Paddle wheel flow controller for On/Off control

Transcription

1 addle wheel flow controller for On/Off control Type 8032 compact Type 8032 can be combined with... Type 8032 remote Indication, monitoring, transmitting and On/Off control in one device. rogrammable outputs (Transistor or relay) utomatic calibration: TECH IN Communication external setpoints and/or process value (4 20 m) or S interface pprovals: Type 2702 (8630) Type 1067 Type 8644 irline Type 8030 Control valve with TopControl Continuous SideControl Valve Island with electronic I/O Only with 8032 remote This intelligent paddle-wheel switch with display is designed for use in clear, neutral or aggressive liquids and specially to switch a valve and to establish a monitoring system or an On/Off control loop. The switching points can be programmed with the 3 key keypad under the display or optionally, for the compact 8032 only, from an external source over a 4 20 m loop. Fitting data ipe diameter 1/4 2 1/2 (N 6 up to N 65) Measuring range 1.0 f/s up to 32.8 f/s (0.3 m/s up to 10 m/s) Fitting Type S030 (see corresp. data sheet) Sensor element addle wheel of the fi tting S030 Materials wetted parts VF, ceramic Medium data Medium temperature (max.) Fluid pressure max. Viscosity 32 F up to 122 F (with VC fi tting) 32 F up to 176 F (with fi tting) 32 F up to 212 F (with Stainless steel, brass, VF fi tting) 140 SI (N10) (with plastic fi tting) 230 SI (N16) (with metal fi tting) 300 cst. Electronic module data Switching accuracy Teach In ±1% fs. Standard K factor ±1% fs., ±3% of measured value rogramming mode Threshold, window or hysteresis Repeatability 0.4% Voltage supply 8032 compact VC 8032 remote epends on the remote sensor: 8041 > VC 8020; 8030 > VC other > min.12 VC, max. 30 VC Reversed polarity of C rotected Outputs transistor 8032 remote e NN and N, 700 m, 30 VC max. Outputs 8032 Transistor (programmable) NN and N, open collector, 5 30 VC, 700 mmax. protected against short circuits Relay (programmable) 3/250 VC or 3/30 VC 3/48 VC or 3/30 VC 1) rocess value (option) 4 20m, galvanic insulation Loop resistance: 1100 Ω at 32 V The compact 8032 is proposed with ON/OFF output, or with external setpoints and/or process value outputs or also in S interface version. The remote 8032 has a transistor output. The connection to the process in the piping is done with the quarter-turn technique of the INLINE fittings. Electronic module data (continued) 800 Ω at 24 V 500 Ω at 18 V Input External Setpoint m, galvanic insulation Max. input impedance: 250 Ω Input frequency 8032 remote ulse signal: 2 to 400 Hz Input impedance: 10 kω Fieldbus S-Interface Current consumption 8032 Max. 80 m (no load) 8032 remote Max. 50 m (no load) + remote sensor current consumption Materials Housing C +20% glass fi ber Seal FKM (EM option) Front panel folio olyester Wall mounted holder VC Electrical connections Cable plug EN Multipin 5 pin M12/ 4 pin M12 / 8 pin M12 General data mbient temperature 32 F up to 140 F (0 to 60 C) Voltage supply cable Cross section 0.14 up to 0.5 mm² Recommended length Max. 100m, shielded Remote sensor connection length Max. length /Max. cross section 50 m / 0.5 mm² rotection class I65 with cable plug Standards EMC EN , Security EN Vibration EN Shock EN ) Valid for: External setpoint input, process value output and S-interface usa.com age 1/12

2 imensions [mm] Type 8032 with brass or stainless steel fitting and threaded port connection. (imensions: see ordering chart for Type S030 compact body) lastic fitting with solvent or welded socket and union nut. (imensions: see ordering chart for Type S030 compact body) 8032 compact 8032 remote FLOW SWITCH 54.2 Main features isplay Large digital display with 8 characters (4 digital characters and 4 alphanumeric characters) Bargraph Software main features International measuring units 10-segment bargraph Teach-In for a better accuracy Simulation mode to test the programming of the switching points, in dry conditions 3 keys to go through the menus and program the device 8032 with standard On/Off output 2 switching modes for the output, either hysteresis or window, inverted or not Contact Hysteresis mode Hysteresis, inverted Contact Hysteresis, not inverted Contact Window mode Window, inverted Contact Window, not inverted OLO OHI OLO OHI OLO OHI OLO OHI rogrammable delay before switching ossible outputs depending on the version: relay, transistor NN, transistor N. age 2/12

3 Main features (continued) 8032 with external setpoint option The switching points are automatically adjusted by the 4-20 m input signal originating from a LC. ower supplied by the LC On/Off relay output 8032 with process value option This version delivers an electric signal whose value is the image of the measured quantity. On/Off relay output 4-20 m output External setpoint (4-20 m input) esign The Burkert Quarter-Turn technology Compact version Remote version SE32 S030 Wall-mounted holder ressure temperature chart for plastic fittings with INLINE sensors ressure [psi] Errors in measurement chart Max. error [%] (related to the range) pplication range for complete device (fitting + transmitter) Flow velocity [f/s] Temperature [ F] resentation of max. errors in measurement in % Standard: ±(0.5% o.f.s. +2.5% o.r.) Teach-In: ±0.5% o.f.s. o.f.s. = of Full Scale (32.8 ft/s) o.r. = of Reading age 3/12

