F6/F7...HD/HDU Series Butterfl y Valves

Transcription

1 INSTLLTION N MINTENNE INSTRUTIONS F6/F7...H/HU Series utterfl y Valves

2 F6 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ction 90 rotation Sizes 2 to 12 Type of end fi tting for use with NSI lass 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F650HU ½ 65 F665HU F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU MO ON/OFF Valve Size v F650HU F665HU 2½ F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU F Series M Series M M SY Series 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

3 F6 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) /8-11UN 50 F F665HU 2½ /8-11UN 50 F680HU /8-11UN 50 F6100HU /8-11UN 2*F 50 F6125HU /4-10UN 50 F650HU /8-11UN 50 F665HU 2½ /8-11UN M(X) 50 F680HU /8-11UN 50 F6100HU /8-11UN 50 M(X) F6125HU /4-10UN 50 F6150HU /4-10UN M(X) 50 F650HU /8-11UN 50 F665HU 2½ /8-11UN SY F680HU /8-11UN 50 F6100HU /8-11UN 50 F6125HU /4-10UN SY F6150HU /4-10UN 50 F6200HU /4-10UN 50 F6250HU /8-9UN SY F6300HU /8-9UN 50 Fail Safe Non-Fail Safe imension is compressed, add.125 for relaxed state. F, M and M maximum actuator ambient temperature is 122 F. imensions SY maximum actuator ambient temperature is 150 F. Model SY1 does not have handwheel - override is via 8mm wrench on bottom side of actuator. pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation fl anges and hardware are not included. 07/10 - Subject to change. elimo ircontrols (US), Inc way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. Flow Pattern % OF MXIMUM FLOW F2WUIM % OF VLVE OPENIN US N LTIN MERI 3

4 F7 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 fl anges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed linear ction 90 rotation Sizes 2 to 12 Type of end fi tting for use with NSI 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder fi nish isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 3-way Spring Non-Spring F750HU ½ 65 F765HU F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU MO ON/OFF Valve Size v F750HU F765HU 2½ F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU F Series M M Series SY Series 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

5 0 F7 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750HU /8-11UN F 50 F765HU 2½ /8-11UN 50 2*F F780HU /8-11UN 50 F750HU /8-11UN 50 SY1 F765HU 2½ /8-11UN 50 F780HU /8-11UN 50 F7100HU /8-11UN 50 SY2 F7125HU /4-10UN 50 F7150HU /4-10UN 50 F7200HU /4-10UN SY3 50 F7250HU /8-9UN 50 SY4 F7300HU /8-9UN 50 Fail Safe Non-Fail Safe F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. Model SY1 does not have hand wheel-override is via 8mm wrench on bottom side of actuator. imensions HS WP15 pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way confi guration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware. 8. elimo SY Series actuators are NEM 4X rated. S 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI 5

6 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ction 90 rotation Sizes 2 to 30 Type of end fi tting for use with NSI 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 200 psi (2-12 ), 150 psi (14-30 ) Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F650H ½ 65 F665H F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H MO ON/OFF Valve Size v F650H F665H 2-1/ F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H F Series M M SY Series 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

7 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) /8-11UN F 200 F665H 2½ /8-11UN 200 F680H /8-11UN 2*F 200 F650H /8-11UN 200 M(X) F665H 2½ /8-11UN 200 F680H /8-11UN M(X) 200 F6100H /8-11UN 2*M(X) 200 Valve Size v 90 v 60 (Max) (Max) (Max) (Max) H No. of Holes Lug olt ctuator lose-off (PSI) /8-11UN 200 F665H 2½ /8-11UN 200 F680H /8-11UN SY2 200 F6100H /8-11UN 200 F6125H /4-10UN 200 F6150H /4-10UN SY3 200 F6200H /4-10UN 200 F6250H /8-9UN SY4 200 F6300H /8-9UN 200 F6350H UN SY5 150 F6400H UN SY6 150 F6450H /8-7UN 150 SY8 F6500H /8-7UN 150 F6600H /4-7UN SY F6750H /4-7UN SY Fail Safe Non-Fail Safe Non-Fail Safe imension is compressed, add.125 for relaxed state. SY6 and larger available in 110/220 V versions only. F, M and M maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. imensions F2WUIM pplication Notes 07/10 - Subject to change. elimo ircontrols (US), Inc. 1. Valves are rated at 200 psi differential pressure in the closed position (SY psi 14 +). 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. Flow Pattern % OF MXIMUM FLOW % OF VLVE OPENIN US N LTIN MERI 7

