Installation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
|
|
- Ashley Martin
- 5 years ago
- Views:
Transcription
1 Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load apacity: 200 lb (91 kg)
2 Read instruction sheet before you start installation and assembly. Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at This product should only be installed by a qualified professional. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum UL Load apacity of 200 lb (91 kg). Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal studs (contact customer care). Metal stud installation is not UL evaluated. If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended. lways use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws and nuts firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. IMPORTNT! ertain types of walls require additional mounting hardware... WLL ONSTRUTION Wood Stud, Wood Beam oncrete Metal stud Other or unsure? DDITIONL HRDWRE REQUIRED none none WSP716, WSP716-S, WSP724, or WSP724-S ontact ustomer are IMPORTNT! Turn to the appropriate page for your wall installation. Installations: To Wood Stud Walls... page 4 To oncrete Walls... page 5 Tools Needed for ssembly stud finder ("edge to edge" stud finder is recommended) drill 7/32" drill bit for wood studs 5/16" masonry drill bit for concrete 7/16" socket wrench with extension (recommended) level phillips screwdriver 3/4" open-end wrench ccessories External Wall Plate (WSP716, WSP716-S, WSP724, WSP724-S) (Metal Stud not evaluated by UL)
3 Parts List Before you start make sure all parts listed are included with your product. PLV 70 PLV 70-S DESRIPTION QTY. PRT # PRT # wall plate B tilt-roll assembly arm assembly D wall support arm axle E vinyl trim M10 x 1.5 x 15 mm screw bolt G.505 x.75 x.062" nylon washer H tilt adjustment knob I carriage bolt 3/8"-16 x 3.25" J x 2 x.062" delrin washer K #8-32 x.375" socket head cap screw L plastic finishing cap M holding pin N retainer plug O 5/16 x 3" wood screw P.250 x 1 x.068" washer Q 9/64" allen wrench R cable management clips S cable tie T 36" polyester mesh sleeve U 6 mm allen wrench W anchor B H D E G I J K M N L R S W O P Some parts may appear slightly different than illustrated. Q U T
4 Installation to Wood Stud Wall Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal studs (contact customer care). Metal stud installation is not UL evaluated. Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. Never exceed the Maximum UL Load apacity of 200 lb (91 kg). 1 Wall plate () can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud s center. Place wall plate on wall as a template. The top mounting slots should be located.43" below the desired screen center. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it using eight 5/16 x 3" wood screws (O) and washers (P). Skip to step 2 on page 6. Never mount this product to metal studs without the required accessory. O P
5 Installation to oncrete Wall oncrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum UL Load apacity of 200 lb (91 kg). IMPORTNT! oncrete must be 2000 psi density minimum. 1 concrete surface 1 Use wall plate (), making sure that it is level, as a template to mark holes. The top mounting slots should be located.43" below the desired screen center. Use the masonry bit to drill 5/16" (8 mm) dia. holes to a minimum depth of 3" (76 mm). Insert anchors (W) in holes flush with wall as shown (right). Place wall plate () over anchors (W) and secure with 5/16 x 3" wood screws (O) and washers (P). Drill hole(s) and insert anchor(s) (W) 2 mounting plate W Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. Never tighten in excess of 80 in lb (9 N.M.). 3 W Place plate over anchor(s) (W) and secure with screw(s)(o) lways attach concrete expansion anchors directly to load-bearing concrete. Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. If plaster/ drywall is thicker than 5/8", custom fasteners must be supplied by installer (Not UL evaluated). Tighten all fasteners O P W INORRET ORRET UTWY VIEW mounting plate plaster/ dry wall concrete mounting plate plaster/ dry wall concrete
6 If you are uncertain that product is properly installed, call customer care Note: There are three mounting positions. The center position is shown right. rm assemblies must be mounted with one mounting hole separating them. Slide washers (J) over wall support arm axles (D). Next, insert plastic caps (N) into axles. Then, insert holding pins (M) into axles. See detail 1. Place arm assembly () with washers (J) into wall plate (). Insert axle assemblies shown in detail 1 through wall plate (), arm assembly (), and washers (J). Lock axles in place by aligning holding pins (M) with notches shown in detail 2. NOTH M N J D DETIL Insert socket cap screws (K) into hole at bottom of wall support arm axles (D) as shown in detail 3. Tighten screw using 9/64" allen wrench (Q). DETIL 2 3 Note: it of axles (D) into wall plate () and arm assembly () will be tight. Gently tap into place with a hammer if necessary. To route cables through cord management channels: Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables. 3 J K D DETIL 3 To route cables using cable management clips: Snap eight cable management clips (R) into both swing arms () as shown in figure 3.2. able ties (S) are used with clips for cord management. 3-1 Pull cords through cord management channels, leaving enough slack to allow full range of movement for swing arm assembly () as shown if figure 3.1. T 3-1 Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables. S ORD MNGEMENT HNNEL fig 3.1 R fig 3.2
