Ball Valve Features and Benefi ts B2...VS / VSS and B3...L

Transcription

1 all Valve Features and enefi ts 2...VS / VSS and 3...L Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. 2-way and 3-way confi guration ronze with stainless steel trim (2-way) Nickel plated brass body (3-way) educed and full port capacities Two piece construction Electronic actuation NPT and fl anged connections ide C v range ir gap for use with hot water and steam systems Live load low maintenance stem packing 2 year warranty US CND LTIN MEIC / CIEN 1

2 Flow Pattern, Operation and Installation all Valves FLO PTTEN 2...VS/VSS 3...L Open CC Flow Direction Closed C to Open C to Open CC NOTE: 3 L are piped differently than 3 CCV Valves. PIPING DIGMS 2-way Valve Piping Diagram ater 3...L Diverting & Changeover (Switching) Valve Piping Diagram 2-way Valve Piping Diagram Steam NOTE: To avoid torque increase during off season shut down or other periods of inactivity longer than 1 month, the valve should be exercised (actuator or manually driven full open-closed cycle) at least once per month. This is necessary to avoid any application problems after an off season shut down. This is not required for 3...L valves. PIPING/MOUNTING OIENTTION ssembly can be mounted horizontally or vertically for water applications. For steam applications the valve can be mounted vertically but if mounted horizontally the valve must be 90 off center of the pipe. Do not install with actuator below pipe. Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. (ater application only) (Steam or water application) US CND LTIN MEIC / CIEN

3 Piping Sizing Geometry all Valves VLVE SIZE C v TYPE MODEL # ¾ Fp Cv 1 Fp Cv LINE SIZE ½ 1 2 NPT 2050VS ½ 2 2 NPT 2050VS ½ 4 2 NPT 2050VS ½ 15 2 NPT 2050VS ¾ 30 2 NPT 9VS/VSS ¾ 51 2 NPT 0VS NPT 4VS/VSS NPT 5VS ½ NPT 240VS NPT 249VS/VSS ½ NPT 315L ¾ NPT 320L NPT 325L ¼ 34 3 NPT 332L ½ 57 3 NPT 340L NPT 350L ¼ Fp Cv 1½ Fp Cv 2 Fp Cv 2½ Fp Cv 3 Fp Cv 4 Fp Cv Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 3

4 iring Instructions all Valves GENEL IING INSTUCTIONS NING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with fl exible conduit. lways read the controller manufacturer s installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) Typically actuators require a 24 VC class 2 transformer and draw a maximum of 10 V per actuator. The actuator enclosure cannot be opened in the fi eld, there are no parts or components to be replaced or repaired. EMC directive: 89/336/EEC Software class : Mode of operation type 1 Low voltage directive: 73//EEC Typical transformer sizing ctuator Series Voltage Max. V Per ctuator F LF N 24 4 L 24 3 CUTION It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectifi cation. Some controllers use full wave rectifi cation. hen these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed: 1. The TOTL current draw of the actuators (V rating) is less than or equal to the rating of the transformer. 2. Polarity on the secondary of the transformer is strictly followed. This means that all No. 1 wires from all actuators are connected to the common leg on the transformer and all No. 2 wires from all actuators are connected to the hotleg. Mixing wire No. 1 & 2 on one leg of the transformer will result in erratic operation or failure of the actuator and/or controls. Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed: 1. The transformers are properly sized. 2. ll No. 1 wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. ire type and wire installation tips For most installations, 18 or 16 Ga. cable works well with elimo actuators. Use code-approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire-tie the splice to reduce the possibility of the splice being inadvertently pulled apart. ire length for actuator installation Keep power wire runs below the lengths listed in the following tables. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. See section 1 for specifi c transformer sizing information for the actuator selected. Example: 3 actuators, 16 Ga wire 350 Ft 3 ctuators = 117 Ft. Maximum wire run Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

5 Nomenclature all Valves 2 19 VS +NMX 24 -MFT-X1 Valve 2 = 2-way 3 = 3-way Valve Size = ½ to 2 Industrial Construction/ Material VS = ronze ody, Stainless Steel all and Stem VSS = Stainless Steel ody, all and Stem L = Nickel Plated rass ody, Chrome Plated rass all and Stem ctuator Type Non-Spring eturn LM, LMX NM, NMX M, MX GM, GMX N, NX, X L, LX SY Spring eturn LF NF, NFX F, FX Electronic Fail-Safe GK, GKX Power Supply 24 = 24 VC/DC 120 = 120 VC 0 = 0 VC UP = VC or VDC Control -3-X1 = On/Off, Floating Point -MFT-X1 =Multi-Function Technology = Ω -S = uilt-in uxiliary Switch X models are customizable. Ordering Example Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. 1 Choose the valve actuator combination. 9VS+NMX24-MFT-X1 2 Specify preference or confi guration. Non-Spring Models NO = Normally Open NC = Normally Closed Spring eturn Models NO/FO = Normally Open/Fail Open NO/FC = Normally Open/Fail Closed NC/FO = Normally Closed/Fail Open NC/FC = Normally Closed/Fail Closed efers to valve ports to. 3 Set-Up NO For MFT orders only - select programming code Tagging (if needed) P (01) P-100xx (xx) P-200xx (xx) P-300xx (Fxx) P-400xx (Jxx) X-XXXXX X-XXXXX Control voltage applications Pulse width modulation applications Floating point applications On/off applications Create custom MFT confi guration code Create custom MFT confi guration in the fi eld with MFT actuator PC-Tool software 4 Does order require tagging? Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) Example: HU-1 FCU-2 Part number for tagging: Complete Ordering Example: 9VS+NMX24-MFT-X1 Confi guration: +NO Programming: US CND LTIN MEIC / CIEN 5