8 F7 H utterfly Valves 2 24 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 fl anges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Fail safe operation is possible with NSV-SY series battery backup systems. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed linear ction 90 rotation Sizes 2 to 24 Type of end fi tting for use with NSI 125/150 fl anges Materials: ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 200 psi (2-12 ), 150 psi (14-24 ) Rangeability 10:1 (for 30 to 70 range) Maximum Velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F750H ½ 65 F765H F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H MO ON/OFF Valve Size v F750H F765H 2½ F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H F Series M M Series SY Series 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

9 F7 H utterfly Valves 2 24 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750H /8-11UN F 200 F765H 2½ /8-11UN 2*F 200 F750H /8-11UN 200 F765H 2½ /8-11UN 200 SY2 F780H /8-11UN 200 F7100H /8-11UN 200 F7125H /4-10UN 200 SY3 F7150H /4-10UN 200 F7200H /4-10UN 200 SY4 F7250H /8-9UN 200 F7300H /8-9UN SY5 200 F7350H UN SY6 150 F7400H UN SY7 150 F7450H /8-7UN 150 SY9 F7500H /8-7UN 150 F7600H /4-7UN SY Fail Safe Non-Fail Safe 07/10 - Subject to change. elimo ircontrols (US), Inc. F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. SY6 and larger available in 110/220 V versions only. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way confi guration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. elimo SY Series actuators are NEM 4X rated. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware Way onfi guration odes MSTER Note: For tee confi guration, please refer to page 4. SLVE ON/OFF OR ONFI MO@2V MSTER MSTER VLVE OE VLVE FIL X10 OPEN NON-FIL X11 OPEN OPEN X12 OPEN LOSE X13 LOSE NON-FIL X14 LOSE OPEN X15 LOSE LOSE X Specifies i-irectional Flow apability OMMON ONFI OE X20 X21 X22 X23 X24 X25 OMMON SLVE ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE MSTER MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE SLVE ONFI OE X30 X31 X32 X33 X34 X35 OMMON ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE imensions MSTER MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE NOTES 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of fi eld logic. 5. Proportional actuator normal position is a function of the W/W switch. 6. ll 3-way assemblies are designed for 90 degree actuator rotation. ORERIN INFORMTION Please note that H series F valves over 18 and LL sizes 3-way tee assemblies ordered with onfiguration odes are special order/custom built and are NOT returnable. HS W US N LTIN MERI 9

10 Wire Size vs. Length of Run for SY Series ctuators SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V The NE mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. o NOT mix LSS 1 & LSS 2 circuits in the same conduit. enerally, 24 V actuators over 100 V should be changed to 120 V models. 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

11 Interface Wiring etail SYx-MFT, 24V, 120/230V ctuators: SYx-MFT INSTLLTION NOTES UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. P Tool Service Jack onnection ontrol Signal + ontrol Signal - FK + FK - Power Supply om - Power Supply Hot + daption irection of Rotation 24V 07/10 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal + ontrol Signal - FK + FK - N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption irection of Rotation 120/230V US N LTIN MERI 11

12 SYx-P Interface Wiring etail Open LE losed LE Sensitivity VR2 VR1 ip Switch N Supply H - SI + IN - F + OUT Sensitivity switchsetting is position #3 for factory default. To widen deadband, select a higher number (up to 9). INSTLLTION NOTES UTION Notes: 1. pplicable to the SY1 and legacy SY2-12 actuators. 2. o not change sensitivity or dip switch settings with power applied! 3. VR1 and VR2 are factory calibrated and should not be moved. 4. Motor MS have been factory calibrated and should not be moved. ip Switch Settings OFF ON INPUT = 2-10 V OFF ON RESPONSE = IRET OFF INPUT = 4-20m OFF RESPONSE = REVERSE ON ON WRNIN Potentiometer (Factory Pre-set) OFF ON OFF ON OFF ON INPUT = 1-5 V OUTPUT = 4-20m OUTPUT = 2-10 V For 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k 9, 10 0k When a valve is opened: 8, 9 0k 9, 10 1k OFF ON OFF ON OFF ON LOSS OF SINL = LOSE (irect cting) LOSS OF SINL = OPEN (Reverse cting) LOSS OF SINL = OPEN (irect cting) LOSS OF SINL = LOSE (Reverse cting) LOSS OF SINL = STOP 07/10 - Subject to change. elimo ircontrols (US), Inc. *On modulating actuators O NOT master/ slave using optional potentiometer. For modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k 9, 10 0k When a valve is opened: 8, 9 0k 9, 10 1k US N LTIN MERI

