+GF+ SIGNET Temperature Transmitter Instructions

Size: px
Start display at page:

Download "+GF+ SIGNET Temperature Transmitter Instructions"

Transcription

1 GF SIGNET 80- Temperature Transmitter Instructions ENGLISH B-/00 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents. Installation. Specifications. Electrical Connections. Menu Functions Temperature Temp Units: C F Relay Relay. Installation The transmitter is available in three versions: a panel mount version, an integral (pipe mount) version, and a universal assembly for installation near the sensor.. Panel Installation The Panel Mounting kits are supplied with the hardware to install instrumentation into panels and maintain a NEMA X watertight seal.. Punch out panel and de-burr edges. Recommended clearance on all sides between instruments is inch.. Place gasket on instrument, and install in panel.. Slide mounting bracket over back of instrument until quick-clips snap into latches on side of instrument.. Connect wires to terminals.. To remove, secure instrument temporarily with tape from front or grip from rear of instrument. DO NOT RELEASE. Press quick-clips outward and remove. gasket latch transmitter panel Liquid Tight Connector (cable gland) terminals mounting bracket quick-clip. Integral Assembly (-80). Punch out conduit ports if necessary.. Connect sensor to integral adapter. Push and twist-lock integral adapter to conduit base and secure with locking ring and screw.. Mount unit in pipe. Route cable through cable gland and connect to transmitter.. Close unit and secure. Seal cable entry.. Universal Assembly (-800). Install transmitter base. Connect wires to transmitter.. Close unit and secure with push and twist lock. Seal cable entry. wires seal seal. Specifications General Compatibility: GF SIGNET -0- or - Temperature Sensors Accuracy: ±0. C Enclosure: Rating: NEMA X/IP front Case: PBT Window: Polyurethane coated polycarbonate Keypad: Sealed -key silicone rubber Weight: Approx. g ( oz.) Display: Alphanumeric x LCD Update rate: second Contrast: User selected, levels Environmental Operating temperature: -0 to 70 C ( to 8 F) Storage temperature: - to 80 C ( to 7 F) Relative humidity: 0 to 9%, non-condensing 80- Temperature Transmitter Instructions Standards and Approvals CSA, CE, UL listed Manufactured under ISO 900 Electrical Sensor Input: Range: -0 to 00 C Current outputs (): to 0 ma, isolated, fully adjustable and reversible : to VDC ±0%, regulated, 0 ma max current Max loop impedance: 0 Ω V, Ω 8 V 00 Ω V Update rate: 00 ms Accuracy: ±0.0 ma Open-collector outputs ( each): Hi, Lo, Pulse Programmable Open-collector, isolated, 0 ma sink or source, 0 VDC max. pull-up voltage Hysteresis: User adjustable Internal open-collector output circuit S Ω Isolation D 8 7 Outputs _ 0 9 page of 8

2 Dimensions Panel Mount 9mm (.8 in.) Field Mount 9 mm (.8 in.) Panel Cutout 9 mm (.8 in.) Optional Rear Cover 9 x 9 mm ( 0.8, - 0 mm). x. in. (0.0, -0 in.) 9 mm (.8 in.) 8 mm (. in.) mm (. in.) mm (. in.) 97 mm (.8 in.) 08 mm (. in.). Electrical Connections Caution: Failure to fully open terminal jaws before removing wire may permanently damage instrument. Wiring Procedure. Remove in. (- mm) of insulation from wire end.. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.. Insert exposed (non-insulated) wire end in terminal hole until it bottoms out.. Release orange terminal lever to secure wire in place. Gently pull on each wire to ensure a good connection. Wiring Removal Procedure. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.. When fully open, remove wire from terminal... - System /Loop. System /Loop. System /.. Description - VDC - VDC ±%, system power and current loop connections. Max. loop impedence: 0 Ω V, Ω 8 V 00 Ω V. Open Collector Output 7. Output 8. Output - 9. Output 0. Output - Preamplifier/Sensor Input. Black (Sensr V). Red (Sensr IN). Silver (Sensr Gnd). Black (Sensr V). Red (Sensr IN). Silver (Sensr Gnd) Open-collector transistor output programmable as: High/Low alarm with adjustable hysteresis Proportional pulse output (0-00 pulses/min) Disable (Off) selection Wiring Tips: Do not route sensor cable in conduit containing AC power wiring - electrical noise may interfere with sensor signal. Routing sensor cabling in grounded metal conduit may prevent moisture damage, electrical noise, and mechanical damage. Seal cable entry points to prevent moisture damage. When placing two wire ends into a single terminal, solder or crimp ends together. System Pwr System Pwr Output - Output Output - Output Snsr Gnd (SHIELD) Snsr IN (RED) Snsr V (BLACK) Snsr Gnd (SHIELD) Snsr IN (RED) Snsr V (BLACK) page of Temperature Transmitter Instructions