6 2...VS Series, 2-way, all Valve ronze ody, Stainless Steel all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design Technical Data Media chilled or hot water, glycol, 35# steam Flow characteristic modifi ed equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2 Type of end fi tting SE NPT (female connections) Materials: 1 Stem packing reinforced PTFE 2 Stem bearing reinforced PTFE 3 all 316 stainless steel 4 Seat (x2) reinforced PTFE w/ Durafi ll 5 etainer 16 (¾ - 1 ) stainless steel 584 (1¼ - 2 ) stainless steel 6 Gland 16 brass 7 Stem 316 stainless steel 8 Jam nut stainless steel 9 ody seal PTFE (1-1/4 to 2 ) 10 ody 584-C84400 bronze pplication This valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VV ox re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Up to 35 psi steam ½ PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II Composition: Z Style: 3 Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT Spring Non-Spring eturn eturn 1 ½ VS-01 2 ½ VS-02 4 ½ VS ½ VS ¾ 20 9VS 51 ¾ 20 0VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS LF Series NF F Series LM Series NM M Series GM Series SY Series Pressure rating 600 psig OG Media temp. range - F to +280 F (-30 C to +138 C) Close-off pressure F Maximum differential <600 psig pressure (ΔP) Flow Patterns 10 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

7 2...VSS Series, 2-way, all Valve Stainless Steel ody, all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design pplication These threaded valves are designed to provide modulating or two position control of hot or chilled water and saturated steam systems under 50 psi. Typical applications include reheat coils, VV terminal control, unit ventilators, and air handlers, especially in areas which have minimum profile requirements. Up to 50 psi steam ½ PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II, Composition: SS Style: 3 Technical Data Media chilled or hot water, glycol, 50# steam Flow characteristic modifi ed equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2 Type of end fi tting SE NPT (female connections) Materials: 1 Stem packing reinforced PTFE 2 Stem bearing reinforced PTFE 3 all 316 stainless steel 4 Seat (x2) reinforced PTFE w/ Durafi ll 5 etainer 16 (¾ - 1 ) stainless steel 584 (1¼ - 2 ) stainless steel 6 Gland Stem 316 stainless steel 8 Jam nut stainless steel 9 ody seal PTFE (1¼ to 2 ) 10 ody 351-CF8M 316 stainless steel Valve Nominal Size Type Suitable ctuators C v Inches DN Spring Non- Spring 2-way NPT [mm] eturn eturn 15 ½ VSS ¾ 20 9VSS VSS VSS LF Series F Series NM Series M GM SY Series Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Pressure rating 2000 psig OG (½ - 1 ) Media temp. range - F to +298 F (-30 C to +148 C) Close-off pressure F Maximum differential <600 psig pressure (ΔP) Flow Patterns US CND LTIN MEIC / CIEN 7

8 3...L Series, 3-way, all Valve Chrome Plated rass all and Nickel Plated Stem pplication This valve is typically used in air handling and fan coil units on heating or cooling coils, unit ventilators, VV box re-heat coils, and bypass loops. This valve is suitable for use as a diverting valve only. Technical Data Media Flow characteristic ction chilled or hot water, 60% glycol modifi ed linear 90 rotation to open C, to open CC Sizes ½, ¾, 1, 1¼, 1½, 2 Type of end fi tting NPT female ends Materials: ody nickel plated brass all chrome plated brass Stem nickel plated brass Stem seal o-ring EPDM Valve seat PTFE Leakage NSI VI Pressure rating 600 psig OG 600 psi DN (3...L) 400 psi DN (3...L) Media temp. range 0 F to 250 F [-18 C to +120 C] Close-off pressure 200 psi Maximum differential 50 psi pressure (ΔP) Valve Nominal Size Type Suitable ctuators 3-way Spring Non-Spring Electronic C v Inches DN [mm] NPT eturn eturn Fail-Safe 6.4 ½ L 12.8 ¾ L L 34 1¼ L 57 1½ L L LF Series F Series L Series N Series Flow Patterns to Open C to Open CC Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

9 all Valve Product ange Overview VS/VSS all Valve Product ange 2...VS/VSS, 3...L Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT 1 ½ VS-01* 2 ½ VS-02* 4 ½ VS-04* 15 ½ VS-15* 30 ¾ 20 9VS 51 ¾ 20 0VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS 15 ½ VSS-15* 30 ¾ 20 9VSS VSS VSS 3-way NPT 6.4 ½ L** 12.8 ¾ L** L** 34 1¼ L** 57 1½ L** L** Non-Spring eturn LM Series NM Series M Series GM Series NM Series M GM L Series N Series * For hot only or cold only applications. Not for temperature changeover applications. ** Not for steam applications SY Series Spring eturn LF Series NF Series NOTE: Industrial ball valves (2..VS, 2..VSS) have serviceable components. Proper maintenance of these parts will ensure a longer in-service life for the valves. The seats of these valves will require replacement at an interval consistent with number of full cycles the valve has be operated, or as field condition dictates. F Series LF NF F Series LF Series F Series Mode of Operation The control valve is operated by an electronic actuator that responds to a standard voltage for on/off control, by a modulating VDC/4 20 m, or 3-point control system. The actuator will then move the ball of the valve to the position dictated by the control signal thus changing the flow. Product Features Modified equal percentage of flow for 2. Modified linear flow for L valves are for diverting applications and are not rated for steam. ctuator Specifications Control type Manual override Electrical connection Valve Specifications Service on/off, fl oating point, modulating, 2-10 VDC multi-function technology (MFT) LM, NM, GM, M, SY, F, NF, GK 3 ft. [1 m] cable with ½ conduit fitting (excluding SY) chilled or hot water, (60% glycol), steam (2-way) Flow characteristic modified equal percentage (2), modifi ed linear (3...L) Sizes ½, ¾, 1, 1¼, 1½, 2 End fitting FNPT Materials ody all Stem Seats 2-way 3-way Stem packing 2-way NPT O-rings Media temp range 2..VS 2..VSS 3...L ody pressure rating 3-way Maximum inlet pressure Steam Leakage bronze (2..VS) stainless steel (2..VSS) nickel plated brass (3..L) stainless steel, bronze (2050VSS-15) chrome plated brass (3..L) stainless steel nickel plated brass (3..L) MPTFE, PTFE (2050) Tefl on PTFE MPTFE NPT EPDM (3..L) - F to +280 F [-30 C to +138 C] - F to +298 F [-30 C to +148 C] 0 F to 250 F [-18 C to +120 C] 600 psi DN (3..L ½ -1 ) 400 psi DN (3..L 1¼ - 2 ) 35 psi 2..VS 50 psi 2..VSS NSI Class IV (2..VS, VSS) 0% (3..L) US CND LTIN MEIC / CIEN 9

