BUTTERFLY VALVES VIC SERIES. High Performance for a Wide Range of Applications. of applications. percent leakage capability at each valve s

Size: px

Start display at page:

Download "BUTTERFLY VALVES VIC SERIES. High Performance for a Wide Range of Applications. of applications. percent leakage capability at each valve s"

Adam Atkins
5 years ago
Views:

1 UTTRLY VLVS VI SRIS High Performance for a Wide Range of pplications rooved butterfl y valves meet a wide range of applications. dvanced seat and disc design provides zero percent leakage capability at each valve s rated temperature/pressure while maintaining a low seating torque.

2 utterfly Valve Nomenclature 6 50 VI SY2-24 MT 6 = 2-way 7 = 3-way Valve Size 50 = 2 65 = 2½ 80 = = = = = = = 12 Trim Material -VI = uctile Iron rooved nd ody, Nickel oated uctile Iron isc, 0% Leakage up to 200 psi ctuator Type Non-Spring Return M(X) M... N4(H) M(X) R(X) R... N4(H) SY lectronic ail-safe K Spring Return Power Supply -24 = 24 V/ -110 = 110/120 V -120 = 120 V -230 = 230 V UP = V or V ontrol -3-X1 = On/Off, loating Point MT or MT-X1 = Multi-unction Technology -S = uilt-in uxiliary Switch N4 = NM 4/4X N4H = NM 4 with Heater Ordering xample 1 hoose the valve actuator combination. 650H+SY2-24MT 2 2-way Preference Specify preference or confi guration. Set-Up 3 +NO or MT orders only - select programming code (consult factory) +Tagging (if needed) 3-way onfiguration 4 oes order require tagging? Spring Return 2 Pos. Modulating N NO NO/O N/ NO/ N/O Set Up Required ield Logic etermines Normal Position (Normally losed) 0.5 V/2 V/4m = losed (Normally Open) 0.5 V/2V/4m = Open (Normally Open/ail Open) ield Logic etermines Normal Position Spring ails Valve OPN (Normally losed/ail losed) ield Logic etermines Normal Position Spring ails Valve LOS (Normally Open/ail losed) 0.5 V/2V/4m = Open Spring ails Valve LOS (Normally losed/ail Open) 0.5 V/2V/4m = losed Spring ails Valve OPN Spring Return 2 Pos. Modulating Modulating 2 Pos. Specify low Pattern [see pg.19-4, 19-5] Specify low Pattern [see pg. 19-4, 19-5] No Set Up Required ield Logic etermines Normal Position Master (ctuated) Valve N (Normally losed) 0.5 V/2 V/4m = losed Master (ctuated) Valve NO (Normally Open) 0.5 V/2V/4m = Open NO/O (Normally Open/ail Open) ield Logic etermines Normal Position Spring ails Master Valve OPN N/ (Normally losed/ail losed) ield Logic etermines Normal Position Spring ails Master Valve LOS NO/O (Normally Open/ail Open) 0.5 V/2V/4m = Master Valve Open Spring ails Master Valve OPN NO/ (Normally Open/ail losed) 0.5 V/2V/4m = Maser Valve Open Spring ails Master Valve LOS N/O (Normally losed/ail Open) 0.5 V/2 V/4m = Master Valve losed Spring ails Master Valve OPN N/ (Normally losed/ail losed) 0.5 V/2 V/4m = Master Valve losed Spring ails Master Valve LOS Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) xample: hiller 1 3rd loor ast Part number for tagging: omplete Ordering xample: 650H+SY2-24MT+NO + onsult factory

ontrol Valve Product Range rooved utterfly Valve Product Range 2-way Suitable ctuators Valve Nominal Size Type Non-Spring Return Spring Return lectronic ail-safe v 90 v 60 IN N [mm] 2-way 115 2 50