3 . System /Loop Connections Stand-alone application, no current loop used Transmitter Loop - NC NC DC - V Connection to a PLC/Recorder, separate supply Transmitter Loop - DC - V PLC or Recorder Channel Channel Channel Channel Connection to a PLC with built-in power supply Transmitter Transmitter Transmitter Loop - Loop- Loop- Loop - Loop- Loop- Loop- Loop - Internal PLC Connection PLC Ground Channel Channel Channel Channel Example: Two transmitters connected to PLC/Recorder with separate power supply DC - V PLC or Recorder - Channel Channel - Channel Channel - Channel Channel - Channel Channel. Sensor Input Connections Wiring Tip: Do not route sensor cable in any conduit containing AC power wiring - electrical noise may interfere with the signal. Silver (Snsr Gnd) Red (Snsr IN) Black (Snsr V) Silver (Snsr Gnd) Red (Snsr IN) Black (Snsr V) GF SIGNET 0 Temperature Sensors. Open Collector Functions Low: Output triggers when process variable is less than setpoint. High: Output triggers when process variable is higher than setpoint. Example: In Low Alarm Mode Operation, the output becomes active when the process drops below the setpoint, and becomes inactive when the process rises above the setpoint plus hysteresis. The opposite is true for High Alarm Mode. Hysteresis Setpoint Process 80- Temperature Transmitter Instructions Output active Output inactive Time Off: Disables output pulse. Proportional Pulse Mode Operation The output emits a 00 ms pulse (simulated contact closure) at rate defined by the Output, Pulse Range, Output Rate, and the process condition (0 to 00 pulses/minute, as programmed) Example: As the process falls below 0 the output will start pulsing in relation to the process value, the max pulse endpoint and the programmed pulses/min. Pulse rate will increase as the process approaches the programmed endpoint. 0 = pulses/min. 7. = 0 pulses/min. = 00 pulses/min. Pulse rate Relay or Relay 00 pulses Output Rate: 00 Pulses/min> Relay : Pulse > 0 Start max. pulse endpoint 0 pulses Process variable page of 8

4 . Differential Mode ( Sensor Inputs Required) The selected open-collector or current output is based on the difference of Sensor minus Sensor. To enable differential mode, the selected output's "Source" selection must be set to differential mode "DF", "DT", or "DP". Sensor - Sensor = Difference. Unit of measure is based on Sensor.. Decimal is based on Sensor. Sensor should be the smallest unit measured or negative values will be generated.. Difference calculated in units only; not percentage. For pressure and temperature transmitters ensure Sensor is equal to ID : Sensor - Sensor Difference = 0 Example: -0 ma Loop Range: 0-0 Loop: =.00 ma Example: Output Output Mode: Low Output Setpoint: 70 Output = ON Sensor (80) Sensor (0) GF SIGNET. Menu Functions VIEW Menu: is displayed during standard operation. Press UP or DOWN buttons to view process parameters. Press UP and DOWN buttons at the same time, to exit any other display and return to VIEW menu. Display will return to VIEW menu in 0 minutes unless a key is pressed. CALIBRATE Menu: contains display setup and output parameters. A security code feature prevents unauthorized tampering. To access CALIBRATE menu: Press button for seconds to display: Press UP, UP, UP, DOWN buttons in sequence to display: CALIBRATE: ---- Enter Key Code CALIBRATE: XXXX Enter Key Code OPTIONS Menu: contains setup and display features for minor display or output adjustments. To access OPTIONS menu: Press button for seconds to display: Press UP, UP, UP, DOWN buttons in sequence to display: OPTIONS: ---- Enter Key Code OPTIONS: XXXX Enter Key Code Menu Tips Right button scrolls to right, from top to bottom row, and allows editing when ">" symbol is shown. In CALIBRATE or OPTIONS menus, the transmitter will continue to measure and control outputs. When > is pressed, the input value is held at the last measured process value. When sensor is not connected, unit will display CHECK SENSOR and any output controlled by sensor will be at. ma or OFF. Example To change date, first enter CALIBRATE menu (Press button for seconds; Press UP, UP, UP, DOWN buttons in sequence) Once in CALIBRATE menu, press UP button time.. Display shows right arrow. Press RIGHT button to display "0" blinking. Press buttons to scroll through numbers.. Press button to save. Display now reads new date LAST CAL: > LAST CAL: LAST CAL: SAVING LAST CAL: GF SIGNET GF SIGNET GF SIGNET GF SIGNET GF SIGNET page of Temperature Transmitter Instructions

5 Menu Functions View Menu Range Calibrate Menu Range Preset Options Menu Range Preset Temp: Temp C Switch ID: Sensor to Random Contrast: - Temp: Temp ( - F) > Sensor to Level > Delta Temp: ± 0 C Temp Units: C C Averaging: Off Off Temp-Temp (± 98 F) C > F Off > Low (secs) Loop Output: -0 ma Set: ± 0 C N/A High(8secs) ma Temperature > Output Active: Low Low Loop Output: -0 ma Loop Source: Temp Temp Low > High ma Temp > Temp Output Active: Low Low Last Cal: to DT (-) Low > High Date Loop Range: C C 0-00 C Loop Adjust:.8 to > 00.0 > - F.00 ma >.0 ma ma (ma) (0 ma) ±99 (DT) Loop Adjust: 9.0 to 0.00 Loop Source: Temp Temp 0.00 ma >.0 ma ma Temp > Temp Loop Adjust:.8 to DT (-).00 ma >.0 ma ma Loop Range: C C 0-00 C Loop Adjust: 9.0 to > 00.0 > - F 0.00 ma >.0 ma ma (ma) (0 ma) ±99 (DT) Test Loop: -0 ma N/A > Output Source: Temp Temp (Output) Test Loop: -0 ma N/A Temp > Temp Temp (Output) > DT (-) Test Output: On or N/A Output Mode: Off Low (Output) > Off Low > Low Hi (Output) Test Output: On or N/A Hi > Off Pulse Low or High Selected Output Setpnt: C C (Output) Settings repeat for Output C > ( - F) C (Output) Output Hys: C C > Pulse Selected Output Range: C -> C.0 ->.0 > ( - F) ->80 C (Start>Endpoint) Output PlsRate: pulses/min > pulses/min pulses/min Last Cal: to > Troubleshooting Display Check Sensor? Value must be 00 or less Process in bounds Relay always activated Relay annunciation SETUP READ ERROR Press Any Key Problem Over or under range No sensor detected You may enter the CALIBRATION and OPTIONS menu to program setpoint values even though Check Sensor? is displayed. Output PULSE mode selected, max pulse rate greater than 00. Hysteresis set too large. Memory fault occurred. Solution Verify Connect sensor Turn power off then back on to recognize sensor Select a pulse rate equal to or less than 00 Re-enter smaller hysteresis value. Press any key to reload presets, then reprogram setpoints. 80- Temperature Transmitter Instructions page of 8

