F6 VIC Butterfly Valves Way Ductile Iron Grooved End Body

Transcription

1 6 VI utterfly Valves Way uctile Iron rooved nd ody psi (2 to 12 ) bubble tight shut-off Long stem design allows for 2 insulation ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. N /11 - Subject to change. elimo ircontrols (US), Inc. Technical ata Service chilled, hot water, 60% glycol low characteristic modifi ed equal percentage ction 90 rotation Sizes 2 to 12 Type of end fi tting grooved NSI/WW (606) Materials* ody isc Seat Shaft ductile iron STM 5, grade electroless nickel coated ductile iron PM 416 stainless steel ody pressure rating 300 psi at -30 to 275 Media temperature range -30 to 250 [-34 to 120 ] Operation ambient temperature range -22 to 122 [-30 to 50 ] Maximum close-off pressure psi Maximum velocity 20 PS *VI 300 Masterseal as manufactured by Victaulic ompany Valve Size v VI VI 2-1/ VI VI VI VI VI VI VI v 90 v 60 IN 2-way Valve Nominal Size N [mm] Type VI ½ VI VI VI VI VI VI VI VI Spring Return Suitable ctuators Non-Spring Return 2-way VI VI VI VI Series M Series M Series SY Series 1

2 6.393 [162.38] 6 VI utterfly Valves Way uctile Iron rooved nd ody Maximum imensions (Inches) Valve Size v 90 (Max) (Max) (Max) (Max) ctuator lose-off (PSI) 650VI [81.5] 4.7 [120] 8.0 [204] 13.2 [334] M VI 2½ [95.8] 4.7 [120] 8.0 [204] 13.6 [345] VI 2½ [95.8] 7.0 [178] 8.0 [204] 14.0 [8] M VI [95.8] 7.0 [178] 8.0 [204] 14.3 [4] 6100VI [117.6] 8.6 [219] 8.0 [204] 19.6 [499] 2*M 650VI [81.5] 2.0 [51] 8.6 [219] 14.0 [7] 665VI 2½ [95.8] 2.0 [51] 8.6 [219] 14.5 [8] VI 2½ [95.8] 8.6 [219] 8.6 [219] 18.7 [476] 2* 680VI [95.8] 2.0 [51] 8.6 [219] 14.7 [374] VI [82] 3.2 [82] 2.4 [61] 15.7 [398] 665VI 2½ [96] 3.2 [82] 2.4 [61] 16.2 [409] SY VI [96] 3.2 [82] 2.4 [61] 16.4 [415] VI [96] 4.6 [117] 9.2 [234] 26 [660] SY VI [118] 4.6 [117] 9.2 [234] 26.7 [679] 6125VI [150] 4.6 [117] 9.2 [234] 27.7 [704] SY2 / SY3 50/ 6150VI [150] 4.6 [117] 9.2 [234] 28.2 [717] SY2 / SY3 50/ 6VI [1] 7.3 [184] 10.9 [275] 33.3 [846] SY4 6250VI [163] 7.3 [184] 10.9 [275] [890] SY4 / SY5 50/ 6300VI [165] 7.3 [184] 10.9 [275] [916] SY6 SY6 and larger available in 110/220 V versions only. SY... maximum actuator ambient temperature is 150. Non-Spring Return Spring Return Non-Spring Return pplication Notes 1. Valves are rated at psi differential pressure in the closed position 2. 2-way assemblies are furnished assembled and tested, ready for installation. 3. imension allows for actuator removal without the need to remove the valve from the pipe. 4. elimo SY Series actuators are NM 4X rated. 5. Provide support for the actuator if it is mounted at any angle other than 90 vertical. 6. Installer is to use rigid type couplings for connecting the valve to the piping. imensions [217.25] [97.99] [47.05] low Rate (PM) Pressure rop - psi /60.3 mm 3 /88.9 mm 2 1/2 /73.0 mm & 76.1 mm 5 /141.3 mm, mm & mm 4 /114.3 mm & mm 6 /168.3 mm &165.1 mm & mm 8 /219.1 mm 10 /273.0 mm 12 /323.9 mm [101.6] N /11 - Subject to change. elimo ircontrols (US), Inc. 2