10 LF ctuators, On/Off Dimensions with 2-ay Valve Models LF24 US LF24-S US LF120 US LF120-S US w/built-in ux. Switch w/built-in ux. Switch Technical Data Control on/off, fl oating point Power supply LF24(-S) US 24 VC ± 20% 50/60 Hz 24 VDC ± 10% LF120(-S) US 120 VC ± 10% 50/60 Hz Power consumption LF24(-S) US running 5 holding 2.5 LF120(-S) US running 5.5 holding 3.5 Transformer sizing 7 V, class 2 power source Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Electrical protection 120V actuators double insulated Overload protection electronic throughout rotation ngle of rotation 95 Spring return direction reversible with C/CC mounting Position indication visual indicator 0 to 90 unning time <40 to 75 sec. (on/off) spring <25 -4 F to +1 F [-20 C to +50 C] <60 - F [-30 C] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Quality standard ISO 9001 Noise level max. 62 d() LF...-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) ated impulse voltage 800V (4kV for 120V model), Control pollution degree 3, Type of action 1. (1.. for -S models) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 50 ½ [67] 1.73 [44] 1.42 [36] 320L 50 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

11 LF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuator may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., LF24-S US and LF120-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 0 to Common 2 + Hot 3 LF24 US 2 On/Off wiring for 24 VC/DC LF-08 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off wiring for 120 VC 048-UX uxiliary Switch Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 11

12 LF24-MFT US ctuators, Multi-Function Technology Dimensions with 2-ay Valve Models LF24-MFT US LF24-MFT-S US w/built-in ux. Switch Technical Data Control MFT Control signal 2 to 10 VDC (4-20m with 500 Ω resistor) Power consumption running 2.5 holding 1 Transformer sizing 5 V (class 2 power source) Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20m 750 Ω for PM 500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator unning time <40 to 75 sec. (on/off) 150 sec. independent of load (proportional) spring <25 -4 F to +1 F [-20 C to +50 C] <60 F [-30 C] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 62 d() Quality standard ISO 9001 LF24-MFT-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 200 ½ [67] 1.73 [44] 1.42 [36] 320L 200 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

13 LF24-MFT US ctuators, Multi-Function Technology iring Diagrams 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) Y Input (5) U Output 3 ctuators may also be powered by 24 VDC. CC C MFT 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. Control signal may be pulsed from either the Hot (Source) or 6 Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. On/Off control (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) Y Input (5) U Output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. CC C MFT NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink MFT Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal US CND LTIN MEIC / CIEN 13

14 NF ctuators, On/Off Dimensions with 2-ay Valve C F D Models NF24-X1 NFUP-X1 NFUP-S-X1 Technical Data Control Power consumption NF24-X1 NFUP-X1 Transformer sizing w/built-in ux. Switch on/off running 6 holding 2.5 running 6 holding 2.5 NF24-X1 NFUP(-S)-X1 8.5 V (class 2 power source) 6 24 VC (class 2 powe source) VC VC Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cables Electrical protection 120V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator unning time control <75 seconds spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certified, CE Noise level max. 45 d() NFUP-S-X1 uxiliary switch 2 x SPDT, 3 ( V Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 400 ¾ VSS 1000 ¾ Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

15 NF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., NF24-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 5 to 85. Meets culus or UL and CS requirements without the need of an electrical ground connection. 1 1 Common 2 + Hot 3 On/Off wiring for NF24-X1 NF24-X _NF(X) 066_NF(X)UP NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. NFUP-X1 NFUP-S-X1 On/Off wiring for NFUP-X1, NFUP-S-X1 ht lk 067_NF(X)UP-S Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. uxiliary Switch NFUP-S-X US CND LTIN MEIC / CIEN 15

16 NF ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models NFX24-MFT-X1 NFX24-MFT-S-X1 Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 20% / -10% Power consumption running 6.5 holding 3 Transformer sizing 9 V, (class 2 power source) Electrical connection ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator, 0 to 95 unning time motor 150 seconds (default), variable (40 to 0 seconds) spring <20 -4 F to +1 F [-20 C to +50 C]; <60 - F [-30 F] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54, Enclosure Type 2 gency listings culus acc. to UL / -2-14, CN/ CS E :02, CE acc. to 2004/108/EC & 2006/95/EC Noise level <40 d() 150 seconds, run time dependent <62 d() spring return NFX24-MFT-S-X1 uxiliary switch 2 x SPDT, VC, UL pproved one set at +10, one adjustable 10 to 90 Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 400 ¾ VSS 1000 ¾ Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