13 SY Series Non-Spring ctuators UTION Electrical Travel djustment (Factory Pre-set) SY-1 Factory pre-set see chart below. Field adjustable if required uxiliary Switch for losed Indication LS2 LS1 uxiliary Switch for Opened Indication Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE lockwise ecrease losed ngle ounter-clockwise Increase losed ngle LS1 OPEN lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle UTION Electrical Travel djustment SY-2-12 Factory pre-set see chart below. Field adjustable if required uxiliary Switch for losed Indication uxiliary Switch for Opened Indication 07/10 - Subject to change. elimo ircontrols (US), Inc. WRNIN F E LS2 LS1 Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE LS1 OPEN lockwise ecrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle Switches at left are shown with actuator fully open F - E INSTLLTION NOTES UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. For the SYx-MFT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release US N LTIN MERI 13

14 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 120/230V ctuators: SY1-24 SY1-110 SY SY W546 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. NOTES SY Each actuator should be powered by a single, isolated 33 control transformer. using a common control signal input. Required: INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES SY (220) aution: Power Supply Voltage using a common control signal input. Required: V Transformer round 120 and 230 V round Line Volts Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 E F HTR - (Open Indication) -F (losed Indication) ontact Rating: V Max. SY N L1 H L2 Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 HTR E F - (Open Indication) -F (losed Indication) ontact Rating: V Max. SY (220) 07/10 - Subject to change. elimo ircontrols (US), Inc. E - (Open Indication) ontact Rating: V Max V Max. E - (Open Indication) ontact Rating: V Max V Max. F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements US N LTIN MERI

15 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY1-24P SY1-110P SY1-220P W547 Hazard Identification this manual. Read these carefully. UTION may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTES PPLITION NOTES round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1 24P Each actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. NOTES SY1 110P (220P) aution: " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately V Transformer round 120 and 230 V round Line Volts 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot ontrol signal 34 6 ontrol Signal (-) 7 ontrol Signal (+) 8 ontrol signal 34 6 ontrol Signal (-) 7 ontrol Signal (+) 8 07/10 - Subject to change. elimo ircontrols (US), Inc. Feedback Feedback (-) 12 Feedback (+) E F SY1-24P Feedback Feedback (-) 12 Feedback (+) E F SY1-110P (220P) US N LTIN MERI 15

16 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY MFT SY MFT SY MFT Hazard Identification this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTES PPLITION NOTES round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. W547-2 NOTES SY MFT Each actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. NOTES SY MFT (230MFT) aution: P Tool Service Jack ontrol Signal Feedback ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V Feedback Signal (-) Not Used daption 8 9 Not Used - 2 Y2 Y1 SYx-24MFT 10 ontrol Signal Feedback PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - Y 1 U P Tool Service Jack daption N L Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) ddress 07/10 - Subject to change. elimo ircontrols (US), Inc. E PE SYx-120MFT SYx-230MFT Y1 Y F SY MFT SY MFT (230MFT) US N LTIN MERI

17 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 110/120/230V ctuators: SY SY SY Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 24 V Transformer round ctuator 120 and 230 V round ctuator Line Volts Open lose K1 K1-1 ommon 3 Open 4 losed HTR N L1 H L2 Open lose K1 K1-1 ommon 3 Open 4 losed HTR E F - (Open Indication) -F (losed Indication) ontact Rating: V Max. E F - (Open Indication) -F (losed Indication) ontact Rating: V Max. 07/10 - Subject to change. elimo ircontrols (US), Inc. K1- SY round ctuator 1 ommon 3 Open 4 losed HTR - (Open Indication) E -F (losed Indication) F ontact Rating: V Max. K1- SY (220) round ctuator 1 ommon 3 Open 4 losed HTR - (Open Indication) E -F (losed Indication) F ontact Rating: V Max. SY SY (220) E - (Open Indication) ontact Rating: V Max V Max. E - (Open Indication) ontact Rating: V Max V Max. F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements US N LTIN MERI 17