3 7 VI utterfly Valves Way uctile Iron rooved nd ody psi (2 to 12 ) bubble tight shut-off Long stem design allows for 2 insulation ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. N /11 - Subject to change. elimo ircontrols (US), Inc. Technical ata Service chilled, hot water, 60% glycol low characteristic modifi ed linear ction 90 rotation Sizes 2 to 12 Type of end fi tting grooved NSI/WW (606) Valve Materials* ody isc Seat Shaft ductile iron STM 5, grade electroless nickel coated ductile iron PM 416 stainless steel ody pressure rating 300 psi at -30 to 275 Media temperature range -30 to 250 [-34 to 120 ] Operation ambient temperature range -22 to 122 [-30 to 50 ] Maximum close-off pressure psi Maximum velocity 20 PS *VI 300 Masterseal as manufactured by Victaulic ompany Valve Size v VI VI 2-1/ VI VI VI VI VI VI VI v 90 v 60 IN 3-way Valve Nominal Size N [mm] Type VI ½ VI VI VI VI VI VI VI VI Spring Return Suitable ctuators Non-Spring Return 2-way VI VI VI VI Series M M Series SY Series 1

4 7 VI utterfly Valves Way uctile Iron rooved nd ody Maximum imensions (Inches) Valve Size v 90 (Max) (Max) (Max) (Max) ctuator lose-off (PSI) 750VI [82] 6.5 [165] 13.1 [334] 13.2 [334] M VI [82] 6.5 [165] 13.6 [347] 13.6 [345] M VI 2½ [96] 7.5 [191] 14.1 [6] 14.0 [8] VI 2½ [96] 7.5 [191] 14.1 [6] 14.3 [4] 2*M 780VI [96] 8.0 [204] 14.3 [4] 19.6 [499] VI [81.5] 2.0 [51] 8.6 [219] 14.0 [7] 665VI 2½ [95.8] 2.0 [51] 8.6 [219] 14.5 [8] 50 2* 665VI 2½ [95.8] 8.6 [219] 8.6 [219] 18.7 [476] 750VI [82] 6.5 [165] 15.7 [398] 15.7 [398] SY VI 2½ [96] 7.5 [191] 16.2 [409] 16.2 [409] VI 2½ [96] 7.5 [191] 25.7 [654] 16.4 [415] 780VI [96] 8.0 [204] 26.0 [660] 26 [660] SY VI [118] 9.6 [245] 26.7 [679] 26.7 [679] 7125VI [150] 11.4 [290] 27.7 [704] 27.7 [704] SY VI [150] 12.4 [315] 28.3 [717] 28.2 [717] VI [150] 12.4 [315] 32.1 [814] 33.3 [846] SY4... 7VI [1] 13.1 [333] 33.3 [846] [890] 7250VI [163] 15.4 [392].1 [890].1 [890] SY VI [163] 15.4 [392] 38.7 [981] 38.7 [981] SY VI [165] 16.5 [419] 39.7 [1007] 39.7 [1007] SY6 and larger available in 110/220 V versions only. SY... maximum actuator ambient temperature is 150. imensions pplication Notes 1. Valves are rated at psi differential pressure in the closed position 2. 2-way assemblies are furnished assembled and tested, ready for installation. 3. imension allows for actuator removal without the need to remove the valve from the pipe. 4. elimo SY Series actuators are NM 4X rated. 5. Provide support for the actuator if it is mounted at any angle other than 90 vertical. 6. Installer is to use rigid type couplings for connecting the valve to the piping [192] [115.6] [92.12] Non-Spring Return Spring Return Non-Spring Return low Rate (PM) Pressure rop - psi /60.3 mm 3 /88.9 mm 2 1/2 /73.0 mm & 76.1 mm 5 /141.3 mm, mm & mm 4 /114.3 mm & mm 6 /168.3 mm &165.1 mm & mm 8 /219.1 mm 10 /273.0 mm 12 /323.9 mm [213.51] N /11 - Subject to change. elimo ircontrols (US), Inc [97.99] [92.12] 2