17 NF ctuators, Multi-Function Technology iring Diagrams 2 CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. ( ) Control Signal (+) 4 to 20 m or 2 to 10 VDC Ω Ω 1/4 watt lk (1) Common ht (3) Y 1 Input, 2 to 10V Pnk (4) Y 2 Input Grn (5) U Output, 2 to 10V ctuators may also be powered by 24 VDC. CC C 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). VDC/4-20 m 5 Triac and can also be contact closures. Control signal may be pulsed from either the Hot (Source) or 6 Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. ( ) 2 to 10 VDC Feedback Signal (+) lk (1) Common ed (2) Hot + ht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point Direction of rotation switch CC CC C C 5 5 (C only) Position ( ) Feedback VDC (+) lk (1) Common ht (3) Y Input Pnk (4) Y 2 Input Org (5) U Output PM Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Two Position 24 VC/DC Transformer ( ) Position Feedback VDC (+) (C Only) ( ) Control Signal 2-10 VDC or 4 to 20 m (+) 7 Ω 500 Ω 1/4 watt Min* Mid* Max* Normal** C a Functions 0% 50% 100% Control mode acc. to Y lk (1) Common ed (2) Hot ht (3) Y Input Pnk (4) Y 2 Input Org (5) U Output 5 lk (1) Common ht (3) Y 1 Input, 2 to 10V Pnk (4) Y 2 Input Org (5) a b c * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override Control to Min, Mid, Max, Positions US CND LTIN MEIC / CIEN 17

18 NF ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models NFX24 Technical Data Control MFT Control signal Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 20% / -10% Power consumption running 6.5 holding 3 Transformer sizing 9 V (class 2 power source) Electrical connection ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 (adjustable with mechanical end stop, 35 to 95 ) Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator, 0 to 95 unning time control 150 seconds (default), variable (40 to 0 seconds) spring <20 -4 F to +1 F [-20 C to +50 C]; <60 - F [-30 F] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54, Enclosure Type 2 gency listings culus acc. to UL / -2-14, CN/ CS E :02, CE acc. to 2004/108/EC & 2006/95/EC Noise level <40 d() 150 seconds, run time dependent, <62 d() spring return Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 400 ¾ VSS 1000 ¾ Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

19 NF ctuators, Multi-Function Technology Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC High Limit Control Series 90 Series 90 high limit control Ω 24 lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 Shunting esistor Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor No. of actuators esistance Ω Ω Ω esistor Kit No. ZG , 7100 Shunting esistor 973, 7100 T775 Y Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common 020 ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC US CND LTIN MEIC / CIEN 19

20 F ctuators, On/Off Dimensions with 2-ay Valve C F D Models F24-X1 FUP-X1 FUP-S-X1 F24-3 FX24-3 Technical Data Control Power consumption FUP-X1 FUP-S-X1 Transformer sizing w/built-in ux. Switches on/off running 5 holding 2.5 running 7 holding 3.5 F24-X1 FUP(-S)-X1 7.5 V (class 2 power source) 7 24 VC (class 2 power source) VC VC Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cables Electrical protection 120V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 45 d() FUP-S-X1 uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 4VS VS VS 600 1¼ *9VS 600 1½ N/ *240VS 600 1½ N/ *249VS N/ VSS *249VSS N/ Dimensions with 3-ay Valve 4.04 [102.7] 3.93 [99.9] Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 200 1¼ [105] 2.00 [51] 2.19 [56] 340L 200 1½ [1] 2.44 [62] 2.61 [67] 350L [142] 2.67 [68] 3.11 [79] 9.77 [248.2] 2.50 [63.5] Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

21 F ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85. p j y 1 Common 2 + Hot 3 F24-X1 2 On/Off iring for F24-X1, F24-3, FX _F24-X1 003_F24-X1 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for FUP-X1, FUP-S-X1 FUP-X1 FUP-S-X1 195_FUP-S-X1 uxiliary Switches FUP-S-X1 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

22 F ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models FX24-MFT-X1 FX24-MFT-S-X1 FX24 FX24-MFT w/built-in ux. Switches Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Ω (MFT95) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 7.5 holding 3 Transformer sizing 10 V (class 2 power source) Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 45 d() FX24-MFT-S-X1 uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 4VS VS VS 600 1¼ *9VS 600 1½ N/ *240VS 600 1½ N/ *249VS N/ VSS VSS ¼ *249VSS N/ Dimensions with 3-ay Valve 4.04 [102.7] 3.93 [99.9] Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 200 1¼ [105] 2.00 [51] 2.19 [56] 340L 200 1½ [1] 2.44 [62] 2.61 [67] 350L [142] 2.67 [68] 3.11 [79] 9.77 [248.2] 2.50 [63.5] Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

23 F ctuators, Multi-Function Technology iring Diagrams 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) Y Input (5) U Output 3 ctuators may also be powered by 24 VDC. IN4004 or IN4007 diode (IN4007 supplied, elimo part number ). On/Off control CC C MFT 5 Triac and can also be contact closures. Control signal may be pulsed from either the Hot (Source) or 6 Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) Y Input (5) U Output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink CC C MFT 302_FX24-MFT...MFT Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal uxiliary Switches FX24-MFT-S-X US CND LTIN MEIC / CIEN

24 F ctuators, Multi-Function Technology Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC High Limit Control Series 90 Series 90 high limit control Ω 24 lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 Shunting esistor Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor No. of actuators esistance Ω Ω Ω esistor Kit No. ZG , 7100 Shunting esistor 973, 7100 T775 Y Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common 020 ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

25 LM()X24-3-X1, LX24-3 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models LM24-3-X1 LMX24-3-X1 LX24-3 Technical Data Control on/off, fl oating point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 1.5 holding 0.2 Transformer sizing 3 V (class 2 power source) Electrical connection LM24-3-X1 ½ conduit connector 3 ft., 18 G plenum rated cables Overload protection electronic throughout 0 to 95 rotation Input impedance 600 Ω ngle of rotation 95 Torque 45 in-lbs [5 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C.2 No. 24 certifi ed, CE acc. to 73//EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F H1 H2 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 200 ½ [67] 1.73 [44] 1.42 [36] 320L 200 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] US CND LTIN MEIC / CIEN 25

26 LM()X24-3-X1, LX24-3 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

27 LMX24-MFT-X1, LX24-MFT ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models LMX24-MFT-X1 LX24-MFT Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 2 Transformer sizing 3.5 V (class 2 power source) Electrical connection 3 ft. [1m], 10 ft. [3m], 16 ft. [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 100k Ω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation 95 Torque 45 in-lbs [5 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) variable (35 to 150 seconds) Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 200 ½ [67] 1.73 [44] 1.42 [36] 320L 200 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] US CND LTIN MEIC / CIEN 27

