Level Measurement. Continuous level measurement - Capacitance transmitters SITRANS LC300 5/271. Overview. Configuration

Transcription

1 Siemens G 200 Overview onfiguration Installation uild up of material in active shield area does not affect switch operation. Mounting on a bypass is an inverse frequency shift capacitance continuous level transmitter for liquids and solids applications. It is ideal for standard industrial applications in chemical, hydrocarbon processing, food and beverage, water, wastewater, and mining, aggregate, and cement industries. enefits Patented ctive-shield technology so measurement is unaffected by material buildup in active shield section Highly accurate and reliable PF-lined probes Integrated local L display 2-wire (4 to 20 m) current loop design urrent signalling according to NMUR NE 43 Push-button calibration and programming Stilling well (ground tube) version for low dielectric media and non-metallic vessels Install probe at least 0 mm (2") from tank wall. Note angle of repose and adjust accordingly. min. 0 (2) installation, dimensions in mm (inch) min. 0 (2) pplication is a 2-wire level measurement instrument combining a sophisticated, yet easy-to-adjust microprocessor with field-proven probes. It is available in four versions: rod, rod with stilling well, cable with PF insulation, and cable without PF insulation. Materials with low or high dielectric properties are accurately measured and patented ctive-shield technology helps in ignoring the effects of buildup or condensation near vessel nozzle. Key pplications: onductive and non-conductive media including: liquids and solids in standard industrial processes, bulk solids applications involving dust, and chemical processes involving vapour Siemens FI 0 20 /27

2 Siemens G 200 Technical specifications Input Measuring range Span Output Loop current ccuracy (transmitter) Temperature stability Non-linearity and repeatability ccuracy Rated operating conditions ) mbient conditions pf Min. 3.3 pf ontinuous signal m/ m according to NMUR % of actual capacitance value < 0.4 % of full scale and actual measurement value eviation < 0. % of actual measurement value mbient temperature ( F) 2) Installation category Pollution degree 4 Ingress protection Installation conditions Location Process pressure I Type 4/NEM 4/IP6 (optional IP68) Indoor/outdoor - to +3 bar g ( psi g) Process temperature º ( ºF) 3) Min. dielectric constant ε r. esign Material Enclosure Probe diameter Rod version able version ctive shield length luminum, epoxy-coated 9 mm (0.7") with PF jacket 9 mm (0.3") with PF jacket, 6 mm (0.24") without PF jacket Rod version threaded: 20 mm (4.72") flanged: 00 mm (3.94") able version threaded: 2 mm (4.92") flanged: 0 mm (4.3") Process connection of probe Threaded rod mounting Threaded cable mounting ¾",",¼", ½" NPT [(Taper), NSI/SME.20.] R ¾",", ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] G ¾",", ½" [(SPP), EN ISO 228-/PF (JIS-P), JIS 0202] ½" NPT [(Taper), NSI/SME.20.] R ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] G ½" [(SPP), EN ISO 228-/PF (JIS-P), JIS 0202] Flange mounting... 4" SME, N Enclosure cable inlet Power supply User Interface 2 x ½" NPT or 2 x M20x V any polarity, 2-wire current loop circuit isplay Local L, 4 digit, each and limited alpha characters Safety Measurement current signalling ccording to NMUR NE 43, signal m, fault 3.6 or 2 m (22 m) ertificates and approvals General ust Ignition Proof (Intrinsically Safe probe circuit) Flame Proof (Intrinsically Safe probe circuit) Explosion Proof (Intrinsically Safe probe circuit) Marine Overfill Protection Other ) 2) 3) E, S US/, FM, -TIK (Europe) TEX /2 T00 (US/anada) FM/S: lass II, iv., Groups E,F,G lass III T4 (Europe) TEX II /2 G EEx d [ia] II T6...T TEX II /2 T00 (US/anada) lass I, iv., Groups,,, lass II, iv., Groups E,F,G lass III T4 ureau Veritas Type pproval S Type pproval I-Vincotte Pattern pproval (hina) When operation is in areas classified as hazardous, observe restrictions according to relevant certificate. See also Pressure/Temperature curves on page /277. Thermal isolator is used if process connection temperature exceeds +8 (+8 F) Not suitable for steam environments esign: Probe Rod version Stilling well version Length Sensor wetted parts O-ring seal material Min. 300 mm (2"), max. 000 mm (97") PF, 36L stainless steel Min. 300 mm (2"), max. 000 mm (97") PF, 36L stainless steel able version Min. 000 mm (40"), max mm (984") 36L stainless steel or 36L stainless steel with PF insulation FKM or FFKM FKM or FFKM FKM or FFKM Thermal isolator Optional Optional Optional Options N/ N/ Mounting eye for PF insulated cable version /272 Siemens FI 0 20