18 Wiring for ontrol Valves Proportional, 24V ctuators: SY1-24P W550 Hazard Identification 33 Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. 24 V Transformer Line Volts 35 Feedback () 36 round ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) Feedback (-) 12 Feedback (+) E F - (Open Indication) ontact Rating: V Max V Max. -E (losed Indication) SY1-24P Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) V Transformer round ctuator NOTES SY1-24P Each actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. power applied PPLITION NOTES Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Line Volts ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) Feedback (-) 12 Feedback (+) E F - (Open Indication) ontact Rating: V Max V Max. -E (losed Indication) 07/10 - Subject to change. elimo ircontrols (US), Inc. SY1-24P US N LTIN MERI

19 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MFT W550-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed NOTES SY MFT Each actuator should be powered by a single, isolated control transformer. PPLITION NOTES Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. 36 Use of feedback is optional. ctuator P Tool Service Jack ontrol Signal (+) ontrol Signal (-) Y 1 /- ~/+ Power Supply om Power Supply Hot 24V Feedback Feedback Signal (+) U5 ddress 33 07/10 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal - (Open Indication) 36 Feedback Feedback Signal (-) Not Used - Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used ctuator Y 1 U daption Y1 Y2 P Tool Service Jack ddress daption Y1 Y2 SYx-24MFT SYx-24MFT /- ~/ Power Supply om Power Supply Hot 24V 33 E F -F (losed Indication) ontact Rating: V Max. PE SY2 5-24MFT US N LTIN MERI 19

20 Wiring for ontrol Valves Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P W552-1 Hazard Identification 120 and 230 V round Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Feedback () Feedback (-) 12 Feedback (+) E F ctuator - (Open Indication) ontact Rating: V Max V Max. -E (losed Indication) SY1-110P (220P) PPLITION NOTES round ctuator Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1-110P (220P) aution: Power supply voltage. power applied. ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) Feedback (-) 12 Feedback (+) E F - (Open Indication) ontact Rating: V Max V Max. -E (losed Indication) 07/10 - Subject to change. elimo ircontrols (US), Inc. SY1-110P (220P) US N LTIN MERI

21 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MFT SY MFT W552-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions PPLITION NOTES Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY MFT (230MFT) aution: Power supply voltage. Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) N L ontrol Signal (+) Y P Tool Service Jack 1 ontrol Signal (-) 1 2 Feedback 36 Feedback Signal (+) Feedback Signal (-) Not Used - U Not Used - 2 daption ddress 8 07/10 - Subject to change. elimo ircontrols (US), Inc. E F ontrol Signal - (Open Indication) -F (losed Indication) ontact Rating: V Max. Feedback PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE ctuator Y 1 U ctuator P Tool Service Jack SYx-120MFT SYx-230MFT daption SYx-120MFT SYx-230MFT N L Y1 9 Y2 10 Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) ddress 8 Y1 9 Y2 10 SY MFT SY MFT US N LTIN MERI 21

22 F ctuators, On/Off imensions with 2-Way Valve F2WUIM_ H Models F24 US F24-S US F120 US F120-S US w/built-in ux. Switches w/built-in ux. Switches Technical ata ontrol on/off Power consumption F24(-S) US running 5 W holding 1.5 W F120(-S) US running 6 W holding 2.3 W Transformer sizing 10 V, class 2 power Electrical connection 3 ft, 18 appliance cables (-S model has 2 cables) ½ conduit connector Electrical protection 120 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank Running time control 150 sec. independent of load spring < 20 sec. mbient temperature -22 F to 122 F [-30 to 50 ] Housing NEM 2 / IP54 gency listings UL 873, S 22.2 No. 24 certifi ed, E Noise level max. 45 d() F...-S US uxiliary switches 2 x SPT, V, UL listed, one switch is fixed at +5, one is adjustable 25 to 85 (double insulated) imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP /10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