5 eatures / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our H(U) and SHP series butterfly valves and other quarter turn valve applications. The patented gear drive mechanism provides for efficient, smooth operation while allowing easy manual override at any time. rawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range. ll units have NM 4X ratings, easily visible position indicators, international standard ISO5211 mounting systems, internal thermal motor overload protection, heater, dual auxiliary orm switches, and easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label. The units are easily visible in mechanical rooms with their characteristic elimo Orange color. Torque ranges are available from 310 to 31,150 in lbs. omed Position o Indicator ast luminum over Powder oated NM 4X Rated Housing our over Screws for asy ccess N /11 - Subject to change. elimo ircontrols (US), Inc. asily ccessible ield Wiring Terminal Positive Locking Switch ams ISO 5211Mounting System Thermally Protected rive Motor Simple, Single Handed Override Wheel (SY2~12) earing Seals Hardened Steel ear Sets

6 SY 24 Series Non-Spring Return ctuator Technical ata - 24 V pplication: The SY actuators are NM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata lectrical connection Motor protection ear train Operating range ½ conduit connector, screw terminals H lass insulation (SY-1), lass (SY-2 5) high alloy steel gear sets, self locking (SY -24) on/off, floating point (SY...24MT) 2-10 V, 4-20m, 0-10 V Sensitivity (SY 24MT) 0.4m/mV Reversal hysteresis (SY 24MT)1.0m/500mV (SY 24MT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 to +150 [-30 to +65 ] Humidity range up to 95% Housing type IP67, NM 4X Housing material die cast aluminum alloy gency listings ISO,, csus Power Supply 24 V/V 50/60Hz, single phase Power uty ycle Model Torque Speed onsumption On/Off MT Override Weight SY1-24(P) Nm/310 in-lbs 15s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-24(MT) 90Nm/801 in-lbs 15s % 75% Hand Wheel 11kg/24.5 lb. SY3-24(MT) 150Nm/13 in-lbs 22s % 75% Hand Wheel 11kg/24.5 lb. SY4-24(MT) 400Nm/60 in-lbs 16s % 75% Hand Wheel 22kg/48.5 lb. SY5-24(MT) 500Nm/4450 in-lbs 22s % 75% Hand Wheel 22kg/48.5 lb. N /11 - Subject to change. elimo ircontrols (US), Inc.

7 SY 120 Series Non-Spring Return ctuator Technical ata V pplication: The SY actuators are NM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata N /11 - Subject to change. elimo ircontrols (US), Inc. lectrical connection Motor protection ear train Operating range Sensitivity Reversal hysteresis ½ conduit connector, screw terminals H lass insulation (SY-1), lass (SY-2 12) high alloy steel gear sets, self locking (SY -110) on/off, floating point (SY...120MT) 2-10 V, 4-20m, 0-10 V (SY 120MT) 0.4m/mV (SY 120MT) 1.0m/500mV (SY 120MT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 to +150 [-30 to +65 ] Humidity range up to 95% Housing type IP67, NM 4X Housing material die cast aluminum alloy gency listings ISO,, csus Note: Leakage current is possible (<3.5 m). onnect ground before applying voltage. Power Supply 120 V 50/60Hz, single phase Speed Speed Power uty ycle Model Torque 60Hz 50Hz onsumption On/Off Proportional Override Weight SY1-110(P) Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-120(MT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-120(MT) 150Nm/13 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-120(MT) 400Nm/60 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-120(MT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-120(MT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-120(MT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel kg/79.5 lb. SY8-120(MT) 1500Nm/130 in-lbs 46s 55s % 75% Hand Wheel kg/79.5 lb. SY9-120(MT) 0Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-120(MT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-120(MT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-120(MT) 00Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. 37

8 SY 230 Series Non-Spring Return ctuator Technical ata V pplication: The SY actuators are NM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata lectrical connection Overload protection Motor protection ear train Operating range Power Supply Model ½ conduit connector, screw terminals thermally protected 1 cut-out H lass insulation (SY-1), lass (SY-2 12) high alloy steel gear sets, self locking (SY -220) on/off, floating point (SY...230MT) 2-10 V, 4-20m, 0-10 V Sensitivity (SY 230MT) 0.4m/mV Reversal hysteresis (SY 230MT) 1.0m/500mV (SY 230MT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 to +150 [-30 to +65 ] Humidity range up to 95% Housing type IP67, NM 4X Housing material die cast aluminum a lloy gency listings ISO,, csus Torque Speed 60Hz 230 V 50/60Hz, single phase Speed 50Hz Power onsumption uty ycle On/Off MT Override SY1-220(P) Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-230(MT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-230(MT) 150Nm/13 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-230(MT) 400Nm/60 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-230(MT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-230(MT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-230(MT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel kg/79.5 lb. SY8-230(MT) 1500Nm/130 in-lbs 46s 55s % 75% Hand Wheel kg/79.5 lb. SY9-230(MT) 0Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-230(MT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-230(MT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-230(MT) 00Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. Weight N /11 - Subject to change. elimo ircontrols (US), Inc. 38