7 4 4-1 ttach two pieces of vinyl trim (E) to wall plate (). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (). Insert one finishing cap (L) into each unused hole of wall plate (). SWIVEL BOX E L E NOTE: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is not used with this product. 5 Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B). ttach tilt-roll assembly to adapter bracket with four M10 socket screws (). Tighten screws using 6 mm allen wrench (U). Note: dapter bracket (not UL evaluated, sold separately) will vary in size and style. UTION GENERI DPTER BRKET Do not overtighten screws! Overtightening may hinder roll option. B I
8 Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. 6 Insert two M10 screws () into swivel box on arm assembly () as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX.25" Hook tilt-roll assembly (B) onto M10 screws (). Insert carriage bolt (I) into slot of swivel box as shown in figure 6.1. Install nylon washer (G) and tilt adjustment knob (H). Install remaining two M10 screws () as shown in figure 6.2. HND TIGHTEN all four M10 screws to allow for tilt adjustment. Remove tape from carriage bolt (I). or tilt adjustment, gently push back on the top of plasma to relieve pressure on knob. djust tilt to desired position and tighten tilt adjustment knob (H), then securely tighten all four M10 screws () using 6 mm allen wrench (U). B I G H UTION fter tilt is adjusted, all fasteners must be tightened. ailure to do so will result in damage to the mount. I B SWIVEL BOX fig 6.1 fig 6.2 dapter bracket not shown for clarity. dapter bracket not shown for clarity.
9 7 Depending on the specific size & weight of the plasma, articulating swing arm may be angled at different 7-1 positions, causing plasma to appear to lean sideways at different articulating positions. Tilt roll assembly (B) allows plasma to be manually adjusted, so plasma can be horizontal at all positions. To adjust, gently rotate plasma by hand to desired position. If it is too difficult to adjust roll of plasma, loosen screws shown in figure 7.1 using a phillips screwdriver. IMPORTNT! Do not loosen or tighten screws more than 1/8 turn. RTIULTING RM PLSM ROLL DJUSTMENT SREWS fig Position of screen may be adjusted vertically up to.79" in each direction by doing the following: To raise screen, turn hex nut shown in figure 8.1 clockwise with 3/4" open-end wrench (not provided). To lower screen, turn hex nut shown in figure 8.1 counterclockwise with 3/4" open-end wrench (not provided). HEX NUT fig 8.1
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 65" Plasma Screens. Models: PLAV70, PLAV70-S
Installation and ssembly - Universal rticulating Swivel Double-rm for 42" - 65" Plasma Screens Models: PLV70, PLV70-S Max UL Load apacity: 200 lb (91 kg) 2300 White Oak ircle urora, Il 60502 (800) 865-2112
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInstallation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays
Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationModels: PLAV70-UNL, PLAV70-UNLP. Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 95" Plasma Screens Models: PLAV70-UNL, PLAV70-UNLP Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle Aurora, Il 60502
More informationInstallation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays
Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read
More informationInstallation and Assembly: Full Service Video Wall Mount
Installation and Assembly: Full Service Video Wall Mount Model: DS-VW765-LAND Max UL Load Capacity: 125 lb (57 kg) 1 of 12 ISSUED: 05-13-11 SHEET #: 145-9011-5 05-21-12 Note: Read entire instruction sheet
More informationInstallation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400
Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)
More informationInstallation and Assembly: Projector Ceiling/Wall Mount
Installation and ssembly: Projector Ceiling/Wall Mount Models:PRG-EX, PRG-EX-S, PRG-EX-W PRG-EXB, PRG-EXB-S, PRG-EXB-W PRG-EXC, PRG-EXC-S, PRG-EXC-W R This product is intended for use with UL Listed products
More informationInstallation and Assembly: Wallmount for CPA100 and Whiteboard
Installation and ssembly: Wallmount for CP100 and Whiteboard Model: 100IWBMOUNT Maximum Load Capacity for Screen: 53 lb (24 kg) Maximum Load Capacity for Projector : 13.5 lb (6 kg) 1 of 16 Visit 3215 the
More informationInstallation and Assembly Manual: Vector Pro II
Installation and ssembly Manual: Vector Pro II Models: PJF2-UNV, PJF2-UNV-S R This product is intended for use with U isted products and must be installed by a qualified professional installer. Maximum
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationNEC Display Solutions of America, Inc.
NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NP-M332XS, NP-M352WS, NP-M282X, NP-M283X, NP-M322X, NP-M323X, NP-M322W, NP-M323W, NP- M363X, NP-M363W, NP-M402X,
More informationInstallation and Assembly: Universal Projector Wall Arm
nstallation and ssembly: Universal Projector Wall rm Model: SP-WLLRM-01 SP-CEL-UNV (sold separately) Max Load Capacity:35 lb (15.8 kg) Note: Read entire instruction sheet before you start installation
More informationNEC Display Solutions of America, Inc.
NEC Display Solutions of merica, Inc. Installation and ssembly Manual: Custom Ceiling Mount for NEC NP400, NP500, NP500W, and NP600 Projectors Model: NP600CM Maximum Load Capacity: 50 lb (22.7 kg) Features:
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product
More informationInstallation and Assembly: Projector Ceiling/Wall Mount
Installation and ssembly: Projector eiling/wall Mount Model# Max UL Load apacity EX, EX-S, EX-W, EX, EX-S, used with PRS projector mount 25 lb (11.3 kg) EX-W, EX, EX-S, EX-W used with PRG projector mount
More informationInstallation and Assembly: Universal Projector Wall Arm
Installation and ssembly: Universal Projector Wall rm Models: PST-2955, PST-2955-W, PST-2955, PST-2955-W Max UL Load Capacity: 35 lb (5.8 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-22 Fax: (800)
More informationInstallation and Assembly: Mount - Wall/Ceiling Mount
Installation and ssembly: Mount - Wall/Ceiling Mount Model: DST360 Max oad Capacity: 150 lb (68. kg) 3215 W. North ve. Melrose Park, I 60160 (800) 729-0307 or (708) 865-8870 ax: (708) 865-2941 www.peerlessmounts.com
More informationINSTALLATION GUIDE Ceiling TV Mount MHP-52
ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and
More informationInstallation and Assembly: Ceiling mount for LCD screens up to 29"
Installation and Assembly: Ceiling mount for LC screens up to 29" Models: LCC 18, LCC 18-S, LCC 36, LCC 36-S Patent Pending Features: Comes in two adjustable height ranges (in 1" increments): 18"-30" and
More informationInstallation and Assembly: Ceiling mount for LCD screens up to 29"
Installation and Assembly: eiling mount for L screens up to 29" Models: L18-, L18-S, L36-, L36-S Features: omes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48" -5 to +20 adjustable
More informationInstallation and Assembly: DUKANE PROJECTOR SHORT THROW WALL ARM
Installation and Assembly: DUKANE POJETO SHOT THOW WALL AM Model: UST-WALLAM3 POJETO POSITION FO 60" - 70" SEEN SIZE POJETO POSITION FO 70" - 100" SEEN SIZE 430-User Guide UST-WALLAM3-00 Do not begin to
More informationInstallation and Assembly:
Installation and ssembly: Model: DS508 os pd For SHPD installations, please contact Peerless Customer Service for a copy of the P. Maximum Load Capacity: 200 lb (90.7 kg) 2300 White ak Circle urora, IL
More informationInstallation and Assembly Manual: PRS Series Projector Mount
Installation and ssembly Manual: PRS Series Projector Mount Models: PRS-1, PRS-1S, PRS-1W Features: ImageLock TM alignment prevents picture sag or drift Exclusive aluminum track quick release C U L US
More informationWARNING. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
All-in-one Projector Adapter Plate I5300 series, I5500 series, and SP8602 series Model: SP-CEIL-ISTALL Maximum Load Capacity: 50 lbs/22 kg Read all instructions before you start installation and assembly.