6 page of Temperature Transmitter Instructions

7 80- Temperature Transmitter Instructions page 7 of 8

8 GF SIGNET Signet Scientific Company, 0 Aerojet Avenue, El Monte, CA U.S.A. Tel. () Fax () 7-07 For Worldwide Sales and Service, visit our website: gfsignet.com Or call (in the U.S.): (800) GEORGE FISCHER GF Piping Systems /(A-9/99) English Scientific Company 999 page 8 of 8 Printed in U.S.A. on Recycled Paper 80- Temperature Transmitter Instructions

Signet Flow Transmitter

Signet Flow Transmitter Signet 80- Flow *-80.090-* English -80.090- Rev. L 0/ English WARNING! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents.

More information

ph/orp Transmitter SIGNET

ph/orp Transmitter SIGNET SIGNET 8750- ph/orp Transmitter -8750.090- D-4/0 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents. Installation.

More information

Signet ph/orp Transmitter * *

Signet ph/orp Transmitter * * Signet 8750-3 ph/orp *3-8750.090-3* 3-8750.090-3 Rev. G 0/06 English English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury.

More information

CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury.

CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. SIGNET 8850 Conductivity/Resistivity Transmitter ENGLISH 8850.090 C/0 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury.

More information

Contents 1. Installation

Contents 1. Installation ENGLISH 880.090 D0/0 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents. Installation. Specifications. Electrical

More information

SIGNET 8860 Dual Channel Conductivity/Resistivity Controller

SIGNET 8860 Dual Channel Conductivity/Resistivity Controller OUTPUT OPTION RELAY 3,4 OPEN COLL 3,4 SHLD ISO GND TEMP 1 SGNL 1 SHLD ISO GND TEMP 2 SGNL 2 - OPEN COLL 4 L N 3-8860.090 C 4/03 English CAUTION! Remove power to unit before wiring input and output connections.

More information

Signet Conductivity/Resistivity Transmitter

Signet Conductivity/Resistivity Transmitter Signet 88503 Conductivity/Resistivity Transmitter English *38850.0903* 38850.0903 Rev. G 3/06 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully

More information

Signet Conductivity/Resistivity Transmitter

Signet Conductivity/Resistivity Transmitter Signet 8803 Conductivity/Resistivity Transmitter English *3880.0903* 3880.0903 Rev. K 11/1 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully

More information

Conductivity/Resistivity Transmitter

Conductivity/Resistivity Transmitter 88502 Conductivity/Resistivity Transmitter English *38850.0902* 38850.0902 Rev.H 8/06 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to

More information

CX105 Conductivity/Resistivity Transmitter

CX105 Conductivity/Resistivity Transmitter CX105 Conductivity/Resistivity Transmitter User Manual REV A.15 Sensorex Corporation, USA 11751 Markon Drive Garden Grove, CA. 92841 U.S.A. www.sensorex.com IMPORTANT SAFETY INFORMATION Please read and

More information

Dial-type digital bar graph. LEDs for Open Collector, Relays and Warning Indicator

Dial-type digital bar graph. LEDs for Open Collector, Relays and Warning Indicator Specifications General Input Channels One Input Types Digital (S 3 L) Serial ASCII, TTL level, 9600 bps Frequency Range 0.5 to 1500 Hz Accuracy 0.5% of reading Measurement Types Flow, ph/orp, Conductivity/Resis

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Multiple sensor types supported with one instrument Dial-type digital bar graph Modules are field installable and replaceable

More information

Signet 8900 Multi-Parameter Controller

Signet 8900 Multi-Parameter Controller Signet 8900 Multi-Parameter Controller Member of the ProcessPro Family of Instruments Features Measures Flow, ph, ORP, Conductivity, Pressure, Level and Temperature Multi-language display ¼ DIN enclosure

More information

Signet 9950 Dual Channel Transmitter

Signet 9950 Dual Channel Transmitter Signet 9950 Dual Channel Transmitter Member of the SmartPro Family of Instruments Features One instrument for multiple sensor types Multiple language support for (Gen 2a) or later in Simplified Chinese,

More information

Signet 9950 Dual Channel Transmitter

Signet 9950 Dual Channel Transmitter Signet 9950 Dual Channel Transmitter Member of the SmartPro Family of Instruments Features One instrument for multiple sensor types Multiple language support for Simplified Chinese, English, French, German

More information

Signet 2750 DryLoc ph/orp Sensor Electronics

Signet 2750 DryLoc ph/orp Sensor Electronics Signet 2750 DryLoc ph/ Sensor Electronics Features In-line integral mount and submersible installation versions Automatic temperature compensation Auto configuration for ph or operation In-line 2750 Submersible

More information

8900 Multi-Parameter Controller

8900 Multi-Parameter Controller F L O W + GF + XX DN XX X XX SE N S OR IN PU TS COM M PO RT / O U T O UT RE LA Y 2 RE LA Y 1 RE LA Y RE LA Y S I G N E T L o o p 1 L o o p 2 D a t a 6 1 2 7 8 9 N / C S I G N E T - 2 0 m A I n p u t -808-2