3 Siemens G 200, rod version level transmitter for liquids and solids applications. Process onnection Threaded, 36L stainless steel ¾" NPT [(Taper), NSI/SME.20.] 0 " NPT [(Taper), NSI/SME.20.] 0 ¼" NPT [(Taper), NSI/SME.20.] 0 ½" NPT [(Taper), NSI/SME.20.] 0 R ¾" [(SPT), EN 0226/PT (JIS-T), JIS 0203] R " [(SPT), EN 0226/PT (JIS-T), JIS 0203] R ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] ) 7 M L G ¾" [(SPP), EN ISO 228-/PF (JIS-P), JIS 0202] 3 G " [(SPP), EN ISO 228-/PF (JIS-P), JIS 0202] 3 G ½" [(SPP), EN ISO 228-/PF (JIS-P), 3 JIS 0202] Welded flange, 36L stainless steel, raised face ) " SME, 0 lb " SME, 300 lb " SME, 600 lb ½" SME, 0 lb ½" SME, 300 lb E ½" SME, 600 lb F 2" SME, 0 lb G 2" SME, 300 lb H 2" SME, 600 lb J 3" SME, 0 lb K 3" SME, 300 lb L 3" SME, 600 lb M 4" SME, 0 lb N 4" SME, 300 lb P 4" SME, 600 lb Q Welded flange, 36L stainless steel, Type flat faced ) N 2, PN 6 6 N 2, PN 40 6 N 40, PN 6 6 N 40, PN 40 N 0, PN 6 N 0, PN 40 N 80, PN 6 N 80, PN 40 N 00, PN 6 N 00, PN E 6 F 6 G 6 H 6 J 6 K Probe Length (from flange face or including process thread) dd order code Y0 and plain text: "Insertion length... mm" mm ( ") mm ( ") mm ( ") mm ( ") mm ( ") E Thermal Isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 (+8 F)] Wetted Seals FKM 0 FFKM [for process temperatures above -20 (-4 F)] Probe Material 9 mm (0.7") diameter 36L stainless steel, PF lined rod 0, rod version level transmitter for liquids and solids applications. pprovals General Safety (S, FM, E, -TIK) E, -TIK, TEX II /2 T00 Flame Proof Enclosure With IS Probe E, -TIK, TEX II /2 G EEx d [ia] II T6...T, TEX II /2 T00 S/FM lass II, iv., Gr. E, F, G Explosion Proof Enclosure With IS Probe S/FM lass I, iv., Gr.,,, S/FM lass II, iv., Gr. E, F, G Enclosure luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 luminum epoxy coated 2 x M20 x. cable inlet, IP6 luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP68 luminum epoxy coated 2 x M20 x. cable inlet, IP68 ) Flange bolting patterns and facings dimensionally correspond to the applicable SME 6. or EN 092- standard. Further designs Please add "-Z" to and specify Order code(s). Insertion length, specify in plain text: Y0:... mm tag [69 x 0 mm (2.7 x.97")]: Measuring-point number/identification (max. 6 characters) specify in plain text cceptance test certificate: Manufacturer's test certificate M to IN 30, Part 8 and ISO 9000 Inspection ertificate Type 3. per EN 0204 Operating Instructions English French German Spanish Note: The Operating Instructions should be ordered as a separate line item on the order. This device is shipped with the Siemens Milltronics manual containing the complete TEX Quick Start and Operating Instructions library. ccessories Electronic transmitter kit (includes transmitter and driver) SITRNS R00 Remote display - see hapter 8 SITRNS R200 Remote display - see hapter 8 SITRNS R00 Remote display - see hapter 8 ) Subject to export regulations L: N, EN: ER99 ) 7 M L Order code Y0 Y 2 E ) 7ML998-HE02 7ML998-HE ) 7ML998-HE32 7ML998-HE2 ) 7ML830-KN Siemens FI 0 20 /273