More informationInstallation and Assembly Manual: PRS, RTR Series Projector Mount
Installation and ssembly Manual: PS, T Series Projector Mount Models: PS-UNV, PS-UNV-S, PS-UNV-W PS-UNVP, PS-UNVP-S, PS-UNVP-W T-UNB, T-UNS, T-UNW This product is intended for use with UL Listed products
More informationSM-RAZOR-ART2-L / SM-RAZOR-ART2-XL
SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationINSTALLATION GUIDE. Flat Panel Arm Mount MHA-800. VESA 500x800 compatible. Support 42" to 63" Screens Max Load Capacity: 200 lbs (91 kg)
INSTALLATION GUIDE Flat Panel Arm ount HA-800 Support 2" to 63" Screens ax Load Capacity: 200 lbs (91 kg) VESA 500x800 compatible Be sure to read this entire manual thoroughly and you fully understand
More informationINSTALLATION GUIDE. Flat Panel Arm Mount MHA-72. VESA 750x850 compatible. Support 52" to 72" Screens Max Load Capacity: 300 lbs (136 kg)
INSTALLATION GUIDE Flat Panel Arm Mount MHA-72 Support 52" to 72" Screens Max Load Capacity: 300 lbs (136 kg) VESA 750x850 compatible Note: Read entire instruction sheet before you start installation and
More informationINSTALLATION GUIDE. Flat Panel Arm Mount MLA100-L. VESA 100x100 compatible. Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg)
INSTALLATION GUIDE Flat Panel Arm Mount MLA100-L Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg) VESA 100x100 compatible Note: Read entire instruction sheet before you start installation and
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More informationINSTALLATION GUIDE. Flat Panel Arm Mount BTAR2/37. VESA 200x200 compatible. Support 24" to 37" Screens Max Load Capacity: 80 lbs (36 kg)
INSTALLATION GUIDE Flat Panel Arm Mount BTAR2/37 Support 2" to 37" Screens Max Load Capacity: 80 lbs (36 kg) VESA 200x200 compatible Note: Read entire instruction sheet before you start installation and
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP 850, SP 850P, SP 850-S, SP 850P-S Max Load Capacity: 150 lb (68 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or
More informationFlat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold
FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination
More informationINSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT
INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment
More informationSB-WM-ART2-L-BL SB-WM-ART2-XL-BL
SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier
More informationWARNING. Installation and Assembly - Vision Point Height Adjustable Desktop Mount with Stationary Base for LCD Screens
Installation and Assembly - Vision Point Height Adjustable Desktop Mount with Stationary Base for LD Screens IMPORTANT! Read entire instruction sheet before you start installation and assembly. Models:
More informationInstalling flat panels on the MPL15 wall mount
Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape
More informationInstallation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS
Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationSM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL
SM-RAZOR-F-M/L/XL Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationEXTENSION COLUMN (SOLD SEPARATELY)
nstallation and ssembly - Solid Point Plasma eiling Mount Model: PL 1 Read instruction sheet before you start installation and assembly. Maximum Load apacity: 300 lb (136 kg) WRNNG Failure to install M5
More informationAssembly Instructions for Model: VMDD26
Assembly Instructions for Model: VM26 Thank you for choosing a Sanus Systems Vision Mount wall mount. The VM26 is designed to mount up to 63 lat panel televisions weighing up to 175 lb. to a vertical wall.
More informationInstallation & Assembly: Two Piece Suspended Ceiling Plate
Installation & ssembly: Two Piece Suspended Ceiling Plate Model: CMJ453 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
nstallation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1M, SR560M R This product is UL Listed. t must be installed by a qualified professional installer. Max UL Load Capacity: 150 lb (68 kg)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationInstallation and Assembly - Vision Point LCD Screen Pedestal Stand - 75/100 mm Adapter Plate
Installation and ssembly - Vision Point CD Screen Pedestal Stand - 75/100 mm dapter Plate Model: CS 100, CS 100S Read instruction sheet before you start installation and assembly. Maximum oad Capacity:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInstallation & Assembly: Suspended Ceiling Kit
Installation & ssembly: Suspended Ceiling Kit Model: CMJ450 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500
More informationSmall Above Fireplace Pull-Down Full-Motion TV Wall Mount
Small Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 33123 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...
More informationAssembly Instructions for Model: MF110
Assembly Instructions for Model: MF110 Thank you for choosing a Sanus Systems VisionMount wall mount. The MF110 is designed to mount LCD flat panels with VESA (Video Electronics Standards Association)
More information19 to 39 TV WALL MOUNT - FULL MOTION
19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5
More informationMONOPRICE. Above Fireplace Pull-Down Full-Motion TV Wall Mount. User's Manual P/N 27773
MONOPRICE Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 27773 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...