23 10 10 F ctuators, On/Off imensions with 3-Way Valve HS WP11 p j y 24 V Transformer Line Volts 1 ommon 2 + Hot 3 W194 F24 US 2 On/Off Wiring W195-UX imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU uxiliary Switches Wiring iagrams 07/10 - Subject to change. elimo ircontrols (US), Inc. 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 V. 4 For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPT, V, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury US N LTIN MERI 23

24 10 10 F ctuators, Multi-Function Technology imensions with 2-Way Valve F2WUIM_ Models FX24-MFT-X1 FX24-MFT-S-X1 w/built-in ux. Switches Technical ata Power supply 24 V, +/- 20%, 50/60 Hz 24 V, +20% / -10% Power running 7.5 W consumption holding 3 W Transformer sizing 10 V (lass 2 power source) Electrical connection FX... 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] 18 appliance or plenum cables, with or without 1/2 conduit connector -S models: two 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] appliance cables with or without 1/2" conduit connectors Overload protection electronic throughout 0 to 95 rotation Operating range Y* 2 to 10 V, 4 to 20 m (default) variable (V, PWM, floating point, on/off) Input impedance 100 kω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for PWM, floating point and on/off control Feedback output U* 2 to 10 V, 0.5 m max Torque minimum 180 in-lb (20 Nm) irection of spring reversible with cw/ccw mounting rotation* motor reversible with built-in switch Mechanical 95 (adjustable with mechanical end stop, 35 to 95 ) angle of rotation* Running time spring <20 -4 F to 122 F [-20 to 50 ]; < F [-30 ] motor* 150 seconds (default), variable (70 to 220 seconds) ngle of Rotation off (default) adaptation Override control* min position = 0% mid. position = 50% max. position = 100% Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 5 mm hex crank (³ ₁₆" llen), supplied Humidity max. 95% RH, non-condensing mbient temperature -22 to 122 F (-30 to 50 ) Storage temperature -40 to 176 F (-40 to 80 ) Housing NEM 2, IP54, Enclosure Type 2 Housing material zinc coated metal and plastic casing Noise level 40d() 150 seconds, run time dependent 62d() spring return gency listings culus acc. to UL /-2-14, N/S E :02, E acc. to 2004/108/E & 2006/95/E Quality standard ISO 9001 Servicing maintenance free Weight 4.6 lbs. (1.9 kg), 4.9 lbs. (2 kg) with switch * Variable when configured with MFT options Rated Impulse Voltage 800V, Type of action 1. (1.. for -S version), ontrol Pollution egree 3. Programmed for 70 sec motor run time. t 150 sec motor run time, transformer sizing is 8.5 V and power consumption is 6 W running / 3 W holding. FX24-MFT-S-X1 uxiliary switches 2 x SPT V, UL approved one set at +10, one adjustable 10 to 90 H imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU HS WP11 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

25 F ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. ontrol signal may be pulsed from either the Hot (Source) or 6 ommon (Sink) 24 V line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. The Z-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. V/4-20 m PWM W399_utterfly W399_utterfly 24 V Transformer Master 5 Master_Slave W399_utterfly Line Volts 3 ontrol Signal 2 to 10 V ( ) (+) lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V On/Off control 07/10 - Subject to change. elimo ircontrols (US), Inc. W W Slave 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U W W Floating Point control W399_utterfly W600_F_FX Master/Slave F24-MFT-S FX24-MFT-S-X1 FX24-MFT-S uxiliary Switches for FX24-MFT-S-X US N LTIN MERI 25

26 10 K24-3-X1 ctuators, On/Off, Floating Point imensions with 2-Way Valve M_M_LineRevised H Technical ata Power supply Power consumption Transformer sizing Electrical connection Overload protection Operation range Y Input impedance Feedback output U K24-3-X1 24V ±20% 50/60Hz 24V ±10% 12W (3W) 21V (class 2 power source) 18 plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] electronic throughout 0 to 95 rotation on/off, fl oating point 100kΩ (0.1 m), 500Ω 1500Ω (fl oating point, on/off) 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication refl ective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 150 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H K F680H F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H M F765H 2½ F780HU F SHP F SHP 2½ F SHP F SHP Single_utterfl y 0 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