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type digital

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter *3-9900.090* 3-9900.090 Rev. C 08/13 Operating Instructions English Quick Start Look for the Quick Start icon to quickly set up your new 9900. Your new Signet 9900 Transmitter needs

More information

Signet 2751 DryLoc ph/orp Smart Sensor Electronics

Signet 2751 DryLoc ph/orp Smart Sensor Electronics Signet 2751 DryLoc ph/ Smart Sensor Electronics Features Probe health monitoring, glass impedance and broken glass detection Memory chip interface that allows for transferable calibration, runtime data,

More information

Signet 9900 Transmitter

Signet 9900 Transmitter English Signet 9900 Transmitter *3-9900.090* 3-9900.090 Rev. E 06/14 Operating Instructions Quick Start Look for the Quick Start icon to quickly set up your new 9900. Your new Signet 9900 Transmitter needs

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter *3-9900.090* 3-9900.090 Rev. A2 08/11 Operating Instructions English Quick Start Your new Signet 9900 Transmitter needs to be calibrated and the sensor needs to be initialized prior

More information

Signet 9900 Transmitter

Signet 9900 Transmitter Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount NEW! Modbus Module supports RS485 Serial Modbus Communications Multiple sensor types supported with

More information

Signet 2610 Process Optical Dissolved Oxygen Sensor

Signet 2610 Process Optical Dissolved Oxygen Sensor Signet 2610 Process Optical Dissolved Oxygen Sensor *3-2610.090* 3-2610.090 Rev. A 04/12 English Operator's Manual Introduction System Description Your new RDO Pro is a rugged, reliable sensor designed

More information

Local Model. Remote Model FPD1000-A. and FPD1000-TX 4-20 ma Transmitter Local and Remote Models

Local Model. Remote Model FPD1000-A. and FPD1000-TX 4-20 ma Transmitter Local and Remote Models Local Model Remote Model FPD1000-A and FPD1000-TX 4-20 ma Transmitter Local and Remote Models GENERAL INFORMATION This manual will assist you in operating and maintaining your OMEGA 4-20 ma Transmitter.

More information

Self-Powered Counters H7ET

Self-Powered Counters H7ET Self-Powered Counters Subminiature Time Totalizers Require No External Power Supply Subminiature 8 x 2 mm (1.89 x.9 in) Improved noise immunity Screw terminal and wire-wrap types available Printed circuit

More information

Loop Powered Indicator

Loop Powered Indicator Instruction Manual Model PD686 Loop Powered Indicator M397 January 3, 2019 JOWA USA, Inc. 59 Porter Road Littleton, MA 01460-1431 USA Tel: 978-486-9800 Fax: 978-486-0170 PD686 I.S. and N.I. NEMA 4X, IP67

More information

PROCESS & TEMPERATURE CONTROLLERS

PROCESS & TEMPERATURE CONTROLLERS PROCESS & TEMPERATURE CONTROLLERS NOVA PD54 Series Thermocouple, RTD, & Process Inputs High Accuracy Auto-Tuning PID Heating & Cooling Models Universal Power Supply 1-24 VAC Up to 3 Relays & 2 Analog Outputs

More information

KENCO Loop Powered Magnetostrictive Transmitter. KMD SERIES Operation and Installation Manual. Table of Contents

KENCO Loop Powered Magnetostrictive Transmitter. KMD SERIES Operation and Installation Manual. Table of Contents KENCO ENGINEERING COMPANY P.O. BOX 470426, TULSA, OK 74147-0426 PHONE: (918) 663-4406 FAX: (918) 663-4480 http://www.kenco-eng.com e-mail: info@kenco-eng.com KENCO Loop Powered Magnetostrictive Transmitter

More information

Digital flow transmitter for continuous flow measurement

Digital flow transmitter for continuous flow measurement Digital flow transmitter for continuous flow measurement Compact or remote version for DN 06 to 400, PN10 Shows both flow rate and volume (with two totalizers) Automatic-calibration: TEACH-IN Simulation:

More information

M1 Series. Humidity - Temperature Transmitter INSTRUCTION MANUAL

M1 Series. Humidity - Temperature Transmitter INSTRUCTION MANUAL M1 Series Humidity - Temperature Transmitter INSTRUCTION MANUAL 20031110 -2- CONTENTS Overview... 3 Operation... 4 Power supply... 4 Operating range and limits... 4 Temperature compensation of the humidity

More information

User s Guide DPU91 SERIES. Transmitter. Shop online at omega.com For latest product manuals:

User s Guide DPU91 SERIES. Transmitter. Shop online at omega.com   For latest product manuals: TM User s Guide Shop online at omega.com e-mail: info@omega.com For latest product manuals: www.omegamanual.info DPU91 SERIES Transmitter TM omega.com info@omega.com U.S.A. Headquarters: Servicing North

More information

DC Voltage Hawk II H235 Series Advanced Digital Panel Meter

DC Voltage Hawk II H235 Series Advanced Digital Panel Meter % DC Voltage Hawk II H35 Series Advanced Digital Panel Meter Easily Programmed from the Front Panel User-Friendly Software Functions Include: Password Display Scaling Decimal Point Selection Set Point

More information

Digital conductivity transmitter

Digital conductivity transmitter Digital conductivity transmitter Compact version with integrated conductivity electrodes Remote version with seperated transmitter for short (15 ft.) or long (1500 ft.) distance Commissioning is easy due

More information

Ultrasonic Displacement Sensor E4DA

Ultrasonic Displacement Sensor E4DA Sensing Supply voltage Output Ultrasonic beam Ultrasonic Displacement Sensor Sensor s Narrow Ultrasonic Beam Accurately Detects Small Objects, Provides Linear Analog Output For Inspection, Measurement