28 LMX24-MFT-X1, LX24-MFT ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line VC/DC Transformer Position ( ) Feedback VDC (+) a 2 lk (1) Common ed (2) Hot ht (3) Y Input Org (5) U Output ZG-01 may be used. Contact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. On/Off control 1 2 lk (1) Common ed (2) Hot to 10 VDC Feedback Signal 7 4 ht (3) Y 1 Input 8 Pnk (4) Y 2 Input Org (5) U Output 2 to 10V MFT Floating Point 1 3 Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) Ω 500Ω 1/4 watt 6 2 lk (1) Common ht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common ht (3) Y Input Org (5) U Output T 399 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

29 NM()X24-3-X1, N24-3 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models NM24-3-X1 NMX24-3-X1 N24-3 Technical Data Control on/off, fl oating point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 2.0 holding 0.2 Transformer sizing 4 V (class 2 power source) Electrical connection NM24-3-X1 3 ft., 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 600 Ω ngle of rotation max 95, adjustable with mechanical stop Torque 90 in-lbs [10 Nm] Direction of rotation reversible with =CC with decreasing control signal (10-2V) =C with decreasing control signal (10-2V) Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C.2 No. 24 certifi ed, CE acc. to 73//EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 ¾ VS 400 ¾ VSS ½ VSS 1000 ¾ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 200 1¼ [105] 2.00 [51] 2.19 [56] US CND LTIN MEIC / CIEN 29

30 NM()X24-3-X1, N24-3 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

31 NMX24-MFT-X1, NX24-MFT ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models NMX24-MFT-X1 NX24-MFT Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 3.5 (1.25 ) Transformer sizing 5.5 V (class 2 power source) Electrical connection 3 ft. [1m], 10 ft. [3m], 16 ft. [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation max 95, adjust. with mechanical stop electronically variable Torque 90 in-lbs [10 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) Variable (45 to 170 secondss) Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 ¾ VS 400 ¾ VSS ½ VSS 1000 ¾ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 200 1¼ [105] 2.00 [51] 2.19 [56] US CND LTIN MEIC / CIEN 31

32 NMX24-MFT-X1, NX24-MFT ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line VC/DC Transformer Position ( ) Feedback VDC (+) a 2 lk (1) Common ed (2) Hot ht (3) Y Input Org (5) U Output ZG-01 may be used. Contact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. On/Off control 1 2 lk (1) Common ed (2) Hot to 10 VDC Feedback Signal 7 4 ht (3) Y 1 Input 8 Pnk (4) Y 2 Input Org (5) U Output 2 to 10V MFT Floating Point 1 3 Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) Ω 500Ω 1/4 watt 6 2 lk (1) Common ht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common ht (3) Y Input Org (5) U Output T 399 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

33 M()X24-3-X1, ()X24-3 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models M24-3-X1 MX24-3-X1 X S Technical Data Control on/off, fl oating point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 2.5 holding 0.2 Transformer sizing 5.5 V (class 2 power source) Electrical connection M24-3-X1 ½ conduit connector 3 ft., 18 G plenum rated cable Overload protection electronic throughout 0 to 95 rotation Input impedance 600 Ω ngle of rotation max 95, adjustable with mechanical stop Torque 180 in-lbs [20 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C.2 No. 24 certifi ed, CE acc. to 73//EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 5VS VS 600 1¼ VSS Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 340L 200 1½ [1] 2.44 [62] 2.61 [65] 350L [142] 2.67 [68] 3.11 [79] US CND LTIN MEIC / CIEN 33

34 M()X24-3-X1, ()X24-3 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 VDC. 5 Only connect common to neg. ( ) leg of control circuits. On/Off control Meets culus or UL and CS requirements without the need of an electrical ground connection NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 34

35 MX24-MFT-X1, X24-MFT ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Models MX24-MFT-X1 MX24 X24-MFT Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 4 (1.25 ) Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft. [1m], 10 ft. [3m], 16 ft. [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation max 95, adjust. with mechanical stop electronically variable Torque 180 in-lbs [20 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) variable (90 to 350 seconds) Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 5VS VS 600 1¼ VSS Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 340L 200 1½ [1] 2.44 [62] 2.61 [65] 350L [142] 2.67 [68] 3.11 [79] US CND LTIN MEIC / CIEN 35

36 MX24-MFT-X1, X24-MFT ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line VC/DC Transformer Position ( ) Feedback VDC (+) a 2 lk (1) Common ed (2) Hot ht (3) Y Input Org (5) U Output ZG-01 may be used. Contact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. On/Off control 1 2 lk (1) Common ed (2) Hot to 10 VDC Feedback Signal 7 4 ht (3) Y 1 Input 8 Pnk (4) Y 2 Input Org (5) U Output 2 to 10V MFT Floating Point 1 3 Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) Ω 500Ω 1/4 watt 6 2 lk (1) Common ht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common ht (3) Y Input Org (5) U Output T 399 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

37 MX24-MFT-X1 ctuators, Multi-Function Technology Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC High Limit Control Series 90 Series 90 high limit control Ω 24 lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 Shunting esistor Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor No. of actuators esistance Ω Ω Ω esistor Kit No. ZG , 7100 Shunting esistor 973, 7100 T775 Y Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common 020 ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC US CND LTIN MEIC / CIEN 37

38 GM24-3-X1 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F Models GM24-3-X1 Technical Data Control on/off, fl oating point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 4 holding 2 Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft. [1m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout stroke ngle of rotation 95 Direction of rotation reversible with Position indication refl ective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2/IP54 with cable entry down Housing material UL94-5V (fl ammability rating) gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <45 d() Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 1½ VS 400 1½ VS VSS Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