4 Ordering charts compact flow controller Type 8032 consists of 2 basis units as follows: 1. Compact electronic module SE32 2. INLINE fitting S030 (has to be ordered separately - see corresponding data sheet) Ordering chart display and electronic type SE32 for fitting S030 Input Output Connector Item no. * Voltage/ frequency Inputs Outputs Connection possibilities 1) External setpoint 2) rocess value output * Includes all neccesary electrical plugs Ordering chart for accessories ccessories Item no. Item no. * VC Si Bus NN transistor Conduit cable plug Type 2508, IN US08572 N transistor Conduit cable plug Type 2508, IN US08571 NN and N transistors 5-pin circular connector M12 US08570 NN and N transistors (UR/CS approved) 5-pin circular connector M12 US09678 Relay 5-pin circular connector M12 and conduit cable plug type 2508 IN m 1) Relay 5-pin circular connector M12 and conduit Si Si + Relay cable plug type 2508 IN pin circular connector M12 and conduit cable plug type 2508 IN ) VC 4 20 m 4-20 m 2) + Relay 8-pin circular connector M12 and conduit cable plug type 2508 IN US08569 US08568 US08567 US08566 Ordering chart for display / electronics for Type 8032 remote remote controller Type 8032 consists of 2 basis units as follows: 1. Remote electronic module SE32 2. Flow sensor type 8020, 8030, 8030-HT, 804 or frequency output with pulse signal (see corresponding data sheet). isplay and electronics Type 8032 remote version Voltage supply VC frequency NN and N M12 male 5 pins and M12 female 4 pins US07552 * Includes all neccesary electrical plugs 5 pin M12 female cable connector with plastic threaded locking ring pin M12 female connector moulded-on cable (2 m, shielded) pin M12 male cable connector with plastic threaded locking ring pin M12 male connector moulded-on cable (2 m, shielded) pin M12 female cable connector with plastic threaded locking ring pin M12 female connector moulded-on cable (2 m) pin M12 female coupler module for ribbon cable (S-Interface version only) age 4/12

5 Electrical connections Transistor version (NN/N) N 0 V V+ NN Transistor version NN or N with cable plug 2508 V+ (12-30 VC) 1 ground Sensor 1 V+ 2 Output NN 0 V Receiver V+ Load IN 0 V 3 0 V (0 VC) 3 2 transistor output Sensor 1 V+ N 4 Output 0 V 3 Receiver V+ IN Load 0 V Relay version Relay output ower supply 1 not connected V V+ not connected Relay version with external set point and process valve m-entry m-output m-output m-entry V V+ (12-30 VC) Not connected age 5/12

6 INLINE fitting dimensions [mm] Internal thread Stainless steel (316L - 1,4404) or brass (CuZn39b2) NT G Rc Orifice N L [mm] [mm] [mm] [inch] [mm] L 1/2 (15) NT 1/ G 1/ Rc 1/ /4 (20) NT 3/ G 3/ Rc 3/ (25) NT G Rc /4 (32) NT 1 1/ G 1 1/ Rc 1 1/ /2 (40) NT 1 1/ G 1 1/ Rc 1 1/ (50) NT G Rc Externall thread G Stainless steel (316L - 1,4404) or brass (CuZn39b2) or VC (only N6 and 8) or VF (only N 8) Orifice N L [mm] [mm] [mm] [inch] [mm] [mm] 1/4 (15) /4 or 1/2** /16 (8) /2** M16 x /2 (15) G 3/ /4 (20) G (25) G 1 1/ L 1 1/4 (32) G 1 1/ /2 (40) M 55 x (50) M 64 x ** NT, G or RC according fitting version Externall thread Stainless steel (316L - 1,4404) SMS1145 Orifice N [mm] [mm] [mm] Rd40 x 1/ Rd60 x 1/ Rd70 x 1/6 age 6/12

7 INLINE fitting dimensions [mm] Welding ends BS 4825 / SME BE Stainless steel (316L - 1,4404) ISO 4200 SMS 3008 IN Rg2 s Orifice N Standard S [mm] [mm] [mm] [mm] [mm] 5/16 (08) ISO SMS SME BE - - IN Rg /2 (15) ISO SMS SME BE - - IN Rg /4 (20) ISO SMS SME BE IN Rg (25) ISO SMS BS 4825/SME BE IN Rg /4 (32) ISO SMS BS 4825/SME BE IN RG /2 (40) ISO SMS BS 4825/SME BE IN Rg (50) ISO SMS BS 4820/SME BE IN Rg /2 (65) ISO SMS BS 4825/SME BE IN Rg2 - - age 7/12