9 SY Series Non-Spring ctuator imensions SY-2~6... SY-1... SY-9~12... SY-7~8... N /11 - Subject to change. elimo ircontrols (US), Inc. MOL IM (MX) dd to im for cover removal IM IM (MX) IM Inches [mm] Inches [mm] Inches [mm] Inches [mm] Inches [mm] SY [155] 3.94 [100] 4.25 [108] 8mm - SY2~ [255] 7.48 [190] 7.87 [] [330] 7.87 [] SY4~ [315] 8.86 [225] 9.21 [234] [380] [300] SY7~ [420] 8.86 [225] 9.21 [234] [450] [340] SY9~ [590] 8.86 [225] [260] [470] [0] Note: ~ indicates range of actuator i.e., SY2~3 = SY-2 and SY-3 39

10 Wire Size vs. Length of Run for SY Series ctuators SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V The N mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. o NOT mix LSS 1 & LSS 2 circuits in the same conduit. enerally, 24 V actuators over 100 V should be changed to 120 V models. N /11 - Subject to change. elimo ircontrols (US), Inc. 40

11 Interface Wiring etail SYx-MT, 24V, 120/230V ctuators: SYx-MT INSTLLTION NOTS UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. P Tool Service Jack onnection ontrol Signal + ontrol Signal - K + K - Power Supply om - Power Supply Hot + daption N /11 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal + ontrol Signal - K + K - irection of Rotation 24V N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption irection of Rotation 120/230V 41

12 SYx-P Interface Wiring etail Open L losed L Sensitivity VR2 VR1 ip Switch N Supply H - SI + IN - + OUT Sensitivity switchsetting is position #3 for factory default. To widen deadband, select a higher number (up to 9). INSTLLTION NOTS UTION Notes: 1. pplicable to the SY1 and legacy SY2-12 actuators. 2. o not change sensitivity or dip switch settings with power applied! 3. VR1 and VR2 are factory calibrated and should not be moved. 4. Motor MS have been factory calibrated and should not be moved. ip Switch Settings O ON INPUT = 2-10 V O ON RSPONS = IRT O INPUT = 4-20m O RSPONS = RVRS ON ON WRNIN Potentiometer (actory Pre-set) O ON O ON O ON INPUT = 1-5 V OUTPUT = 4-20m OUTPUT = 2-10 V or 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k 9, 10 0k When a valve is opened: 8, 9 0k 9, 10 1k O ON O ON O ON LOSS O SINL = LOS (irect cting) LOSS O SINL = OPN (Reverse cting) LOSS O SINL = OPN (irect cting) LOSS O SINL = LOS (Reverse cting) LOSS O SINL = STOP N /11 - Subject to change. elimo ircontrols (US), Inc. *On modulating actuators O NOT master/ slave using optional potentiometer. or modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k 9, 10 0k When a valve is opened: 8, 9 0k 9, 10 1k 42

13 SY Series Non-Spring ctuators UTION lectrical Travel djustment (actory Pre-set) SY-1 actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication LS2 LS1 uxiliary Switch for Opened Indication actory pre-set and calibrated. o not adjust - warranty voided LS2 LOS lockwise ecrease losed ngle ounter-clockwise Increase losed ngle LS1 OPN lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle SY-2-12 UTION lectrical Travel djustment actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication uxiliary Switch for Opened Indication N /11 - Subject to change. elimo ircontrols (US), Inc. WRNIN LS2 LS1 actory pre-set and calibrated. o not adjust - warranty voided LS2 LOS LS1 OPN Switches at left are shown with actuator fully open lockwise ecrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle INSTLLTION NOTS UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. or the SYx-MT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 43

14 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 120/230V ctuators: SY1-24 SY1-110 SY SY W546 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. NOTS SY ach actuator should be powered by a single, isolated 33 control transformer. using a common control signal input. Required: INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS SY (220) aution: Power Supply Voltage using a common control signal input. Required: V Transformer round 120 and 230 V round Line Volts Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY N L1 H L2 Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY (220) N /11 - Subject to change. elimo ircontrols (US), Inc. - (Open Indication) ontact Rating: V Max V Max. - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) - (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 44