27 K24-3-X1 ctuators, On/Off, Floating Point Electrical Installation Wiring iagrams Wiring diagram Note onnect via safety isolation transformer.! Parallel connection of other actuators possible. Note performance data for supply. able lengths T ~ T ~ Y U Y U L V V L tot 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 V Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators N L 230 V 24 V T Y L 1 U Meets UL requirements without the need of an electrical ground connection. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. L 1 Note There are no special restrictions on installation if the supply and data cable are routed separately NOTE: Wiring diagrams shown are for single actuator mounted solutions able colors: 1 = black 2 = red 3 = white 5 = orange = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mm 2 ) L2 = ustomer cable Ltot = Maximum cable length ross section L2 Max. cable length Example for Ltot t = L1 + L2 / 0.75 mm 2 <30 m <5 m 1 m (L1) + 4 m (L 2) 1.00 mm 2 <40 m <8 m 1 m (L1) + 7 m (L 2) 1.50 mm 2 <70 m <12 m 1 m (L1) + 11 m (L 2) 2.50 mm 2 <100 m <20 m 1 m (L1) + 19 m (L 2) T ~ = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mmm 2 ) W399_10 07/10 - Subject to change. elimo ircontrols (US), Inc. On/Off control W399_10 Floating Point control US N LTIN MERI 27

28 10 KX24-MFT-X1 ctuators, Multi-Function Technology imensions with 2-Way Valve M_M_LineRevised H Technical ata Power supply Power consumption Transformer sizing Electrical connection Overload protection Operation range Y Input impedance Feedback output U KX24-MFT-X1 24V ±20% 50/60Hz 24V ±10% 12W (3W) 21V (class 2 power source) 18 plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] electronic throughout 0 to 95 rotation 2 to 10 V, 4 to 20m (default) variable (V,PWM, fl oating point, on/off) 100kΩ (0.1 m), 500Ω 1500Ω (PWM, fl oating point, on/off) 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication refl ective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 95 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H K F680H F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H K F780HU F SHP F SHP 2½ F SHP Single_utterfl y 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

29 KX24-MFT-X1 ctuators, Multi-Function Technology Wiring iagrams 1 Provide overload protection and disconnect as required. W399_utterfly 3 ctuators may also be powered by 24 V. 4 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. 5 ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. 8 ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. 9 For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Meets UL requirements without the need of an electrical ground connection. V/4-20 m W399_utterfly The Z-R Ω resistor may be used. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. NOTE: Wiring diagrams shown are for single actuator mounted solutions PWM W399_utterfly 07/10 - Subject to change. elimo ircontrols (US), Inc. On/Off control W399_utterfly Floating Point control US N LTIN MERI 29

30 10 M Series ctuators, On/Off, Floating Point imensions with 2-Way Valve M_M_LineRevised H Models M24-3-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 2.0 W holding 0.2 W Transformer sizing 5.5 V (class 2 power source) Electrical connection 3 ft, 18 plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol on/off, fl oating point Input impedance 600 Ω ngle of rotation 95, adjustable with mechanical stop irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 95 seconds Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE (and 2006/95/E for line voltage and/or -S versions) Noise level <45d() Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F650H(U) F665H(U) 2½ F680HU imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ Single_utterfl y 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

31 M Series ctuators, On/Off, Floating Point Wiring iagrams j y 24 V Transformer W557_10 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 4 ctuators may also be powered by 24 V. Line Volts a open a closed The indication of direction is valid for switch position 1. a lk (1) ommon Red (2) + Wht (3) M24-3-X1 Meets culus or UL and S requirements without the need of an electrical ground connection. On/Off control WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 24 V Transformer lk (1) ommon Red (2) + Wht (3) + W557_10 The indication of direction is valid for switch position M24-3-X1 Floating Point or On/Off control 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI 31

32 10 M Series ctuators, Multi-Function Technology imensions with 2-Way Valve M_M_LineRevised H Models MX24-MFT-X1 imensions (Inches) Valve Size (Max) H F650H(U) F665H(U) 2½ F680HU Non-Fail Safe (psi) Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4 W holding 1.25 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range Y 2 to 10 V, 4 to 20 m (default) Variable (V, PWM, Floating Point, On/Off) Input impedance 100k Ω (0.1 m), 500 Ω 1500 Ω (PWM, Floating Point, On/Off) Feedback output U 2 to 10 V, 0.5 m max V Variable ngle of rotation 95 electronically variable irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 150 seconds (default) variable (90 to 350 secs) Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE Noise level <45d() Quality standard ISO 9001 Rated impulse voltage 4kV, ontrol pollution degree 3, Type of action 1 imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ Single_utterfl y 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