More information

MODEL: KS. Plug-in Signal Conditioners K-UNIT

MODEL: KS. Plug-in Signal Conditioners K-UNIT Plug-in Signal Conditioners K-UNIT DC ALARM Functions & Features Providing relay contact closures at preset DC input levels Dual (Hi/Lo) trip Multi-turn screwdriver setpoint adjustments Monitor jacks provided

More information

Roline L1 Series. Humidity - Temperature Transmitters INSTRUCTION MANUAL

Roline L1 Series. Humidity - Temperature Transmitters INSTRUCTION MANUAL Roline L1 Series Humidity - Temperature Transmitters INSTRUCTION MANUAL 20030314 CONTENTS Overview... 3 Operation... 5 Power supply... 5 Operating range and limits... 5 Temperature compensation of the

More information

Digital flow ELEMENT transmitter for continuous flow measurement

Digital flow ELEMENT transmitter for continuous flow measurement ELEMENT Transmitter Digital flow ELEMENT transmitter for continuous flow measurement Type can be combined with... PN10, DN15 to DN400 fluidic process connection Programmable outputs : one or two transistor

More information

ph or ORP Transmitter

ph or ORP Transmitter ph or ORP Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma (Process + Temp) Removable backlighted display Universal process connection Compatible with 120 mm ph/ ORP probes

More information

Installation and Operating Instructions. Power IT Power Factor Controller RVC

Installation and Operating Instructions. Power IT Power Factor Controller RVC Installation and Operating Instructions Power IT Power Factor Controller RVC Table of contents Page 1. Read this first... 3 About this Instruction Manual... 3 Safety... 3 Electromagnetic compatibility...

More information

Advanced Ladder Logic Full IEC Languages 25A for <1 24 VDC DC Switched

Advanced Ladder Logic Full IEC Languages 25A for <1 24 VDC DC Switched EXL6 OCS Datasheet for HE- EXL1E0, HE- EXL1E2, HE- EXL1E3, HE- EXL1E4, HE- EXL1E5, HE- EXL1E6 HEXT371C100, HEXT371C112, HEXT371C113, HEXT371C114, HEXT371C115, HEXT371C116 1. Specifications Required Power

More information

Maintenance Information

Maintenance Information 47104302 Edition 1 November 2012 Cordless Drill/Driver QX Series Maintenance Information Save These Instructions Tool Diagnosis 1. Before servicing this unit, you will need a fully charged battery of known

More information

Digital flowmeter for continuous flow measurement

Digital flowmeter for continuous flow measurement 8025 Flowmeter INSERTION Digital flowmeter for continuous flow measurement Compact or remote version for DN06 to DN400, PN10 Displays both flow rate and volume (with two totalizers) On site calibration

More information

Digital flow ELEMENT transmitter for continuous flow measurement

Digital flow ELEMENT transmitter for continuous flow measurement Digital flow ELEMENT transmitter for continuous flow measurement Type 8036 can be combined with... DN06 to DN65 fluidic process connection Programmable outputs : one or two transistor output(s) and single

More information

Digital flowmeter for continuous flow measurement

Digital flowmeter for continuous flow measurement 8025 Flowmeter INSERTION Digital flowmeter for continuous flow measurement Compact or remote version for DN06 to DN400, PN10 Displays both flow rate and volume (with two totalizers) On site calibration

More information

dtrans Lf 01 µp transmitter / controller for electrolytic conductivity

dtrans Lf 01 µp transmitter / controller for electrolytic conductivity M. K. JUCHHEIM GmbH & Co Delivery address:mackenrodtstraße 4, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: 49 66 6003-0 Fax: 49 66 6003-607 E-mail: mail@jumo.net Internet: www.jumo.net

More information

BAPI-Stat 4 X-Combo, Room %RH and Temp. Sensor BA/BS4XC Installation & Operating Instructions

BAPI-Stat 4 X-Combo, Room %RH and Temp. Sensor BA/BS4XC Installation & Operating Instructions Overview and Identification The BAPI-Stat 4 X-Combo () Room Unit features 4 output channels and optional local indication of temperature and humidity. Additional options include Temperature Setpoint, Humidity

More information

OVEN INDUSTRIES, INC. Model 5C7-362

OVEN INDUSTRIES, INC. Model 5C7-362 OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...

More information

Model RFT9709 Transmitter Instruction Manual

Model RFT9709 Transmitter Instruction Manual Model RFT9709 Transmitter Instruction Manual March 1999 Model RFT9709 Transmitter Instruction Manual For technical assistance, phone the Micro Motion Customer Service Department: In the U.S.A., phone

More information

* * Signet 2610 Process Optical Dissolved Oxygen Sensor. Operator's Manual. Introduction. English. System Description.