3 ontrol Valve Product Range rooved utterfly Valve Product Range 2-way Suitable ctuators Valve Nominal Size Type Non-Spring Return Spring Return lectronic ail-safe v 90 v 60 IN N [mm] 2-way VI ½ VI VI VI VI VI VI VI VI M Series M Series R Series SY Series Series K Mode of Operation rooved butterfly valves are designed for body pressures ranging from full vacuum to 300 psi and for bi-directional, dead end services to full body pressure. The valve patented seat design ensures full 0 sealing. The pressureenhanced seat compresses to form a larger seating area as the pressure increases. Valve construction and performance meet and exceed MSS-SP-67 requirements. Product eatures The unique single offset disc and seat design ensures positive valve seating while maintaining low seating torque. Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. v 90 v 60 3-way Valve Nominal Size IN N [mm] Type 3-way VI ½ VI VI VI VI VI VI VI VI M Suitable ctuators Non-Spring Return M Series SY Series Spring Return ctuator Specifications ontrol type Manual override lectrical connection Valve Specifications Service low characteristic on/off, fl oating point, modulating, 2-10 V, multi-function technology (MT) all models 3 ft. [1 m] cable terminal block chilled, hot water, 60% glycol 6 modifi ed equal percentage 7 modifi ed linear Sizes 2 to 12 nd fi tting grooved NSI/WW (606) Materials* ody ductile iron STM 5, grade ody fi nish black alkyd enamel isc electrolysis nickel coated ductile iron Shaft 416 stainless steel Seat PM earings fi berglass with T lining Media temp. range -20 to +250 [-30 to +120 ] ody pressure rating 300 psi lose-off pressure 200 psi (for most combinations) Rangeability 100:1 Maximum velocity Leakage 0% 20 PS *VI 300 Masterseal is manufactured by Victaulic ompany US N LTIN MRI 3

4 eatures and enefits VI Victaulic utterfly Valves elimo VI.. Series Victaulic utterfl y Valves are designed for pressure ranging from vacuum to 300psi and for dead end services Valve esign eatures The valve features a patented seat design that assures full 0 sealing. The pressure enhanced seat compresses to form a larger seating area as the pressure increases. The seat design also contributes to low breakaway torque of the valve. Valves have PM seats that are L classifi ed to NSI/NS 61. The disc is ductile iron, conforming to STM -5, grade with electrolysis nickel coating conforming to STM Stem is 416 stainless steel conforming to STM to full working pressure. ll Vitaulic valves are supplied in grooved style body design. RIV HU esigned to accept nearly all types of actuation. ISO 5211 MOUNTIN LN ccepts ISO standard actuators. 2-8 / mm are fl ange size / mm are fl ange size 10. STM SLS Prevents leakage of media. ROOV N OY Reduces the weight of the valve and makes it easier to install. UPPR N LOWR STM RINS Helps maintain constant low torque values for the life of the valve. THRML RRIR Reduces condensation on gear operators when installed in chilled water applications. SL RTRI Patented seal cartridge houses stem seals. STM lowout proof design utilizing stainless steel. RTNULR RIV Positive rectangular drive eliminates fastners in the flow stream. esign prevents replacement errors. ST Patented pressure enhanced rubber seat design. IS lectroless nickel coated ductile iron. Optional: luminum ronze Stainless Steel Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

5 VI Series utterfly Valves Standard ctuation (verage ssembly Weights) 2-WY 3-WY NON-SPRIN RTURN SPRIN RTURN LTRONI IL-S Size Valve Max PM OP M(X) M(X) 2*M(X)... 2*... 2*K VI lbs. 14 lbs VI / lbs. 14 lbs. 24 lbs VI lbs. 25 lbs VI lbs. 51 lbs VI / lbs. 53 lbs. 46 lbs VI / lbs. 65 lbs VI lbs. 72 lbs. Industrial ctuation (verage ssembly Weights) Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. 2-WY 3-WY TUTOR NON-SPRIN RTURN Size Valve Max PM OP SY1 SY2 SY3 SY4 SY5 SY6 SY VI lbs VI lbs VI / lbs. 44 lbs VI lbs VI lbs VI / lbs. 56 lbs VI lbs. 64 lbs VI lbs VI lbs VI lbs VI / lbs. 80 lbs VI lbs VI lbs VI lbs VI / lbs. 201 lbs VI lbs VI lbs. 456 lbs VI lbs. 645 lbs. Max PM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NM 4X rated and include 2 auxiliary switches and a heater US N LTIN MRI / RIN 5