39 GM24-3-X1 ctuators, On/Off, Floating Point iring Diagrams 1 Provide overload protection and disconnect as required. 2 ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 VDC. Position feedback cannot be used with Triac sink controller. 4 The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) 5 or the Common (sink) 24 VC line. Contact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller. GM24-3-X1 On/Off control Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Floating Point or On/Off control GM24-3-X1 Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction US CND LTIN MEIC / CIEN 39

40 GMX24-MFT-X1 ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Models GMX24-MFT-X1 GMX24 Technical Data Control on/off, fl oating point, 2 to 10 VDC Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 4.5 holding 3 Transformer sizing 7 V (class 2 power source) Electrical connection 3 ft. [1m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout stroke Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation 95 Direction of rotation reversible with Position indication refl ective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2/IP54 with cable entry down Housing material UL94-5V (fl ammability rating) gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <45 d() Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 1½ VS 400 1½ VS VSS Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

41 GMX24-MFT-X1 ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 2 ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 VDC. Position feedback cannot be used with Triac sink controller. 4 The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) 5 or the Common (sink) 24 VC line. 6 ZG-01 may be used. Contact closures & also can be triacs. 7 & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator 8 must be connected to the hot connection of the controller VC/DC Transformer Position ( ) a lk (1) Common ed (2) Hot ht (3) Y Input Feedback VDC (+) Org (5) U Output Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. On/Off control Floating Point VDC/4-20 m to 10 VDC Feedback Signal 1 Control Signal 4 to 20 m or 2 to 10 VDC 1 3 ( ) (+) Ω 500Ω 1/4 watt (C only) 2 Position Feedback VDC ( ) (+) lk (1) Common ed (2) Hot + ht (3) Y 1 Input Pnk (4) Y 2 Input Org (5) U Output 2 to 10V MFT lk (1) Common 8 ht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V MFT lk (1) Common ht (3) Y Input Org (5) U Output PM T US CND LTIN MEIC / CIEN 41

42 GMX24-MFT-X1 ctuators, Multi-Function Technology Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC High Limit Control Series 90 Series 90 high limit control Ω 24 lk (1) Common ht (3) 24 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 Shunting esistor Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor No. of actuators esistance Ω Ω Ω esistor Kit No. ZG , 7100 Shunting esistor 973, 7100 T775 Y Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC lk (1) Common 020 ht (3) 25 ht (4) ht (5) ht (6) U5 Output 2 to 10 VDC Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

43 SY...24 NEM 4X Industrial Style ctuators, 24VC ttention SY Series actuators are fractional horsepower devices, and utilize full-wave power supplies. Observe wire sizing and transformer sizing requirements. Proportional models CNNOT be connected to elimo direct coupled (F, M, GM etc) actuator power supplies or any type of half-wave device. You MUST use a separate, dedicated transformer or power supply to power the SY actuator. Please do not connect other automation equipment to the dedicated SY supply source. You MUST use four wires (plus a ground) to control a proportional control SY actuator (See SY iring Section). Models SY1-24(P) SY2-24MFT Technical Data - continued Power Consumption SY1-24(P) 1.8 SY2-24MFT 3.0 Torque SY1-24(P) 35 Nm / 310 in-lbs SY2-24MFT 90 Nm / 801 in-lbs Manual Override SY1-24(P) 8mm wrench SY2-24 hand wheel unning Time SY1-24(P) 15 seconds SY2-24MFT 15 seconds Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Technical Data Power supply 24 VC 50/60 Hz, single phase Electrical connection ½ conduit connector, screw terminals Overload protection thermally protected 135 C cut-out Motor protection SY1 H class insulation SY2... F class insulation Geartrain high alloy steel gear sets, self locking Operating range SY SY...-24MFT on/off 2-10 VDC, 4-20m, 1-5 VDC Sensitivity SY...-24MFT 0.2 m / 100mV Feedback SY...-24MFT 2-10 VDC, 4-20 m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPDT, VC factory set for 3 and 87 change of state mbient temperature - F to +150 F [-30 C to +65 C] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, CE, ccsus US CND LTIN MEIC / CIEN 43

44 SY...24 NEM 4X Industrial Style ctuators, 24VC iring Diagrams T 1 Transformer sizing = SY actuator draw X 1.25 (safety margin) EXMPLE: SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 VC = 90V Transformer. There can be no connection (internal to automation controller, external wiring, or otherwise) between actuator supply neutral & control signal reference. These actuators are full wave devices. ny connection to half wave equipment will result in equipment damage. 2 Do not change sensitivity or dip switch settings with power applied. 3 Terminals 6 & 11 can be common when control and feedback signals are both set for 2-10VDC operation. 4 Use of feedback is optional. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control for SY(2-5)-24 Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. 2 to 10 vdc or 4 to 20 m control signal for SY1-24P US CND LTIN MEIC / CIEN

45 SY NEM 4X Industrial Style ctuators, 120VC pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HVC and Commercial applications. Offered on the HDU and HD butterfly valve series, these actuators are available for on/off and modulating applications. Depending on the application, they are available in 24 VC, 120 VC and 0 VC. Models SY1-110(P) SY2-110 SY2-120MFT Technical Data - continued Power Consumption SY1-110(P) 0.5 SY2-120MFT 1.0 SY Torque SY1-110(P) 35 Nm / 310 in-lbs SY2-120MFT 90 Nm / 801 in-lbs SY Nm / 801 in-lbs Manual Override SY1-110(P) 8mm wrench SY2-120MFT hand wheel SY2-110 hand wheel unning Time 50 Hz 60 Hz SY1-110(P) 13 seconds 12 seconds SY2-120MFT 17 seconds 15 seconds SY seconds 16 seconds Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Technical Data Power supply 120 VC 50/60 Hz, single phase Electrical connection ½ conduit connector, screw terminals Overload protection thermally protected 135 C cut-out Motor protection SY1 H class insulation SY2... F class insulation Geartrain high alloy steel gear sets, self locking Operating range SY SY MFT on/off, fl oating point 2-10 VDC 4-20 m, 1-5 VDC Sensitivity SY MFT 0.2 m / 100mV Feedback SY...120MFT 2-10 VDC, 4-20 m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPDT, VC factory set for 5 and 85 change of state mbient temperature - F to +150 F [-30 C to +65 C] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, CE, ccsus US CND LTIN MEIC / CIEN 45

