (, ). Keep screws loose until Step 5. longated slot in Barrel Nut () aligns with Screw () Step 5 Secure rawer ssembly () to Leg ssembly using Screw (N) and Hex Wrench (J). Insert Barrel Nut () into holes of odesty anel () with the elongated slot sitting vertically, and secure with Screw () through top of rawer ssembly (). ully tighten all Screws that have been installed in previous steps using Hex Wrench (J). N x 4 N N longated slot in Barrel Nut () aligns with Screw () 3

4 Step 6 Install Rubber Stem Bumpers (S) in the 5 holes shown below. With the grippy side facing down, insert Center rawer Liner (Q) into the center drawer and Side rawer Liners (R) into both side drawers. S x 5 Q x 1 R x 2 Step 7 With the help of another person gently lower Top lass (B) onto rawer ssembly () and fasten into place using Screw () and Hex Wrench (J). NT VRTIHTN! B x 4 4

5 Step 8 lace Wire anagement Lid (C) into opening in Top lass (B). ttach Removable Side anels (H) to Legs (,) using Screws (T) (and a hillips screwdriver) ensuring the top edge of the Side anel (H) sits against the top inside edge of Leg (,). Screws (T) are not structural. o not overtighten. C T x 4 H H Step 9 lace C power strip/surge protector (not included) into wire anagement Trough (). 5