SLOANE GREY/MAHOGANY LEANING WINE BAR

Transcription

1 SLONE GREY/MHOGNY LENING WINE R SSEMLY HRDWRE 8 - wood dowels 10- small bolts 4 - large phillips bolts 4 - plates 1 - drawer sper 2 - large allen bolts MENDING HRDWRE 2 - connecting plates 4 - medium screws MOUNTING HRDWRE Missing hardware? Please call for replacements. Thank you for purchasing the Sloane Grey/Mahogany Leaning Wine ar. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. s you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. Note: 2 people are required to safely assemble this product. 1 - small screw 1 - large screw TOOLS REQUIRED large allen wrench (included) small allen wrench (included) 2 - wall fittings 1 - wall strap 1 - plastic anchor phillips head screwdriver COMPONENTS OX 1 COMPONENTS OX back 2 - side posts (1 left, 1 right) wine cabinet NOTE: pull pre-attached to back of drawer front Page 1 of 5

2 SLONE GREY/MHOGNY LENING WINE R OTTOM 1 Insert 4 wood dowels into each and s as shown. 2 ) Fit dowels of s into corresponding holes of right post as shown. Secure each with 1 large phillips bolt and 1 plate, using a phillips head screwdriver. right post ) Position,, and wine cabinet as shown. ttach each to post with 1 small bolt. ttach wine cabinet to post with 3 small bolts. Secure all bolts with an large allen wrench. wine cabinet plate long bolt Page 2 of 5

3 SLONE GREY/MHOGNY LENING WINE R wine cabinet left post 3 ) Fit dowels of s into corresponding holes of left post as shown. Secure each with 1 large phillips bolt and 1 plate, using a phillips head screwdriver. ) Position left post with,, and wine cabinet as shown. ttach each to post with 1 small bolt. ttach wine cabinet to post with 3 small bolts. Secure all bolts with alarge allen wrench. 4 There are 2 back orientations for this assembly. Placement - walls without base moldings. Placement - walls with base moldings. Please determine which placement is appropriate to your wall. ttach back to unit with 2 large allen bolts as shown. Secure bolts with a small allen wrench. With the assistance of another adult, carefully position unit upright. back bolt hole SIDE VIEW DETIL media stand assembly bolt hole back WLL WLL small allen wrench 1" base molding Page 3 of 5

4 SLONE GREY/MHOGNY LENING WINE R 5 ) Remove drawer from wine cabinet. With a screwdriver, detach pre-assembled pull from back of drawer front. ttach pull to front of drawer front with 2 pull screws as shown. Secure screws with a screwdriver. drawer pull screws ) Insert drawer assembly half-way and insert drawer sper into wine cabinet as shown. Turn drawer sper clockwise to secure. C) t this point, fully insert drawer assembly into wine cabinet. ssembly is now complete. pull C CLENING ND CRE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer. drawer sper F wall strap C plastic anchor D large screw wall fitting & small screw NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store. WLL WLL MOUNTING INSTRUCTIONS For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. ) ttach 1 wall fitting to assembled unit as shown, using 1 small screw. ) Determine the final location of shelving unit. Mark position on the wall, approximately 2" below the bracket mounted to the back of the unit. C) Drill a pilot hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) ttach the wall fitting to the wall by inserting 1 large screw through the wall fitting and into the plastic anchor in the wall. E) Place the unit so the wall fitting on the back edge is aligned with the wall fitting on wall. F) Lace one end of the wall strap through both fittings, and into the other end of the strap. G) Pull the strap tightly until secure. Wall mounting assembly is now complete. Page 4 of 5

5 SLONE GREY/MHOGNY LENING WINE R MULTIPLE LENING SHELVES/WINE R SSEMLY If you purchased multiple leaning items, it is suggested that every two or more units be secured together. s shown, connect units with 2 connecting plates. ttach each plate with 2 medium screws and secure with a screwdriver. Repeat steps for each additional leaning unit. Made in Indonesia- r01 Customer Service Page 5 of 5