6 utterfly Valve Selection Velocity hart and Installation VI Series Valves MSTR OMMON OMMON MSTR SLV MSTR 163 OMMON SLV SLV ONI O X10 ON/O OR MO@2V MSTR VLV IS OPN MSTR IL NON-IL ONI O X20 ON/O OR MO@2V MSTR VLV IS OPN MSTR IL NON-IL ONI O X30 ON/O OR MO@2V MSTR VLV IS OPN MSTR IL NON-IL X11 OPN OPN X21 OPN OPN X31 OPN OPN X12 OPN LOS X22 OPN LOS X32 OPN LOS X13 LOS NON-IL X23 LOS NON-IL X33 LOS NON-IL X14 LOS OPN X24 LOS OPN X34 LOS OPN X15 LOS LOS X25 LOS LOS X LOS LOS X Specifies i-irectional low apability Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W 6. ll 3-way assemblies are designed for 90 degree actuator rotation. VI low in Schedule 40 Pipe (luid Velocity in PM). Use with rooved Series utterfl y Valves. SIZ 1 PS 3 PS 5 PS 8 PS 10 PS 12 PS 15 PS 16 PS 20 PS ½ Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

eatures / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our H(U), rooved and SHP series butterfly valves and other quarter turn valve

rawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range.

easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label.

7 eatures / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our H(U), rooved and SHP series butterfly valves and other quarter turn valve applications. The patented gear drive mechanism provides for efficient, smooth operation while allowing easy manual override at any time. rawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range. ll units have NM 4X ratings, easily visible position indicators, international standard ISO5211 mounting systems, internal thermal motor overload protection, heater, dual auxiliary orm switches, and easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label. The units are easily visible in mechanical rooms with their characteristic elimo Orange color. Torque ranges are available from 310 to 31,150 in lbs. omed Position Indicator ast luminum over Powder oated NM 4X Rated Housing our over Screws for asy ccess Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. asily ccessible ield Wiring Terminal Positive Locking Switch ams ISO 5211Mounting System Thermally Protected rive Motor Simple, Single Handed Override Wheel (SY2~12) earing Seals Hardened Steel ear Sets US N LTIN MRI / RIN 7

8 SY... Series Non-Spring Return ctuator imensions SY-2~6... SY-1... SY-9~12... MOL IM (MX) SY-7~8... dd to im for cover removal IM IM (MX) IM Inches [mm] Inches [mm] Inches [mm] Inches [mm] Inches [mm] SY [155] 3.94 [100] 4.25 [108] 8mm - SY2~ [255] 7.48 [190] 7.87 [200] [330] 7.87 [200] SY4~ [315] 8.86 [225] 9.21 [234] [380] [300] SY7~ [420] 8.86 [225] 9.21 [234] [450] [340] SY9~ [590] 8.86 [225] [260] [470] [0] Note: ~ indicates range of actuator i.e., SY2~3 = SY-2 and SY-3 Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

9 Wire Size vs. Length of Run for SY Series ctuators Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V The N mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. o NOT mix LSS 1 & LSS 2 circuits in the same conduit. enerally, 24 V actuators over 100 V should be changed to 120 V models US N LTIN MRI / RIN 9

10 SY... Series Non-Spring Return ctuator urrent raws 24V / Model Torque Speed (90 ) Motor Power Run Start Lock SY1 15s 10W SY s 70W SY s 70W SY s 180W SY s 180W V Model Torque Speed (90 ) Motor Power Run Start Lock SY1 15s 10W SY s 70W SY s 70W SY s 180W SY s 180W SY s 120W SY s 120W SY s 120W SY s 180W SY s 220W SY s 250W SY s 300W V Model Torque Speed (90 ) Motor Power Run Start Lock SY1 15s 10W SY s 70W SY s 70W SY s 180W SY s 180W SY s 120W SY s 120W SY s 120W SY s 180W SY s 220W SY s 250W SY s 300W RUN- normal operation STRT- initial current draw LOK- power to the actuator but the motor is not moving Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

Interface Wiring etail SYx-MT, 24V, 120/230V ctuators: SYx-MT INSTLLTION NOTS

n adaption must be performed if any limit switch is adjusted.

New SY actuators must have an adaption performed before operation.

Supply om - Power Supply Hot + daption Tech.oc - 03/16 - Subject to change.

11 Interface Wiring etail SYx-MT, 24V, 120/230V ctuators: SYx-MT INSTLLTION NOTS UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 3. New SY actuators must have an adaption performed before operation. P Tool Service Jack onnection ontrol Signal + ontrol Signal - K + K - Power Supply om - Power Supply Hot + daption Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal + ontrol Signal - K + K - irection of Rotation 24V N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption irection of Rotation 120/230V US N LTIN MRI / RIN 11

Interface Wiring etail SYx-P L Open L lose N Power Supply (4) + Power Supply (5) ontrol Signal (6) ontrol Signal (7) Sensitivity switch se tting is position #3 for factory default.