15 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY1-24P SY1-110P SY1-220P W547 Hazard Identification this manual. Read these carefully. UTION may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1 24P ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. NOTS SY1 110P (220P) aution: " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately V Transformer round 120 and 230 V round Line Volts 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot N /11 - Subject to change. elimo ircontrols (US), Inc. ontrol signal 34 6 ontrol Signal (-) 7 ontrol Signal (+) (-) 12 (+) SY1-24P ontrol signal 34 6 ontrol Signal (-) 7 ontrol Signal (+) (-) 12 (+) SY1-110P (220P) 45

16 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY MT SY MT SY MT Hazard Identification this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. W547-2 W549 NOTS SY MT ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. NOTS SY MT (230MT) aution: P Tool Service Jack ontrol Signal ontrol Signal (+) ontrol Signal (-) Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V Signal (-) 2 1 daption Y2 Y1 SYx-24MT 10 P Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) ontrol Signal ontrol Signal (+) ontrol Signal (-) Y 1 P Tool Service Jack N L Signal (+) Signal (-) U daption ddress 3 P SYx-120MT SYx-230MT Y1 Y SY MT SY MT (230MT) 46

17 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 110/120/230V ctuators: SY SY SY Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 24 V Transformer round ctuator 120 and 230 V round ctuator Line Volts Open lose K1 K1-1 ommon 3 Open 4 losed HTR N L1 H L2 Open lose K1 K1-1 ommon 3 Open 4 losed HTR N /11 - Subject to change. elimo ircontrols (US), Inc. K1- - (Open Indication) - (losed Indication) ontact Rating: V Max. SY ctuator round 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY K1- - (Open Indication) - (losed Indication) ontact Rating: V Max. SY (220) round ctuator 1 ommon 3 Open 4 losed HTR - (Open Indication) - (losed Indication) ontact Rating: V Max. SY (220) - (Open Indication) ontact Rating: V Max V Max. - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) - (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 47

18 Wiring for ontrol Valves Proportional, 24V ctuators: SY1-24P W550 Hazard Identification 33 Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. 24 V Transformer Line Volts () round ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) (-) 12 (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-24P Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) V Transformer round ctuator NOTS SY1-24P ach actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. power applied. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Line Volts ontrol Signal () 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) (-) 12 (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) N /11 - Subject to change. elimo ircontrols (US), Inc. SY1-24P 48

19 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MT W550-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. 33 NOTS SY MT ach actuator should be powered by a single, isolated control transformer. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. ctuator P Tool Service Jack ontrol Signal (+) ontrol Signal (-) Y 1 /- ~/+ Power Supply om Power Supply Hot 24V N /11 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal - (Open Indication) Signal (+) Signal (-) P ontrol Signal (+) ontrol Signal (-) Signal (+) Signal (-) U ctuator Y 1 U ddress daption Y1 Y2 P Tool Service Jack ddress daption Y1 Y2 SYx-24MT SYx-24MT /- ~/ Power Supply om Power Supply Hot 33 24V 33 - (losed Indication) ontact Rating: V Max. P SY2 5-24MT 49

20 Wiring for ontrol Valves Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P W552-1 Hazard Identification 120 and 230 V round Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. 8 9 Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. () (-) 12 (+) ctuator - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110P (220P) PPLITION NOTS round ctuator Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1-110P (220P) aution: Power supply voltage. power applied. ontrol Signal () 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) (-) 12 (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) N /11 - Subject to change. elimo ircontrols (US), Inc. SY1-110P (220P) 50

21 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MT SY MT W552-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY MT (230MT) aution: Power supply voltage. Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) N L ontrol Signal (+) Y P Tool Service Jack 1 ontrol Signal (-) 1 2 Signal (+) Signal (-) U N /11 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal - (Open Indication) - (losed Indication) ontact Rating: V Max. P ontrol Signal (+) ontrol Signal (-) Signal (+) Signal (-) P 2 ctuator Y 1 U ctuator P Tool Service Jack daption SYx-120MT SYx-230MT daption SYx-120MT SYx-230MT N L ddress 8 Y1 9 Y2 10 Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) ddress 8 Y1 9 Y2 10 SY MT SY MT 51