* * Signet 2610 Process Optical Dissolved Oxygen Sensor. Operator's Manual. Introduction. English. System Description. Signet 2610 Process Optical Dissolved Oxygen Sensor *32610.090* 32610.090 Rev. C 08/13 English Operator's Manual Introduction System Description Your new RDO Pro is a rugged, reliable sensor designed to

More information

Valve Island with Electronic I/O

Valve Island with Electronic I/O Screw in Temperature /Switch with display for ON/OFF Control Indication, monitoring, transmission and ON/OFF control in one device Extra large display Menu guided parametrisation Complete communication

More information

Ultrasonic level transmitter, non-contact

Ultrasonic level transmitter, non-contact Ultrasonic level transmitter, non-contact Type 8175 can be combined with... Compact, remote versions for level measurement up to 10 m Multi language menu control Interference echo filter Automatic calibration:

More information

Analog Signal DIN Fiber Link System

Analog Signal DIN Fiber Link System USER GUDE RLH ndustries, nc. The leader in rugged fiber optic technology. U139 2017C1027 Analog Signal DN Fiber Link System SYSTEM NSTALLATON NFORMATON Description The Analog Signal DN Fiber Link system

More information

AMPSEAL* Automotive Plug Connector and Header Assembly

AMPSEAL* Automotive Plug Connector and Header Assembly AMPSEAL* Automotive Plug Connector and Header Assembly Application Specification 114-16016 17 APR 14 NOTE NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Unless

More information

MODEL: M2DYS SEN TRONIC AG

MODEL: M2DYS SEN TRONIC AG Super-mini Signal Conditioners Mini-M Series CURRENT LOOP SUPPLY Functions & Features Powers a 20 ma DC current loop Short circuit protection Applicable to smart transmitters CE marking UL approval Typical

More information

MODEL: M2SES SEN TRONIC AG [3] OUTPUT

MODEL: M2SES SEN TRONIC AG [3] OUTPUT Super-mini Signal Conditioners Mini-M Series HIGH/LOW SELECTOR Functions & Features Monitors two DC input signals and transmits an output signal proportional to the higher or lower input CE marking UL

More information

GE Sensing. Introduction. Wiring Diagrams (Typical) Field Calibration. Installing the Sensor

GE Sensing. Introduction. Wiring Diagrams (Typical) Field Calibration. Installing the Sensor clear mode enter clear mode enter GE Sensing Introduction The GE Telaire Vaporstat 900 sensor measures in applications in the range of 0 to 0 F dew point. The sensor package is designed for wall mounting.

More information

Signet 9950 Dual Channel Transmitter

Signet 9950 Dual Channel Transmitter English Signet 9950 Dual Channel Transmitter *3-9950.090* 3-9950.090 Rev. 7 02/19 Operating Instructions (see pg. 11) Description 3-9950-1, -2 NOTE: Prior to installation, Check www.gfsignet.com for software

More information

FIELD MOUNTED RATE TOTALISER MODEL 202D

FIELD MOUNTED RATE TOTALISER MODEL 202D FIELD MOUNTED RATE TOTALISER MODEL 202D 1 February 1999 CONTENTS 1. Introduction 1 1.1 Model Number Designation 3 1.2 Intrinsic Safety Considerations 4 2. Specification 6 3. Operation 8 3.1 Display 8

More information

ITP14. Universal process indicator. User guide

ITP14. Universal process indicator. User guide ITP14 Universal process indicator User guide ITP14_2018.05_0279_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover Germany Tel.: +49 (0)

More information

Series 10-ZSE30A(F)/10-ISE30A

Series 10-ZSE30A(F)/10-ISE30A Series 10-ZSEA(F)/10-ISEA RoHS 2-Color Display High-Precision Digital Pressure Switch Clean series For positive For vacuum/ compound Rated range ISEA 0.1 to 1 MPa How to Order 10 ISEA 01 N M 01 N01 C4H

More information

Preset counters, electronic

Preset counters, electronic The Codix 716 / 717 can be used universally. These preset pulse, tachometers or preset timers with up to 2 presets can solve a wide variety of control and monitoring tasks in every application. With their

More information

KOBOLD EchoKing NEO-5003 Series Ultrasonic Level Transmitter User Instructions KOB

KOBOLD EchoKing NEO-5003 Series Ultrasonic Level Transmitter User Instructions KOB KOBOLD EchoKing NEO-5003 Series Ultrasonic Level Transmitter User Instructions KOB KOBOLD Instruments Inc. 1801 Parkway View Drive Pittsburgh PA 15205 Phone (412) 788-2830 Fax (412)-788-4890 Manual-NEO_5003-4_1-17

More information

Wireless Room Temperature and Humidity Transmitter (Units without Temperature Setpoint or Override) Installation and Operating Instructions

Wireless Room Temperature and Humidity Transmitter (Units without Temperature Setpoint or Override) Installation and Operating Instructions Wireless Temperature and Humidity Overview and Indentification The Wireless Temperature and Humidity measures the room temperature and Relative Humidity and transmits the data at 418MHz or 433MHz RF to

More information

Series 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual

Series 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual THE HIGH PERFORMANCE COMPANY Series 70 Hold 1 sec. Hold 1 sec. FOR MORE INFORMATION ON THIS PRODUCT AND OTHER BRAY PRODUCTS PLEASE VISIT OUR WEBSITE www.bray.com Table of Contents 1. Definition of Terms.........................................2

More information

Posiflow Proportional Solenoid Valves % ^ ) 2/2. Brass or Stainless Steel Bodies 1/8" to 1/2" NPT. Proportional Valves. Features.

Posiflow Proportional Solenoid Valves % ^ ) 2/2. Brass or Stainless Steel Bodies 1/8 to 1/2 NPT. Proportional Valves. Features. 4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/8" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Control achieved by applying straight voltage between 0 and 24 VDC

More information

Commercial Vehicle Productivity and Security. Antenna Configuration. External Antenna Installation (model 6650H only) Contigo 6650H/6651H Beacon

Commercial Vehicle Productivity and Security. Antenna Configuration. External Antenna Installation (model 6650H only) Contigo 6650H/6651H Beacon Commercial Vehicle Productivity and Security The 6650H/6651H is a versatile and economical GPS tracking beacon designed for fleet management needs in all commercial vehicles. The H designation in the model

More information

Installing the 3 Indexer: PRS Standard Tools

Installing the 3 Indexer: PRS Standard Tools 888-680-4466 ShopBotTools.com Installing the 3 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Route Cable into Box...5

More information

Level Transmitter / Controller / Indicator. 3-in-1 package that is simple to install and use. With expanded ranges and improved chemical resistance.