2. VR1 and VR2 are factory calibrated and should not be moved. 3. Motor MS have been factory calibrated and should not be moved.

12 Interface Wiring etail SYx-P L Open L lose N Power Supply (4) + Power Supply (5) ontrol Signal (6) ontrol Signal (7) Sensitivity switch se tting is position #3 for factory default. To widen deadband, select a higher number (up to 9). Sensitivity eedback (11) eedback (12) VR2 VR1 INSTLLTION NOTS UTION Notes: 1. o not change sensitivity or dip switch settings with power applied! 2. VR1 and VR2 are factory calibrated and should not be moved. 3. Motor MS have been factory calibrated and should not be moved. ip Switch Settings O ON INPUT = 2-10 V O ON RSPONS = IRT O INPUT = 4-20m O RSPONS = RVRS ON ON WRNIN Potentiometer (actory Pre-set) O ON O ON O ON INPUT = 1-5 V OUTPUT = 4-20m OUTPUT = 2-10 V or 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω O ON O ON O ON LOSS O SINL = LOS (irect cting) LOSS O SINL = OPN (Reverse cting) LOSS O SINL = OPN (irect cting) LOSS O SINL = LOS (Reverse cting) LOSS O SINL = STOP Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. *On modulating actuators O NOT master/ slave using optional potentiometer. or modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω US N LTIN MRI / RIN

13 SY... Series Non-Spring Return ctuator UTION lectrical Travel djustment (actory Pre-set) SY-1 actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication LS2 LS1 uxiliary Switch for Opened Indication actory pre-set and calibrated. o not adjust - warranty voided LS2 LOS lockwise ecrease losed ngle ounter-clockwise Increase losed ngle LS1 OPN lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle UTION lectrical Travel djustment SY-2-12 actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication uxiliary Switch for Opened Indication Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. WRNIN LS2 LS1 actory pre-set and calibrated. o not adjust - warranty voided LS2 LOS LS1 OPN lockwise ecrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle Switches at left are shown with actuator fully open INSTLLTION NOTS UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. or the SYx-MT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release US N LTIN MRI / RIN 13

14 W546_12 Wiring for ontrol Valves On/Off, 24V, 120/230V SY ctuator Wiring iagram, SY1 5-24V On/Off SY V or 230V On/Off Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. NOTS SY ach actuator should be powered by a single, isolated 33 control transformer. using a common control signal input. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS SY V or 230V aution: Power Supply Voltage using a common control signal input V / Transformer round 120V or 230V / round Line Volts Open lose 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY N L1 H L2 Open lose 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY V or 230V Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. - (Open Indication) ontact Rating: V Max V Max. - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) - (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements US N LTIN MRI / RIN

15 W547_11 Wiring for ontrol Valves Proportional, 24V, 120/230V SY ctuator Wiring iagram, SY1-24P and SY1-110P (220P) Hazard Identification this manual. Read these carefully. UTION may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1 24P ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. NOTS SY1 110P (220P) aution: " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately V / Transformer round 120 or 230 V round Line Voltage 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. ontrol signal eedback 34 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-24P ontrol signal eedback 34 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-110P (220P) US N LTIN MRI / RIN 15

16 W547_2_11 Wiring for ontrol Valves Proportional, 24V, 120/230V ctuator: SY2 5-24MT SY MT SY MT Hazard Identification this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY MT ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. NOTS SY MT (230MT) aution: P Tool Service Jack ontrol Signal eedback ontrol Signal (+) ontrol Signal (-) eedback Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V / eedback Signal (-) 2 1 daption 8 9 ontrol Signal eedback 34 P ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) P 2 Y 1 U P Tool Service Jack 10 Y2 Y1 SYx-24MT Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) N L daption ddress 8 Y1 9 Y2 SYx-120MT 10 SYx-230MT Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. SY MT SY MT (230MT) US N LTIN MRI / RIN