33 M Series ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection. The Z-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Two Position Line Volts 24 V/ Transformer Position ( ) Feedback V (+) Line Volts 24 V Transformer to 10 V Feedback Signal 11 a irection of rotation switch W W W W lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V W558_utterfly W558_utterfly Floating Point Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W558_utterfly W W V/4-20 m 07/10 - Subject to change. elimo ircontrols (US), Inc. PWM Line Volts 24 V Transformer ( only) Position Feedback V ( ) (+) 8 lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W558_utterfly US N LTIN MERI 33

34 M24-3-X1 ctuators, On/Off, Floating Point imensions with 2-Way Valve M_M_LineRevised H Models M24-3-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.0 W holding 2 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft, 18 appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal On/Off, Floating Point Input impedance 600 Ω ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 sec. Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d () Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H M 2*M F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP /10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

35 M24-3-X1 ctuators, On/Off, Floating Point imensions with 3-Way Valve Wiring iagrams UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H M 2*M F765H 2½ F780H F780HU F7100H F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP Meets culus or UL and S requirements without the need of an electrical ground connection. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off Line Volts 24 V Transformer a open a closed The indication of direction is valid for switch position 1. j y 24 V Transformer a lk (1) ommon Red (2) + Wht (3) M24-3-X1 W559 W559 07/10 - Subject to change. elimo ircontrols (US), Inc. Floating Point Line Volts The indication of direction is valid for switch position 1. lk (1) ommon Red (2) + Wht (3) M24-3-X US N LTIN MERI 35

36 MX24-MFT-X1 ctuators, Multi-Function Technology imensions with 2-Way Valve M_M_LineRevised Models MX24-MFT-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.5 W holding 2 W Transformer sizing 7 V (class 2 power source) Electrical connection 3 ft, 18 appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal 2 to 10 V, 4 to 20 m (with 500 Ω, 1/4 W resistor) Z-R01 Input impedance 100 k Ω for 2 to 10V (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PWM 1500 Ω for on/off and fl oating point ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 sec. Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d () Servicing maintenance free Quality standard ISO 9001 H imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H M 2*M F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H M 2*M F765H 2½ F780H F780HU F7100H F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP /10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

37 MX24-MFT-X1 ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V ctuators with plenum rated cable do not have numbers on wires; use color coded instead. ctuators with appliance rated cable use numbers. ontrol signal may be pulsed from either the Hot (Source) or ommon (Sink) 24 V line. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W W W545_No_2 V/4-20 m 07/10 - Subject to change. elimo ircontrols (US), Inc. Meets culus or UL and S requirements without the need of an electrical ground connection. ontact closures & also can be triacs. & should 9 both be closed for triac source and open for triac sink. Position feedback cannot be used with a Triac sink controller. The 11 actuator internal common reference is not compatible. WRNIN Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 3 ontrol Signal 2 to 10 V 24 V Transformer ( ) (+) Master lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave 5 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Master_Slave Two Position Floating Point PWM Line Volts 24 V/ Transformer Position ( ) Feedback V (+) Line Volts Line Volts 24 V Transformer 8 2 to 10 V Feedback Signal 9 11 W W 5 a irection of rotation switch W W 5 24 V Transformer ( only) Position Feedback V ( ) (+) 8 3 lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y 1 Input Pnk (4) Y 2 Input Org (5) U Output 2 to 10V lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W545_No_2 W545_No_2 W545_No_2 W W Master/Slave US N LTIN MERI 37