46 SY NEM 4X Industrial Style ctuators, 120VC iring Diagrams Hazard Identification arnings and Cautions appear at appropriate sections throughout this manual. ead these carefully. CUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. NOTES SY1-110P Caution: Power supply voltage. with power applied. NOTES SY2-120MFT Caution: Power supply voltage. 120 VC N L1 H L2 G 35 Feedback () 36 G Ground ctuator 4 Power Supply Com 5 Power Supply Hot 6 Control Signal (-) 7 Control Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) C E F LS3 - (Open Indication) Contact ating: VC Max VC Max. LS4 -E (Closed Indication) SY1-110P INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. G G Ground ctuator 4 Power Supply Com PPLICTION NOTES Control Signal 5 Power Supply Hot 6 Control Signal (-) 7 Control Signal (+) 35 ecommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator Internal Use Only 9 Internal Use Only 10 Internal Use Only 36 Use of feedback is optional. Power Supply Com 120v (N) Power Supply Hot 120v (H) Feedback () Feedback (-) 12 Feedback (+) LS3 Control Signal Feedback 36 Feedback 36 G G Control Signal (+) Control Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - Control Signal (+) Control Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE PE Y 1 U5 2 C1 C2 ctuator Y 1 U5 2 C1 C2 ctuator PC Tool Service Jack PC Tool Service Jack N daption SYx-120S/MFT N daption SYx-120MFT L L Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only Power Supply Com 120v (N) Power Supply Hot 120v (H) Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only LS3 -C (Open Indication) C D LS4 E D-F (Closed Indication) F Contact ating: VC Max. SY2-120MFT C E F - (Open Indication) Contact ating: VC Max VC Max. LS4 -E (Closed Indication) SY1-110P Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

47 SY...0 NEM 4X Industrial Style ctuators, 0VC ttention SY Series actuators are fractional horsepower devices, and utilize full-wave power supplies. Observe wire sizing and transformer sizing requirements. Proportional models CNNOT be connected to elimo direct coupled (F, M, GM etc) actuator power supplies or any type of half-wave device. You MUST use a separate, dedicated transformer or power supply to power the SY actuator. Please do not connect other automation equipment to the dedicated SY supply source. You MUST use four wires (plus a ground) to control a proportional control SY actuator (See SY iring Section). Models SY1-0(P) SY2-0MFT Technical Data - Continued Power consumption SY1-0(P) 0.3 SY2-0MFT 0.5 Torque SY1-0(P) 35 Nm / 310 in-lbs SY2-0MFT 90 Nm / 801 in-lbs Manual Override SY1-0(P) 8mm wrench SY2-0MFT hand wheel unning Time 50 Hz 60 Hz SY1-0(P) 13 seconds 12 seconds SY2-0MFT 17 seconds 15 seconds Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. Technical Data Power supply 0 VC 50/60 Hz, single phase Electrical connection ½ conduit connector, screw terminals Overload protection thermally protected 135 C cut-out Motor protection SY1 H class insulation SY2... F class insulation Geartrain high alloy steel gear sets, self locking Operating range SY...-0 SY...-0MFT on/off, fl oating point 2-10 VDC, 4-20 m, 1-5 VDC Sensitivity SY...-0MFT 0.2 m / 200mV Feedback SY...-0MFT 2-10 VDC, 4-20 m ngle of rotation mechanically limited to 95 Direction of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPDT, 5 250VC factory set for 5 and 85 change of state mbient temperature - F to +150 F [-30 C to +65 C] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, CE, ccsus US CND LTIN MEIC / CIEN 47

48 SY...0 NEM 4X Industrial Style ctuators, 0VC iring Diagrams Hazard Identification arnings and Cautions appear at appropriate sections throughout this manual. ead these carefully. CUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. NOTES SY1-0P Caution: Power supply voltage. with power applied. NOTES SY2-0MFT Caution: Power supply voltage. 0 VC N L1 H L2 G 35 Feedback () 36 G Ground 4 Power Supply Com 5 Power Supply Hot 6 Control Signal (-) 7 Control Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) C E F ctuator LS3 - (Open Indication) Contact ating: VC Max VC Max. LS4 -E (Closed Indication) SY1-0P INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. G G Ground ctuator 4 Power Supply Com PPLICTION NOTES Control Signal 5 Power Supply Hot 6 Control Signal (-) 7 Control Signal (+) ecommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Power Supply Com 0v (L1) Power Supply Hot 0v (L2) 35 Feedback () 36 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) LS3 Control Signal Feedback 36 Feedback 36 G G Control Signal (+) Control Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - Control Signal (+) Control Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE PE Y 1 U5 2 C1 C2 ctuator Y 1 U5 2 C1 C2 ctuator PC Tool Service Jack PC Tool Service Jack daption SYx-0MFT daption SYx-0MFT N N L L Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only Power Supply Com 0v (L1) Power Supply Hot 0v (L2) Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only LS3 -C (Open Indication) C D LS4 E D-F (Closed Indication) F Contact ating: VC Max. SY2-0MFT C E F - (Open Indication) Contact ating: VC Max VC Max. LS4 -E (Closed Indication) SY1-0P Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

49 all Valve Dimensions with SY... Series ctuators Dimensions with 2-ay Valves C 2VSS_SYDIMS D SY1 SY1 & SY2 SY2 Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D 2050VS ½ VS ½ VS ½ VS ½ VS 600 ¾ VS 600 ¾ VS VS VS 600 1¼ VS 600 1½ VS 600 1½ VS VS VS 600 2½ Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 49