4 Siemens G 200, stilling well version level transmitter for liquid applications. Process onnection Threaded, 36L stainless steel ½" NPT [(Taper), NSI/SME.20.] 0 R ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] G ½" [(SPP), EN ISO 228-/PF (JIS-P), JIS ] Welded flange, 36L stainless steel, raised face ) ½" SME, 0 lb ½" SME, 300 lb E ½" SME, 600 lb F 2" SME, 0 lb G 2" SME, 300 lb H 2" SME, 600 lb J 3" SME, 0 lb K 3" SME, 300 lb L 3" SME, 600 lb M 4" SME, 0 lb N 4" SME, 300 lb P 4" SME, 600 lb Q Welded flange, 36L stainless steel, Type flat faced ) N 40, PN 6 6 N 40, PN 40 6 N 0, PN 6 6 E N 0, PN 40 N 80, PN 6 N 80, PN 40 N 00, PN 6 N 00, PN 40 7 M L F 6 G 6 H 6 J 6 K Probe Length (from flange face or including process thread) dd order code Y0 and plain text: "Insertion length... mm" mm ( ") mm ( ") mm ( ") mm ( ") mm ( ") E Thermal Isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 (+8 F)] Wetted Seals FKM 0 FFKM [for process temperatures above -20 (-4 F)] Probe Material 3 mm (.38") diameter stilling well, with 9 mm (0.7") diameter 36L stainless steel, PF lined rod with PTFE spacers pprovals General Safety (S, FM, E, -TIK) E, -TIK, TEX II /2 T00 Flame Proof Enclosure With IS Probe E, -TIK, TEX II /2 G EEx d [ia] II T6...T, TEX II /2 T00 S/FM lass II, iv., Gr. E, F, G Explosion Proof Enclosure With IS Probe S/FM lass I, iv., Gr.,,, S/FM lass II, iv., Gr. E, F, G E, stilling well version level transmitter for liquid applications. Enclosure luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 luminum epoxy coated 2 x M20 x. cable inlet, IP6 luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP68 luminum epoxy coated 2 x M20 x. cable inlet, IP68 ) Flange bolting patterns and facings dimensionally correspond to the applicable SME 6. or EN 092- standard. Further designs Please add "-Z" to and specify Order code(s). Insertion length, specify in plain text: Y0:... mm tag [69 x 0 mm (2.7 x.97")]: Measuring-point number/identification (max. 6 characters) specify in plain text cceptance test certificate: Manufacturer's test certificate M to IN 30, Part 8 and ISO 9000 Inspection ertificate Type 3. per EN 0204 Operating Instructions English French German Spanish Note: The Operating Instructions should be ordered as a separate line item on the order. This device is shipped with the Siemens Milltronics manual containing the complete TEX Quick Start and Operating Instructions library. ccessories Electronic transmitter kit (includes transmitter and driver) SITRNS R00 Remote display - see hapter 8 SITRNS R200 Remote display - see hapter 8 SITRNS R00 Remote display - see hapter 8 ) Subject to export regulations L: N, EN: ER99 7 M L Order code Y0 Y 2 ) 7ML998-HE02 7ML998-HE ) 7ML998-HE32 7ML998-HE2 ) 7ML830-KN /274 Siemens FI 0 20