Level Transmitter / Controller / Indicator. 3-in-1 package that is simple to install and use. With expanded ranges and improved chemical resistance. Level Transmitter / Controller / Indicator 3-in-1 package that is simple to install and use. With expanded ranges and improved chemical resistance. 2.1 NEW Class 1, Division 1 Hazardous Areas Approved

More information

FLOMID-MX Control unit for electromagnetic flowmeters USERS MANUAL. instrumentación para fluidos. Realitzat: Revisat R+D Electrònic: Aprovat: Data:

FLOMID-MX Control unit for electromagnetic flowmeters USERS MANUAL. instrumentación para fluidos. Realitzat: Revisat R+D Electrònic: Aprovat: Data: instrumentación para fluidos FLOMID-MX Control unit for electromagnetic flowmeters USERS MANUAL Realitzat: Data: Revisat R+D Electrònic: Data: Revisat Of. Comercial: Data: Aprovat: Data: R-MI-Flomid-MX

More information

The transducer component converts the measured signal and displays the actual value.

The transducer component converts the measured signal and displays the actual value. Digital inductive conductivity transmitter System Integration Provides low Total Cost of Ownership PEEK/PPA version for CIP applications TEACH IN and SIMULATION Function Approval PVDF Version PEEK Version

More information

Owner s Manual S10 SERIES ELECTRONIC STEP CONTROLLER WITH VERNIER CONTROL

Owner s Manual S10 SERIES ELECTRONIC STEP CONTROLLER WITH VERNIER CONTROL Owner s Manual S10 SERIES ELECTRONIC STEP CONTROLLER WITH VERNIER CONTROL This manual covers installation, setup, operation and troubleshooting. Read carefully before attempting to install, operate or

More information

Models UT550/UT520 Digital Indicating Controllers User s Manual for Loop Control for Backup

Models UT550/UT520 Digital Indicating Controllers User s Manual for Loop Control for Backup Instruction Manual Models UT550/UT520 Digital Indicating Controllers User s Manual for Loop Control for Backup IM 05D01C02-45E IM 05D01C02-45E 1st Edition Blank Page Introduction Thank you

More information

BATCHMATE 1500 Batch Control Computer Technical Bulletin

BATCHMATE 1500 Batch Control Computer Technical Bulletin TS-5(C) BATCHMATE 5 Batch Control Computer Technical Bulletin DESCRIPTION The BATCHMATE features an 8 digit.55-in. alphanumeric LED display. The pulse input model will accept up to 2, pulses per second

More information

UltraFlo UFDD ULTRASONIC CLAMP-ON FLOW METER

UltraFlo UFDD ULTRASONIC CLAMP-ON FLOW METER UltraFlo UFDD ULTRASONIC CLAMP-ON FLOW METER DESCRIPTION The UltraFlo UFDD Clamp-On Ultrasonic Flow Meter is the ideal flow meter with accurate, easy-to-use, easy-to-install digital doppler technology.

More information

Digital batch controller

Digital batch controller INSERTION Digital batch controller Type 8025 can be combined with... Compact or remote version for DN06 to DN400, PN10 Dosing On site calibration by Teach-In Check of input/output signals Total and daily

More information

Current Loop Interface Module M-2025C

Current Loop Interface Module M-2025C CONTROLS Interface Module M-2025C Current-to-Voltage Analog Converter used with the M-2001 Series Digital Tapchanger Control and M-2948/M-2949 Tap Position Sensors to provide positive tap position knowledge

More information

MODEL: W2DYS SEN TRONIC AG. Mini-MW Series

MODEL: W2DYS SEN TRONIC AG. Mini-MW Series MODEL: WDYS Space-saving Dual Output Signal Conditioners Mini-MW Series CURRENT LOOP SUPPLY Functions & Features Powers a 0 ma DC current loop Short circuit protection Applicable to smart transmitters

More information

HUMITRAN-RHT & RH RELATIVE HUMIDITY/TEMPERATURE TRANSMITTER RELATIVE HUMIDITY TRANSMITTER

HUMITRAN-RHT & RH RELATIVE HUMIDITY/TEMPERATURE TRANSMITTER RELATIVE HUMIDITY TRANSMITTER HUMITRAN-RHT & RH RELATIVE HUMIDITY/TEMPERATURE TRANSMITTER RELATIVE HUMIDITY TRANSMITTER A. GENERAL DESCRIPTION The Tegam Model RH is a relative humidity transmitter; the Model RHT includes a temperature

More information

LT3000 ULTRASONIC LEVEL TRANSMITTER

LT3000 ULTRASONIC LEVEL TRANSMITTER LT3000 ULTRASONIC LEVEL TRANSMITTER Owner s Manual Specifications Installation Calibration Troubleshooting Warranty Drawings Distributed By: iprocessmart.com 14262 Doolittle Drive San Leandro, CA 94577

More information

BS-3520 Digital Indicator

BS-3520 Digital Indicator BS-3520 Digital Indicator The Better Way for Weighing & easurements Table of Contents. Introduction...3 - Trait... 3-2 Warning... 4 2. Specification...5 3. External Size...6 4. Description on Front Panel...7

More information

Programmable transmitter of temperature, relative humidity and other derived humidity values with 4-20 ma outputs Instruction Manual

Programmable transmitter of temperature, relative humidity and other derived humidity values with 4-20 ma outputs Instruction Manual T3110 TRANSMITTER Programmable transmitter of temperature, relative humidity and other derived humidity values with 4-20 ma outputs Instruction Manual Instruction manual for use of T3110 transmitter Transmitter