50 Valve ccessories ETHE SHIELDS VLVES L N G K GK/ GK LF NF F/ F ZS-EPIV-EV-20-NF For valve sizes ½ [DN15] to ¾ [DN20] (cover only) Energy Valves epiv LM NM M GM ZS-EPIV-EV-50-SCNF For valve sizes 1 [DN25] to 2 [DN50] on nonfail-safe actuator series (cover only) For valve sizes ½ [DN15] to 2 [DN50] on electronic fail-safe actuator series (cover only) Energy Valves epiv ZS-EPIV-EV-80 For NSI 125, valve sizes 2½ [DN65] and 3 [DN80] (cover only) ZS-EPIV-EV-150 For NSI 125, valve sizes 4 [DN100], 5 [DN125], and 6 [DN150] (cover only) ZS-CCV-90* Kit for LF actuator series ZS-CCV-100* Kit for L/ actuator series ZS-CCV-110* Kit for F actuator series Energy Valves epiv Energy Valves epiv PICCV CCV PICCV CCV PICCV CCV ZS-SPV-10 For NM, M,GM, NF, F, and GK actuator series ZS-SPV-20 For dual mounted GM, F, and GK actuator series ZS-VVS-0002 For LM actuator series on VS/VSS models ZS-VVS-0003 For LF actuator series on VS/VSS models all Valves ZTH EPLCEMENT CLES VLVES M GM G D GK DK SY ZK1-GEN Cable for use with ZTH US to connect to new generation non-spring return actuator via diagnostic/ programming socket ZK2-GEN Cable for use with ZTH US to connect to new generation non-spring return actuator via diagnostic/ programming socket all Valves utterfl y Valves vailable for all MFT ctuators Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. ZK6-GEN Cable for use with ZTH US to connect to SY actuator via JII port all Valves utterfl y Valves US CND LTIN MEIC / CIEN

51 Valve ccessories TTEY CKUP VLVES LM/ L NM/ N M GM G/ D EV V P SY NSV24 US attery backup module all Valves Globe Valves utterfl y Valves NSV-T 12VDC 1.2 H battery (2 required) all Valves Globe Valves utterfl y Valves EXT-NSV * attery backup system for SY1 - SY3 120 VC, on/off actuators all Valves utterfl y Valves EXT-NSV * attery backup system for SY1 - SY3 120 VC, MFT actuators all Valves utterfl y Valves EXT-NSV-11-24* attery backup system for SY1 24 VC, on/off actuators all Valves utterfly Valves EXT-NSV-12-24* attery backup system for SY1 24 VC, MFT actuators all Valves utterfly Valves EXT-NSV--0* attery backup system for SY1 - SY3 0 VC, on/off actuators all Valves utterfl y Valves EXT-NSV--0* attery backup system for SY1 - SY3 0 VC, MFT actuators all Valves EXT-NSV * attery backup system for SY4 - SY6 120 VC, on/off actuators EXT-NSV * attery backup system for SY4 - SY6 120 VC, MFT actuators Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc. EXT-NSV * attery backup system for SY7 - SY VC, on/off actuators EXT-NSV * attery backup system for SY7 - SY VC, MFT actuators EXT-NSV-13-24* attery backup system for SY2 - SY5 24 VC, on/off actuators EXT-NSV-14-24* attery backup system for SY2 - SY5 24 VC, MFT actuators EXT-NSV--0* attery backup system for SY4 - SY6 0 VC, on/off actuators EXT-NSV-24-0* attery backup system for SY4 - SY6 0 VC, MFT actuators EXT-NSV-25-0* attery backup system for SY7 - SY12 0 VC, on/off actuators EXT-NSV-26-0* attery backup system for SY7 - SY12 0 VC, MFT actuators utterfly Valves US CND LTIN MEIC / CIEN 51

52 Valve ccessories UXILIY SITCHES & POTENTIOMETES VLVES L/LM N/NM /M G/GM K GK/GK S1 uxiliary switch 1x SPDT, 3 ( VC S2 uxiliary switch 2x SPDT, 3 ( VC P140 G Feedback potentiometer 140 P500 G Feedback potentiometer 500 P500 G Feedback potentiometer 500 P1000 G Feedback potentiometer 1000 P2800 G Feedback potentiometer 2800 P5000 G Feedback potentiometer 5000 P10000 G Feedback potentiometer vailable for ll Valves VLVES LV/SV EV V LVK/SVK VK SY S2-GV uxiliary switch 2x SPDT, 3 ( VC for LV, SV, EV, and VK series actuators. SY-1000-F01 Feedback potentiometer 1000, 2 position, factory installed option only SY-1000-F02 Feedback potentiometer 1000, modulating (models Syx -P, -S or MFT), factory installed option only Energy Valves epiv Globe Valves all Valves utterfly Valves all Valves utterfly Valves ELECTIC DISCONNECT VLVES SY HO-120V Local electric disconnect for SY2-SY12 110/0V - 2 position HO-120VMFT Local electric disconnect for SY2-SY12 110/0V - modulating HO-24V Local electric disconnect for SY2-SY12 24V - 2 position HO-24VMFT Local electric disconnect for SY2-SY12 24V - modulating all Valves utterfly Valves all Valves utterfl y Valves all Valves utterfl y Valves all Valves utterfl y Valves Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

53 Valve ccessories POGMMING TOOLS Near Field Communication (NFC) pp llows fast programming, commissioning, and troubleshooting even when the actuator is not powered. vailable through Google Play here vailable on NFC Labeled ctuators Only MFT-P elimo MFT confi guration software (V3.X), includes PC-Tool software (interface cables [ZTH US] not included). Physical copy of software. Free download also available at ZTH US Handheld interface module that allows fi eld programming. Includes ZK1-GEN, ZK2-GEN, and ZK6-GEN cables vailable for all MFT ctuators vailable for all MFT ctuators COVES ZS-T Terminal cover for NEM 2, -T models vailable for all -T Model ctuators (except T) Tech.Doc - 07/17 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 53