3 & 4 Wire Self Compensating Ultrasonic Transmitters - Standard Mtg.& Sanitary Ferrule Mtg.

Transcription

1 & 4 Wire Self ompensating Ultrasonic Transmitters - Standard Mtg.& Sanitary Ferrule Mtg. FETURES S.S. 1L Face Material c/w Tri-lamp Mtg. Base Simple push-button calibration (ccurate) Output 4-20 m / 20-4 m (Isolated on 4 Wire Model s only) Built-in temperature compensation Optional RS22 and RS485 ommunications with calibration, diagnostics and data logging software PL compatible (Modbus RTU) Three & Four Wire Operation Self cleaning operation of sensor face PPLITIONS Food and Beverages Pharmaceutical /Water hemical,oils, Wastewater,Solids 025 & 045 ENVIRONMENTL Temperature : Electronics Enclosure :- 40 to 140 F (- 40 to 0 ) ontinuous Operation Std.Mtg. & Sanitary Nozzle :- 40 to 140 F(- 40 to 0 ) No Steam leaning (IP) High Temp.(Teflon Sensor): - 40 to 2 F(- 40 to 10 ) (Std. Thread Mounting) S.S. Sanitary :- 40 to 2 F(- 40 to 10 ) for 1/2 Hr. (Ferrule & Face) Steam leaning. Remove sensor for longer leaning cycle,recommended. Not for ontinuous Operation Pressure : 5 bar Max. using High Temperature & Pressure Sensor pprovals N/S: 22.2 No M92 +2, E: IE :90 + 1:92 +2:95 UL: (2002) Installation ategory : lass II Range ode OPERTIONL ccuracy :+/-0.10% of max. range (in lab using 4-20 Ma current output) +/-0.25% of max. range (typically in field) Response Time: Standard Unit 2 - echo s / sec. : Fast Protocol **I.R echo s / sec. ** IF Required Beam ngle : degree at db Loss of Echo : Hold 1 min., 22m or 2 m output Temp. omp. : In transducer alibration : Push-button or programmable via optional communications port Diagnostics : (Echo Profile) via communications port MEHNIL onduit Entry : 1/2 NPT Hole (PV conduit only) Enclosure : PV-94V0 or luminum (25 KHz Excluded) Ingress Protection: NEM (IP8) Beam ngle 70 The Kingsway Peterborough, Ont. K9JW anada Fax: (705) info@abmsensor.com Std.Thread Mtg. & High Temp. BM imer Page #4 OPERTING RNGE In Liquids Sanitary Std. & High Temp. & Pressure Sensor Resolution Mounting TLOGUE # - On the Web return to Home Page & Refer to catalogue number Structure for ordering Information. In Product Documentation refer to page. ELETRIL SPEIFITIONS Power BM V 0 Hz or 20 V 50 Hz (+/-20%), 1.7 V BM00 D 12 to 0 VD, Vdc R load = (Vs - ) / 24 m Output 4-20 m Output.1 u resolution 750 Ohms (Isolated on 4 Wire only) Optional RS22 or RS485 communications port ( & 4 Wire Only) 025 Solids * 045 Solids * ft m ft m ft m mm mm mm.0 /1.0 NPT 7. Ø x 7. H.0 NPT.0 Ø x.0 H.0 / 2.0 NPT 2.0 Ø x 2.7 H ft / 2.0 NPT ft m ft m ft m mm mm mm.0 / 2.0 NPT 1.8 Ø x 2.25 H.0 / 1.5 NPT 1.5 Ø x 2.1 H.0 / 1.0 NPT 1.1 Ø x 2.0 H * Note Solids Range 1/2 Liquids Range Stated in hart above 10 7 R10