More informationMM750 Installation Instructions
MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series
INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series
More informationINSTALLATION GUIDE. Embedded TV Wall Mount MHAI-700. VESA 500x800 compatible. Support 42" to 63" Screens Max Load Capacity: 200 lbs (91 kg)
INSTALLATION GUIDE Embedded TV Wall Mount MHAI-700 Support 2" to 63" Screens Max Load apacity: 200 lbs (91 kg) VESA 500x800 compatible Note: Read entire instruction sheet before you start installation
More informationModel Name: ROY6609B. Installation Instructions. Hardware Bags. Imp o r t a n t N o t e s. Component Checklist P.1
P.1 Imp o r t a n t N o t e s Installation Instructions Model Name: ROY6609B I n s t al l a t i o n w il l r e q u i r e a m i n i m u m o f t w o p e o p l e. U n d e r n o c i r c u m s ta n c e s s
More informationPFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS
Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationParts List D E. Installation and Assembly- Encore Projector Mount Protected by U.S. Patent No. 6,042,068. Model: PJRL411
nstallation and ssembly- ncore Projector Mount Protected by U.S. Patent No. 6,042,068 Model: PRL4 MPORTNT! Read entire instruction sheet before you start installation and assembly. WRNN! nstaller must
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationModel : TLX-350FM. TV Mount Installation Guide
Model : TLX-350FM TV Mount Installation Guide Thank you for choosing Stanley the hardware of choice for Architects, Contractors, and Home Owners for its quality, performance and dependability. Following
More informationAssembly Instructions for Model: VMPL3
Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationInstallation and Assembly: Wireless Articulating Arm Wall Mount for 42" to 60" Flat Panel Displays
Installation and Assembly: Wireless Articulating Arm Wall Mount for 42" to 60" Flat Panel Displays Model: WL-SA761PU-200 Maximum Load Capacity: 130 lbs (59 kg) 2300 White Oak Circle Aurora, Il 60502 (800)
More informationArticulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series)
P Articulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series) Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationPFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstallation and Assembly: Flat-Panel Base Lock-Down Kit for Samsung Display Models
Installation and ssembly: Flat-Panel Base Lock-own Kit for Samsung isplay Models Models: HLG452-SM, HLG452-SM-Q10 Maximum isplay Size: 100 lb (45.35 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationLC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60
More information4 BAY Low Profile-Dual Displays WALL MOUNT CABINET
D1/347M2 SSEMLY INSTRUTIONS 4 Y Low Profile-Dual Displays WLL MOUNT INET TIP HZRD WRNING! abinet must be affixed to wall. For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions
More information/B INSTALLATION MANUAL
02-001127/B INSTALLATION MANUAL LEVITATION TV MOUNT UNIVERSAL TV MOUNT FOR 55"-75" PANEL TV'S 100 POUND MAXIMUM WEIGHT IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS - PLEASE READ ENTIRE MANUAL
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationQLF215 INSTRUCTION MANUAL
QLF215 INSTRUCTION MANUAL We ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We re ready to help! 1 2 3 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More informationINSTRUCTION MANUAL LCD TV BRACKET WM-3968
INSTRUCTION MANUAL LCD TV BRACKET WM-3968 DEAR CUSTOMER In order to achieve the best performance of your product, please read this instruction manual carefully before using, and keep it for future reference.
More informationPHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns
PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns Features: Durable high quality gloss black baked on powder coat finish Fits
More informationInstallation and Assembly: Adjustable Extension Column (Pipe) 8" - 11"
Installation and ssembly: djustable Extension Column (Pipe) 8" - 11" Model: ELPMBC01 R This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 500
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationSapper XYZ Monitor Arm Installation Instructions
9/5/2012 Sapper XYZ Monitor rm Installation Instructions 5900800 Step 1: ttach Mount to Work Surface Two-Piece Table lamp and eep Table lamp llen wrenches (in inches): lamp lower to upper jaw 5/32 () lamp
More information/A INSTALLATION MANUAL
02-001118/A INSTALLATION MANUAL LEVITATION TV MOUNT UNIVERSAL TV MOUNT FOR 55"-85" PANEL TV'S 125 POUND MAXIMUM WEIGHT IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS - PLEASE READ ENTIRE MANUAL
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
Installation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1G, SR560G R This product is U isted. It must be installed by a qualified professional installer. Max U oad Capacity: 150 lb (68 kg) screen
More informationINSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series
INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option
More informationPFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More information