5 Siemens G 200, cable version level transmitter for non-conductive liquids and solids applications. Process onnection Threaded, 36L stainless steel ½" NPT [(Taper), NSI/SME.20.] 0 R ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] G ½" [(SPP), EN ISO 228-/PF (JIS-P), JIS ] Welded flange, 36L stainless steel, raised face ) ½" SME, 0 lb ½" SME, 300 lb E ½" SME, 600 lb F 2" SME, 0 lb G 2" SME, 300 lb H 2" SME, 600 lb J 3" SME, 0 lb K 3" SME, 300 lb L 3" SME, 600 lb M 4" SME, 0 lb N 4" SME, 300 lb P 4" SME, 600 lb Q Welded flange, 36L stainless steel, Type flat faced ) N 40, PN 6 6 N 40, PN 40 6 N 0, PN 6 6 E N 0, PN 40 N 80, PN 6 N 80, PN 40 N 00, PN 6 N 00, PN 40 ) 7 M L F 6 G 6 H 6 J 6 K Probe Length (from flange face or including process thread) dd order code Y0 and plain text: "Insertion length... mm" mm ( ") mm ( ") mm ( ") mm ( ") mm ( ") E mm ( ") F mm ( ") G mm ( ") 2) H mm ( ) 2) J mm ( ") 2) K mm ( ") 2) L mm ( ") 2) M mm ( ") 2) N Thermal Isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 (+8 F)] Wetted Seals FKM 0 FFKM [for process temperatures above -20 (-4 F)] Probe Material are 36L stainless steel cable and 36L stainless steel cable weight, tinned copper crimp, PTFE backing ring, PEEK isolator and PF lined active shield 0, cable version level transmitter for non-conductive liquids and solids applications. pprovals General Safety (S, FM, E, -TIK) E, -TIK, TEX II /2 T00 Flame Proof Enclosure With IS Probe E, -TIK, TEX II /2 G EEx d [ia] II T6...T, TEX II /2 T00 S/FM lass II, iv., Gr. E, F, G Explosion Proof Enclosure With IS Probe S/FM lass I, iv., Gr.,,, S/FM lass II, iv., Gr. E, F, G Enclosure luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 luminum epoxy coated 2 x M20 x. cable inlet, IP6 luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP68 luminum epoxy coated 2 x M20 x. cable inlet, IP68 ) Flange bolting patterns and facings dimensionally correspond to the applicable SME 6. or EN 092- standard. 2) able lengths from 000 (90.") to 2000 mm (984.2") can be used in non-conductive media. ontact Factory for assistance. Further designs Please add "-Z" to and specify Order code(s). Insertion length, specify in plain text: Y0:... mm tag [69 x 0 mm (2.7 x.97")]: Measuring-point number/identification (max. 6 characters) specify in plain text cceptance test certificate: Manufacturer's test certificate M to IN 30, Part 8 and ISO 9000 Inspection ertificate Type 3. per EN 0204 Operating Instructions English French German Spanish Note: The Operating Instructions should be ordered as a separate line item on the order. This device is shipped with the Siemens Milltronics manual containing the complete TEX Quick Start and Operating Instructions library. ccessories Electronic transmitter kit (includes transmitter and driver) SITRNS R00 Remote display - see hapter 8 SITRNS R200 Remote display - see hapter 8 SITRNS R00 Remote display - see hapter 8 ) Subject to export regulations L: N, EN: ER99 ) 7 M L Order code Y0 Y 2 E ) 7ML998-HE02 7ML998-HE ) 7ML998-HE32 7ML998-HE2 ) 7ML830-KN Siemens FI 0 20 /27

6 Siemens G 200, PF coated cable version level transmitter for liquids and solids applications. Process onnection Threaded, 36L stainless steel ½" NPT [(Taper), NSI/SME.20.] 0 R ½" [(SPT), EN 0226/PT (JIS-T), JIS 0203] G ½" [(SPP), EN ISO 228-/PF (JIS-P), JIS ] Welded flange, 36L stainless steel, raised face ) ½" SME, 0 lb ½" SME, 300 lb E ½" SME, 600 lb F 2" SME, 0 lb G 2" SME, 300 lb H 2" SME, 600 lb J 3" SME, 0 lb K 3" SME, 300 lb L 3" SME, 600 lb M 4" SME, 0 lb N 4" SME, 300 lb P 4" SME, 600 lb Q Welded flange, 36L stainless steel, Type flat faced ) N 40, PN 6 6 N 40, PN 40 6 N 0, PN 6 6 E N 0, PN 40 N 80, PN 6 N 80, PN 40 N 00, PN 6 N 00, PN 40 ) 7 M L F 6 G 6 H 6 J 6 K Probe Length (from flange face or including process thread) dd order code Y0 and plain text: "Insertion length... mm" mm ( ") mm ( ") mm ( ") mm ( ") mm ( ") E mm ( ") F mm ( ") G mm ( ") 2) H mm ( ) 2) J mm ( ") 2) K mm ( ") 2) L mm ( ") 2) M mm ( ") 2) N Thermal Isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over +8 (+8 F)] Wetted Seals FKM 0 FFKM [for process temperatures above -20 (-4 F)] Probe Material PF coated cable and 36L stainless steel cable weight, PEEK isolator and PF lined active shield pprovals General Safety (S, FM, E, -TIK) E, -TIK, TEX II /2 T00, PF coated cable version level transmitter for liquids and solids applications. Flame Proof Enclosure With IS Probe E, -TIK, TEX II /2 G EEx d [ia] II T6...T, TEX II /2 T00 S/FM lass II, iv., Gr. E, F, G Explosion Proof Enclosure With IS Probe S/FM lass I, iv., Gr.,,, S/FM lass II, iv., Gr. E, F, G Enclosure luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP6 luminum epoxy coated 2 x M20 x. cable inlet, IP6 luminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP68 luminum epoxy coated 2 x M20 x. cable inlet, IP68 Mounting eye Without Mounting eye 0 With mounting eye ) Flange bolting patterns and facings dimensionally correspond to the applicable SME 6. or EN 092- standard. 2) able lengths from 000 (90.") to 2000 mm (984.2") can be used in non-conductive media. ontact Factory for assistance. Further designs Please add "-Z" to and specify Order code(s). Insertion length, specify in plain text: Y0:... mm tag [69 x 0 mm (2.7 x.97")]: Measuring-point number/identification (max. 6 characters) specify in plain text cceptance test certificate: Manufacturer's test certificate M to IN 30, Part 8 and ISO 9000 Inspection ertificate Type 3. per EN 0204 Operating Instructions English French ) Subject to export regulations L: N, EN: ER99 Order code Y0 Y 2 E ) 7ML998-HE02 7ML998-HE German ) 7ML998-HE32 Spanish 7ML998-HE2 Note: The Operating Instructions should be ordered as a separate line item on the order. This device is shipped with the Siemens Milltronics manual containing the complete TEX Quick Start and Operating Instructions library. ccessories Electronic transmitter kit (includes transmitter and driver) SITRNS R00 Remote display - see hapter 8 SITRNS R200 Remote display - see hapter 8 SITRNS R00 Remote display - see hapter 8 ) 7 M L ) 7ML830-KN /276 Siemens FI 0 20