17 W549_11 Wiring for ontrol Valves On/Off, 24V, 110/120/230V SY ctuator Wiring iagram, SY Multiple Wiring SY (220) Multiple Wiring Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. Line Voltage 24V Transformer Open lose K1 K1- K1- * * round 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY round 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY ctuator ctuator INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. Should be PT. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 120 or 230 V N L1 H L2 - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-24 Open lose K1 SY1-110 (220) K1- K1- - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1 ontact rrangements round 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. round 1 ommon 3 Open 4 losed HTR SY (220) - (Open Indication) ctuator ctuator - (losed Indication) ontact Rating: V Max. SY (220) US N LTIN MRI / RIN 17

18 W550_11 Wiring for ontrol Valves Proportional, 24V SY ctuator Wiring iagram, SY1-24P Multiple Wiring Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction the drag from the other reduces the torque output and causes overheating. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS SY1-24P ach actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. o not change sensitivity or dip switch settings with power applied V / Transformer Line Voltage 24V / Transformer Line Voltage ontrol Signal eedback () eedback () round 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-24P round ctuator - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-24P US N LTIN MRI / RIN

19 W550_2_11 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MT Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. - (Open Indication) - (losed Indication) ontact Rating: V Max. SY2 5-24MT ontrol Signal eedback ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) ontrol Signal (+) ontrol Signal (-) P INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). 33 ctuator Y 1 U ctuator Y 1 NOTS SY MT ach actuator should be powered by a single, isolated control transformer. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. ddress daption Y1 Y2 P Tool Service Jack P Tool Service Jack SYx-24MT ~/ /- /- ~/+ Power Supply om Power Supply Hot Power Supply om Power Supply Hot 24V / 24V / 33 eedback eedback Signal (+) U5 ddress 33 eedback Signal (-) 2 1 daption Y1 Y2 SYx-24MT 10 P US N LTIN MRI / RIN 19

20 W552_1_11 Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P Hazard Identification 120 or 230 V round Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. 8 9 Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. eedback () ctuator eedback (-) 12 eedback (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110P (220P) PPLITION NOTS round ctuator Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1-110P (220P) aution: Power supply voltage. power applied. ontrol Signal eedback () 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110P (220P) Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

21 W552_2 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MT SY MT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. ontrol Signal (+) INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY MT (230MT) aution: Power supply voltage. Y P Tool Service Jack N L Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) 1 ontrol Signal (-) 1 2 Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc. - (Open Indication) - (losed Indication) ontact Rating: V Max. SY MT SY MT ontrol Signal eedback eedback eedback Signal (+) eedback Signal (-) P ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) U ctuator Y 1 U P Tool Service Jack daption SYx-120MT SYx-230MT daption N L 3 ddress 8 Y1 9 Y2 10 Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) ddress 8 P ctuator SYx-120MT SYx-230MT Y1 Y US N LTIN MRI / RIN 21

22 Installation Recommendations VI Series utterfly Valves Maintenance Instructions Safety Precautions efore removing the valve from the line or loosening any bolts, it is important to verify the following conditions: 1. e sure the line is depressurized and drained. 2. e sure of the pipeline media. Proper care should be taken for protection against toxic and/or flammable fluids. 3. Never remove the valve without an Operator (Manual or utomatic) already attached to the valve shaft. 4. Never remove the Operator from the valve while the valve is in the pipeline under pressure. 5. lways be sure that the disc is cracked approximately 5 off of the closed position before removing the valve. Installation onsult the Victaulic I-100 field instructional handbook for product installation of the VI series butterfly valves. eneral Maintenance The following periodic preventative maintenance practices are recommended for all utterfly Valves. 1. Operate the valve from full open to full closed to assure operability. 2. heck flange bolting, actuator mounts and hangers for evidence of loosening and correct as needed. 3. Inspect the valve and surrounding area for previous or existing leakage at flange faces or shaft connections. 4. heck piping and/or wiring to actuators and related equipment for looseness and correct as needed. 5. If not in use, exercise the butterfly valve (full open and close) at least once a month. Tech.oc - 03/16 - Subject to change. elimo ircontrols (US), Inc US N LTIN MRI / RIN

BUTTERFLY VALVES VIC SERIES. High Performance for a Wide Range of Applications. of applications. percent leakage capability at each valve s

BUTTERFLY VALVES VIC SERIES. High Performance for a Wide Range of Applications. of applications. percent leakage capability at each valve s UTTRLY VLVS VI SRIS High Performance for a ide Range of pplications rooved butterfl y valves meet a wide range of applications. dvanced seat and disc design provides zero percent leakage capability at