38 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves H(U) Series utterfly Valves Storage of utterfly Valve ssemblies ssemblies must be stored indoors, protected from the elements. Materials received on job sites that have long installation lead times should receive extra protection from construction damage. Resilient seats must be protected from abrasion, cutting and nicking, as this will damage the liner and may cause flange area leaks. Electric actuators cannot be stored in wet, damp or caustic areas. o not store construction material on top of valve assemblies. Installation Practices H(U) series butterfly valves are designed to be installed between NSI 125/150 flat-faced, raised face, slip-on or weld neck flanges. Valve should be installed a minimum of 10 pipe diameters from upstream or downstream elbows, strainers, pumps, etc. For chilled water, condenser water or hot water applications, the valve should be installed with the stem in a vertical orientation, with the actuator mounted above the valve. For applications in which there is a possibility of sediment in the flow, the valve should be installed with the stem in a horizontal position and the bottom of the disc should close FROM the downstream side, rather than from the upstream side. Make sure the flange faces are clean and free of rust, scale and debris to prevent damage to the liner face. o NOT use flange gaskets on H(U) series F valves. (Fig. 1a) Follow the recommended flange bolting sequence. (Fig. 8, pg. 85) When installing in Victaulic piping systems, use Victaulic 41 series flange nipples. Installation using Welded Flanges Mount flanges on both sides of valve body and install bolts to properly align valve body and both flanges. Install the valve with the disc in the lmost losed position (Fig. 1) o not use any flange gaskets (Fig. 1a) Make sure the valve liner and flange internal diameters are in alignment. (Fig. 2) Take valve body / flange pair assembly and align with piping ends. TK weld the flanges to the piping in several places. (Fig. 3a) o NOT seam weld at this time! Remove the lug bolts and carefully remove the valve body from the flanges. Seam weld the entire flange / piping connection for both flanges. (Fig 3b) Let the piping components cool completely before re-inserting the valve body. (Fig. 4) WRNIN! Seam welding with the valve body installed between the flanges can damage the liner due to heat migration through the flange to the valve body. 07/10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI

39 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves H(U) Series utterfly Valves 1Fig. 1 1Fig. 3a Fig. 1 3b Fig. 1a 1Fig. 4 07/10 - Subject to change. elimo ircontrols (US), Inc. 1Fig. 2 > US N LTIN MERI 39

40 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves FLNE OLTIN REOMMENTIONS Flange etail for NSI 16.5 Pipe Flanges FLNES RILLIN OLTIN Nominal iameter of iameter of Number olt ircle olt Holes of olts Pipe Size Flange iameter Flange Thickness iameter of olts 2 6 3/4 4-3/4 3/4 4 5/8 2-1/2 7 7/8 5-1/2 3/4 4 5/ /2 15/16 6 3/4 4 5/ /16 7-1/2 3/4 8 5/ /16 8-1/2 7/8 8 3/ /2 7/8 8 3/ /2 1-1/8 11-3/4 7/8 8 3/ / / / / / /8 18-3/4 1-1/ /2 1-7/ /4 1-1/ /8 22-3/4 1-1/ / /2 1-11/ / / /8 29-1/2 1-3/ /4 PRE-INSTLLTION PROEURE 1. Remove any protective fl ange covers from the valve. 2. Inspect the valve to be certain the waterway is free from dirt and foreign matter. e certain the adjoining pipeline is free from any foreign material such as rust and pipe scale or welding slag that could damage the seat and disc sealing surfaces. 3. ny actuator should be mounted on the valve prior to installation to facilitate proper alignment of the disc in the valve seat. 4. heck the valve identifi cation tag for materials, and operating pressure to be sure they are correct for the application. WRNIN! Personal injury or property damage may result if the valve is installed where service conditions could exceed the valve ratings. 5. heck the flange bolts or studs for proper size, threading, and length. 6. These valves are designed to be installed between SME/NSI lass 125/150 fl anges. 7. arefully follow installation using welded fl anges on page 82 of this document. 8. Follow SME fl ange alignment standards: SETION LINMENT a. PIPIN ISTORTIONS: ny distortion of piping to bring into alignment for joint assembly which introduces a detrimental strain in equipment or piping components is prohibited. b. FLNE JOINTS: efore bolting up, flange faces shall be aligned to the design plane within 1/16 /ft measured across any diameter; flange bolt holes shall be aligned within 1/8 maximum offset. 9. When observed during assembly, the fl ange faces shall be parallel within 1 degree, and the force required to align pipe axes shall not exceed 10 lb/ft per inch of NF bolts and nuts shall be fully engaged. FLNE OLTIN REOMMENTIONS Lug Valves, 2-30, NSI 125/150 olt Pattern Valve Size Thread Size Number Required olt Length Semi-Lug utterfl y (inches) 2 5/ /2 5/ / / / / / / / / / / / /10 - Subject to change. elimo ircontrols (US), Inc US N LTIN MERI