2 Red Yellow & 4 Wire Ultrasonic Sensors User Instruction Manual Inter-onnection Diagram Top View of Sensor (ccess over Removed) 70 The Kingsway Peterborough, Ont. K9JW anada Fax: (705) info@abmsensor.com 12 0 VD D Power Input Note - TB # 7 is onnected to TB # 4! & 4 wire Ultrasonic Level devices provide the power (voltage) to the current loop,so use passive resistive load at PL (controller) input. Terminal Block Status LED alibration Pushbutton NOTE Use only 1/2 NPT onduit Typical Installation /TX 2 RS22/485 1) Direct mounting ultrasonic sensor - Simply thread sensor directly into metal or plastic nozzle. 2) Do not mount in the center of a domed tank Vdc 115 / 20 Vac 0 / 50 Hz 1/2 NPT onduit Hole Process Mtg. 1,1 1/2,2, NPT Ultrasonic Sensor! IN /D OUT 4-20 m L2/N 7 - F1/8 250V 4 STTUS LIBRTION SWITH FUSE BM SENSOR TEH. IN LIBRTION PUSHBUTTON / Led Indicator For 4-20 m (750 ohm Max.) OPTIONL Programmable alibration & Diagnostics, Data Logging, RS22 or RS485 ommunications. Temperature ompensation for the speed of sound for ultrasonic. Operation - n ultrasonice pulse is transmitted from the BM sensor. The pulse travels to the surface being monitored and is reflected off this surface back to the sensor. The time of flight is divided by 2,corrected with temp. and converted to an output signal directly proportional to the material level. U R Y +/ 0.25% Deadzone S P N R E S O L U T I O N Per hart Material Level FULL 20 or 4 m LED EMPTY 4 or 20m WRNING-hanges or Modifications not expressly approved by BM Sensor Technology Inc. could void the user s authority to operate the equipment. Wiring Information - Ground shield at one end only. - ll terminal block wiring must be rated for 250V. - Power input wiring must be protected by a 15 double pole circuit breaker. - Terminal is for use only with equipment which has no live parts which are accessible. - Terminal is for use with equipment which maintains basic insulation from hazardous voltage under normal and single fault conditions. - onnection used at the remote end of external circuit. Recommended Wiring For Sensor Power Wire unshielded 22 WG, 00 V urrent Output 1 Pair shielded 24 WG, 00 V ommunication 1 Pair shielded 24 WG, 00 V For D Sensor Power & urrent output Wire shielded 24 WG, 00 V ommunication 1 Pair shielded 24 WG, 00 V alibration 4-20 or 20-4 m Output FULL alibrate 20 m or 4m (Set Near Target) 1. alibration mode LED color is Green. (for Radar Low Dielectric Materials has to be off) 2. Push button and hold until LED turns Yellow (20 m) or push button and hold until LED turns Red (4 m). Release button and observe LED flashes to acknowledge the calibration. EMPTY alibrate 4 m or 20 m (Set Far Target) 1. alibration mode LED color is Green 2. Push button and hold until LED turns Red (4 m) or push button and hold until LED turns Yellow (20 m). Release button at Yellow or Red and observe LED flashes to acknowledge the calibration. LOSS OF EHO 22m or 2 m (.5 m for 2 Wire) 1. To choose 22m press and hold button until the light goes off 2 flashes 2. To choose 2m press and hold button until the light goes off 1 flash DWG 10R4

3 BM Sensor Terminal BM Sensor Terminal SHIELD &4 Wire Ultrasonic Sensors ommunication Interconnection Dtl. 70 The Kingsway Peterborough, Ont. K9JW anada Fax: (705) Fig. # 1 RS22 onnection L2/N /TX 2 Red DB WHT. or BLK. Note onnect the shield to BM Sensor Terminal #4. Fig. # 2 RS485 onnection L2 / N /TX 2 Red WHT. or BLK. RS485 to RS22 onverter onnect Shield to Ground at one End Note onnect the shield to BM Sensor Terminal #. To P Serial Port onnect to Serial Port of P,use Extension able length as required,refer to Fig.# 1 or # 2 For Wiring Dtl. To Power Source FUSE VD m -- 4! RS22/485 /Tx 2 STTUS alibration BM Sensor alibration Switch & Status Led 1/2 PV onduit Only for PV Housings, Metal onduit not Recommended Except for Metal Housing. 1) Load Probe Gateway P Software into your P. (Select SETUP.EXE from installation D and follow instructions on the screen.) 2) lick on STRT and under PROGRMS select Probe Gateway P. ) Follow instruction in help file.