More information

HLC-1000 High-limit Humidity Control

HLC-1000 High-limit Humidity Control FANs 216, 1628.3 Product/Technical Bulletin HLC-1000 Issue Date 1197 HLC-1000 High-limit Humidity Control The HLC-1000 is designed to limit duct humidity by comparing a controller s request for humidification

More information

RADIO ANTI TWO-BLOCK SYSTEM

RADIO ANTI TWO-BLOCK SYSTEM BB-550 TM RADIO ANTI TWO-BLOCK SYSTEM INSTALLATION MANUAL GREER Company 1918 East Glenwood Place, Santa Ana, CA 92705 Tel: (714) 259-9702 FAX (714) 259-7626 BB-550 TM Radio Anti Two-Block System PN W250000

More information

CMM System - Encapsulated Modules

CMM System - Encapsulated Modules CMM System - Encapsulated Modules Bearing Monitoring BMM-40 BDM-40 BMM-42 BDM-42 DMM-13 DMM-12 SPM 40000 SPM 42000 45011-L (max. 4 m) 45011-L (max.100 m) VMM-14/15 VMM-20/21 VDM-14/15 VDM-20/21 90296-L

More information

Type PLC Fitting. Valve for Continuous control. Diaphragm valve. Output

Type PLC Fitting. Valve for Continuous control. Diaphragm valve. Output Digital Inductive conductivity transmitter Optimal solution for conductivity measurements in difficult fluids (polluted, dirty,...) PEEK/PPA version for CIP applications Large range of process connections

More information

MODEL: AS4V. Plug-in Signal Conditioners M-UNIT

MODEL: AS4V. Plug-in Signal Conditioners M-UNIT Plug-in Signal Conditioners M-UNIT DC ALARM (dual or quad alarm trip; field-configurable) Functions & Features Provides relay outputs at preset DC input levels Quad or dual trip Setting and display in

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual M518 Rev. B Model 1030F Indicator-Totalizer Model 1030F Indicator-Totalizer Installation, Operation and Maintenance Manual Table of Contents General... 1 Installation... 1 Operation... 7 Programming...

More information

Posiflow Proportional Solenoid Valves % ^ ) 2/2. Brass or Stainless Steel Bodies 1/4" to 1/2" NPT. Proportional Valves. Features.

Posiflow Proportional Solenoid Valves % ^ ) 2/2. Brass or Stainless Steel Bodies 1/4 to 1/2 NPT. Proportional Valves. Features. 4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,

More information

General-Purpose Photoelectric Sensor

General-Purpose Photoelectric Sensor General-Purpose Photoelectric Sensor Wide Selection of High Performance Small DC Sensors Offers Longer Sensing Distances Fast 0. msec response time for high-speed sensing Extended sensing distances up

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual TM M723 Rev. C Model 1050 Strain Gage Transmitter Installation, Operation and Maintenance Manual Table of Contents General... 1 Installation... 1 Specifications... 1 Wiring... 2 Setup and Operation...

More information

Signet ph/orp Electrodes General Purpose

Signet ph/orp Electrodes General Purpose Signet 2724-2726 ph/orp Electrodes General Purpose Compatible with ALL Signet ph/orp instruments and SmartPro transmitters Features Patented reference design for exceptional performance and prolonged life

More information

MODEL: M2XPA3. [2] EXCITATION 2: 4 V DC / 20 ma 3: 8 V DC / 20 ma 4: 12 V DC / 20 ma Configurator software is used to change the excitation value.

MODEL: M2XPA3. [2] EXCITATION 2: 4 V DC / 20 ma 3: 8 V DC / 20 ma 4: 12 V DC / 20 ma Configurator software is used to change the excitation value. Super-mini Signal Conditioners Mini-M Series FREQUENCY TRANSMITTER (PC programmable) Functions & Features Converts the output from a pulse-type transducer into a standard process signal PC programmable

More information

DESCRIPTION DIMENSIONS HOW TO ORDER

DESCRIPTION DIMENSIONS HOW TO ORDER ELECTRONIC CONTROLLER: C102X1000 OR MODULATING ELECTRIC HEAT APPLICATIONS 0 to 10 VDC modulating output VDC pulsed modulating output Room or supply control applications DESCRIPTION DIMENSIONS The C102X1000

More information

Magnetostrictive Level Transmitter

Magnetostrictive Level Transmitter Magnetostrictive Level Transmitter Magnetostrictive Level Transmitter Overview Söm-Tek TM The SKMT liquid level transmitter satisfies the demand for an analog communication interface for sightglass (bypass

More information

WLL 170 Photoelectric switches with fibre-optic cable, red light, manual sensitivity adjustment -- DC. Dimensional drawing R1.6 2-R

WLL 170 Photoelectric switches with fibre-optic cable, red light, manual sensitivity adjustment -- DC. Dimensional drawing R1.6 2-R WLL 0 Photoelectric switches with fibre-optic cable, red light, manual sensitivity adjustment -- DC 0... 0 mm Through-beam systems Dimensional drawing R. -R. Scanning distance 0... 0 mm. Proximity systems

More information

Programmable transmitter of temperature, relative humidity and other derived humidity values with 0 to 10 V outputs Instruction Manual

Programmable transmitter of temperature, relative humidity and other derived humidity values with 0 to 10 V outputs Instruction Manual T0213 TRANSMITTER Programmable transmitter of temperature, relative humidity and other derived humidity values with 0 to 10 V outputs Instruction Manual Instruction manual for use of T0213 transmitter

More information