8 INLINE fitting dimensions [mm] Tri-Clamp BS 4825 / SME BE* Stainless steel (316L - 1,4404) ISO (for pipe ISO 4200) SMS 3017 / ISO 2852* IN *vailable with internal surface finish Ra=0.8µm 2 1 Orifice N Standard 2 1 [mm] [mm] [mm] [mm] [mm] [mm] 5/16 (08) - - ISO (for pipe ISO 4200) SMS 3017/ISO SME BE IN /2 (15) ISO (for pipe ISO 4200) SMS 3017/ISO SME BE IN /4 (20) ISO (for pipe ISO 4200) SMS 3017/ISO SME BE IN (25) ISO (for pipe ISO 4200) SMS 3017/ISO BS 4825/SME BE IN /4 (32) ISO (for pipe ISO 4200) SMS 3017/ISO SME BE IN /2 (40) ISO (for pipe ISO 4200) SMS 3017/ISO BS 4825/SME BE IN (50) ISO (for pipe ISO 4200) SMS 3017/ISO BS 4825/SME BE IN /2 (65) SMS 3017/ISO BS 4825/SME BE IN age 8/12

9 INLINE fitting dimensions [mm] Flange Stainless steel (316L - 1,4404) 1 2 Z L NSI B IN 2633 (ISO N16) JIS 10K Orifice L Z 2 1 N IN/ NSI JIS NORM [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 1/2 (15) IN x NSI 4x JIS 4x /4 (20) IN x NSI 4x JIS 4x (25) IN x NSI 4x JIS 4x /4 (32) IN x NSI 4x JIS 4x /2 (40) IN x NSI 4x JIS 4x (50) IN x NSI 4x JIS 4x True union nut with solvent or fusion spigot VC,, VF Orifice N [mm] IN NSI JIS [IN] [NSI] [JIS] /4 (08)* /2 (15) /4 (20) (25) /4 (32) /2 (40) (50) Solvent or fusion spigot VC,, VF Orifice H L N VC VC VF VF [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] L H age 9/12

10 Ordering chart for fitting S030 ort connection Specification Seal Standards 1/4 (N6) 5/16 (N 8) 1/2 (N 15) Item no. / Orifice 3/4 (N 20) 1 (N 25) 1 1/4 (N 32) 1 1/2 (N 40) 2 (N 50) 2 1/2 (N 65) Brass - with VF paddle-wheel el - Temperature e max. 212 F, 230 SI (N16) Internal thread FKM NT G Rc (ISO7) External thread FKM NT G ) ) Rc (ISO7) x 1.5 mm Metric FKM Stainless steel - with VF paddle-wheel - Temperature max. 212 F, 230 SI (N16) Internal thread FKM NT G Rc (ISO7) External thread FKM NT G ) ) Rc (ISO7) EM SMS Weld ends FKM ISO ) Tri-Clamp Flange EM BS4825 / SME BE ) SMS IN Rg FKM ISO (for pipe ISO4200) EM BS4825/SME BE SMS3017/ISO BS4825/SME BE* SMS3017/ISO2852* IN FKM NSI B IN JIS 10K Stainless steel - with VF paddle-wheel - Temperature max. 212 F, 580 SI (N40) External thread FKM G * internal surface fi nish Ra = 0.8 µm Specification Item no. / Orifice port connection Seal Standards 1/4 (N 6) 5/16 (N 8) 1/2 (N 15) 3/4 (N 20) 1 (N 25) 1 1/4 (N 32) 1 1/2 (N 40) 2 (N 50) 2 1/2 (N 65) VC - with VF paddle-wheel - Temperature max. 122 F, 140 SI (N10) True union - solvent spigot FKM North merica version ISO Standard JIS Solvent ends FKM ISO External thread FKM G ) ) True union without spigot FKM EM (metric pipe only)- with VF paddle-wheel - Temperature max. 176 F, 140 SI (N10) True union - solvent spigot FKM ISO Solvent ends FKM ISO VF (metric pipe only)- with VF paddle-wheel - Temperature max. 212 F, 140 SI (N10) True union - solvent spigot FKM ISO Solvent ends FKM ISO External thread FKM G ) ) external thread 1/4" 2) external thread 1/2" 3) EM Seal 4) N20 only available in SME BE age 10/12

11 Interconnection possibilities with the compact Input 4-20 m (Ext. setpoint) Type On/Off flow transmitter/switch 4-20 m output Relay output Transistor output Type 2712 valve with Type 1067 positioner Type 5281 Solenoid valve Type 6212 Solenoid valve 8032 remote Type 8070 Low flow measurement Type 8030 For pipes with N 6 up to N 65 Type 8020 For pipes with N 6 up to N400 Type 8040 Flow measurement of contaminated fluids. For pipes with N 6 up to N400 Frequency input: pulse signal Type 8032 remote Type 6212 Solenoid valve Transistor output age 11/12

12 In case of special application conditions, We reserve the right to make technical 0602/4_US-en please consult for advice. changes without notice. age 12/12