7 Siemens G 200 haracteristic curves Pressure/Temperature urve L300 Standard, Extended Rod and able Probes Threaded Process onnections (7ML670, 7ML67, 7ML672 and 7ML673) Permitted Operating Pressures P 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) atmospheric - bar (-4. psi) -0 º (-238 ºF) -00 º (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 º) (-0 º) -0 º (-8 ºF) -29 º (-20 ºF) 00 ºF (38 º) 200 ºF (93 º) 0 º RT 0 º 00 º (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 º) 0 º (302 ºF) 400 ºF (204 º) 200 º (392 ºF) 00 ºF (260 º) 20 º (482 ºF) Permitted Operating Temperature T Example: Permitted operating pressure = 30 bar (43 psi) at 7 Process Pressure/Temperature derating curves (7ML670, 7ML67, 7ML672 and 7ML673) Siemens FI 0 20 /277

8 Siemens G 200 Pressure/Temperature urve L300 Standard, Extended Rod and able Probes SME Flanged Process onnections (7ML670, 7ML67, 7ML620 and 7ML673) Permitted Operating Pressure P 90 bar (,30 psi) 80 bar (,60 psi) 70 bar (,0 psi) 60 bar (870 psi) 0 bar (72 psi) SME 600 ) 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) SME 300 ) atmospheric - bar (-4. psi) -0 º (-238 ºF) -00 º (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 º) (-0 º) -0 º (-8 ºF) -29 º (-20 ºF) 00 ºF (38 º) 200 ºF (93 º) 0 º RT 0 º 00 º (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 º) 0 º (302 ºF) 400 ºF (204 º) 200 º (392 ºF) 00 ºF (260 º) 20 º (482 ºF) 600 ºF (3 º) 300 º (72 ºF) 700 ºF (37 º) 30 º (662 ºF) SME 0 ) 400 º (72 ºF) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Process Pressure/Temperature derating curves (7ML670, 7ML67, 7ML672and 7ML673) Pressure/Temperature urve L300 Standard, Extended Rod and able Probes EN Flanged Process onnections (7ML670, 7ML60, 7ML620 and 7ML670) Permitted Operating Pressure P 40 bar (80 psi) 30 bar (43 psi) 20 bar (290 psi) PN 40 ) atmospheric - bar (-4. psi) -0 º (-238 ºF) -00 º (-48 ºF) 0 bar (4 psi) -40 ºF 4 ºF (-40 º) (-0 º) -0 º (-8 ºF) -29 º (-20 ºF) 00 ºF (38 º) 200 ºF (93 º) 0 º RT 0 º 00 º (32 ºF) (22 ºF) (22 ºF) 300 ºF (49 º) 0 º (302 ºF) 400 ºF (204 º) 200 º (392 ºF) 00 ºF (260 º) 20 º (482 ºF) 600 ºF (3 º) 300 º (72 ºF) 700 ºF (37 º) 30 º (662 ºF) 400 º (72 ºF) PN 6 ) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Process Pressure/Temperature derating curves (7ML670, 7ML67, 7ML672 and 7ML673) /278 Siemens FI 0 20