4 .25"(18.mm) & 4 Wire Ultrasonic Transmitters & BM imer Dimensional Dtl. 70 The Kingsway, Peterborough, Ont. K9JW anada Tel. (705) Web: Fax.(705) info@abmsensor.com L Ø0.750"( Typ. of 8) Ø7.500" Ø9"O.D. NSI 4" /150 lb Flange Ø5.07" "X" "X" L im s Required.950" (100.MM)Ø Nameplate Recess 1" NPT onduit onnection Thread On Wiring ccess over PV Or luminum 7."(185.4mm) Dia. 1/2" NPT onduit Entry 1 4 "- 28 UNRF Socket Head ap Screw ( Typ. of 4) 5.75" Electronics Enclosure PV Housing PV Or luminum " NPT For Sensor Mounting '' Ø0.75"( Typ. of 8) 1.07" " NPT Thread 1.808" D ia. 'D' 'B' Transducer 25 KHz Sensor PV L Dim.'D' 1/4"Thk. Rubber Mounting Gasket supplied Section 'X'-'X' BM imer Flange Mount Maximum ngle 15 Off Perpenpicular Transducer 45 KHz Sensor PV c/w BM imer Level Sensor Housing Model # Operating Operating Mounting Dimension Dimension Dimension Range Frequency Thread NPT '' 'B' 'D' BMX00-025UL 90' (27.4 m) 25 KHz "/1" 7.25"(194mm) N/ 5.75" (14mm) BMX00-045UL 0' (18.2 m) 45 KHz " 7.75" (197mm).0" (7.2mm).0" (7.2mm) BMX00-052UL 50' (15.2 m) 52 KHz "/2" 9." (2mm).05" (77.5mm) 2.2" (55.9mm) BMX00-070UL 0' (9.1 m) 70 KHz "/2" 8.5" (21mm) 2.25" (57.2mm) 1.8" (45.7mm) BMX00-080UL 20' (.1 m) 80 KHz "/2" 8.5" (21mm) 2.25" (57.2mm) 1.8" (45.7mm) BMX00-081UL 1' (4.9 m) 81 KHz "/1.5" 8.4" (21mm) 2.1" (5.mm) 1.5" (8.1mm) BMX00-148UL 9' (2.7 m) 148 KHz 1" 8.25" (210mm) 2.0" (50.8mm) 1.1" (27.9mm) 10970R1

5 & 4 Wire Sanitary Ultrasonic Sensors Outline Dimensional Dtl. 70 The Kingsway Peterborough, Ont. K9JW anada Fax: (705) info@abmsensor.com Model # Serial # I.D.# pprovals Nameplate.950"(100.MM)Ø Thead on cess over cess over PV or luminum 1/2" NPT onduit Entry Housing PV or luminum (PV Housing shown).1" " NPT Thread is located on the Housing as shown 1.0" Ferrule 1.5" Ø = 2.2" Ferrule 2" Ø = 2.2" /4 Wire Ultrasonic Sensor Sanitary Ferrule O.D. Level Sensor Housing Model # Operating Operating Sanitary Ferrule O.D. Range Freq. 1 2" 1 2" BM /4XX-070UL 0' (9.1 m) 70 KHz N/ 2.5" BM /4XX-080UL 20' (.1 m) 80 KHz N/ 2.5" BM /4XX-081UL 1' (4.9 m) 81 KHz N/ 2.5" BM /4XX-1480UL 9' (2.7 m) 148 KHz 1.9" 2.5" 10875sht.1