9 Siemens G 200 imensional drawings Threaded (7ML670) Threaded (7ML67) Lid clip Electronics/ enclosure PF insulated probe Ø9 (0.7) * = 30 (.8) Inactive tip * Y02 ) measuring length able version, non-insulated Threaded (7ML672) Lid 20 (0.79) Y0 (insertion length) min. = 300 (4) / max. = 000 (97) stilling well Vent PF insulated probe able version, insulated Threaded (7ML673) 2) 3) 20 (0.79) Ø9 (0.7) * Y02 ) Measuring length Y0 (insertion length) min. = 300 (4) / max. = 000 (97) Ø3 (.38) 2 cable entries /2" NPT or M20 x. 0 (.9) Note: Lid without window Thermal isolator M20: 3 (.32) /2" NPT: 0 (.9) 27 (0.83) ) Rod version Y02: Shield length = 00 mm (3.9") for threaded including process connection thread length, 00 mm (3.9") for welded flange 2) For non-conductive applications only. Non-insulated cable can be shortened on site. Weight is included in measuring length. 3) For liquids and solids applications. Insulated cable cannot be shortened. Weight is not included in measuring length. 4) For conductive materials, the measuring length includes the exposed PF insulated cable only. ny fluid contact with the upper rod assembly will result in a short circuit and incorrect readings. cable Ø6 (0.24) weight Y02 = 0 (4.3) 20 (9.84) Measuring length Y0 (insertion length) min. = 000 (40) / max. = 2000 (984) PF insulated cable Ø9 (0.3) weight (electrically isolated but not PF insulated) Y02 = 0 (4.3) Measuring length 30 (3.78) See note 4) Y0 (insertion length) min. = 000 (40) / max. = 2000 (984) Ø9 (0.3) Ø34, (.36) Mounting eye Ø2 (0.98) Ø2 (0.47) 30 (3.78) 20 (0.79) Ø32 (.26) Ø34, (.36) - Threaded Process onnections, dimensions in mm (inch) Siemens FI 0 20 /279

10 Siemens G 200 Welded Flange (7ML670) Welded Flange (7ML67) Lid clip Electronics/ enclosure Lid 2 cable entries /2" NPT or M20 x. M20: 3 (.32) /2" NPT: 0 (.9) PF insulated probe Ø9 (0.7) * = 30 (.8) inactive tip able version, non-insulated Welded Flange (7ML672) cable Ø6 (0.24) weight * 20 (9.84) Y02 ) measuring length Measuring length Y0 (insertion length) min. = 300 (4) / max. = 000 (97) Y0 (insertion length) min. = 000 (40) / max. = 2000 (984) stilling well Vent PF insulated probe able version, insulated Welded Flange (7ML673) 2) 3) Y02 = 0 (4.3) Ø9 (0.7) Ø3 (.38) PF insulated cable Ø9 (0.3) weight (electrically isolated but not PF insulated) Ø32 (.26) Ø34, (.36) * Y02 ) Measuring length Y02 = 0 (4.3) Measuring length 30 (3.78) Y0 (insertion length) min. = 300 (4) / max. = 000 (97) See note 4) 0 (.9) Y0 (insertion length) min. = 000 (40) / max. = 2000 (984) Flange lass Flange Facing (raised face) SME 0/300 SME 600/900 PN6/40 Note: ) Rod version Y02: Shield length = 00 mm (3.9") for threaded including process connection thread length, 00 mm (3.9") for welded flange. 2) For non-conductive applications only. Non-insulated cable can be shortened on site. Weight is included in measuring length. 3) For liquids and solids applications. Insulated cable cannot be shortened. Weight is not included in measuring length. 4) For conductive materials, the measuring length includes the exposed PF insulated cable only. ny fluid contact with the upper rod assembly will result in a short circuit and incorrect readings. Mounting eye Lid without window Ø9 (0.3) Ø34, (.36) Ø2 (0.98) Thermal isolator Facing thickness 2 (0.08) 7 (0.28) 2 (0.08) Ø2 (0.47) 30 (3.78) 20 (0.79) 27 (0.83) - Flanged Process onnections, dimensions in mm (inch) /280 Siemens FI 0 20

11 Siemens G 200 Schematics With safety barrier white (S) black (O) red (+) Without safety barrier orange (S) black (O) red (+) For factory software update use only 4 to 20 m (2-wire) current loop measurement signal (not polarity sensitive) Menu / function selector down / - button up / + button connections Siemens FI 0 20 /28